Philips new home air purifier AC4076
Contents
1. insert the bottom hooks into the bottom of the appliance first 1 Then push the panel against the body of the appliance 2 10 ENGLISH Using the appliance Put the plug in the wall socket All lights go on twice and you hear a beep Then the lights go out again Press and hold the on off button for 2 seconds to switch on the appliance D The power on light the AUTO light and the AIR QUALITY light on the control panel go on ofiz gt gt i lt V eo oy SILENT The air quality light ring shows the quality of the air A Air quality indication Colour Air quality Blue very good Deep purple good Purple fair Red bad To switch off the air quality light ring press the AIR QUALITY button Note The air quality light ring automatically goes on when the appliance is switched on D The appliance automatically starts operating in the AUTO mode To switch off the appliance press and hold the on off button again until the power on light goes out and unplug the appliance Note When the humidity level in the room is very high it is possible that condensation develops on the air quality sensor As a result the AIR QUALITY light on the control panel and the air quality light ring may indicate that the air quality is bad even though the air quality is good In this case the auto ENGLISH 11 mode causes the appliance to run at high fan speed Y2. 2 New home filter back into the appliance Note Make sure that the side with the tag is pointing towards you Put filter 1 pre filter back into the appliance Note Make sure that the side with the two projections is pointing towards you Note Make sure that all hooks are properly attached to the appliance EJ To reattach the front panel insert the bottom hooks into the bottom of the appliance first 1 Then push the panel against the body of the appliance 2 EEJ Put the plug in the wall socket and switch on the appliance again Press the filter reset button with a thin tool Note You do not need to press the filter reset button after cleaning filter 1 pre filter Note You cannot reset the appliance when you replace a filter before its filter replacement light starts flashing Note You cannot reset the appliance if it is not plugged in and switched on Storage To store the mains cord wind it round the cord storage facility at the bottom of the appliance Accessories New filters are available under the following type numbers Filter Type number Filter 2 High Capacity Formaldehyde Particle AC4147 New Home filter ENGLISH 19 Environment Do not throw away the appliance with the normal household waste at the end of its life but hand it in at an official collection point for recycling By doing this you help to preserve the environment Guarantee and service If you need informati
3. 30cm free space above the appliance Do not place anything on top of the appliance and do not sit on the appliance Do not place the appliance directly below an air conditioner to prevent condensation from dripping onto the appliance Make sure all filters are properly installed before you switch on the appliance Only use the original Philips filters specially intended for this appliance Do not use any other filters Avoid knocking against the appliance the air inlet and outlet in particular with hard objects Always lift or move the appliance by the handle at the back of the appliance 8 ENGLISH Do not insert your fingers or objects into the air outlet Do not use this appliance when you have used indoor smoke type insect repellents or in places with oily residues burning incense or chemical fumes Do not use the appliance near gas appliances heating devices or fireplaces Always unplug the appliance after use and before you clean it Do not use the appliance in a room with major temperature changes as this may cause condensation inside the appliance The appliance is only intended for household use under normal operating conditions Do not use the appliance In wet surroundings or In surroundings with high ambient temperatures such as the bathroom toilet or kitchen The appliance does not remove carbon monoxide CO or radon Rn It cannot be used as a safety device in case of accidents with combustion pro
4. Register your product and get Support at www philips com welcome AC4076 English 6 39 fal ASFA 23 PHILIPS REPLACE FILTER REPLACE FILTER N 234567 Swe Danne d SSS SMR ee ER SS RR X OCN SS SSS SS MARRS LSe SSSR 6 ENGLISH Introduction Congratulations on your purchase and welcome to Philips To fully benefit from the support that Philips offers register your product at www philips com welcome With this new home air purifier you breathe cleaner air in your new or newly decorated home For the best result place the New home air purifier in a room where you spend most of your time e g your bedroom living room or children s room There are many pollution sources In a new or newly decorated home there js high condensation of formaldehyde and other harmful gases coming from furniture paints and smoking and etc Because of these harmful gases are invisible and odorless they can affect your health The New home air purifier filters off these harmful gases quickly and effectively Furthermore it can also filter out pollutants such as pollens airborne particles that can affect your well being With our new home air purifier it improves the air quality and ensures you and your family members breathe cleaner air at your home Filtration in a professional and credible way The new home air purifier has all in one Hi
5. cesses and hazardous chemicals Electromagnetic fields EMF This Philips appliance complies with all standards regarding electromagnetic fields EMF If handled properly and according to the instructions In this user manual the appliance is safe to use based on scientific evidence available today Before first use Placing the filters The appliance comes with all filters fitted inside but you have to remove the packaging of the filters before you can use the appliance Remove all filters unpack them and place them back into the appliance as described below Tip Place the appliance against a wall for more stability when you remove or insert filters Note Make sure you insert the filters in the correct position Place your fingers in the recesses of the side panels and gently pull the top part of the front panel towards you Then lift the hooks at the bottom of the panel out of the bottom of the appliance Y NN z QQ _ F ENGLISH 9 Remove the filters from the appliance Take out the new filter from the packaging material Put filter 2 New home filter back into the appliance Note Make sure that the side with the tag is pointing towards you Place filter 1 pre filter in the appliance Note Make sure that the side with the two projections is pointing towards you Note Make sure that all hooks are properly attached to the appliance EJ To reattach the front panel
6. e AUTO light goes on The FAN SPEED light indicates at which fan speed the appliance is operating Note When the air quality is very good and the appliance operates at a very low fan speed the FAN SPEED light for the lowest speed setting does not go on In this case only the power on light and the AUTO light are on Note The built in air quality sensor measures the air quality and automatically selects the appropriate speed setting to ensure the best possible air quality in your room When the air is clean the appliance stops running When the air quality deteriorates the appliance starts running at a low fan speed and noise level so that the energy consumption is minimised Ne Quality Ss lt SILENT ae Ne ov ALTY NS G 6 SILENT IE mee a REPLACE Ta FILTER FARM ENGLISH 13 Night mode The appliance works in harmony with its surroundings In auto mode the appliance automatically switches to night mode when the room in which it is operating becomes dark When the room has been dark for 3 minutes the lights of the appliance go out the fan speed and noise level are reduced and the energy consumption is minimised If the room becomes bright again for 5 minutes or longer the appliance resumes normal operation In night mode the automatic control is still active If the air is clean the lights and the fan are off If the air quality deteriorates
7. ew minutes WY ALITY eo Press the AIR QUALITY button and simultaneously put the mains RE plug in the wall socket The appliance beeps twice and one of the fan speed lights flashes to ex show the current sensitivity level of the air quality sensor Sensitivity level Fan speed light Sensitivity level extra sensitive sensitive standard Weed 12 ENGLISH Ne ALITY 8 eo gt o SILENT ae Ne Quality S A Go SILENT ae Ne VAUTY eS o SILENT ee o4 on N ou on N Press the FAN SPEED button to adjust the sensitivity level of the air quality sensor One of the fan speed lights flashes to show the set sensitivity level of the air quality sensor Press and hold the on off button to switch off the appliance Note When you change the sensitivity level the appliance automatically starts operating at the set sensitivity level whenever you switch on the appliance Auto mode When the appliance is switched on the built in air quality sensor automatically measures the ambient air quality When the auto mode is activated the appliance selects the most appropriate fan speed for the measured air quality Press the on off button to switch on the appliance Press the AUTO button to activate the auto mode Note When the appliance is operating in another mode and you want to activate the auto mode simply press the AUTO button Th
8. gh capacity formaldehyde new home filter that ensures the best air quality in your new or newly decorated home Stage 1 The pre filter has been treated with antibacterial substances It catches big particles like human hair pet hair etc Stage 2 The high capacity formaldehyde new home filter effectively removes formaldehyde odors and other volatile organic compounds VOCs New home filter AC4147 supplied with AC4076 and AC4016 General description Fig 1 Air quality light ring Fan speed indicator Air quality sensor outlet Air quality sensor Air quality sensor inlet Handle Air outlet Air inlet Cord storage facility Mains cord Control panel Light sensor for night mode AIR QUALITY on off button with light Power on off button SILENT button with light Power on button with light FAN SPEED button with light AUTO button with light Fan speed lights 1 2 3 and boost power filter replacement lights FAN SPEED indications 10 REPLACE FILTER indications L Filter 2 High capacity formaldehyde particle new home filter OOANKDUOBRWNARART TOMMM OOA gt Y ENGLISH 7 M Filter 1 pre filter N Front panel Read this user manual carefully before you use the appliance and save it for future reference Danger Do not let water or any other liquid or flammable detergent enter the appliance to avoid electric shock and or a fire hazard Do not clean the appliance with water or any other liquid or a flam
9. h the two projections is pointing towards you EJ To reattach the front panel insert the bottom hooks into the bottom of the appliance first 1 Then push the panel against the body of the appliance 2 Air quality sensor Clean the air quality sensor every 2 months for optimal functioning of the appliance Clean it more frequently if you use the appliance in a dusty environment Note When the humidity level in the room is very high it is possible that condensation develops on the air quality sensor As a result the AIR QUALITY light on the control panel and the air quality light ring may indicate that the air quality is bad even though the air quality is good In this case you have to clean the air quality sensor or use one of the manual speed settings Clean the air quality sensor inlet and the air quality sensor outlet with a soft brush Remove the air quality sensor cover 16 ENGLISH Clean the air quality sensor the dust inlet and the dust outlet with a lightly moistened cotton swab Dry them with a dry cotton swab Reattach the air quality sensor cover Filter replacement Filter maintenance This appliance is equipped with the Healthy air protect lock to ensure that the filters are In optimal condition when the appliance is operating When one of the filters is almost full and has to be cleaned or replaced the appropriate filter replacement light starts to flash When you do not replace the New home fi
10. lter the appliance stops operating and the appliance is locked When the appliance is locked the filter replacement light of the filter concerned lights up on continuously Note Only replace a filter when the filter replacement light flashes If you replace the filter before the filter replacement light starts flashing the lifetime counter will not be reset but will continue counting the lifetime of the previous filter As a result the filter replacement light will start flashing much too soon Filter replacement lights The filter replacement lights indicate which filter has to be cleaned or replaced Filter replacement light 1 flashes filter 1 the pre filter has to be cleaned See chapter Cleaning for further instructions REPLACE FILTER Filter replacement light 2 flashes the New home filter has to be replaced RUTON a O o PS See LEAN TER mafal sata Ne TV YALI ENGLISH 17 Healthy air protect lock If you do not replace the filter in time the appliance stops operating approx 2 weeks after the filter replacement light started flashing When the appliance is locked it does not operate until you have replaced with the new filter and pressed the reset button Note When filter replacement lights 2 and REPLACE FILTER on the control panel are on continuously the appliance is locked see section Filter maintenance in this chapter for more informati
11. mable detergent to avoid electric shock and or a fire hazard Warning Check if the voltage indicated on the bottom of the appliance corresponds to the local mains voltage before you connect the appliance Ifthe mains cord is damaged you must have it replaced by Philips a service centre authorised by Philips or similarly qualified persons in order to avoid a hazard Do not use the appliance if the plug the mains cord or the appliance itself is damaged This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety Children should be supervised to ensure that they do not play with the appliance Do not block the air inlet and outlet e g by placing items on the air outlet or in front of the air inlet Caution This appliance is not a substitute for proper ventilation regular vacuum cleaning or use of an extractor hood or fan while cooking Ifthe wall socket used to power the appliance has poor connections the plug of the appliance becomes hot Make sure you plug the appliance into a properly connected wall socket Always place and use the appliance on a dry stable level and horizontal surface Leave at least 20cm free space behind and on both sides of the appliance and leave at least
12. on How long it takes before the appliance is locked depends on the operating time and speed level selected after the filter replacement alert ae Approximately 1 day before the appliance locks it beeps every 30 minutes 6 ooo to inform you that one of the filters needs to be replaced When the appliance is locked you hear a beep when you press any button You can switch off the appliance by pressing and holding the on off button If the appliance is locked Check which filter needs to be replaced see section Filter replacement lights Switch off the appliance and unplug it Replace the appropriate filter see section Replacing the filters Replacing the filters Tip Place the appliance against a wall for more stability when you remove or insert filters Switch off the appliance and unplug it Place your fingers in the recesses of the side panels and gently pull the top part of the front panel towards you Then lift the hooks at the bottom of the panel out of the bottom of the appliance ma SSS ma SSS SNS To remove filter 1 pre filter grab the two projections and pull the filter towards you NN aaa A S Wy SSE To remove filter 2 New home filter grab its tag and pull it towards you Discard the filter that needs to be replaced and unpack the new filter 18 ENGLISH EJ Put filter
13. on or if you have a problem please visit the Philips website at www philips com or contact the Philips Consumer Care Centre In your country you find its phone number in the worldwide guarantee leaflet If there is no Consumer Care Centre in your country go to your local Philips dealer Troubleshooting Problem This chapter summarises the most common problems you could encounter with the appliance If you are unable to solve the problem with the information below contact the Consumer Care Centre in your country Possible solution Buttons are not responding No air comes out of the air outlet The fan speed does not change when the AUTO mode is activated The airflow that comes out of the air outlet js significantly weaker than before The air quality does not improve even though the appliance has been operating for a long time Replace the New home filter when the filter replacement light started flashing and the appliance has sounded every 30 minutes after approx 2 weeks Replace the filter and reset the appliance see chapter Filter replacement so that the appliance can operate again The appliance is not switched on Put the plug in the wall socket and switch on the appliance The air quality is good and the auto mode is activated In this case the appliance switches off automatically when the air js clean to save electricity When the room becomes dark the night mode is activated automaticall
14. ou can solve this by cleaning the air quality sensor If condensation develops frequently during periods of high humidity we advise you to use one of the manual speed settings Fan speed lights filter replacement lights The lights on the right hand side of the control panel have a dual function they either indicate the fan speed or they indicate that the filters should be replaced or cleaned When lights 1 to 2 light up continuously they indicate the current fan speed When light 1 flashes you have to clean the pre filter When lights 2 0 flashes you have to replace the New home filter When light 2 and the REPLACE FILTER light are flashing continuously the New home filter have to replace and the appliance is locked see chapter Filter replacement lock for more information Adjusting the air quality sensor sensitivity People with certain health problems e g allergies or asthma have a greater need for healthy air For this reason the appliance allows you to adjust the sensitivity of the air quality sensor If you set it to higher sensitivity level the appliance starts cleaning the air at lower pollution level There are 3 sensitivity levels standard sensitive extra sensitive The pollution sensor is set to standard sensitivity by default You can adjust the sensitivity of the air quality sensor in the following way z If the appliance is already plugged in unplug the appliance and wait for a f
15. pliance and unplug tt Take the keeps flashing purple appliance to your Philips dealer or an authorised Philips service centre PHILIPS Specifications are subject to change without notice Ley 2011 Koninklijke Philips Electronics N V EO All rights reserved 3140 035 26571 1216317
16. rom collecting on the inside and outside Wipe away dust with a soft dry cloth from the body of the appliance Clean the air inlet and the air outlet with a soft dry cloth Pre filter The pre filter is washable Clean the pre filter when the first filter replacement light flashes to ensure optimal functioning of the appliance Place your fingers in the recesses of the side panels and gently pull the top part of the front panel towards you Then lift the hooks at the bottom of the panel out of the bottom of the appliance ENGLISH 15 SS To remove the pre filter grab the two projections and pull the filter towards you eS SS cs Ck SA ASS SS SASS SS a Wash the pre filter under a running tap If the pre filter is very dirty use a soft brush to brush away the dust SS Annan ss SS SSS aa Cees Tip Alternatively you can clean the pre filter by removing the dust with a vacuum cleaner eS ETS SS SS Se ny oss Air dry the pre filter Note Make sure that the pre filter is completely dry If it is still wet bacteria may multiply in it and shorten the lifetime of the pre filter Put the pre filter back into the appliance Attach all hooks properly to the appliance Note Make sure that the side wit
17. t removed all packaging material from the filters Make sure that loud you have removed all packaging material The appliance still indicates Perhaps you did not press the filter reset button properly Plug in the that need to replace a appliance press and hold the on off button and press the filter reset filter but already did button with a flat tool The appliance stops The built in quality sensor has determined that the air quality is good and operating although the that the air does not need to be cleaned anymore When the air quality power on light is still on deteriorates the appliance starts running at a low fan speed and noise level so that the energy consumption Is minimised The appliance does not This is a component defect Contact the Consumer Care Centre in your work Fan speed lights 1 country you find its phone number in the worldwide guarantee leaflet If and 2 flash all other lights there is no Consumer Care Centre in your country go to your local Philips are out dealer The appliance does not This is air particle sensor error or an air particle sensor and gas sensor work The air quality error Contact the Consumer Care Centre in your country you find light ring flashes blue all its phone number in the worldwide guarantee leaflet If there is no other lights are out Consumer Care Centre in your country go to your local Philips dealer The air quality light ring This is a gas sensor error Switch off the ap
18. the appliance is activated and the lights and the fan come on again Note The night mode only works when the appliance is operating in the auto mode Fan speed If you do not use the auto mode you can select the desired fan speed yourself Press the on off button to switch on the appliance Press the FAN SPEED button one or more times to select the desired fan speed The corresponding fan speed light and the indications above the lights show the set fan speed S or gt The corresponding fan speed light in the fan speed indicator goes on Note Select boost power if you need an extra strong airflow when the air in the room is very dirty Lights to amp light go on 14 ENGLISH Ne QUALITY SS SILENT ee Silent mode When you use the appliance in silent mode it operates very quietly Press and hold the on off button to switch on the appliance Press the SILENT button to activate the silent mode The SILENT light goes on If you want to go back to the FAN SPEED mode or AUTO mode simply press the FAN SPEED or AUTO button Always unplug the appliance before you clean it Never immerse the appliance in water or any other liquid Never use aggressive or flammable cleaning agents such as bleach or alcohol to clean any part of the appliance Only the pre filter is washable Body of the appliance Regularly clean the inside and outside of the body to prevent dust f
19. y when the appliance is in auto mode In this case the fan speed js set to a very low level If you want to change the fan speed press the FAN SPEED button one or more times to set the desired fan speed The pre filter is dirty Clean the pre filter see chapter Cleaning You haven t removed all packaging material from the filters Make sure that you have removed all packaging material One of the filters has not been placed in the appliance Make sure that all filters are properly installed in the following order starting with the innermost filter 1 New home filter 2 pre filter 20 ENGLISH Problem Possible solution The air quality sensor is wet The humidity level in your room is high and causes condensation Make sure that the air quality sensor is clean and dry see chapter Cleaning The room in which you run the appliance is larger than 55m which is the maximum size at which this appliance can operate effectively The colour of the air The air quality sensor is dirty Clean the air quality sensor see quality light ring and the chapter Cleaning air quality light always stays the same There is not enough ventilation in the room Open a window to improve the air circulation need cleaner air because You can change the air quality sensor sensitivity see chapter Using the have an allergy appliance to make the appliance clean the air even better The appliance Is extra You haven
Download Pdf Manuals
Related Search