Peerless ACC840
Contents
1. the false ceiling Also be sure to use the rubber bumper B provided 1of4 ISSUED 12 14 01 SHEET 055 9068 3 11 10 04 Visit the Peerless Web Site at www peerlessindustries com For customer service call 1 800 729 0307 or 708 865 8870 D Attach four rubber bumpers B to anti vibration mount A as shown below oy v l l l l B l l Co l A Use stud finder to locate stud centers Use anti vibration mount A as a template to mark slot centers on stud centers Ceiling Wood stud A _ o XQ TOP VIEW Visit the Peerless Web Site at www peerlessindustries com For customer service call 1 800 729 0307 or 708 865 8870 5 32 4 mm dia holes 2 1 2 65 mm deep Attach anti vibration mount A using two 14 x 2 5 6 mm x 65 mm wood screws D and two plastic washers E Note Make sure rubber bumpers B are firmly in place before attaching to ceiling FOR WOOD JOIST FINISHED CEILING EXPOSED WOOD JOISTS OR WOOD BEAM CEILING ONLY drill four A WARNING ae ee Tighten wood screws so that anti vibration mount is lt gt Ceiling firmly attached but do not overtighten Overtightening m a can damage the screws greatly reducing their holding power and decrease the anti vibrational effectiveness Tighten to 30 40 in Ib 3 4 4 5 N M maximum torque e Make sure that mounting screws are anchored into the center of the joist The use of an edge to2. Installation and Assembly Vibration Absorber Ceiling Mount for Structural Model Ceiling ACC 840 IMPORTANT Read entire instruction sheet before you start installation and assembly Installer must verify that the ceiling will safely support Before you start check the parts list below to four times the combined weight of all attached equip make sure all of the parts shown are included ment and hardware Parts List Description Part Number 055 0004 590 1124 590 1123 5S81 015 C03 540 9439 530 9401 520 1063 520 9250 anti vibration mount rubber bumper plastic finishing caps 14 x 2 5 wood screw 26 x 7x 062 plastic washer rubber grommet M5 x 8 x 10 mm socket pin screw M5 x 8 x 10 mm phillips screw IIO Tn mojoj ninin a Note Actual parts may appear slightly different than illustrated e If mounting to Unistrut purchase model ACC 845 Model ACC 840 should be mounted to wood only If the anti vibration mount is altered in any way it may not be as effective or effective at all in controlling vibration In addition be certain that no part of the system including any extension column that might be used comes in contact with the vibrating surface If mounting through a drop ceiling be sure to cut a large enough hole in the ceiling tile as to avoid contact with the extension column If using an escutcheon ring be sure it does not come in contact with
3. edge stud finder is highly recommended When attaching anti vibration mount A to flush mount tube or extension column both tube and column are sold separately tighten at least four complete turns ending with one of the small threaded holes aligned with slot in the end of flush mount tube or extension column Insert and tighten one M5 screw H to lock tube position shown below on right side Note For security the M5 phillips screw H can be replaced with M5 socket pin screws G flush mount tube or extension column sold separately 3 of 4 ISSUED 12 14 01 SHEET 055 9068 3 11 10 04 Visit the Peerless Web Site at www peerlessindustries com For customer service call 1 800 729 0307 or 708 865 8870 When attaching anti vibration mount A to flush mount tube or extension column both tube and column are sold separately tighten at least four complete turns ending with one of the small threaded holes aligned with slot in the end of flush mount tube or extension column Insert and tighten one M5 screw H to lock tube position shown below on right side Note For security the M5 philips screw H can be replaced with M5 socket pin screws G flush mount tube or extension column sold sparately O Place one finishing cap C on each end of OPTIONAL Place grommet F on anti anti vibration mount A vibration mount A and place one finishing cap C on other end of anti vibration mount A Route cords throu
4. gh extension column and out cord management holes in anti vibration mount A Note If using Vector Pro projector mounts you will need accessory ACC 800 to route cords through column 4of4 ISSUED 12 14 01 SHEET 055 9068 3 11 10 04 Visit the Peerless Web Site at www peerlessindustries com For customer service call 1 800 729 0307 or 708 865 8870 2004 Peerless Industries Inc All rights reserved Peerless is a registered trademark of Peerless Industries Inc Unistrut is a registered trademark of Peerless Industries Inc
Download Pdf Manuals
Related Search