Raw International PT1 flat panel wall mount
Contents
1. the screws on the top of the front plates fig 5 overleaf using a screw driver Now fully tighten the fixing on the tilt mechanism 3 Engaging Plasma with the wall Lift the display minimum 2 people with front plates attached so that the bars engage with the angled slots on the wall mounting plate fig 6 overleaf the screen is now safely suspended tr steel fixings i i i i apts AN steel washer front plates screen2. 4 Security Once the screen is safely suspended please tighten the bolts on the bottom right and left corner of the bracket using a screwdriver DO NOT OVER TIGHT plate to ensure the screen cannot be lifted from the screw driver EN This engages the front plates to the wall mounting wall fig 7 screen bracket screw driver 5 Adjusting the tilt mechanism Now that the screen is safely suspended on the wall using an allen key loosen the fixing on the tilt mechanism fig 8 Once you have chosen your desired tilt angle tighten the fixing on the tilt mechanism once again allen key PT1 CONSULT AUTHORISED SERVICE PERSONNEL FOR THE INSTALLATION OF THIS UNIT INSTRUCTIONS l N STR U CTI O N MUST BE FOLLOWED PRECISELY FOR SAFE AND STABLE INSTALLATION RAW INTERNATIONAL ARE M AN U AL NOT LIABLE FOR ANY DAMAGE OR INJURY CAUSED BY MISHANDLING OR IMPROPER INSTALLATION List of components Spacers M4x20mm x 4 M5x20mm x 4 M6x20m x 4 M8x20mm x 4 17x8 3x5 x 4 M4xX600mm x 4 M5x55mm x 4 M6x55 x 4 M8x55mm x 4 17x8 3x10 x 4 38mm hex key x 1 M5x75mm 4 5mm hex key x 1 M8x75mm x 4 17x8 3x20 x 4 4mm hex key x 1 6mm hex key x 1 17x8 3x80 x 4 17x8 3x40 x 4 INSTALLATION PLEASE READ CAREFULLY
3. INSTALLATION OF THIS UNIT SHOULD ONLY BE CARRIED OUT BY QUALIFIED TECHNICIANS INSTALL IN AN APPROPRIATE LOCATION ONLY AFTER CHECKING WALL STRUCTURE AND DURABILITY FOR ACCIDENT PREVENTION CONSULT A QUALIFIED BUILDER IF IN ANY DOUBT AS TO STRUCTURAL INTEGRITY OF WALL 1 Mounting wall plate Remove security screw from bottom of bracket and detach front plate fig 3 Mount wall plate fig 1 on wall in desired position using screws bolts suitable to construction of the wall If in any doubt please consult a qualified builder Attach screws bolts through as many holes slots as possible There are a total of 22 fixing holes on the back plate however the minimum amount of fixings that Raw International recommend is six If in any doubt as to strength of fixings please consult a qualified builder 2 Attaching front plates to the plasma screen Firstly loosen the fixing which controls the tilt mechanism on the front plate fig 2 This will allow clear access to the front plate fixing holes which will be used to attach the from plate to the screen Place the screen face down on soft cloth to prevent damage on a flat surface The fixings you use is dependent on the make and model of your screen There are different sets of fixings supplied with the bracket Only ONE set of fixings will be required In order to ascertain which set of fixings will be required screw fixings in the back of the screen before attempting to attac
4. h front plates Only ONE set of fixings will be of the correct diameter for your screen Mounting holes slots th th di th It is important that the front plates are fixed as centrally as possible to screen To help achieve is there is a 2mm hole in the centre of each of e front plates Line this hole up so it is equal stance between the top and bottom fixings on e back of the screen fig 3 Once it is lined allen key E a o fe fe fe o o Y a p dop e o o r o fe 2mm i t hole equal distance to 2mm hole j 9 P security igi j screw 74 A fixings holes on back of screen D po LE ze up the nearest fixing hole on the front plates to the top fixing on the plasma screen are the ones hat should be fixed first fig 4 using appropriate screws washers isolators spacers Then fix he bottom two fixings through the slots using appropriate screws washers isolators spacers Please use an Allen key to tighten all four fixings Only use isolators if back of screen is not flush with the front plates Ensure front plates are situated in a centralised horizontal position tighten
Download Pdf Manuals
Related Search