Manhattan 168175 uninterruptible power supply (UPS)
Contents
1. Connecting Cables User Manual MANHATTAN SAFETY INSTRUCTIONS Prior fo its operation inspect this product for damage If any damage is found notify your dealer Keep the carton and packing foam in the event the product must be returned fo the factory for service damage sustained in transit when shipped from the user is not covered under warranty Place the device indoors in an area that has adequate airflow and is free from excessive dust Do not allow the UPS to be exposed moisture rain excessive heat or direct sunlight Use of this product in life support applications where failure of this device can reasonably be expected to cause failure of life support equipment or to significantly affect its safety or effectiveness is nof recommended Always disconnect the input power cord from the wall outlet before replacing the battery Do not dispose of the battery in a fire as the battery may explode Do nof open or mutilate the battery as it contains a toxic electrolyte harmful to both the skin and eyes e e Proper disposal of the battery is required Refer to your local laws regulations regarding battery disposal When replacing batteries use the same number and type as listed in Specifications Only use tools with insulated handles and remove watches rings and bracelets OPERATION amp INSTALLATION This MANHATTAN Line Interactive UPS can protect your equipment from surges spikes blackouts br2. 35 minutes at varying loads typical with PC and 15 LCD monitor at 85 VV Recharge 8 hours typical 12 hours maximum Transfer 4 6 ms typical 10 ms maximum Communications port RS232 120 V RS232 220 V Teleohone tax network ports RJ 11 RJ 45 1 in 1 out surge protected Nominal voltage input 100 V 110 V 120 V 220 V 230 V 240 V output 120 V 230 V e Voltage range input 96 V 138 V 174 V 262 V Frequency range input 50 60 Hz 5 Hz auto sensing MANHATTAN Voltage regulation output 5 battery mode Frequency regulation output 50 60 Hz 1 Automatic voltage regulation AVR 120 and 220 models Waveftorm simulated sine wave Overload protection 110 warning and UPS shutoff after 10 seconds 120 UPS turnoff at once Battery capacity 12 V 5 Ah x 2 type sealed and lead acid Temperatures operation O to 40 storage 20 to 60 Operation relative humidity O to 95 non condensing e ED indicators Online Overload On Battery and Bad Battery Audible alarms Overload On Battery Low Battery Package Contents ine Interactive UPS 1000 VA 600 W Power Management Software CD Windows 98 SE Me 2000 XP compatible Cables RS232 6 ft 1 8 telephone RJ 11 6 ft 1 8 power cable 6 ft 1 8 e User manual gt A MANHATTAN WARRANTY INFORMATION Coverage For the original
3. D monitor at 85 VV Recharge 8 hours typical 12 hours maximum Transfer 4 ms typical 1O ms maximum Communications port 5232 120 RS232 220 V Telephone fax network ports RJ 11 RJ 45 1 in 1 out surge protected Nominal voltage input 100 V 110 V 120 V 220 V 230 V 240 V output 120 V 230 V Voltage range input 96 V 138 V 174 V 262 V Frequency range input 50 60 Hz 5 Hz auto sensing Voltage regulation output 5 battery mode Frequency regulation output 50 60 Hz 1 Automatic voltage regulation AVR 120 V and 220 V models Waveform simulated sine wave Overload protection 110 warning and UPS shutoff after 10 seconds 120 UPS turnoff at once Battery capacity 12 V 7 Ah type sealed and maintenance tree lead acid Temperatures operation O to 40 storage 20 to 60 4 MANHATTAN Operation relative humidity O to 95 non condensing LED indicators Online Overload On Battery and Bad Battery e Audible alarms Overload On Battery Low Battery Package Contents Line Interactive UPS 500 VA 300 W Power Management Software CD Windows 98 SE Me 2000 XP compatible e Cables RS232 6 ft 1 8 telephone RJ 11 ft 1 8 power cord 6 ft 1 8 e User manual Model 168175 e Outlets 5 NEMA 120 V 4 backup surge 1 surge only IEC 220 V backup surge Times Backup 5 minutes at full load 12 minutes at 50 load
4. LINE INTERACTIVE UNINTERRUPTIBLE POWER SUPPLY MODEL168120 168175 mm Thank you for purchasing the MANHATTAN Line Interactive Uninterruptible Power Supply Model 168120 or 168175 This uninterruptible power supply UPS is designed to keep computers and peripheral devices operating after a utility power failure that could result in component damage or loss of data Whenever the UPS is plugged in it maintains a full charge on its battery and serves to protect your equipment from utility generated surges and noise It also provides visual and audible indicators that alert you to utility line failures giving you ample time to save files and close operations Among the main features Advanced protection for and Macintosh systems against power outages sags surges and line noise Builtin microprocessor maintains proper charge provides consistent power output and helps extend battery lite Automatic voltage regulation AVR cold start capability and diagnostics 480 Joules telephone and network surge protection Fuse protection from overload and short circuit events e LED and audible alert system and power management software help monitor critical functions e 100 000 connected equipment guarantee US and Canada only Lifetime Warranty UPS Three year Warranty battery Package contents Line Interactive UPS Model 168120 500 VA 300 or Model 168175 1000 VA 600 W e UPS Monitor Software CD
5. e which equipment is to be left unprotected by the UPS Once the overload or short circuitry is released reset the input circuit breaker on the rear panel by pressing the button in Then re start the UPS Do not plug laser printers into this device as their power requirements are much greater than the capacity of the UPS Connection for Telephone Network Surge Suppression Connect a singledine telephone 10 Base T network cable into the telephone network surge protection sockets on the rear panel of the UPS The RJ 11 RJ 45 modular combination sockets accept all standard singleine telephone and 10 BaseT connections The cable coming from the telephone service or networked system is connected to the port marked IN the OUT port is connected to the equipment to be protected E MANHATTAN CONTROLS amp INDICATORS 6 1 On Off Test Button This button controls power to the UPS and its eem output receptacles Press and hold the button one to four seconds to switch on the UPS Press and hold the button two to three seconds when the utility power is normal and the UPS will simulate a utility outage and perform its selHest function It provides a convenient means of testing the UPS s battery Push the button during a utility failure when the UPS is off and the UPS will re start and provide power to its output receptacles During utility power outage the UPS will emit one beep every tive seconds Press and hold the b
6. es 6 8 Battery Backup amp Surge Protection Outlets These 120 V Models 168120 left 168175 right Output ports for 220 V models will vary in number and type See Specifications provide emergency battery backup power as well as surge protection 9 Input Circuit Breaker Fuse The UPS will the circuit breaker or blow the fuse when the loads exceed the UPS capacity The re settable button extends when tripped E MANHATTAN 10 Communications Port This connects the UPS to your computer via an RS232 serial cable UPS monitor software is included NOTE The UPS can work independently without an 5 232 connection 11 Telephone Network Surge Suppression The RJ 11 45 module connectors are used for single line telephone and 10 Base T surge protection NOTE This connection is not needed to use the UPS INDICATOR TABLE The UPS has both visible LED and audible alarm status indicators The LED numbers correspond to the Indicator images page 7 Overload On Line On Battery UPS Status ry LED LED LED Indicati Red 2 Yellow 3 Green 4 Green 5 Bad battery Xx On X X X AC mode X O 2 beeps e 10 second intervals DC mode X 2 beeps e 1 second intervals Low battery Constantly on Overload O0 L X oa NE NE 4MANHATTAN TROUBLESHOOTING Symptom Possible Cause The UPS will not turn UPS is not plugged into an AC on outlet and or is not tu
7. hat currently powers your computer equipment may be swapped with the supplied output cord Hence the swapped output line cord can be used instead as the input line cord for the UPS MANHATTAN Initial Battery Charging The UPS is shipped from the factory with its internal battery fully charged However the battery may lose some charge during shipping and storage The battery should be recharged before conducting the following test for proper operation and to ensure the UPS will provide expected run time The UPS automatically charges the battery whenever the UPS is plugged in the On Ott Test switch doesn t have to be turned on You can be sure that the battery is fully recharged if the UPS is left plugged in for at least eight hours Connecting Your Equipment to the UPS To ensure that your computer equipment will be protected during a utility failure and that you receive expected run time it is important that the total power needs of the equipment not exceed the capacity of the UPS The UPS will emit a loud tone and the yellow LED will illuminate to alert you of an overload Consult your dealer for the power requirements of your equipment Once you have determined that your equipment and the UPS are compatible plug your equipment into the rear panel output receptacles of the UPS Test for Proper Operation Push the On Off Test button to turn on your computer equipment The green NORMAL indicator on the front panel should be illuminated a
8. nd your equipment should operate normally To test the operation of the UPS simply unplug its input cord to simulate a utility blackout The UPS will immediately transfer your equipment loads to power derived from its internal battery During this time the UPS will emit two beeps once every 1O seconds to remind you that your equipment is operating from a 4 MANHATTAN source of power that is limited in duration Restore power to the UPS by plugging in the line cord Repeat this test four or five times to ensure proper operation Another way to test the operation of the UPS is to simply press and hold On Ott Test button for two seconds or more and then release it to run a selHest routine The UPS will immediately transfer your equipment to power derived from its internal battery and run a selHest See the next section if abnormal operation is encountered Overloads and Output Shorts If the total power requirement of your equipment is much greater than the capacity of the UPS the UPS rearpanel circuit breaker may trip 120 model 168175 and the 220 V versions have a fuse instead of a circuit breaker Once the breaker is tripped the UPS will attempt to operate the load using its internal power source The UPS will emit a loud tone before it shuts down and ceases to power your equipment The yellow LED will be illuminated and stay on to alert you of the overload until the UPS is started up again In this case turn off the UPS and decid
9. ownouts and line noise When AC power is present and the UPS is turned on it continues to charge the battery and provide power to the equipment directly from the AC line The battery can provide stable power to complete your work save data and safely shut down your system when the utility power has failed The UPS is simple to operate and install Following are the steps for connecting equipment to the UPS 4MANHATTAN Conditions Do not operate the UPS in an environment where the ambient temperature is outside the limits given in the Specifications section of this manual Connection to the Utility Power Plug the UPS into an electrical outlet Do not plug it into an outlet that already uses a heavy electric load e g an air conditioner refrigerator or laser printer 120 V AC Version The 120 V AC version of the MANIHATTAN Line Interactive UPS is furnished with a line cord terminated with a standard NEMA 5 15P three pronged plug The UPS must be plugged into a two pole three wire grounding receptacle an extension cord must be used use a three wire grounding type rated at least 8 Amps Plug the UPS into a two pole three wire grounded receptacle only Avoid using extension cords and adapter plugs 220 V AC Version The 220 V AC version is furnished with one output power cord for connection to computer equipment having IEC 320 male appliance couplers at their input In most cases this will not be a problem as the input cord t
10. purchaser of this MANHATTAN Uninterruptible Power Supply residing in the United States or Canada the device itself features a litetime warranty covering material and workmanship with a three year warranty on the battery Should the UPS fail it will either be repaired or replaced manufacturer s option Should UL CSA or CEisted electronic equipment connected to the MANHATTAN Uninterruptible Power Supply be damaged by power or phone line transients such as spikes or surges the manufacturer has the option of repairing or replacing the damaged equipment or keeping the damaged equipment and paying fair market value for it not to exceed a total of 100 000 This warranty does not cover a damage caused by improper installation repairs servicing or alterations b damage due to the improper packing or shipping of items returned to the manufacturer c damage to electronic equipment that is not UC UL CSA or CElisted d damage to UL CSA or CElisted equipment not caused by power or phone line transients such as spikes or surges damage caused by a failure fo use properly wired and grounded electrical outlets telephone service and if applicable cable TV service f damage caused by a failure to install primary protection devices for power and telephone service equipment g damage caused by cable TV transients or damage caused during any use of this device for which it was not intended Note Some states do not allow the excl
11. rned on Output short overload shutdown Computer interface or accessory problem All LEDs are lit and Internal UPS system fault the UPS is emitting a constant tone The UPS doesn t provide The battery is not fully charged expected run time The battery is old or bad Other LEDs are off but The UPS is shut down and the the Replace battery LED battery is discharged due to an is blinking No alarm is extended power outage sounding but the UPS is not operating Action to Take Plug the UPS in and turn it on If power is still not present make sure the circuit breaker on your building is not accidentally turned oft Reduce the load and reset the circuit breaker or replace the blown fuse if so designed Disconnect the interface then press the computer reset button Return the UPS for service Remove all connected equipment from the UPS and charge the battery for at least 8 hours While the battery is charging turn the UPS off to prevent any unnecessary discharging Return for service None The UPS will return to normal operation when the power is restored and the battery regains a sufficient charge 2 2 MANHATTAN SPECIFICATIONS Available in 120 V NEMA and 220 V IEC models Model 168120 e Outlets NEMA 120 V 3 backup surge only 2 IEC 220 V 2 backup surge Times Backup 3 minutes at full load 10 minutes at 50 load minutes at varying loads typical with PC and 15 LC
12. usion or limitation of incidental or consequential damages which means the above may not apply This warranty gives you specific legal rights You may also have other rights which vary state fo state Implied Warranty Implied warranties including the implied warranty of merchantability and the implied warranty of fitness for MANHATTAN a purpose end when the original purchaser no longer owns the product and three years from the date of purchase for the battery Note Some states do not allow time limitations on implied warranties which means the above limitations may not apply MANHATTAN aA 7 MANHATTAN BRINGING COMPUTERS IO LIFE MANHATTAN offers a complete line of PC Components Peripherals Cables and Accessories Ask your local computer dealer for more information or visit us online at www manhattan products com Copyright MANHATTAN All products mentioned are trademarks or registered trademarks of their respective owners
13. utton for two seconds to silence the beep 2 Replace Battery LED The LED lights when the UPS detects that the battery needs fo be replaced soon Charge the UPS at least four hours IF the LED lights again after charging the battery might need replacing 3 Overload LED During an overload operation the UPS will emit a loud tone and this LED will come on See Troubleshooting to recover the UPS 459 V Model 168120 shown Indicators are similar for 220 V version and both versions 4 On line LED During normal operation this indicator always stays S Wedel 168175 When the automatic voltage regulator is in operation this LED blinks 5 On battery LED In on battery operation the on battery LED illuminates and the UPS will sound two beeps once every ten seconds The UPS will emit a steady tone when the battery reserve runs low until either the AC returns or the UPS shuts down from battery exhaustion 4 MANHATTAN 6 AC Power Cord Complete the ao M _ necessary power connections For 11 Model 168120 120 V use an existing NEMAtype PC power cord to connect the PC to the UPS Use the included NEMAtype power cord to connect the UPS to the power source For 220 V models use the included IECtype power cord to connect the PC to the UPS Use one of the existing PC power cords to connect the UPS to the powersource 7 Surge Protection Bypass Outlets These protect against surges and spik
Download Pdf Manuals
Related Search