Pyle PLMRKT12BK car media receiver
Contents
1. 450 KHz 36 dBu TROUBLE SHOOTING Before going through the checklist check wiring connection If any of the problems persist after checklist has been made consult your nearest service dealer Symptom Cause Solution No power The car ignition switch is If the power supply is not on connected to the car accessory circuits but the engine is not moving switch the ignition key to ACC The fuse is blown No sound Volume is in minimum Adjust volume to a desired level Wiring is not properly Check wiring connection connected The operation keys The built in microcomputer Press the RESET button do not work is not operating properly Front panel is not properly fixed due to noise into its place The radio does not The antenna cable is not Insert the antenna cable firmly work The radio connected station automatic selection does not The signals are too weak Select a station manually work 8800 0C3023 022. 25 04 um 1 3 OPERATION SWITHCHING ON OFF THE UNIT Switch on the unit by pressing any button When system is on press button 1 to turn off the unit SOUND ADJUSTMENT Press SEL button 3 shortly to select the desired adjustment mode The adjustment mode will change in the following order VOL BAS TRE BAL FAD gt Volume 1 Bass reble y Calanco Faden By rotating the audio knob 3 it is possible to adjust the desired sound quality LOUDNESS Press BND LOU button 4 for several seconds to reinforce the bass output Press it for several seconds again to release this function DISPLAY Exhibit current frequency and activated functions on the display 6 AUXILIARY INPUT This unit can be connected to a portable audio player through the AUX IN jack 13 MUTE Press to mute the sound press it 8 again to resume the sound EQUALIZATION Press EQ button 7 to turn on equalization function and to select desired audio mode There are five kinds of mode as below gt FLAT gt CLASSICS gt M gt ROCK M gt DSP OFF REMOTE SENSOR Point the remote cantrol handset to the remote sensor IR 5 Press the function keys on the handset to control the system RESET FUNCTION RESET button 25 must be activated with either a ball point pen or thin metal object The RESET button is to be activated for the following reaso
3. button 16 or M6 button 15 to select directory downward or upward If the MPS WMA fold does not contain any directory there is no function of pressing M5 button 16 or M6 button 15 PAUSING PLAYING Press button 21 to pause CD player Press it again to resume play PREVIEWING ALL TRACKS Shortly press SCN button 20 to play first several seconds of each track stored in USB device Shortly press again to stop intro and listen to track Press and hold SCN button 20 to intro the tracks stored in the current directory Press and hold it will exit the intro REPEATING THE SAME TRACK Shortly press RPT button 19 to continuously repeat the same track Shortly press it again to stop repeat Press and hold RPT button 19 will repeat all the tracks stored in the current directory Press and hold it again to stop repeat PLAYING ALL TRACKS IN RANDOM Shortly press SHF button 17 to play all tracks stored in USB device in random order Shortly press it again to cancel the function Press and hold SHF button 17 will play all tracks in the current directory in the random order press and hold it again will exit this mode OPERATION e SELECTING TRACKS BY AS PS Navi SCH BUTTON AS PS Navi SCH button is assigned as file searching button in MP3 file operation When pressed it is activated as selecting each mode of Digital Audio Searching track number gt Navigation from root by volume knob Navig
4. PYLE PLMRKTI2 OWNER S MANUAL Mobile Audio System e PLL Synthesizer Stereo Radio e Automatic Memory Storing Preset Equalization e USB Interface Auxiliary Input Function e Remote Control www pyleaudio com CONTENTS Installation eese 3 Take out screw before installation 3 DIN Front Mount Method A 3 Installing the unit 3 Removing the 4 DIN Rear Mount Method 5 Wiring Connection 6 Operatlorn iine 7 Location of 7 Switching on off the unit 8 Sound adjustment 8 ele 8 Display eerie eR 8 Y 8 Eoualtzatton 8 Remote sensor 8 Reset 8 Radio operation 8 Switching to radio mode 8 Selecting the frequency band 8 Selecting station 8 Automatic memory storing amp program 8 Station storing ees 9 DOAN eU C 9 9 Weather band selection 9 USB play operation 9 SD MMC operation 11 Specifica
5. ation from current directory by volume knob Searching Track Directly Press AS PS Navi SCH button for one time It enters into Selecting track number mode You can use the volume knob 3 to search the track number Rotate the knob clockwise or counter clockwise to increase or decrease the track number in a sequence The corresponding track number such as TRACK 12 will appear on the display You can also use the M6 15 and M5 16 buttons to fast select the track number Each time when you press M6 button 15 or M5 button 16 you can increase or decrease ten track numbers Such as track 12 will skip to track 22 Searching Directory or File Name Press AS PS Navi SCH button for two times The unit searches file or directory from root by volume knob 3 Display will list all available directories and songs Select the desired directory songs by using volume knob and BND LOU ENT button to confirm If the selected title is a song it starts to play If the selected title is a directory name then use the volume knob to list all songs under this directory and select the title Press BND LOU ENT button to confirm and start to play Repeat the above steps if the newly selected title is again a directory Searching From Current Directory Press AS PS Navi SCH button for three times The unit searches file or directory from current directory by the volume knob The current directory name and the currently playing fil
6. d be careful not to pinch any wires or cables 8 Slide the unit into the sleeve until it locks into place 9 To further secure the unit use the supplied metal strap to secure the back of the unit in place Use the supplied hardware Hex Nut M5mm and Spring Washer to attach one end of the strap to the mounting bolt on the back of the unit If necessary bend the metal strap to fit your vehicle s mounting area Then use the supplied hardware Tapping Screw 5x25mm and Plain Washer to attach the other end of metal strap to a solid metal part of the vehicle under the dashboard This strap also helps ensure proper electrical grounding of the unit Note to install the short threading terminal of the mounting bolt to the back of the unit and the other long threading terminal to the dashboard Spring Washer Hex Nut Metal Strap Mounting Bolt Plain Washer Tapping Screw 10 Reconnect the cable to the vehicle battery s negative terminal Then replace the outer trim ring and install the unit s front panel see the steps of to install the front panel Removing the unit 1 Make sure the ignition is turned off then disconnect the cable from the vehicle battery s negative terminal 2 Remove the metal strap attached the back of the unit if attached 3 Press the release button to remove the front panel 4 Lift the top of the outer trim ring then pull it out to remove it 5 Insert both of the suppli
7. e name are displayed selected The user can select the directory or file in the directory by volume knob The selected file can be played by pressing BND LOU ENT button DISPLAY INFORMATION Press DISP button 9 to show following information such as the clock ID3 TAG if available song title directory name artist name other contents and other information Note The main unit can only support the standard USB memory disc which is approved by Microsoft USB player is not a standard which means different brand name or different models have their own standard So our product cannot support every MP3 player When connecting an MP3 player and there has normal battery in the player non rechargeable battery you should remove the battery from the MP3 player then connect it to the USB interface Otherwise it may cause battery burst e When in USB play mode be sure not to remove the USB driver from the USB interface OPERATION SUPPORTED MP3 WMA DECODING MODES The main unit supports MP3 WMA Windows Media Audio decoding modes as below Standard Bit Rate kbps Supports Mode MPEG1 Audio 32 48 64 96 Stereo Layer 3 128 192 256 44 1kHz 320 Windows 64 96 128 Stereo Media Audio 192 44 1kHz The USB solution can support 1 Folder 500 max 2 File 999 max 3 Depth of folder 8 layers 4 Size 1 GB CAUTION When there are important file
8. ed keys into the slots at the middle left and right sides of the unit then pull the unit out of the dashboard INSTALLATION DIN REAR MOUNT Method B If your vehicle is a Nissan Toyota follow these mounting instructions Use the screw holes marked T Toyota N Nissan located on both sides of the unit to fasten the unit to the factory radio mounting brackets supplied with your vehicle Side view showing Screw Holes marked T N Factory Radio Mounting Bracket 227 Screw 7 NUN To fasten the unit to the factory radio mounting brackets Align the screw holes on the bracket with the screw holes on the unit and then tighten the screws 5x5mm on each side Note the outer trim ring sleeve and the metal strap are not used for method B installation WIRING CONNECTION MAIN UNIT ANTENNA CONNECTOR FUSE IGNITION RED SWITCH ACC MEMORY YELLOW FUSE BACK UP GRE GROUND BLAK l RCA CABLE Rch RED Lch WHITE POWER BLUE ANTENNA FRONTLch WHITE GREY FRONT SPEAKER SPEAKER WHITE BLACK GREY BLACK GREEN VIOLET REAR Lch REARRch SPEAKER SPEAKER GREEN BLACK VIOLET BLACK OPERATION LOCATION OF KEYS 7 8 09 60 a 62 D mm p
9. ns Initial installation of the unit when all wiring is completed All the function buttons do not operate Error symbol on the display Note If press RESET button 25 the unit can t work yet please use a cotton swab soaked in isopropyl alcohol to clean the socket on the back of the front panel RADIO OPERATION SWITCHING TO RADIO MODE Press MODE button 11 shortly to select radio mode the radio mode appears in the display together with the memory band and frequency e SELECTING THE FREQUENCY BAND At radio mode press BND LOU ENT button 4 shortly to select the desired band The reception band will change in the following order 1 9 2 4 3 9 SELECTING STATION Press button 2 lt lt button 24 shortly to activate automatic seek function Press for several seconds until MANUAL appears on the display the manual tuning mode is selected If both buttons have not been pressed for several seconds they will return to seek tuning mode and AUTO appears on the display AUTOMATIC MEMORY STORING amp PROGRAM SCANNING Automatic Memory Storing Press AS PS button 10 for several seconds the radio searches from the current frequency and checks the signal strength until one cycle search is finished And then 6 strongest stations are stored into the corresponding preset number button Program Scanning Press AS PS button 10 shortly to scan preset stati
10. on When the field strength level is more than the threshold level of stop level the radio is holding at that preset number for several seconds with releasing mute then searches again OPERATION STATION STORING Press any one of the preset button 18 1 to 6 to select a station which had been stored in the memory Press this button for several seconds until 2ND beeps come out current station is stored into the number button e SCAN Press it to set the function to scan 23 mode which scanning to higher frequency station with receivable signal and keep on each station for several seconds MONO STEREO Press the button to set the reception between mono 14 mode or stereo mode USB PLAY OPERATION In the front panel of the unit there is an USB interface 12 You can connect an USB driver through this interface 12 For the unit with no SD MMC interface when you connect an USB driver through the interface the unit will search the MP3 files or WMA files in the USB driver and start to play MP3 files or WMA files automatically If in other mode you can also press MODE button 11 to select USB mode It supports the MP3 WMA file in the device the operation please refer to the following instruction SELECTING TRACKS IN SINGLE STEP Press lt lt button 24 button 2 to move to the previous track or the following track Track number shows on display SELECTING TRACKS IN SINGLE STEP Press M5
11. s in the USB device do not connect it to the main unit to play And don t play the CD R RW disc that has important files in it Because any wrong operation may cause files loss And our company assumes no responsibility for this SD MMC OPERATION There is a SD MMC interface 22 on the front panel of the unit When you insert a SD MMC card in the SD MMC interface the unit will search the MP3 files or WMA files in the card and start to play MP3 files or WMA files automatically The operation is the same with the operation described above If in other mode you can also press MODE button 11 to select SD MMC mode When there is no USB driver in the USB interface you cannot record to SD MMC directly When there are important files in the SD MNC card do not connect it to the main unit to play SPECIFICATION GENERAL Power Supply Requirements Chassis Dimensions Tone Controls Bass at 100 Hz Treble at 10 KHz Maximum Output Power Current Drain CD PLAYER Signal to Noise Ratio Channel Separation Frequency Response RADIO Frequency Coverage Sensitivity S N 30 dB Stereo Separation Frequency Coverage IF Sensitivity S N 20 dB DC 12 Volts Negative Ground 178 W x 160 D x 50 H 10 dB 10 dB 4 x 40 Watts 15 Ampere max More than 55 dB More than 45 dB 40Hz 18 KHz FM 87 5 to 107 9 MHz 10 7 MHz 4uV gt 25dB AM 530 to 1710 KHz
12. se remove the two screws Take out screw before installation DIN FRONT MOUNT Method A Installation Opening This unit can be installed in any dashboard having an opening as show below 53 mm Installing the unit Be sure you test all connections first and then follow these steps to install the unit 1 Make sure the ignition is turned off and then disconnect the cable from the vehicle battery s negative terminal 2 Disconnect the wire harness and the antenna 3 Press the release button on the front panel and remove the control panel see the steps of to detach front panel 4 Lift the top of the outer trim ring then pull it out to remove it 5 The two supplied keys release tabs inside the unit s sleeve so you can remove it Insert the keys as far as they will go with the notches facing up into the appropriate slots at the middle left and right sides of the unit Then slide the sleeve off the back of the unit INSTALLATION Sleeve L Key Outer Trim Ring Front Panel 6 Mount the sleeve by inserting the sleeve into the opening of the dashboard and bend open the tabs located around the sleeve with a screwdriver Not all tabs will be able to make contact so examine which ones will be most effective Bending open the appropriate tabs behind the dashboard to secure the sleeve in place Dashboard Sleeve 7 Reconnect the wire harness and the antenna an
13. tion eee 12 Trouble shooting 13 INSTALLATION Notes Choose the mounting location where the unit will not interfere with the normal driving function of the driver Before finally installing the unit connect the wiring temporarily and make sure it is all connected up properly and the unit and the system work properly Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions Consult with your nearest dealer if installation requires the drilling of holes or other modifications of the vehicle Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop If installation angle exceeds 30 from horizontal the unit might not give its optimum performance did Avoid installing the unit where it would be subject to high temperature such as from direct sunlight or from hot air from the heater or where it would be subject to dust dirt or excessive vibration DIN FRONT REAR MOUNT This unit can be properly installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes at the sides of the unit chassis For details refer to the following illustrated installation methods TAKE OUT SCREW BEFORE INSTALLATION Before install the unit plea
Download Pdf Manuals
Related Search