AEG F78400VI0P
Contents
1. shows an alarm code e Q The appliance does not fill with water Problem Possible cause e if The anti flood device is on WARNING Deactivate the appliance before you make the checks Possible solution The programme does not start The mains plug is not con nected in the mains socket Connect the mains plug The fuse in the fuse box is damaged The appliance door is open Close the appliance door Replace the fuse The delay start is set Cancel the delay start or wait for the end of the countdown The appliance does not fill with water The water tap is closed The water pressure is too low Open the water tap Contact your local water au thority The water tap is clogged or there is limescale on it Clean the water tap The filter in the water inlet hose is clogged The water inlet hose has a kink or a bend Clean the filter Make sure that the position of the hose is correct The anti flood device is on There are water leakages in the appliance Close the water tap and contact Service The appliance does not drain the water After the checks are completed acti The sink spigot is clogged The water drain hose has a kink or a bend Clean the sink spigot Make sure that the position of the hose is correct If the problem occurs again contact vate the appliance The programme continues from the point2. 10 43 50 76 90 7 6 9 0 53 63 21 9 37 42 65 75 6 5 7 5 46 52 21 8 29 36 51 64 5 1 6 4 36 45 21 7 23 28 40 50 4 0 5 0 28 35 21 6 19 22 33 39 33 39 23 27 21 51 15 18 26 32 2 6 3 2 18 22 1 11 14 19 25 19 25 13 17 1 4 10 7 18 0 7 1 8 5 12 lt 4 lt 7 lt 0 7 ES 12 12 1 Factory position 2 Do not use salt at this level 12 Manual adjustment Turn the water hardness dial to the po sition 1 or 2 Electronic adjustment 1 2 FILLING THE SALT CONTAINER Press the on off button to activate the appliance Make sure that the appliance is in setting mode Refer to SETTING AND STARTING A PROGRAMME Press and hold buttons 4 and 5 at the same time until the indicators of buttons 3 4 and 5 flash Press button 3 e The indicators of buttons 4 and 5 go off e The indicator of button 3 contin ues to flash e The acoustic signals operate Ex ample five intermittent acoustic signals level 5 e The display shows the setting of the water softener Example 5 level 5 Press button 3 again and again to change the setting Deactivate the appliance to confirm IN CAUTION Only use dishwasher salt Other products can cause damage to the appliance Water and salt can come out from the salt container when you fill it Risk of corrosion To prevent it after you fill the salt cont
3. competent per son e Remove all the packaging e Do not install or use a damaged ap pliance e Do not install or use the appliance where the temperature is less than 0 jes e Obey the installation instruction sup plied with the appliance e Make sure that the appliance is in stalled below and adjacent to safe structures Water connection e Make sure not to cause damage to the water hoses e Before you connect the appliance to new pipes or pipes not used for a long time let the water flow until it is clean e The first time you use the appliance make sure that there is no leakage WARNING Dangerous voltage The water inlet hose has a safety valve and a sheath with an inner mains cable e If the water inlet hose is damaged immediately disconnect the mains plug from the mains socket Contact Service to replace the water inlet hose Electrical connection WARNING Risk of fire and electrical shock e The appliance must be earthed e Make sure that the electrical informa tion on the rating plate agrees with the power supply If not contact an electrician e Always use a correctly installed shockproof socket e Do not use multi plug adapters and extension cables There is a risk of fire e Make sure not to cause damage to the mains plug and to the mains ca ble Contact Service or an electrician to change a damaged mains cable Connect the mains plug to the mains socket
4. of interrup tion Service If the display shows other alarm codes contact Service ENGLISH 19 THE WASHING RESULTS AND DRYING RESULTS ARE NOT SATISFACTORY Problem The dishes are not clean Possible cause The filters are clogged The filters are not correctly assembled and installed Possible solution Clean the filters Make sure that the filters are correctly assembled and in stalled The spray arms are clog ged Remove remaining soil with a thin pointed object The programme was not applicable for the type of load and soil Make sure that the pro gramme is applicable for the type of load and soil Incorrect position of the items in the baskets Water could not wash all items Make sure that the position of the items in the baskets is correct and that the water can easily wash all items Limescale particles on the dishes Whitish streaks and stains or bluish lay ers on glasses and dishes The spray arms could not turn freely The quantity of detergent was not sufficient There was no detergent in the detergent dispenser The salt container is empty The set level of the water softener is incorrect The cap of the salt contain er is loose The released quantity of rinse aid is too much Make sure that the position of the items in the baskets is correct and does not cause the blockage of the spray arms Make sure that you add the correct q
5. only atthe end of the installa tion Make sure that there is access to the mains plug after the installa tion Do not pull the mains cable to dis connect the appliance Always pull the mains plug Only for UK and Ireland The appli ance has a 13 amp mains plug If it is necessary to change the fuse in the mains plug use a 13 amp ASTA BS 1362 fuse USE WARNING Risk of injury Use this appliance in a household en vironment Do not change the specification of this appliance Put knives and cutlery with sharp points in the cutlery basket with the points down or in a horizontal posi tion Do not keep the appliance door open without supervision to prevent to fall on it Do not sit or stand on the open door Dishwasher detergents are danger ous Obey the safety instructions on the detergent packaging ENGLISH 5 e Do not drink and play with the water in the appliance e Do not remove the dishes from the appliance until the programme is completed There can be detergent on the dishes WARNING Risk of electrical shock fire or burns Do not put flammable products or items that are wet with flammable products in near or on the appliance e Do not use water spray and steam to clean the appliance e The appliance can release hot steam if you open the door while a pro gramme operates DISPOSAL WARNING Risk of injury or suffocation e Disconnect the appliance from the mains sup
6. FAVORIT 78400 VI DISHWASHER USER MANUAL 2 CONTENTS 4 SAFETY INFORMATION 6 PRODUCT DESCRIPTION 7 CONTROL PANEL 8 PROGRAMMES 10 OPTIONS 11 BEFORE FIRST USE 14 DAILY USE 17 CARE AND CLEANING 18 TROUBLESHOOTING 20 TECHNICAL INFORMATION ENVIRONMENT CONCERNS a Recycle the materials with the symbol CP Put the packaging in applicable containers to recycle it Help protect the environment and human health and to recycle waste of electrical and electronic appliances Do not dispose appliances marked with the symbol amp with the household waste Return the product to your local recycling facility or contact your municipal office VISIT OUR WEBSITE FOR Products Brochures User manuals Trouble shooter Service information www aeg com LEGEND A Warning Important Safety information General information and tips amp Environmental information Subject to change without notice ENGLISH 3 FOR PERFECT RESULTS Thank you for choosing this AEG product We have created it to give you impeccable performance for many years with innovative technologies that help make life simpler features you might not find on ordinary appliances Please spend a few minutes reading to get the very best from it ACCESSORIES AND CONSUMABLES In the AEG webshop you ll find everything you need to keep all your AEG appliances looking spotless and working perfectly Along with a wide range of accessories desig
7. ainer start a programme Turn the cap counterclockwise and open the salt container Put 1 litre of water in the salt con tainer only for the first time Fill the salt container with dish washer salt Remove the salt around the open ing of the salt container Turn the cap clockwise to close the salt container FILLING THE RINSE AID DISPENSER ENGLISH 13 CAUTION Only use rinse aid for dishwash ers Other products can cause damage to the appliance The rinse aid during the last rinsing phase helps to dry the dishes without streaks and stains Press the release button D to open the lid C Fill the rinse aid dispenser A no more than the mark max Remove the spilled rinse aid with an absorbent cloth to prevent too much foam Close the lid Make sure that the release button locks into position You can turn the selector of the released quantity B between position 1 lowest quantity and position 4 highest quantity DAILY USE 1 Open the water tap 2 Press the on off button to activate the appliance Make sure that the appliance is in setting mode Refer to SETTING AND STARTING A PROGRAMME e If the salt indicator is on fill the salt container e If the rinse aid indicator is on fill the rinse aid dispenser Load the baskets Add the detergent 5 Set and start the correct pro gramme for the type of load and soil LOADING THE BASKETS 1 Re
8. arts Opening the door while the appliance operates If you open the door the appliance stops When you close the door the appliance continues from the point of interruption Cancelling the delay start while the countdown operates 1 Open the appliance door 2 Press the delay button again and again until the display shows the programme number 3 Close the appliance door The pro gramme starts Cancelling the programme Press RESET until e The display shows two horizontal sta tus bars i Make sure that there is deter gent in the detergent dispenser before you start a new pro gramme At the end of the programme When the programme is completed an intermittent acoustic signal operates 1 Open the appliance door e The end indicator is on e The display shows 0 2 Press the on off button to deacti vate the appliance Close the water tap 9 If you do not press the on off button the AUTO OFF device automatically deactivates the appliance after some minutes This helps to decrease the ener gy consumption w e For better drying results keep the appliance door ajar for some mi nutes e Let the dishes become cold before you remove them from the appli ance Hot dishes can be easily dam aged e First remove the items from the lower basket then from the upper basket i There can be water on the sides and on the door of the appli ance Stainless steel becomes cool more quick
9. e to confirm BEFORE FIRST USE 1 mW ID 1 Make sure that the set level of the water softener agrees with the water hardness in your area If not adjust the water softener Contact your lo cal water authority to know the wa ter hardness in your area Fill the salt container Fill the rinse aid dispenser Open the water tap Processing residues can stay in the appliance Start a programme to re move them Do not use detergent and do not load the baskets If you use the combi detergent tablets activate the multitab function These tablets contain ENGLISH 11 ADJUSTING THE WATER SOFTENER Hard water contains a high quantity of minerals that can cause damage to the appliance and bad washing results The water softener neutralises these miner als The dishwasher salt keeps the water softener clean and in good conditions Refer to the table to adjust the water softener to the right level It makes sure that the water softener uses the correct quantity of dishwasher salt and water You must adjust the water soft ener manually and electronical ly detergent rinse aid and other added agents Be sure that these tablets are applicable to the water hardness in your area Refer to the instructions on the packaging of the products Water hardness Weier softener adjustment German French mmol l Clarke Manual Elec degrees degrees degrees tronic dH fH 51 70 91 125 91 1285 64 88 21
10. es Programme 1 Duration min Energy kWh Water I 1 80 140 wen 8 14 AUTO 45 70 2 130 150 1 1 1 2 10 11 PRO 70 3 180 200 0 9 1 0 8 9 Extra SILENT 50 4 30 0 8 7 Quick 30MIN 60 5 170 190 0 7 0 8 8 9 ECO 50 6 40 50 0 8 0 9 8 9 Quick 50MIN 554 7 70 80 0 6 0 7 9 10 Y 45 8 10 0 01 3 LIS A YA 1 The water pressure and temperature the variations of the mains supply the options and the quantity of dishes can change the programme duration and the consumption values 10 OPTIONS MULTITAB FUNCTION Activate this function only when you use the combi detergent tablets This function deactivates the flow of rinse aid and salt The related indicators are off The programme duration can increase Activating the multitab function 1 Activate or deactivate the multi tab function before the start of a programme You cannot acti vate or deactivate this function when a programme operates 1 Press the on off button to activate the appliance 2 Make sure that the appliance is in setting mode Refer to SETTING AND STARTING A PROGRAMME 3 Press the multitab button the multi tab indicator comes on i The function stays on until you deactivate it Press the multitab button the multitab indicator goes off If you stop to use the combi detergent tablets before you start to use separately detergent rinse aid and dishwasher salt do these steps 1 Deactivate
11. fer to the supplied leaflet with examples of the load of the bas kets e Only use the appliance to wash items that are dishwasher safe e Do not put in the appliance items made of wood horn aluminium pewter and copper Do not put in the appliance items that can absorb water sponges household cloths Remove remaining food from the items Make soft the remaining burned food on the items Put hollow items cups glasses and pans with the opening down Make sure that cutlery and dishes do not bond together Mix spoons with other cutlery Make sure that glasses do not touch other glasses Put small items in the cutlery basket Put light items in the upper basket Make sure that the items do not move Make sure that the spray arms can move freely before you start a pro gramme USING THE DETERGENT ENGLISH 15 A B W f CAUTION Use only detergents for dish washers Press the release button B to open the lid C 2 Put the detergent in the compart ment A 3 Ifthe programme has a prewash phase put a small quantity of de tergent on the inner part of the ap pliance door 4 Ifyou use detergent tablets put the tablet in the compartment A 5 Close the lid Make sure that the release button locks into position Do not use more than the cor rect quantity of detergent Refer to the instructions on the deter gent packaging Detergent tablets d
12. lets Activating the rinse aid e The indicator of button 4 contin dispenser with the multitab ues to flash function activated e The display shows the setting of the rinse aid dispenser 1 Press the on off button to activate the appliance Dd en 2 Make sure that the appliance is in id On setting mode Refer to SETTING ooo AND STARTING A PROGRAMME 5 Press button 4 to change the set ting 3 Press and hold buttons 4 and 5 at the same time until the indicators of Deactivate the appliance to confirm buttons 3 4 and 5 flash Adjust the released quantity of rinse 4 Press button 4 aid e The indicators of buttons 3 and 5 go off TECHNICAL INFORMATION Fill the rinse aid dispenser Dimensions Electrical connection Water supply pressure Width Height Depth mm Refer to the rating plate Min max bar MPa 446 818 898 550 0 5 0 05 8 0 8 ENGLISH 21 Water supply Cold water or hot water max 60 C 9 Capacity Place settings 1 Connect the water inlet hose to a water tap with a 3 4 thread 2 If the hot water comes from alternative sources of energy e g solar panels aeolian energy use the hot water supply to decrease energy consumption 22 ENGLISH 23 www aeg com shop 117929050 A 192011 ce
13. ly than the dishes ENGLISH 17 CARE AND CLEANING MN WARNING i Dirty filters and clogged spray arms decrease the washing re sults Make a check regularly and if necessary clean them Before maintenance deactivate the ap pliance and disconnect the mains plug from the mains socket CLEANING THE FILTERS 1 Turn the filter A counter clockwise and remove it 2 To disassemble the filter A pull apart A1 and A2 Remove the filter B Wash the filters with water 5 Put the filter B to its initial position Make sure that it assembles correctly under the two guides C 6 Assemble the filter A and put it into position in filter B Turn it clockwise until it locks i An incorrect position of the filters can cause bad washing results and dam age to the appliance Pw CLEANING THE SPRAY ARMS Only use neutral detergents Do not use abrasive products abrasive clean Do not remove the spray arms ing pads or solvents If the holes in the spray arms are clog ged remove remaining parts of soil with a thin pointed object EXTERNAL CLEANING Clean the appliance with a moist soft cloth 18 TROUBLESHOOTING The appliance does not start or it stops during operation First try to find a solution to the prob lem refer to the table If not contact Service e cf The appliance does not drain the water With some problems the display
14. ned and built to the high quality standards you would expect from specialist cookware to cutlery baskets from bottle holders to delicate laundry bags Visit the webshop at www aeg com shop CUSTOMER CARE AND SERVICE We recommend the use of original spare parts When contacting Service ensure that you have the following data available The information can be found on the rating plate Model PNC Serial Number AN SAFETY INFORMATION Before the installation and use ofthe appliance carefully read the supplied instructions The manufacturer is not re sponsible if an incorrect installation and use causes injuries and damages Al ways keep the instructions with the ap pliance for future reference CHILDREN AND VULNERABLE PEOPLE SAFETY WARNING Risk of suffocation injury or per manent disability e Do not let persons children inclu ded with reduced physical sensory reduced mental functions or lack of experience and knowledge use the appliance They must have supervi sion or instruction for the operation of the appliance by a person who is responsible for their safety Do not let children play with the appliance e Keep all packaging away from chil dren There is the risk of suffocation and injury e Keep all detergents away from chil dren e Keep children and pets away from the appliance door when it is open INSTALLATION WARNING This appliance must be installed by a qualified or
15. o not fully dissolve with short programmes and detergent residues can stay on the dishes We recommend that you use detergent tablets with long pro grammes SETTING AND STARTING A PROGRAMME Setting mode The appliance must be in setting mode to accept some operations The appliance is in setting mode when after the activation e The display shows two horizontal sta tus bars If the control panel shows other condi tions press RESET until the appliance is in setting mode Starting a programme without delay start 1 Open the water tap 2 Press the on off button to activate the appliance Make sure that the appliance is in setting mode 3 Set the programme e The related programme number flashes in the display 4 If you want you can set the options 5 Close the appliance door The pro gramme starts e If you open the door the display shows the programme duration that decreases with steps of 1 mi nute Starting a programme with delay start 1 Set the programme 2 Press the delay button again and again until the display shows the de 16 lay time you want to set from 1 to 24 hours e The delay time flashes in the dis play e The delay indicator is on 3 Close the appliance door The countdown starts e If you open the door the display shows the countdown of the de lay start that decreases with steps of 1 hour e When the countdown is completed the programme st
16. ply e Cut off the mains cable and dispose of it e Remove the door catch to prevent children and pets to get closed in the appliance 6 PRODUCT DESCRIPTION Upper spray arm Upper basket A Lower spray arm Filters LIGHT BEAM EJ Rating plate e When a programme operates a red Saltcontainet light beam shows on the floor below 5 the appliance door When the pro 6 Water hardness dial gramme is completed the red light Rinse aid dispenser changes to a green light e When the appliance has a malfunc El Detergent dispenser tion the red light beam flashes EJ Cutlery basket Lower basket ENGLISH CONTROL PANEL 08 O OFF LJ ey I la ee Cel lt 5 L i 7 On off button a KO PLUS button A Display Multitab button Delay button 8 RESET button 4 Programme button down El Indicators Programme button up Indicators 3 Salt indicator This indicator is off while the programme operates Esa Rinse aid indicator This indicator is off while the programme op erates gt End indicator 8 PROGRAMMES Programme Type of soil Programme phases Options Type of load 1 All Prewash KO PLUS AUTO 1 Crockery cutlery Wash 45 C or 70 C 45 70 pots and pans Rinses Dry 2 Heavy soil Prewash OKO PLUS PRO Crockery cutlery Wash 70 C 70 2 pots and pans Rinses Dry 3 Normal soil Prewash Extra Crockery and Wash 50 C SILENT 3 cutlery Rinses 50 Dr
17. the multitab function 2 Set the water softener to the high est level 3 Make sure that the salt container and the rinse aid dispenser are full 4 Start the shortest programme with a rinsing phase without detergent and without dishes 5 Adjust the water softener to the wa ter hardness in your area 6 Adjust the released quantity of rinse aid OKO PLUS This function decreases the tempera ture in the drying phase The energy consumption decreases by 25 The dishes can be wet at the end of the programme We recommend that you keep the door ajar and let the dishes dry ACOUSTIC SIGNALS The acoustic signals operate in these conditions e The programme is completed e The level of the water softener is ad justed electronically e The appliance has a malfunction i Factory setting on You can de activate the acoustic signals Deactivating the acoustic signals 1 Press the on off button to activate the appliance 2 Make sure that the appliance is in setting mode Refer to SETTING AND STARTING A PROGRAMME 3 Press and hold buttons 4 and 5 at the same time until the indicators of buttons 3 4 and 5 flash 4 Press button 5 e The indicators of buttons 3 and 4 go off e The indicator of button 5 contin ues to flash e The display shows the setting of the acoustic signals lb On ob Off 5 Press button 5 to change the set ting 6 Deactivate the applianc
18. uantity of detergent in the dispenser before you start a programme Make sure that you add de tergent in the dispenser be fore you start a programme Make sure that there is dish washer salt in the salt con tainer Make sure that the set level of the water softener agrees with the water hardness in your area Tighten the cap Decrease the released quan tity of rinse aid 20 Problem Possible cause Possible solution The quantity of detergent Make sure that you add the was too much correct quantity of detergent in the dispenser before you start aprogramme Dry water drop The released quantity of Increase the released quanti stains on glasses rinse aid was not sufficient ty of rinse aid and dishes The quality of the detergent Try a different brand of de can be the cause tergent The dishes are wet The programme had no drying phase e The programme had a low temperature drying phase For better drying results keep the door ajar for some minutes Make sure that there is rinse aid in the rinse aid dispenser The dishes are wet and matt The rinse aid dispenser is empty The quality of the rinse aid Try a different brand of rinse can be the cause aid The quality of the combi detergent tablets can be the cause e Try a different brand of combi detergent tablets e Activate the rinse aid dis penser and use the rinse aid together with the com bi detergent tab
19. y 4 Fresh soil Wash 60 C Quick Crockery and Rinse a 4 cutlery 5 Normal soil Prewash OKO PLUS ECO Crockery and Wash 50 C 50 gt cutlery Rinses Dry 6 Light soil Wash 55 C Quick Crockery and Rinses a cutlery 7 Normal or light Wash 45 C OKO PLUS Y 45 soil Rinses Delicate crockery Dry and glassware All Prewash 8 ans a DA 1 The appliance senses the type of soil and the quantity of items in the baskets It automatically adjusts the temperature and quantity of the water the energy consumption and the programme duration 2 This programme has a high temperature rinsing phase for better hygiene results During the rinsing phase the temperature stays at 70 C for 10 to 14 minutes 3 This is the most silent washing programme The pump works at a very low speed to decrease the level of noise Because of the low speed the programme duration is long 4 With this programme you can wash a load with fresh soil It gives good washing results in a short time 5 This is the standard programme for test institutes With this programme you have the most efficient use of water and energy consumption for crockery and cutlery with normal soil Refer to the supplied leaflet for test information 6 Use this programme to quickly rinse the dishes This prevents the remaining food to bond on the dishes and bad odours to come out from the appliance Do not use detergent with this programme ENGLISH 9 Consumption valu
Download Pdf Manuals
Related Search