LG E2241S-PN
Contents
1. 5 Once assembled take the monitor up carefully and face the front side Important This illustration depicts the general model of connection Your monitor may differ from the items shown in the picture Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display Disassembling the stand 1 Puta cushion or soft cloth on aflat 2 Place the monitor face Down on the surface cushion or soft cloth 3 Remove the Stand Body and 4 Use a coin on the back of the Stand Stand Base from product in Base and turn the screw anticlock correct direction as shown in the wise to loosen picture Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Connecting the stand B type 1 Place the monitor with its front facing downward on a soft cloth 2 Assemble the Stand Body into the 3 Assemble the Stand Base Front product in the correct direction as shown in Rear into the Stand Body in the the picture Make sure you push it until you correct direction hear it click ge Body Stand Bod Stand Body E 4 Once assembled take the monitor up carefully and face the front side Stand Base Important This illustration depicts the general model of connection Your monitor may differ from the items shown in the pictur2. Press the SUPER ENERGY SAVING Button then the main menu of the OSD appears Menu Name Sub menus SUPER ENERGY SAVING oe ON OFF RESET TOTAL POWER REDUCTION 20W cons TOTAL CO2 REDUCTION 16g EXIT Exit lt gt Move amp Restart to select sub menu Button Tip NOTE s OSD On Screen Display menu languages on the monitor may differ from the manual On Screen Display OSD Selection and Adjustment Main menu Sub menu SUPER ENERGY SAVING O N RESET TOTAL POWER REDUCTION 20W TOTAL CO2 REDUCTION 16g TOTAL POWER REDUCTION 20W TOTAL CO2 REDUCTION 16g RESET SUPER ENERGY SAVING ON OFF TOTAL POWER REDUCTION 20W TOTAL CO2 REDUCTION 16g Exit Exit lt P Move Select another sub menu OK Select Description Turn on the SUPER ENERGY SAVING fuction When current setting value is ON the SUPER SAVING color is green Turn off the SUPER ENERGY SAVING function Now the monitor is LED SAVING function When current setting value is OFF the SUPER SAVING color is gray Clear the TOTAL POWER REDUCTION and TOTAL CO2 REDUCTION values THE ENERGY SAVING WILL BE DELETED TOTAL POWER REDUCTION How much power is saved during using the monitor TOTAL CO2 REDUCTION Change the TOTAL POWER REDUCTION to CO2 On Screen Display OSD Selection and Adjustment NOTE SAVING DATA W h a Saving
3. LG Life s Good OWNER S MANUAL LCD MONITOR Please read this manual carefully before operating your set and retain it for future reference LCD MONITOR MODEL E1941T E1941S E2041T E2041S E2241T E2241S E2341T E244 1T www lg com Important Precautions This unit has been engineered and manufactured to ensure your personal safety however improper use may result in potential electrical shock or fire hazards In order to allow the proper operation of all safeguards incorporated in this display observe the following basic rules for its installation use and servicing On Safety Use only the power cord supplied with the unit In case you use another power cord make sure that it is certified by the applicable national standards if not being provided by the supplier If the power cable is faulty in any way please contact the manufacturer or the nearest authorized repair service provider for a replacement The power supply cord is used as the main disconnection device Ensure that the socket outlet is easily accessible after installation Operate the display only from a power source indicated in the specifications of this manual or listed on the display If you are not sure what type of power supply you have in your home consult with your dealer Overloaded AC outlets and extension cords are dangerous So are frayed power cords and broken plugs They may result in a shock or fire hazard Call your service technician f
4. On Mode 18 W Typ Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 44 30 cm 17 44 inch Width 44 30 cm 17 44 inch Height 35 00 cm 13 78 inch Height 28 50 cm 11 22 inch Depth 16 60 cm 6 54 inch Depth 5 5cm 2 16inch Weight excl packing 2 8 kg 6 17 Ib Tiit 5 tons AC 100 240 V 50 60 Hz 0 8 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice Specifications E1941S 47 0 cm 18 5 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 47 0 cm 0 300 mm x 0 300 mm Pixel pitch Horizontal Freq 30 kHz to 61 kHz Automatic Vertical Freq 56 Hz to 75 Hz Automatic Input Form Separate Sync Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7 Vp p 75 ohm Max VESA 1366 x 768 60 Hz Recommend VESA 1366 x 768 60 Hz DDC 2B On Mode 18 W Typ Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 44 30 cm 17 44 inch Width 44 30 cm 17 44 inch Height 35 00 cm 13 78 inch Height 28 50 cm 11 22 inch Depth 16 60cm 6 54 inch Depth 5 5cm 2 16inch Weight excl packing 2 8 kg 6 17 Ib Tilt 5 to 15 AC 100 240 V 50 60 H
5. On Disposal a Do not dispose of this product with general household waste Disposal of this product must be carried out in accordance to the regulations of your local authority Accessories Thank for selecting LGE products Please make sure the following items are included with your monitor If any items are missing contact your dealer DVI D Signal Cable 15 pin D Sub Signal Cable Only E1941T E2041T E2241T TO setit up this signal cable may be E2341T E2441T attached to this product before shipping out This feature is not available in all countries NOTE a This accessories may look different from those shown here User must use shielded signal interface cables D sub 15 pin cable DVI D cable with ferrite cores to maintain standard compliance for the product Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Connecting the stand A type 1 Place the monitor with its front facing downward on a soft cloth 2 Assemble the Stand Body into the 3 Assemble the Stand Base Front product in the correct direction as shown in Rear into the Stand Body in the the picture Make sure you push it until you correct direction hear it click inge Body Stand Body Stand Body i Stand Base 4 Use a coin on the back of the stand base and turn the screw clockwise to tighten
6. Front Panel Controls E E1941T E2041T E2241T E2341T E2441T MONITOR SETUP T Aua SUPER MENU ENERGY AUTO INPUT EXIT SAVING E E1941S E2041S E2241S MONITOR SETUP eae SUPER MENW ENERGY AUTO 2 Exit SAVING Gp MENU Button OSD LOCKED UNLOCKED This function allows you to lock the current control settings so that they cannot be inadvertently changed Press and hold the MENU button for several seconds The message OSD LOCKED should appear You can unlock the OSD controls at any time by pushing the MENU button for several seconds The message OSD UNLOCKED should appear Control Panel Functions SUPER ENERGY Use this button to enter SUPER ENERGY SAVING SAVING Button AUTO Button PROCESSING AUTO IMAGE ADJUSTMENT O INPUT Button SOURCE Hot key 5 EXIT Button Power Button amp Power Indicator menu For more information refer to page 20 AUTO IMAGE ADJUSTMENT When adjusting your display settings always press the AUTO button on the MONITOR SETUP OSD Only Analog Mode This will automatically adjust your display image to the ideal settings for the current screen resolution size display mode The best display mode is E1941T E1941S 1366 x 768 E2041T E2041S 1600 x 900 E2241T E2241S E2341T E2441T 1920 x 1080 When two input signals are connected you can select the input signal D SUB DVI you want When only one signal is connected it is automatically detected The defa
7. 27 inch Height 32 20 cm 12 67 inch Depth 16 60 cm 6 54 inch Depth 5 80cm 2 28 inch Weight excl packing 3 4 kg 7 50 Ib Milt 5 to 15 AC 100 240 V 50 60 Hz 1 0 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice Specifications E2341T 58 4 cm 23 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 58 4 cm 0 265 mm x 0 265 mm Pixel pitch Horizontal Freq 30 kHz to 83 kHz Automatic Vertical Freq 56 Hz to 75 Hz Automatic Input Form Separate Sync Digital Signal Input 15 pin D Sub Connector DVI D Connector Digital Input Form RGB Analog 0 7 Vp p 75 ohm Digital Max VESA 1920 x 1080 60 Hz Recommend VESA 1920 x 1080 60 Hz DDC 2B Analog Digital On Mode 28 W Typ Sleep Mode 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 54 60 cm 21 49 inch Width 54 60 cm 21 49 inch Height 40 70 cm 16 02 inch Height 34 20 cm 13 46 inch Depth 20 20cm 7 95 inch Depth 5 7cm 2 24 inch Weight excl packing 3 4 kg 7 49 Ib Tilt 5 to 15 AC 100 240 V 50 60 Hz 1 0 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions T
8. model your display may differ from the view as shown When using a D Sub signal input cable connector for Macintosh gt MAC NOU TTT TTY c SSS SSS es Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector AC IN BARMA EEE Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure 3 Press the power button on the front panel to turn the power on When monitor power is turned on the Self Image Setting Function is executed automatically Only Analog Mode PROCESSING SELF IMAGE SETTING 4 Power Button NOTE Self Image Setting Function This function provides the user with optimal display settings When the user connects the monitor for the first time this function automatically adjusts the display to optimal settings for individual input signals AUTO Function When you encounter problems such as blurry screen blurred letters screen flicker or tilted screen while using the device or after changing screen resolution press the AUTO function button to improve resolution Connecting the Display E1941S E2041S E2241S Connecting with the PC 1 Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off 2 Connect signal
9. video card performance In this case please ask to the computer or the video card manufacturer Troubleshooting Display image is incorrect The screen color is e Check if the signal cable is properly connected mono or abnormal and use a screwdriver to fasten if necessary e Make sure the video card is properly inserted in the slot e Set the color setting higher than 24 bits true color at Control Panel Settings The screen blinks e Check if the screen is set to interlace mode and if yes change it to the recommend resolution Do you see an Unrecognized monitor Plug amp Play VESA DDC monitor found message Have you installed the e Be sure to install the display driver from the display display driver driver CD or diskette that comes with your display Or you can also download the driver from our web site http www lg com e Make sure to check if the video card supports Plug amp Play function Specifications E1941T 47 0 cm 18 5 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 47 0 cm 0 300 mm x 0 300 mm Pixel pitch Horizontal Freq 30 kHz to 61 kHz Automatic Vertical Freq 56 Hz to 75 Hz Automatic Input Form Separate Sync Digital Signal Input 15 pin D Sub Connector DVI D Connector Digital Input Form RGB Analog 0 7 Vp p 75 ohm Digital Max VESA 1366 x 768 60 Hz Recommend VESA 1366 x 768 60 Hz DDC 2B Analog Digital
10. when you so that they cannot be inadvertently changed push MENU button You can unlock the OSD controls at any time by pushing the MENU button for several seconds the message OSD UNLOCKED will appear Troubleshooting Display image is incorrect Display Position is e Press the AUTO button to automatically adjust incorrect your display image to the ideal setting On the screen e Press the AUTO button to automatically adjust background vertical your display image to the ideal setting bars or stripes are visible Any horizontal noise e Press the AUTO button to automatically adjust appearing in any your display image to the ideal setting image or characters are not clearly e Check Control Panel gt Display gt Settings and adjust the display to the recommended resolution or adjust the display image to the ideal setting Set the color setting higher than 24 bits true color portrayed IMPORTANT a Check Control Panel gt Display gt Settings and see if the frequency or the resolution were changed If yes readjust the video card to the recommend resolution a If the recommended resolution optimal resolution is not selected letters may be blurred and the screen may be dimmed truncated or biased Make sure to select the recommend resolution a The setting method can differ by computer and O S Operation System and resolution mentioned above may not be supported by the
11. Data depends on the Panel So those values should be different from each panel and panel vendor LG accumulate those values using integrated function with 10 minutes broadcast video signal LED Saving means that how much power can be saved using WLED Panel instead of CCFL panel SUPER Saving means that how much power can be more saved using SUPER ENERGY SAVING function Troubleshooting Check the following before calling for service No image appears Is the power cord of the e Check and see if the power cord is connected display connected properly to the power outlet Is the power indicator Press the Power button light on Is the power indicator e If the display is in power saving mode try moving flickering the mouse or pressing any key on the keyboard to bring up the screen e Try to turn on the PC Do you see an OUT OF This message appears when the signal from the RANGE message on PC video card is out of horizontal or vertical the screen frequency range of the display See the Specifications section of this manual and configure your display again Do you see a CHECK This message appears when the signal cable SIGNAL CABLE between your PC and your display is not message on the connected Check the signal cable and try again screen Do you see a OSD LOCKED message on the screen Do you see OSD e You can secure the current control settings LOCKED
12. WIDE ORIGINAL PRESET USER Switch to full screen mode according to input image signal Change the input image signal ratio to original This function works only if input resolution is lower than monitor ratio 16 9 Select the screen color e WARM Set the screen to warm color temperature e MEDIUM Set the screen to medium color temperature e COOL Set the screen to cool color temperature le RED Set your own red color levels GREEN Set your own green color levels le BLUE Set your own blue color levels On Screen Display OSD Selection and Adjustment Main menu Description CONTRAST MENU CONTRAST 70 LANGUAGE 4 ENGLISH gt To adjust the contrast of the screen FACTORY RESET 4 LANGUAGE Se To choose the language in which the E CTO e control names are displayed LANGUAGE 4 ENGLISH 1 17 gt FACTORY RESET 4 NO FACTORY RESET Restore all factory default settings except EE 70 LANGUAGE Lancuace moust gt Press the lt d gt buttons to reset SES TaD immediately Exit Exit 4 P gt V i Move Select another sub menu On Screen Display OSD Selection and Adjustment mum YOu were introduced to the procedure of selecting and adjusting an item using the OSD system Listed below are the icons icon names and icon descriptions of the all items shown on the Menu
13. b Connector DVI D Connector Digital Input Form RGB Analog 0 7 Vp p 75 ohm Digital Max VESA 1920 x 1080 60 Hz Recommend VESA 1920 x 1080 60 Hz DDC 2B Analog Digital On Mode a AE Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 50 90 cm 19 80 inch Width 50 90 cm 19 80 inch Height 38 80 cm 15 27 inch Height 32 20 cm 12 67 inch Depth 16 60 cm 6 54 inch Depth 5 80cm 2 28 inch Weight excl packing 3 4 kg 7 50 Ib Tilt 5 to 15 AC 100 240 V 50 60Hz1 0A Operating Conditions Temperature 10 Cto35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice Specifications E2241S 54 6 cm 21 5 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 54 6 cm 0 248 mm x 0 248 mm Pixel pitch Horizontal Freq 30 kHz to 83 kHz Automatic Vertical Freq 56 Hz to 75 Hz Automatic Input Form Separate Sync Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7 Vp p 75 ohm Max VESA 1920 x 1080 60 Hz Recommend VESA 1920 x 1080 60 Hz DDC 2B On Mode 24 W Typ Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 50 90 cm 19 80 inch Width 50 90 cm 19 80 inch Height 38 80 cm 15
14. ce the display where the power cord is subject to damage Do not use this display near water such as near a bathtub washbowl kitchen sink laundry tub in a wet basement or near a swimming pool Displays are provided with ventilation openings in the cabinet to allow the release of heat generated during operation If these openings are blocked built up heat can cause failures which may result in a fire hazard Therefore NEVER a Block the bottom ventilation slots by placing the display on a bed sofa rug etc Place the display in a built in enclosure unless proper ventilation is provided a Cover the openings with cloth or other material Place the display near or over a radiator or heat source Do not rub or strike the Active Matrix LCD with anything hard as this may scratch mar or damage the Active Matrix LCD permanently Do not press the LCD screen with your finger for a long time as this may cause some afterimages Some dot defects may appear as Red Green or Blue spots on the screen However this will have no impact or effect on the display performance If possible use the recommended resolution to obtain the best image quality for your LCD display If used under any mode except the recommended resolution some scaled or processed images may appear on the screen However this is characteristic of the fixed resolution LCD panel Leaving a fixed image on the screen for a long time may cause damage to the screen and ca
15. change device 1 Place the monitor with its front facing downward on a soft cloth 7 i ig C type A type 2 Remove the Stand Body and Stand Base 2 To disconnect the Stand Base from the from product in correct direction as shown Stand Body simply unfold the screw in the picture handle and turn counter clockwise to loosen the screw and disconnect the Stand Base from its body S B type 2 Nip Latch inside Take off the stand base from stand body Installing the Wall mount plate 3 Install the Wall mount plate Wall mount plate Separate purchase This is stand type or wall mount type and is connectable with Wall mount plate Please refer to the installation guide for more details which is provided when Wall mount plate is purchased Kensington Security Slot Connected to a locking cable that can be purchased separately at most computer stores lt Screw Mounting Interface Dimension gt Hole spacing 75 mm x 75 mm NOTE a VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications a Please use VESA standard as below 784 8 mm and under 30 9 inch Wall Mount Pad Thickness 2 6 mm Screw 6 4 0 mm x Pitch 0 7 mm x Length 10 mm 787 4 mm and above 31 0 inch Please use VESA standard wall mount pad and screws Make sure to read the Safety Precautions before using the product Keep the OWNER S MANUAL CD in an acces
16. e Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display Disassembling the stand 1 Puta cushion or soft cloth on aflat 2 Place the monitor face Down on the surface cushion or soft cloth Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Connecting the stand C type 1 Place the monitor with its front facing downward on a soft cloth 2 Assemble the Stand Body into the 3 Assemble the Stand Base Front product in the correct direction as shown in Rear into the Stand Body in the the picture Make sure you push it until you correct direction hear it click inge Body Stand Body 4 Turn the screw to the right to fix the Stand Body to the Stand Base Stand Base Screw Turn the screw by using the screw handle 5 Once assembled take the monitor up carefully and face the front side Important a This illustration depicts the general model of connection Your monitor may differ from the items shown in the picture Do not carry the product upside down holding only the stand base The product may fall and get damaged or injure your foot Connecting the Display Disassembling the stand 1 Puta cushion or soft cloth on aflat 2 Place the monitor face Down on the surface cushion or so
17. emperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice Specifications E2441T 60 97 cm 24 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 60 97 cm 0 277 mm x 0 277 mm Pixel pitch Horizontal Freq 30 kHz to 83 kHz Automatic Vertical Freq 56 Hz to 75 Hz Automatic Input Form Separate Sync Digital Signal Input 15 pin D Sub Connector DVI D Connector Digital Input Form RGB Analog 0 7 Vp p 75 ohm Digital Max VESA 1920 x 1080 60 Hz Recommend VESA 1920 x 1080 60 Hz DDC 2B Analog Digital On Mode 25 W Typ Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 56 93 cm 22 41 inch Width 56 93 cm 22 41 inch Height 41 91 cm 16 50 inch Height 35 43 cm 13 94 inch Depth 17 93cm 7 05 inch Depth 593cm 2 33 inch Weight excl packing 4 0 kg 8 81 Ib Tilt 5 to 15 AC 100 240 V 50 60Hz1 2A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice Preset Modes Resolution ME1941T E1941S If you can t select 1366 x 768 in display prope
18. ft cloth 3 To disconnect the Stand Base from the Stand Body simply unfold the screw handle and turn counter clockwise to loosen the screw and disconnect the Stand Base from its body Connecting the Display Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off Positioning your display After installation adjust the angle as shown below 1 Adjust the position of the panel in various ways for maximum comfort a Tilt Range 5 to 15 Do not touch or press the screen when adjusting the angle of the monitor a When adjusting the angle of the screen do not put your finger s in between the head of the monitor and the stand body You can hurt your finger s ERGONOMIC a It is recommended that in order to maintain an ergonomic and comfortable viewing position the forward tilt angle of the monitor should not exceed 5 degrees Connecting the Display E1941T E2041T E2241T E2341T E2441T Connecting with the PC 1 Before setting up the monitor ensure that the power to the monitor the computer system and other attached devices is turned off 2 Connect signal input cable Oo and power cord 2 in order then tighten the screw of the signal cable Connect DVI D Digital signal Cable Connect D sub Analog signal Cable NOTE a This is a simplified representation of the rear view a This rear view represents a general
19. input cable and power cord E in order then tighten the screw of the signal cable Connect D sub Analog signal Cable NOTE a This is a simplified representation of the rear view a This rear view represents a general model your display may differ from the view as shown When using a D Sub signal input cable connector for Macintosh p gt MAC Mac adapter For Apple Macintosh use a separate plug adapter is needed to change the 15 pin high density 3 row D sub VGA connector on the supplied cable to a 15 pin 2 row connector Varies according to model AC IN BRA Connect the signal input cable and tighten it up by turning in the direction of the arrow as shown in the figure 3 Press the power button on the front panel to turn the power on When monitor power is turned on the Self Image Setting Function is executed automatically E PROCESSING SELF IMAGE SETTING Power Button NOTE Self Image Setting Function This function provides the user with optimal display settings When the user connects the monitor for the first time this function automatically adjusts the display to optimal settings for individual input signals AUTO Function When you encounter problems such as blurry screen blurred letters screen flicker or tilted screen while using the device or after changing screen resolution press the AUTO function button to improve resolution Control Panel Functions
20. ject to change without notice Specifications E2041S 50 8 cm 20 0 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 50 8 cm 0 2766 mm x 0 2766 mm Pixel pitch Horizontal Freq 30 kHz to 83 kHz Automatic NOTE Vertical Freq 56 Hz to 75 Hz Automatic Input Form Separate Sync Signal Input 15 pin D Sub Connector Input Form RGB Analog 0 7 Vp p 75 ohm Max VESA 1600 x 900 60 Hz Recommend VESA 1600 x 900 60 Hz DDC 2B On Mode 20 W Typ Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 47 60 cm 18 74 inch Height 36 40 cm 14 33 inch Depth 16 60cm 6 54 inch Width 47 60 cm 18 74 inch Height 30 30 cm 11 92 inch Depth 5 70cm 2 24inch Weight excl packing 2 7 kg 5 95 Ib Tilt 5 to 15 AC 100 240 V 50 60 Hz 1 0 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type a Information in this document is subject to change without notice Specifications E2241T 54 6 cm 21 5 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 54 6 cm 0 248 mm x 0 248 mm Pixel pitch Horizontal Freq 30 kHz to 83 kHz Automatic Vertical Freq 56 Hz to 75 Hz Automatic Input Form Separate Sync Digital Signal Input 15 pin D Su
21. or replacement As long as this unit is connected to the AC wall outlet it is not disconnected from the AC power source even if the unit is turned off Do not Open the Display There are no user serviceable components inside a There are Dangerous High Voltages inside even when the power is OFF a Contact your dealer if the display is not operating properly To Avoid Personal Injury Do not place the display on a sloping shelf unless properly secured a Use only a stand recommended by the manufacturer Do not drop an object on or apply impact to the product Do not throw any toys or objects on the product screen It can Cause injury to human problem to product and damage the display To Prevent Fire or Hazards a Always turn the display OFF if you leave the room for more than a short period of time Never leave the display ON when leaving the house a Keep children from dropping or pushing objects into the display s cabinet openings Some internal parts carry hazardous voltages Do not add accessories that have not been designed for this display When the display is to be left unattended for an extended period of time unplug it from the wall outlet a In the presence of thunder and lightning never touch the power cord and signal cable because it can be very dangerous It can cause electric shock Important Precautions On Installation Do not allow anything to rest upon or roll over the power cord and do not pla
22. rty timing option please update your video card driver from your video card vendor Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz _ Polarity H V 1 720 x 400 31 468 70 2 640 x 480 31 469 60 3 640 x 480 37 500 75 4 800 x 600 37 879 60 5 800 x 600 46 875 75 6 832 x 624 49 725 75 7 1024 x 768 48 363 60 8 1024 x 768 60 123 75 9 1366 x 768 47 712 60 Recommend Mode E E2041T E2041S Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz Polarity H V 1 720 x 400 31 468 70 dt 2 640 x 480 31 469 60 A 3 640x480 37 500 75 ca 4 800x600 37 879 60 Ht 5 800x600 46 875 75 H4 6 1024x768 48 363 60 il 7 1024x768 60 123 75 8 1152x864 67 500 75 9 1600 x 900 60 000 60 H Recommend Mode E E22417 E2241S E23411 E2441T Display Modes Resolution Horizontal Freq kHz Vertical Freq Hz Polarity H V 1 720 x 400 31 468 70 2 640 x 480 31 469 60 3 640 x 480 37 500 75 4 800 x 600 37 879 60 5 800 x 600 46 875 75 6 1024 x 768 48 363 60 7 1024 x 768 60 123 75 8 1152 x 864 67 500 75 9 1280 x 1024 63 981 60 10 1280 x 1024 79 976 75 11 1680 x 1050 65 290 60 me 12 1920 x 1080 67 500 60 y4 Recommend Mode Indicator MtO DB LED Color On Mode Blue Sleep Mode Blue Blinking Off Mode Off Installing the Wall mount plate This monitor satisfies the specifications of the Wall mount plate or the inter
23. sible place for furture reference The model and serial number of the SET is located on the back or one side of the SET Record it below should you ever need service MODEL SERIAL Life s Good ENERGY STAR is a set of power saving guidelines issued by the U S Environmental Protection Agency EPA p J As an ENERGY STAR Partner LGE U S A Inc has determined that this product meets the ENERGY STAR guidelines for energy efficiency
24. signal input DVI D Digital signal input Main menu Sub menu Supported input Description SUB To adjust the brightness of the BRIGHTNESS C03 SSS ee ae eee E ov o Reig ORIGINAL RATIO COLOR TEMP PRESET USER To customize the color of the i Screen I i screen et ea ae eee ee ea eae ey ee an ee ae ee eee eee To customize the screen status for a user s operating Initialize the SUPER ENERGY SAVING and set to OFF mode environment i I al E i Tum on the SUPER ENERGY SAVING function I I I q W as sine ie TG Tum off the SUPER ENERGY 1 SAVING function 4 BS a eee ee ce ee I I I I I I I I I NOTE The order of icons may differ depending on the model 17 to 22 On Screen Display OSD Selection and Adjustment BRIGHTNESS ORIGINAL RATIO e COLOR TEMP PRESET Main menu 3 BRIGHTNESS gt 100 WIDE 4 4 PRESET gt 4 WARM gt ORIGINAL RATIO Sub menu BRIGHTNESS f ORIGINAL RATIO 4 WIDE 1 2 gt e COLOR TEMP PRESET COLOR TEMP MENU E gt 100 4 PRESET gt 4 WARM b BRIGHTNESS ORIGINAL RATIO PRESET Exit Exit sq pv E gt 100 4 WIDE gt COLOR TEMP 4 PRESET 1 2 gt 4 WARM gt Move Select another sub menu Description To adjust the brightness of the screen
25. ult setting is D Sub Only E1941T E2041T E2241T E2341T E2441T Exit the OSD On Screen Display Use this button to turn the display on or off The power indicator stays blue if the display is running properly On Mode If the display is in Sleep Mode the power indicator is blinking blue On Screen Display OSD Control Adjustment Screen Adjustment Making adjustments to the image size position and operating parameters of the display is quick and easy with the On Screen Display Control system A short example is given below to familiarize you with the use of the controls The following section is an outline of the available adjustments and selections you can make using the OSD To make adjustments in the On Screen Display follow these steps X BRIGHTNESS gt 100 WIDE gt fm ORIGINAL RATIO 4 COLOR TEMP 4 PRESET gt 4 PRESET gt Press the discretionary Button then the main menu of the OSD appears To access a control use the corresponding Buttons Use the 4 gt V Buttons to adjust the image to the desired level Use the Button to select other sub menu items 3 4 Press the EXIT Button to exit from the OSD On Screen Display OSD Selection and Adjustment The following table indicates all the On Screen Display control adjustment and setting menus CAT D SUB Analog
26. use image burn in Make sure to use a Screen saver on the product Burn in and related problems are not covered by the warranty on this product Do not shock or scratch the front and sides of the screen with metallic objects Otherwise it may cause damage to the screen Make sure the panel faces forward and hold it with both hands to move If you drop the product the damaged product can cause electric shock or fire Contact an authorized the service center for repair Avoid high temperatures and humidity Important Precautions On Cleaning a Unplug the display before cleaning the face of the display screen Use a slightly damp not wet cloth Do not use an aerosol directly on the display screen because over spraying may cause electrical shock a When cleaning the product unplug the power cord and scrub gently with a soft cloth to prevent scratching Do not clean with a wet cloth or spray water or other liquids directly onto the product An electric shock may occur Do not use chemicals such as benzene paint thinners or alcohol a Spray water onto a soft cloth 2 to 4 times and use it to clean the front frame wipe in one direction only Too much moisture may cause staining On Repacking a Do not throw away the carton and packing materials They make an ideal container in which to transport the unit When shipping the unit to another location repack it in its original material
27. z 0 8 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is subject to change without notice Specifications E2041T 50 8 cm 20 0 inch Flat Panel Active matrix TFT LCD Anti Glare coating Visible diagonal size 50 8 cm 0 2766 mm x 0 2766 mm Pixel pitch Horizontal Freq 30 kHz to 83 kHz Automatic Vertical Freq 56 Hz to 75 Hz Automatic Input Form Separate Sync Digital Signal Input 15 pin D Sub Connector DVI D Connector Digital Input Form RGB Analog 0 7 Vp p 75 ohm Digital Max VESA 1600 x 900 60 Hz Recommend VESA 1600 x 900 60 Hz DDC 2B Analog Digital On Mode ZO W Typ Sleep Mode lt 0 3 W Off Mode lt 0 3 W With Stand Without Stand Width 47 60 cm 18 74 inch Width 47 60 cm 18 74 inch Height 36 40 cm 14 33 inch Height 30 30 cm 11 92 inch Depth 16 60cm 6 54 inch Depth 5 70cm 2 24 inch Weight excl packing 2 7 kg 5 95 Ib Tilt 5 to 15 AC 100 240 V 50 60 Hz 1 0 A Operating Conditions Temperature 10 C to 35 C Humidity 10 to 80 non Condensing Storage Conditions Temperature 20 C to 60 C Humidity 5 to 90 non Condensing Attached Detached O Wall outlet type NOTE a Information in this document is sub
Download Pdf Manuals
Related Search