Panasonic WV-Q175E
Contents
1. Panasonic Operating Instructions Ceiling Mount Bracket vano WV Q175 WV Q175E Before attempting to connect or operate this product please read these instructions carefully and save this manual for future use The model number is abbreviated in some descriptions in this manual CONTENTS ENE O e ests eateries cect REA 3 Sele 3 Major operating controls and their fUNCtIONS ooo eee eee ee ee eee ee eee 5 Installations 3 scivec cei E E E EE ETE eis ee A ee 5 SPSCHICANOMS cess 0 usages ivecsanen ives dessus R E coatacieiesaustesshescenaes tessa a 10 Standard2acceSSones sascs cy scecesaciscvechs sued caeetees E E e E E 11 Preface This ceiling embedded bracket is exclusively designed to mount a color CCTV camera or a net work camera Refer to the catalog or the operating instructions of the camera for supported cameras This bracket is an embedded type to reduce the exposed portion of the camera body Precautions Refer installation work to the dealer Installation work requires technique and experiences Failure to observe this may cause fire electric shock injury or damage to the product e Be sure to consult the dealer Use only the specified camera Failure to observe this may cause a fall of an inappropriate camera resulting in injury or accidents e Refer to the catalog or the operating instructions of the camera for supported cameras Select an installation area If a selected area is too weak to sup2. e camera together 1 Put Template A accessory against the ceiling and make a hole Make 4 holes of 12 mm 1 2 inches in diameter Note Make these holes so that the Panasonic logo is directed to the Ceiling face desired side Remove the center part from the tem plate Make a hole of 180 mm 7 1 16 inches in diameter 2180 mm The ceiling holes are 7 1 16 inches shown in the drawing at right gt Template A 912 mm 1 2 inches 4 positions Important Make a hole precisely When the opened hole is bigger or deformed too much the ceiling mount bracket cannot be stuck on the ceiling board securely 2 Install two anchor bolts locally procured M10 recommended into the concrete ceil ing Install an anchor bolt in the center of the hole made in the step 1 Determine the anchor bolt length by use of Template B accessory Use Template B to decide the nut position and fix it Mount the nut so that the dis tance between the bottom sur faces of the nut and ceiling is adjusted to 134 mm 5 1 4 Install the anchor bolt in the center inches 1 of the hole 2nd Anchor bolt 1st Anchor bolt locally procured locally procured yP Nut locally procured Anchor bolt Determine the anchor bolt length 134 mm Template B 5 1 4 inches m Ceiling board Note If there is already an anchor bolt installed the anchor bolt can be used as a 2nd anchor bolt Mak
3. e sure that the distance between the 1st and 2nd anchor bolts is 1 000 mm 3 28 feet or less before use 3 Mount the safety wire angle accesso ry on the 2nd anchor bolt and con nect the safety wire accessory to the Anchor bolt lt gt Upper side Mark angle Insert Bend Disconnect the safety wire from the safe 0 Disconnect ha ty wire angle Engage the face marked with the anchor bolt N Bend the face marked Connect the safety wire to the safety wire Safety wire angle again ats ta side Mark Note To use the anchor bolt that was already installed the use of 2 spacer nuts locally procured is helpful Spacer nuts Spacer nuts locally procured Safety wire angle Safety wire Existing anchor bolt WLLL LLL 4 Connect this mount bracket to the tip of the safety wire Roof space Insert the mount bracket into the hole Mount bracket 5 Insert the 1st anchor bolt into the mounting hole of the mount bracket Mounting hole Ceiling board fixing screw Direction of the Panasonic logo Note The Panasonic logo will be direct ed to the ceiling board fixing screw which is secured on the side described in the illustration When inserting the mount bracket into the ceiling fit the bracket in the 4 mounting holes of 12 mm 1 2 inch es in diameter on the ceiling 6 Secure the mount bracket to the ceil ing board with the ceilin
4. following locations e Locations where it may get wet from rain or water splash not only outdoor e Locations where a chemical agent is used such as a swimming pool e Locations subject to steam and oil smoke such as a kitchen e Locations where radiation or x ray emissions are produced e Locations where it may be damaged by briny air such as seashores e Locations where the temperature is not within the ambient temperature of the camera in use and this product e Locations subject to vibrations This product is not designed for on vehicle use e Locations where the temperature may rapidly change such as the peripheral areas of the air outlets of air conditioners or doors facing outside In case of installing the cam era in such locations the dome cover may become foggy or condensation may be caused on the cover e The screws and bolts must be tightened with an appropriate tightening torque according to the material and strength of the installation area After tightening the screws or bolts per form visual check to ensure tightening is enough and there is no backlash Major operating controls and their functions Roof space Safety wire angle Accessory IO Safety wire Accessory Read the operating instructions of the camera as well Installations Be sure to read Precautions before installation It is recommended to read them while referring the operating instructions of th
5. g board fixing screws 4 positions Turning the ceiling board fixing screws clockwise provides ceiling board tighten ing between the bottom of the mount bracket and ceiling board fixing bracket resulting in mount bracket securing Recommended tightening torque 0 78 N m 0 58 Ibf ft Important When securing this bracket on the ceiling make sure that the four ceiling board fixing brackets are open as shown in the following fig ure 1st anchor bolt Double nuts locally HA3 U procured Ceiling board fixing screw Soon Ceiling board ch fixing bracket Ceiling board Turn clockwise Important When the ceiling board is the plasterboard make sure that no crack was made on the ceiling board by clamping 7 Use double nuts locally procured to secure the mount bracket after insert ing the 1st anchor bolt 8 Follow the procedure according to the Se model of the camera to be installed SE BZ Protrusion T S camera PA L mounting hole lt Installing WV CF504 gt Mount the camera attachment supplied with the camera to this bracket Fixi ixing screw hole Attachment Use 4 fixing screws accessory to Single rib mounting hook secure the camera attachment firmly as shown in the drawing Recommended tightening torque 0 78 Note When the camera is secured the N m 0 58 Ibf ft camera attachment protr
6. port the total weight a fall of the product may occur resulting in injury e Installation work shall be started after sufficient reinforcement e The installation area shall have 210 mm 8 1 4 inches or more space behind the ceil ing e The thickness of the ceiling board for installation can range from 9 mm to 40 mm 3 8 inches to 1 9 16 inches 210 mm 8 1 4 inches or more SS E Ceiling board from 9 mm to 40 mm 3 8 inches to 1 9 16 inches Avoid installing this bracket in the locations where salt damage occurs or corrosive gas is produced Otherwise the mounting portions will deteriorate and accidents such as a fall of the camera may occur The screws and fixation mechanisms shall be tightened securely Failure to observe this may cause a fall of the camera resulting in injury Periodic inspections shall be conducted Rust on the metal parts or screws may cause a fall of the product resulting in injury e Consult the dealer for the inspections Do not rub the edges of metal parts with your hand Failure to observe this may cause injury e Make sure that the installation area is strong enough to hold the total weight of the camera assembly before installation e The camera and the ceiling mount bracket should be fixed using the provided fixing screws and make sure that the both of them are fixed firmly e When the ceiling mount bracket is not necessary anymore remove from the ceiling e Avoid installing in the
7. usion is aligned with the camera fixing screw hole and the double rib on the camera Secure the camera to the camera attachment with the camera fixing screw Recommended tightening torque 0 78 N m 0 58 Ibf ft Mount bracket Camera attachment 4 La Fixing screws Connect the camera cables Mount the camera a Align the single rib on the camera Adjust the camera with the protrusion on the camera Refer to the operating instructions of the attachment camera b Engage the camera s attachment mounting hooks with the mounting holes on the camera attachment and then rotate the camera in the direction of the arrow to secure the camera to the camera attachment without any backlash 9 Mount the decorative cover on this mount bracket e Mount the decorative cover on the cam era mounting plate with engaging the projections of the decorative cover with the hooks for the decorative cover e Turn the decorative cover clockwise until the cover clicks while pressing the cover upward to lock the cover Hooks for the decorative Note Mount the decorative cover on the mount bracket so that the Panasonic logo is directed to the side which was determined when making the mounting holes 10 Specifications Ambient temperature 10 C to 50 C 14 F to 122 F Dimensions 204 4 mm 8 1 16 inches in diameter x 143 4 mm 5 5 8 inches in height Mass Appro
8. x 700 g 1 55 Ibs Finish Main body Metal Decorative cover ABS plastic Standard accessories Operating Instructions this book e 1 pc The following are for installation Safety WING saz a r 2 1 Tada baan taie 1 pc Safety wire angle ieee 1 pc Tempat A inime denies edi tenths elit 1 pc Template B yenmenin ee e 1 pc Fixing screw M4 x 8 sene 5 pcs incl 1 spare screw For U S and Canada Panasonic System Networks Company of America Unit of Panasonic Corporation of North America www panasonic com business For customer support call 1 800 528 6747 Three Panasonic Way Secaucus New Jersey 07094 U S A Panasonic Canada Inc 5770 Ambler Drive Mississauga Ontario L4W 2T3 Canada 905 624 5010 www panasonic ca Panasonic System Networks Co Ltd 2011 Ns0211 1061 For Europe and other countries Panasonic Corporation http panasonic net Importer s name and address to follow EU rules Panasonic Testing Centre Panasonic Marketing Europe GmbH Winsbergring 15 22525 Hamburg F R Germany 3TRO06878BZA Printed in China
Download Pdf Manuals
Related Search