EverFocus Polestar II ED610
Contents
1. 3 8 2 3 D ZOOM set the digital zoom OFF Disable the D ZOOM function e D Zoom Select digital zoom from X1 0 up to X32 To control the portion of the magnified image in view 0 is the center of the image e Pan Select pan digital zoom from 100 to 100 e Tilt Select tilt digital zoom from 100 to 100 e Return Select to save all settings in D ZOOM menu and returns to the previous menu e Select END to save all the menu settings and exit from the OSD menu 3 8 2 4 GAMMA To adjust displayed brightness from 0 05 up to 1 0 3 8 2 5 NEG IMAGE Allows user to create a negative of the original image A negative image is a tonal inversion of a positive image in which light areas appear dark and vice versa A negative color image is additionally color reversed with red areas appearing cyan greens appearing magenta and blues appearing yellow 3 8 2 6 RETURN select RET to save all settings in D EFFECT menu and returns to the previous menu select END to save all the menu settings and exit from OSD menu 3 8 3 MOTION This camera enables you to observe movements of objects in 4 different areas on the screen and the message MOTION DETECTED appears on the screen when movement is detected this may help to improve operational efficiency The camera detects an objects movement by sensing changes in the pixels displayed OFF Disables the MOTION function ON AREA SELECT Ple2. Press END to save all the menu settings and exit cr AE COLOR The picture is always displayed in color even at low light levels AUTO The picture switches to color in a normal bright environment and switches to B W when the ambient illumination is low The switching point is determined by the AGC level Note AGC selection must be set as middle or high in order to employ the auto switching function Delay Set the switchover delay time from 0 63 seconds o Level Set the start level from 0 100 E Level Set the end level from 0 100 EXT The picture switches to color in a normal environment and switches to B W when the ambient illumination is low The switching condition is determined by the light sensor alongside the lens 3 7 3DNR 3DNR reduces the background noise in a low luminance environment OFF Disables 3DNR to keep the same amount of noise ON Enables 3DNR to reduce the noise level adjust noise reduction level from 0 100 e Return Select to save all settings in 3DNR menu and returns to the previous menu select END to save all the menu settings and exit from the OSD menu 3 8 SPECIAL In this section user can control special settings including Cam Title D Effect Motion Privacy Sync Language and Return 1 Please direct the arrow to point to SPECIAL on the SETUP menu by moving the joystick UP and DOWN 2 Select the mode you would like to operate by moving the joystick LE
3. LE 26 CO BO ci alos tes 27 20 011010 050 c ME M EL MM MI A E M EI 28 DO PER 72109 NECEM 29 209 9 Nu tuer PL M M M E M per 29 20O LANGUAGE T 29 Sod DM m 29 2110 1 fre foe P gt 29 2 TS ARISNIES 22222 LEM A LR LOL 29 3202 BE MAL PL AM 8 30 SO uS SE 30 So NE e mE m mE ME AA ME AA E MEL mE 30 54110 5445 EM E EE E ONE EE AME E 30 eMe 30 22222202 ns E AT noe M 30 A 30 1 PRODUCT OVERVIEW Amazing color low light sensitivity of 05 lux before the added benefits of digital signal processing technology delivered by a 1 3 Sony Super HAD II sensor is just the beginning with the new EverFocus ED610 Get color without compromise 560TVL resolution your choice of full motion color or true day night images in low light without ghosting plus 120dB Digital Wide Dynamic Range to handle the most challenging of bright or unbalanced scene lighting condition
4. amp Configuration to get more details about OSD menu usage 2 2 4 Close the Camera Cover after installation is complete The ED610 is specially designed with one inner cover and one outer cover ring for water proofing and ease of installation Please follow these instructions for closing the camera cover 1 Align the window in the cover with the lens 2 Push the interior cover toward the base until it completely covers the whole red gasket and is lined up parallel with camera base The cover must be aligned with the camera base or it cannot be closed Then turn the outer cover ring clockwise to secure it tightly to the camera base Push the inner cover and cover the whole red gasket Outer cover ring 16 Correct Wrong not aligned 3 If the lens is not aligned with the window loosen the outer cover adjust the inner cover so that the lens aimed exactly at the window Slightly adjust the cover Turn the external ring 3 OSD MENU amp CONFIGURATION This chapter introduces how to configure the camera OSD menu Joystick 3 1 Access the user setup menu screen l Press inward on the end of the joystick The menu screen will appear on the monitor Navigating with the joystick Angle the joystick or w to move the cursor up or down Angle the joystick 4 or to adjust the mode or value of a setting Switching to sub menu screens When an item with sub menu is selected press in
5. 3 2 2 140115 001 ael POS N 13 2 2 2 A0 usling ZOOM aNd FOCUS 14 2 2 9 CAMEL AOS MING scii te mH t e Uri aed E 16 229 4 99D SER SOLD Mella 2 _ _ _ 16 2 2 4 Close the Camera Cover after installation is complete 16 S OSD MENU CONFIGURATION e th xci te apu o ee Pd Axe nee iw ete e Dae hr taa 18 3 1 Access the user setup menu 5 2222000 2 1 1000 nennen eene eene nennen nnne nasse RR RR RR senes 18 SPA EDG 10 Menu Tree 19 tutelam taba tutte et Cb cu UE 22 SE dap dus SUR E 5 22 SAT ORUTTE R RN UU UU UI 22 OZ OC AIO 21000010 22 S CH edad b 22 SH DS xo scii IE IM ME ME 23 RT RU E T TI EE EUR 24 eed UE Mu CCS E 24 QU MA TIVI MEN ERRORI RENTE 24 SJ Wille BALANCE CONTRO rt Lac UNES 25 2 0 214 5 RE 25 26 Su a 26 53524 021018 1 come EE c eI EE
6. ACTORY RESET Reset to the default settings 3 10 2 RETURN Select to save all settings in RESET menu and returns to the previous menu Select END to exit from OSD menu 3 11 EXIT Save all the menu settings and exit NOTE If you quit the Menu without pressing EXIT all the settings you previously modified will NOT be saved a EverFocus Electronics Corp Headquarter Office 12F No 79 Sec 1 Shin Tai Wu Road Hsi Chi Taipei Taiwan Tel 886 2 26982334 Fax 886 2 26982380 European Office Albert Einstein Strasse 1 D 46446 Emmerich Germany Tel 49 2822 9394 0 Fax 49 2822 939495 USA California Office 1801 Highland Ave Unit A Duarte CA 91010 U S A Tel 1 626 844 8888 Fax 1 626 844 8838 Your EverFocus product is designed manufactured with high quality materials and components which can be recycled and reused This symbol means that electrical and electronic equipment at their end of life should be of separately from your household EA dispose of this equipment at local community waste collection recycling centre In the European Union there are separate collection for used electrical electronic 2 help us to conserve the environment we ive in Ihr EverFocus Produkt wurde entwickelt und hergestellt mit qualitativ hochwertigen Materialien und aa recycelt und wieder verwendet werden Dieses Symbol bedeutet dim elektrische und e
7. FT or RIGHT 3 8 1 CAM TITLE Input a camera title and it will be displayed on the monitor 1 Please direct the arrow to point to CAMERA by moving the joystick UP or DOWN Select ON by moving the joystick LEFT or RIGHT Press in on the joystick Ww N Maximum 15 letters can be used for the ID Moving the joystick UP and DOWN position the cursor on the letter to be chosen Press in on the joystick to lock in the letters Repeat as necessary 5 Once a name has been selected please choose a position where you would like to display the name Move the cursor onto POS and press on the joystick B The name will appear at the top left hand corner m Angle the joystick in any direction to select the desired position to display the name Press in on the joystick to lock in the position 206 6 If you would like to cancel the ID entered please move the cursor to CLR press on the joystick and all the letters entered will be deleted 7 Select END and press in on the joystick to complete the ID input 3 8 2 D EFFECT 3 8 2 1 FREEZE Note that practical application of this feature requires direct access to the camera menu in real time OFF Select OFF to view moving pictures ON Select to view still pictures 3 8 2 2 MIRROR OFF Disable the effects MIRROR sets a horizontal image inversion V FLIP Set a vertical image inversion ROTATE Rotate the image 180
8. IJ 1 3 CCD Color Day Night plus Wide Dynamic Range Outdoor Vandal Dome Camera Operation Instructions Model No ED610 Please read this manual first for correct installation and operation This manual should be retained for future reference The information in this manual was current when published The manufacturer reserves the right to revise and improve its products All specifications are therefore subject to change without notice PRECAUTIONS 1 Do not install the camera near electric or magnetic fields Install the camera away from TV radio transmitters magnets electric motors transformers and audio speakers since the electromagnetic fields generated from these devices may distort the video image Never disassemble the camera beyond the recommendations in this manual nor introduce materials other than those recommended herein Improper disassembly or introduction of corrosive materials may result in equipment failure or other damage Try and avoid facing the camera toward the sun In some circumstances direct sunlight or may cause permanent damage to the sensor and or internal circuits Keep the power cord away from water and other liquids and never touch the power cord with wet hands Touching a wet power cord with hands or touching the power cord with wet hands may result in electric shock Never install the camera in areas exposed to oil gas or solvents Oil gas or solvents may result in equipm
9. OTE The brightness of the screen can be adjusted in the BRIGHTNESS sub menu The level can be adjusted from 0 to 100 2 Select RET to save all settings in the LENS menu and returns to the previous menu select END to save all the menu settings and exit from the OSD menu 3 4 EXPOSURE When the SETUP menu is displayed direct the arrow to EXPOSURE and press in on the joystick 3 4 1 SHUTTER 1 When the EXPOSURE menu is displayed on the screen please direct the arrow to point SHUTTER by moving the joystick UP or DOWN 2 Selectthe shutter mode by moving the joystick LEFT or RIGHT oelect from x256 x128 x64 x32 x16 x8 x4 x2 1 60 FLK 1 125 1 500 1 2000 1 5000 1 10000 1 00000 FLK Please select FLK mode if flickering occurs on the screen because of an irregular balance between illumination and scan frequency NTSC model 1 100 PAL model 1 120 3 4 2 AGC Auto Gain Control 1 Please direct the arrow to point to AGC by moving the joystick UP and DOWN 2 Select the mode you would like to operate by moving the joystick LEFT or RIGHT The more the level of gain increases the brighter the screen however the level of noise increases as well Please select from HIGH MIDDLE LOW and OFF 3 4 3 SENSE UP SENSE UP 15 used to keep a brilliant vivid screen image by automatically detecting changes in the level of light under low light level conditions 1 Please direct the arrow to point to
10. Off Mirror V Flip Rotate Selectable IP66 S 24VAC 3W max 123mm O D x 107 8mm H 4 8 O D x 4 2 H 1 4 Dimensions 123mm x 107 8mm 4 8 x 4 2 123 4 8 lJ 107 8mm 4 2 5 143mm 0 2 94 3 78 1 5 Camera Component Description Exterior view Base Outer Cover ring Rotatable cover Interior view OSD joystick Power board 1 6 Front and Back Panel Layout Front Panel Layout Back Panel Layout 1 External Light Sensor External Light sensor is used to detect the lighting level the environment The light sensor is down when the internal camera module is properly positioned 2 Focus Ring To set the focus and loosen the focus ring knob and turn the ring toward F or N as necessary and re tighten when the adjustment is complete 3 Zoom Ring To adjust the viewing angle loosen the zoom ring knob Turn the ring toward W to Zoom out or lt T gt to Zoom in as necessary and re tighten when the adjustment is complete 4 Lens The included vari focal DC iris lens allows manual adjustment of the field of view zoom amp focus The choices for focal length range are e 2 8 10mm e 922 5 Power amp Video pigtail cable Connect power and video to pigtail cable 6 Test Video Output Connector When installing the camera you can use this video connector to connect a portable monitor This will allow you to ea
11. SENSE UP by moving the joystick and DOWN 2 Select the mode you would like to operate by moving the joystick LEFT or RIGHT AUTO Low light level auto mode OFF The function is disabled 9227 NOTES D The maximum amplification in low light level situations can be adjusted by pressing the SETUP button in AUTO mode This sets an upper limit on the boost 2 The image becomes brighter when the setting increases however the after image increases as well Due to the increased light sensitivity of the Super Had II chip far less DSP boost is needed resulting in color or B W images in low light with minimal ghosting 3 Please note that spots and noise may appear if light amplification increases when SENSE UP 15 operating This is a normal phenomenon controllable with DNR 3 4 4 BLC Video gain can be adjusted automatically to correct the exposure of subjects that are in front of a bright light source 1 Please direct the arrow to point to by moving the joystick UP and DOWN 2 Select the BLC mode by pressing the LEFT or RIGHT button Then make adjustments as below GAIN select from High Middle and Low DEFAULT set the factory default values for BLC LEFT RIGHT oet the Left Right side of an area for the BLC to be adjusted The value adjustable is 0 6 WIDTH set the width of an area for the BLC to be adjusted The value adjustable is 0 6 TOP BOTTOM set the Top Bottom side of a
12. ase select the area you would like to detect from the 4 areas in AREA SELECT mode AREA DISPLAY Select ON to use the motion area selected in sensitivity Select OFF to disable this function LEFT RIGHT Set the coordinate of the horizontal axis 5 66 WIDTH Set the size of horizontal area 0 93 TOP BOTTOM Set the coordinate of the vertical axis 1 60 HEIGHT Set the size of vertical area 0 60 SENSITIVITY Set the sensitivity level for the motion trigger by selecting from 0 40 When the sensitivity value is high motion detection sensitivity increases to sense very small movements and vice versa MOTION VIEW Select ON to display motion detection pixels in the live view select RET to save all settings in MOTION menu and returns to the previous menu select END to save all the menu settings and exit from OSD menu 28 3 8 4 PRIVACY This mode covers the areas you do not want to see on the screen OFF Disable the PRIVACY function ON AREA SELECT Please select the area you would like to hide from the 8 areas in AREA SELECT mode AREA DISPLAY Select to use the area selected in the AREA SELECT Select OFF to disable this function LEFT RIGHT Set the coordinate of the horizontal axis 6 98 WIDTH Set the size of horizontal area 0 93 TOP BOTTOM Set the coordinate of the vertical axis 0 60 HEIGHT Set the size of vertical area 0 61 COLOR Set area color It is selectable fro
13. en the focus ring knob then turn the ring towards lt gt or as necessary to obtain a clear video image 3 Repeat steps 1 and 2 until the best image is obtained Once the lens setting is complete tighten the zoom and focus ring knobs Important Note when focusing a 9 22mm Lens To adjust lens zoom and focus if using the 9 22mm lens model ED610 camera the focus aiding lens cap must be used to simulate the dome being closed Follow the steps below to ensure that camera will stay in focus when the dome is installed Step 1 Take the included focus aiding lens cap shown below from its small plastic bag 14 step 2 Open the dome cover and place the Focus aiding lens cap on the lens making sure that the 5 notch is resting on the zoom knob otep3 With cap on adjust the focus and zoom rings by loosening the knobs and turning the rings until subject is in focus Retighten the knobs when done otep4 When finished adjusting focus and zoom remove the focus aiding cap from the camera lens replace the dome cover and secure the cover by turning it clockwise See Section 2 2 4 below for additional information NOTE It is recommended to put the desiccant pack under the bracket Or use a cable tie to secure it before placing the cover back on the camera 15 2 2 3 Camera Setting 2 2 3 1 OSD User Setup Menu This camera utilizes an On Screen Display OSD user setup menu Please refer to Chapter 3 OSD Menu
14. ent failure electric shock or in extreme cases fire Cleaning Do not touch the surface of the sensor directly with the hands Use a damp soft cloth to remove any dirt from the camera body Use lens tissue or a cotton tipped applicator and ethanol to clean the sensor and the camera lens Please do not use complex solvents corrosive or abrasive agents for cleaning Do not operate the camera beyond the specified temperature humidity or power source ratings Use the camera at temperatures within 10 C 50 C 14 122 and in an IP66 complaint environment this device is not rated as submersible The input power source is 12VDC 24VAC TABLE OF CONTENTS 0 OVERVIE RENT TM 3 RR 3 UA Soncd EE 3 PEME UO xd tutt 5 1 55 615101 cata aut ins dota et EE st 6 1 5 Camera Component 7 1 06 Fr n tand Back Paner aec tta iet 8 Produ oea 9 2 MIN TATE TION saa E ENA 10 210100 00 10 PAS HAN c 15320 oh NR RETE ONE 10 PAX PA 11 22801200 GIN BTG 1
15. lect RET to save all settings in HSBLC menu and returns to the previous menu select END to save all the menu settings and exit from the OSD menu 3 4 6 D WDR When there are both bright and dark areas at same time this function can make both areas properly exposed 1 Please direct the arrow to point to D WDR by using the UP and DOWN buttons 2 Select the mode you would like to operate by moving the joystick LEFT or RIGHT OFF Disables D WDR function INDOOR Select this option if you are in an indoor environment OUTDOOR Select this option if you are in an outdoor environment 3 4 7 Return select RET to save all settings in the EXPOSURE menu and returns to the previous menu Select END to save all the menu settings and exit from the OSD menu 24 3 5 WHITE BALANCE CONTROL The screen color can be adjusted by using the WHITE BALANCE function 1 Please direct the arrow to point to WHITE BAL by moving the joystick UP and DOWN 2 Please select the mode you would like to operate by moving the joystick LEFT or RIGHT Please select one of the 6 modes below ATW Auto Tracking White Balance This mode can be used within the color temperature range from 5 500 to 6 000 K eg fluorescent light outdoor sodium vapor lamp or inside tunnels AWB This mode can be used within the color temperature range from 2 500 K to 10 000 K AWC gt SET To find the optimal setting for the current lumina
16. lektronische Ger te Ende ihrer Nutzungsdauer vom Hausm ll getrennt entsorgt werden sollen Bitte entsorgen Sie dieses Ger t bei Ihrer rtlichen en Sammelstelle oder im Recycling Cen Helfen Sie bitte die Umwelt zu erhalten in set EverFocus Beijing office Room 609 Technology Trade Building Shangdi Information Industry Base Haidian District Beijing China Tel 86 10 62971096 Fax 86 10 62971423 Japan Office 1809 WBG Marive East 18F 2 6 Nakase Mihama ku Chiba city 261 7118 Japan Tel 81 43 212 8188 Fax 81 43 297 0081 USA New York Office 415 Oser Ave Unit S Hauppauge NY 11788 Sales 1 631 436 5070 Fax 1 631 436 5027 P N MED6G00100
17. ll the items listed below inside the original box Camera Unit x 1 This Operation Manual x 1 Mounting kit includes Long Screws x 3 for mounting the base Expanding Anchors x 3 Washers x 3 Installation Template Sticker x 1 Video Test Cable x 1 Power Adapter Cable x 1 d Desiccant Pack x 1 Focus Aiding Lens Cap for 9 22mm models only x 1 Please Note If an item appears to have been damaged in shipment replace it properly in its carton and notify the shipper If any items are missing notify your EverFocus Electronics Corp Sales Representative or Customer Service The shipping carton is the safest container in which the unit may be transported Save it for possible future use 1 3 Specifications tems ickup Device ideo Format scanning System icture Elements orizontal Resolution ensitivit IN Ratio lectronic Shutter ideo Outputs amma Correction ens Type ack Light Comp uto Gain Control White Balance nc Mode ay amp Night SD Menu DNR WDR igital Slow Shutter irror igital Zoom otion Detection rivacy Mask eatherproof andal Resistant ower Source Power Consumption perating Temperature Weatherproof imensions eight ertifications PAL 625 TVL 50 fields sec Over 52dB AGC off 1 50 1 60 1 100 000 1 1 0 Vp p 7 2 Additional testing video output 1 0 Vp p 5ohm Yes Auto Color BWEXT Off On switchable Outdoor Indoor oens Up 256x
18. m 0 10 15 Select RET to save all settings in PRIVACY menu and returns to the previous menu select END to save all the menu settings and exit from OSD menu 3 8 5 SYNC There are two SYNCHRONIZATION modes INTERNAL and EXTERNAL LINE LOCK In LINE LOCK mode the video signal is synchronized to the frequency of the incoming AC power The Line Lock synchronization can only be used when the supply power is 24VAC 60Hz NTSC models or 50Hz PAL models INT Internal synchronization L L External line lock synchronization 3 8 6 LANGUAGE select OSD language ED610 camera supports multiple languages 3 8 7 RETURN select RET to save all settings in SPECIAL menu and returns to the previous menu Select END to save all the menu settings and exit from OSD menu 3 9 ADJUST Adjust sharpness Blue and Red level in this section 3 9 1 SHARPNESS The contour of the video image becomes cleaner and more easily distinguished as the level of SHARPNESS increases If the level is set too high it may affect the video image and cause noise The available range of level is 0 31 29 3 9 2 BLUE Adjust image s blue level The available range of level is 0 100 3 9 3 RED Adjust image s red level The available range of level is 0 100 3 9 4 RETURN select RET to save all settings in ADJUST menu and returns to the previous menu select END to save all the menu settings and exit from OSD menu 3 10 RESET 3 10 1 F
19. n area for the BLC to be adjusted The value adjustable is 0 6 HEIGHT set the height of an area for the BLC to be adjusted The value adjustable is 0 6 select RET to save all settings in this menu and returns to the previous menu select END to save all the menu settings and exit 82217 3 4 5 HSBLC HSBLC Highlight Suppression BLC is used to reduce the brightness of light sources in a specific area lt is activated only in a low illumination environment to minimize the effects of glare from bright lights such as spotlights street lights or headlights in the field of view Where traditional BLC can increase the exposure of a dark area surrounded by a brighter area HSBLC can decrease the exposure of bright areas surrounded by darker areas 1 Please direct the arrow to point to BLC by using the UP and DOWN buttons 2 Select the HSBLC mode by pressing the LEFT or RIGHT button Then make adjustments as below LEVEL Adjust the sensitivity level for HSBLC from 0 to 8 DEFAULT Set the factory default values for HSBLC LEFT RIGHT Set the Left Right side of an area for the HSBLC to be adjusted The value adjustable is 0 6 WIDTH Set the width of an area for the HSBLC to be adjusted The value adjustable is 0 6 TOP BOTTOM Set the Top Bottom side of an area for the HSBLC to be adjusted The value adjustable is 0 6 HEIGHT Set the height of an area for the HSBLC to be adjusted The value adjustable is 0 6 Se
20. nce environment in this mode point the camera toward a sheet of white paper and press middle of joystick If the environment changes you have to readjust it MANUAL The manual adjustment mode enables a more precise adjustment Please select ATW or AWC first Then change to manual adjustment mode and press middle of joystick Set the suitable color temperature and increase or decrease the red and blue color values at the same time while checking the color changes of the objects in view select RET to save all settings in this menu and returns to the previous menu select END to save all the menu settings and exit INDOOR Select this option when the color temperature is 5 600 K OUTDOOR Select this option when the color temperature is 3 300 K Press to save all settings in this menu and returns to the previous menu Press END to save all the menu settings and exit 3 6 DAY NIGHT These settings control the operation of the camera when the illumination level changes Choices are Color at all times B W at all times or color when illumination is bright switching to B W in low light B W The picture is always displayed in B W BURST OFF ON ON Retains the color burst information minor color noises may appear when ambient illumination is low OFF With color burst signal off picture will be pure B W Return Press to save all settings in the DAY NIGHT menu and returns to the previous menu
21. s Vandal resistant IP66 with varifocal auto iris lens 3 axis positioning dual voltage operation and a full suite of OSD Menu and DSP functions 3D DNR to save DVR HDD space privacy masking 32X digital zoom mirroring and rotation 256X sens up to a max of 0002 lux and much more this is the camera you have been waiting for and might be the only camera you ll ever need 1 1 Main Features e Super HAD sensor at 05 lux has 5X better native light sensitivity before DSP low light boost e Color without compromise your choice of full motion color or true day night images in low light without ghosting e True Day Night with ICR module e Starlight super high sensitivity of 0 0002 Lux F 1 2 is achieved through a sensitivity increase setting of up to 256x Digital Wide Dynamic Range expansion to deliver properly exposed images despite bright light sources deep shadows and or unbalanced lighting in the same scene Provides 3D Noise Reduction to improve picture clarity while enabling DVRs to improve disk storage utilization 3 axis positioning for wall or ceiling mounting with flexible angle viewing Easy to use OSD setup menu Motion detection for 4 configurable zones Privacy mask function for 8 configurable zones Provides digital zoom up to 32x Dual voltage 12VDC 24VAC with line lock to AC supply 1 2 Content List 3 Please be careful when you unpack the box and the electronic devices inside Check and make sure that you have a
22. sily adjust camera s field of view and focus 7 OSD Menu joystick Use the joystick to move the cursor Upwards Downwards This is used to select the item to be set Tilt the stick to the right or left This is used to select or adjust the parameters of the selected item Press in on the stick to enter the setup menu If the item has its own setting menu sign 4 press the stick again to display the sub menu 1 7 Related Products In addition you may order the following EverFocus products which are recommended for use with the camera to achieve the best performance L Type Bracket BA EDMS 4 h EN220 5 6 inch LCD Test Monitor 2 INSTALLATION This chapter will describe in general terms how to install the ED610 camera STEPS 2 1 Mounting Camera 1 Drill the Holes See 2 1 1 2 Mounting See 2 1 2 2 2 Adjusting Camera 1 Adjust the camera position See 2 2 1 2 Adjusting Zoom and Focus See 2 2 2 3 Camera Setting See 2 2 3 4 How to close camera cover after installation See 2 2 4 Warning prevent electrical shock turn off the electrical power before making electrical connections Do not expose the camera to water or moisture while open during installation nor try to operate it while open in wet areas Once properly installed and sealed the dome is IP66 rated against water infiltration 2 1 Mounting Camera 2 1 1 Drill the Holes 1 Paste the drilling templa
23. te on the ceiling or wall 2 Drill 4 holes 1 for the power video cable 3 for screws A B and Screw hole A Screw hole C Installation sticker Screw hole B 10 Wire outlet hole for Surface mounting Power Video Cable Screw Camera base 2 1 2 Mounting 1 Take off camera s cover by rotating the cover counter clockwise OO Loose outer cover ring first Take off camera s cover 11 2 Pullthe cables to be connected to the power and video cables from the ceiling or wall Video output 6 3 Fix the camera base to ceiling or wall by using 3 screws and washers The washers are used to create the IP66 seal and must be used Ceiling Mount Wall Mount 2 2 Adjusting Camera 2 2 1 Adjusting Camera Position Adjust the camera to best angle for viewing Module can be adjusted up and down 2 2 2 Adjusting Zoom and Focus It is highly recommended to use an EverFocus Test Monitor to set up the camera Find the Video test connection on the back of the camera module Connect using the video cable included in the package Video out Connect with Test Monitor Loosen the zoom ring knob and then turn the ring towards W or T as necessary to obtain the desired view angle W side Zoom out The viewing range will be wider and the subject is smaller T side Zoom in The viewing range will be smaller and the subject is larger 2 Loos
24. ward on the end of the joystick to switch to the sub menu for further settings NOTE For those selected items with ll sign at the end there is a sub menu for further settings IV Return to previous page Press the SET button to return to previous page if the choice displayed is RETURN V Close the menu screen Press the SET button to exit the menu system if the choice displayed is END sub menu or EXIT main menu only 18 3 2 ED610 Menu Tree LENZ 256 128 x64 x32 x16 xd x2 1 50 1 250 1 500 1 2000 1 5000 1710000 17100000 L Lr T Cr ATH DEFAULT LEFTRIGHT EXPOSUEE DEFAULT LEFT RIGHT 06 TOPI BOTTOM HEIGHT EETUEH D WDR OFF INDOOR OU TDOOR 9 D EFFECT 100 100 GE 5 PECIAL ID DIE PLAY OFF ON BAUD RATE 2400 AUD S600 19200 38400 57600 AREAS ELECT AREA DISPLAY OFF OH LEFT EIGHT WIDTH 0 93 5 HEIGHT 0 50 SENSITIVITY MOTION VIEW ee PRIVACY AREAS ELECT ARFA AREAS AREA DISPLAY OFF LEFT EIGHT Er 0 93 5 5 3 0 HEIGHT 0 81 COLOR 0 15 LANGUAGE ENGLISH ET 3 3 LENS 1 When the SETUP menu is displayed on the screen please direct the arrow to point to LENS by moving the joystick UP and DOWN N
Download Pdf Manuals
Related Search