Home

Zebra SAC5070-800CR mobile device charger

1. Improper battery use may result in a fire explosion or other hazard To charge the mobile device battery the battery and charger temperatures must be between 32 F and 104 F 0 C and 40 C Do not use incompatible batteries and chargers Use of an incompatible battery or charger may present a risk of fire explosion leakage or other hazard If you have any questions about the compatibility of a battery or a charger contact Motorola Enterprise Mobility support Do not disassemble or open crush bend or deform puncture or shred e Severe impact from dropping any battery operated device on a hard surface could cause the battery to overheat Do not short circuit a battery or allow metallic or conductive objects to contact the battery terminals Quick Reference Guide 13 Do not modify or remanufacture attempt to insert foreign objects into the battery immerse or expose to water or other liquids or expose to fire explosion or other hazard Do not leave or store the equipment in or near areas that might get very hot such as in a parked vehicle or near a radiator or other heat source Do not place battery into a microwave oven or dryer e Battery usage by children should be supervised e Please follow local regulations to promptly dispose of used re chargeable batteries Do not dispose of batteries in fire Seek medical advice immediately if a battery has been swallowed Inthe event of a bat
2. 3 Wipe the metal contacts with the damp swab 10 SAC5070 8 Bay Battery Charger Troubleshooting The Power LED does not light Make sure the Power plug of Power Supply Unit is plugged into a wall outlet and the connector on the end of the Power Supply Cable is snapped in the Charger s power connector e Plug the Power plug of Power Supply Unit into another outlet Replace Power Supply Unit e Contact service representative The battery takes too long to recharge Ensure that room battery temperatures are within charging range 32 F to 104 F 0 C to 40 C e Clean the contacts on the battery Try another battery to make sure the Charger functions properly If the charge time is more than 4 hours the Charge Status LED flashes red green e Contact service representative LED flashes Red Green e Remove and re insert the battery into the charging bay e Check for dirt on battery charging contacts and or charging bay contacts e Replace battery with a new one e Call service representative Regulatory Information This device is approved under the Enterprise Mobility business of Motorola Inc Motorola This guide applies to Model Number SAC5070 All Motorola devices are designed to be compliant with rules and regulations in locations they are sold and will be labeled as required All Motorola devices are designed to be compliant with rules and regulations in locations they are sold and will be lab
3. Hands free Imager and provides a quick way to recharge the Lithium ion batteries that provide power for the RS507 Hands Free Imager One charger can hold up to eight batteries at a time The 8 Bay Battery Charger supports both standard and extended capacity batteries The Charger may only be used indoors About this Guide This guide provides basic information on the following topics e Parts of the Charger on page 4 e Installation on page 5 Inserting the Imager Battery in the Charger on page 7 Battery Age Test on page 8 Maintaining the Charger on page 9 Troubleshooting on page 10 e Regulatory Information on page 10 Wall mount template on page 17 Unpacking the Charger After opening the shipping box inspect the contents You should have received the following are 8 Bay Battery Power AC Line Quick Start Model Description Charger supply Cord Guide SAC5070 800CR USA model x x x x SAC5070 801CR International x x x model For AC line cord contact the Motorola representative in your country Inspect the equipment for damage If you are missing any equipment or if you find any damaged equipment contact Motorola Enterprise Mobility Support immediately 4 SAC5070 8 Bay Battery Charger Parts of the Charger Charger Front RS507 Imager Rest Compartment Batteries Age Test Button Charge Status LED Charging Bay Asset Control Label M4 Screw Inserts X4 Ch
4. http www motorola com MOTOROLA and the Stylized M Logo and Symbol and the Symbol logo are registered in the U S Patent and Trademark Office All other product or service names are the property of their registered owners Motorola Inc 2009 UD 72 115989 01 Revision B October 2009
5. radio TV technician for help 14 SAC5070 8 Bay Battery Charger Radio Frequency Interference Requirements Canada This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada CE Marking and European Economic Area EEA Statement of Compliance Motorola hereby declares that this device is in compliance with all the applicable Directives 2004 108 EC and 2006 95 EC A Declaration of Conformity may be obtained from www motorola com enterprisemobility doc Japan VCCI Voluntary Control Council for Interference Class B ITE HEH ts PAE j tPFvUY Pe NARRAN E BE gt lt This is a Class B product based on the standard of the Voluntary Control Council for Interference from Information Technology Equipment VCCI If this is used near a radio or television receiver in a domestic environment it may cause radio interference Install and use the equipment according to the instruction manual Korea Warning Statement for Class B ITE ASS ASA OLE 2 7171 ol JIVE 2114322 SAT YFSHS E TI7 10121 FAAIMOUME Se SE AMON ASS Vale Class User s Guide B class As this equipment has obtained EMC registration for household use it can be used in any area including residential areas Quick Reference Guide 15 X Waste Electrical and Electronic Equipment WEEE English For EU Customers All products at the end of their life mus
6. SAC5070 8 Bay Battery Charger Quick Reference Guide 2 SAC5070 8 Bay Battery Charger 2009 MOTOROLA INC All rights reserved Motorola reserves the right to make changes to any product to improve reliability function or design Motorola does not assume any product liability arising out of or in connection with the application or use of any product circuit or application described herein No license is granted either expressly or by implication estoppel or otherwise under any patent right or patent covering or relating to any combination system apparatus machine material method or process in which Motorola products might be used An implied license exists only for equipment circuits and subsystems contained in Motorola products MOTOROLA and the Stylized M Logo are registered trademarks of Motorola Inc Other product names mentioned in this manual may be trademarks or registered trademarks of their respective companies and are hereby acknowledged Motorola Inc One Motorola Plaza Holtsville N Y 11742 1300 www motorola com enterprisemobility Warranty For the complete Motorola hardware product warranty statement go to www motorola com enterprisemobility warranty Patents This product is covered by one or more patents For patent information go to www motorola com enterprisemobility patents Quick Reference Guide 3 Introduction The SAC5070 8 Bay Battery Charger is an accessory for the RS507
7. U ban v s rl knak Minden t nkrement term ket a Motorola v llalathoz kell eljuttatni jrahasznos t s c lj b l A term k visszajuttatasanak m dj val kapcsolatos tudnival k rt l togasson el a www motorola com recycling weee weboldalra Malti G al klijenti fl UE il prodotti kollha li jkunu waslu fl a ar tal ajja ta l u u tag hom iridu ji u rritornati g and Motorola g ar ri ikla G al aktar tag rif dwar kif g andek tirritorna l prodott jekk jog bok ur http www symbol com environmental_compliance Nederlands Voor klanten in de EU alle producten dienen aan het einde van hun levensduur naar Motorola te worden teruggezonden voor recycling Raadpleeg www motorola com recycling weee voor meer informatie over het terugzenden van producten Polski Klienci z obszaru Unii Europejskiej Produkty wycofane z eksploatacji nale y zwr ci do firmy Motorola w celu ich utylizacji Informacje na temat zwrotu produkt w znajduj si na stronie internetowej http www symbol com environmental_compliance Portugu s Para clientes da UE todos os produtos no fim de vida devem ser devolvidos Motorola para reciclagem Para obter informa es sobre como devolver o produto visite www motorola com recycling weee Rom nesc Pentru clien ii din UE Toate produsele la sf r itul duratei lor de func ionare trebuie returnate la Motorola pentru reciclare Pentru informa ii despre returnarea produsului ac
8. arger Battery Information Motorola rechargeable batteries are designed and constructed to the highest standards within the industry However there are limitations to how long a battery can operate or be stored before needing replacement Many factors affect the actual life cycle of a battery such as heat cold harsh environmental conditions and severe drops When batteries are stored over six 6 months some irreversible deterioration in overall battery quality may occur Store batteries at half of full charge in a dry cool place removed from the equipment to prevent loss of capacity rusting of metallic parts and electrolyte leakage When storing batteries for one year or longer the charge level should be verified at least once a year and charged to half of full charge Replace the battery when a significant loss of run time is detected Standard warranty period for all Motorola batteries is 3 months regardless if the battery was purchased separately or included as part of the mobile computer or bar code scanner For more information on Motorola batteries please visit http mysymbolcare symbol com battery batbasics1 html Battery Safety Guidelines The area in which the units are charged should be clear of debris and combustible materials or chemicals Particular care should be taken where the device is charged in a non commercial environment e Follow battery usage storage and charging guidelines found in the user s guide
9. arger Back Screws not Included Wall Mount Hole X4 Q A SS Power Supply Cable Duct M4 Screw Inserts X4 Screws not Included Power Supply Cable Duct Service Port Door Do not open for service use only Power Supply Connector Quick Reference Guide 5 Installation Tabletop Shelf Set Up To set the Charger on a tabletop or shelf 1 Place the Charger and the Power Supply Unit on a tabletop or shelf NOTE When required use the screw inserts at the back and base to secure the Charger to the tabletop or shelf surface See Figure on page 4 N Connect the Power Supply Cable to the power connector on the back of the Charger Use the Power Supply Cable Duct on the back of the Charger to route the Power Supply Cable to the left or right side of the Charger w A Connect the AC plug of the AC Power Cord to a standard electrical outlet 100 240 VAC 50 60 Hz Outlet Power Supply Cable Power Supply Unit Power Supply Cable Duct Wall Mount WARNING For safe mounting it is essential to use wall anchors appropriate to the wall type i e plaster drywall concrete etc Mount to wood studs whenever possible To mount the Charger on a wall 1 Use the wall mount template drawing on page 17 to mark the screw location on the wall 6 SAC5070 8 Bay Battery Charger 2 Use four screws to mount the Charger to a wall Ensure to use additional wall mounting hardware as needed for sa
10. cesati www motorola com recycling weee Slovenski Za kupce v EU vsi izdelki se morajo po poteku ivljenjske dobe vrniti podjetju Motorola za recikla o Za informacije o vra ilu izdelka obiS ite www motorola com recycling weee Sloven ina Pre z kazn kov z kraj n EU V etky v robky musia by po uplynut doby ich ivotnosti vr ten spolo nosti Motorola na recykl ciu Bli ie inform cie o vr ten v robkov n jdete na http www symbol com environmental_compliance Suomi Asiakkaat Euroopan unionin alueella Kaikki tuotteet on palautettava kierr tett v ksi Motorola yhti n kun tuotetta ei en k ytet Lis tietoja tuotteen palauttamisesta on osoitteessa www motorola com recycling weee Svenska F r kunder inom EU Alla produkter som uppn tt sin livsl ngd m ste returneras till Motorola f r tervinning Information om hur du returnerar produkten finns p www motorola com recycling weee Quick Reference Guide Wall Mount Template Service Information If you have a problem using the equipment contact your facility s Technical or Systems Support If there is a problem with the equipment they will contact the Motorola Enterprise Mobility Support at www motorola com enterprisemobility support For the latest version of this guide go to www motorola com enterprisemobility manuals Q MOTOROLA Motorola Inc One Motorola Plaza Holtsville New York 11742 USA 1 800 927 9626
11. eled as required Local language translations are available at the following web site www motorola com enterprisemobility support Quick Reference Guide 11 CAUTION Any changes or modifications to Motorola equipment not expressly approved by Motorola could void the user s authority to operate the equipment For use only with Motorola approved and UL Listed mobile computers Motorola approved and UL Listed accessories and or Motorola approved and UL Listed Recognized batteries Do NOT attempt to charge damp wet mobile computers or batteries All components must be dry before connecting to an external power source Charger Labeling Charger ID Label Regulatory Label Regulatory Information Power Supply Use only a Motorola approved power supply output rated at 12 VDC and minimum 4 17 A The power supply shall be listed to UL CSA 60950 1 and certified to IEC60950 1 and EN60950 1 with SELV outputs Use of alternative power supply will invalidate any approval given to this device and may be dangerous Taiwan Recycling ca EPA Environmental Protection Administration requires dry Us battery producing or importing firms in accordance with Article EEE 15 of the Waste Disposal Act are required to indicate the recycling marks on the batteries used in sales giveaway or promotion Contact a qualified Taiwanese recycler for proper battery disposal 12 SAC5070 8 Bay Battery Ch
12. fe mounting according to the wall type 3 Connect the power supply cable to the power connector on the back of the Charger See Figure on page 5 4 Use the Power Supply Cable Duct on the back of the Charger to route the Power Supply Cable to the left or right side of the Charger 5 Place the Power Supply Unit on a shelf or tabletop 6 Connect the AC plug of the AC Power Cord to a standard electrical outlet 5mm 0 19 inches gt NOTE Use Wal mount template on page 17 220 mm 8 6 inches A ed a ae N 10 mm e 0 39 inches TR e f 8 38 mm 1 5 inches Quick Reference Guide 7 Inserting the Imager Battery in the Charger The Charger supports both standard and extended capacity batterys Charge the Battery CAUTION Only Lithium ion batteries that have been designed for use with the RS507 Hands free Imager can be recharged by the Charger Do not attempt to recharge other types of rechargeable batteries or any type of batteries Doing so could destroy those batteries and damage the Charger NOTE Batteries should be charged within the 32 F 0 C and 104 F 40 C ambient temperature range To charge the battery s 1 Insert the battery s into the 8 Bay Battery Charger so that the contacts of the battery are first to enter facing down gently DO NOT USE EXCESSIVE FORCE 2 The 8 Bay Battery Charger starts to charge automatically On each bay the flashing amber Charge Status LED See F
13. igure on page 4 indicates the charge status 8 SAC5070 8 Bay Battery Charger A full charge of a depleted battery takes up to four hours The Charge Status LED lights solid amber when the battery is fully charged Battery Age Test The battery age test checks the battery capacity when fully charged A worn out battery is considered to have less than 80 of its nominal capacity The battery test is simultaneously performed for all batteries inserted into the charger It is recommended to perform battery age testing once a month The age test may take up to 16 hours NOTE A battery removed during test and re inserted is excluded from the test but continues normal charging To test the battery s 1 Insert one or more batteries into Charging Bay s 2 Press and hold the Test Button for approximately 3 seconds until the Charge Status LED of each active bay flashes green 3 Refer to the table below when the indication of the Charge Status LED changes Charge Status LED The Charge Status LEDs show the charge status of each Charging Bay LED Indication Status Flashing amber Charging in progress Solid amber Charging is completed Flashing green Battery age testing in progress Flashing red green Defective battery or error in charging re insert the battery into the bay Solid green Battery age test and charge are completed Battery is good Solid red Battery age test and charge are completed Battery ca
14. pacity is marginal Flashing red Battery age test and charge are completed Battery is worn out Quick Reference Guide 9 Maintaining the Charger The Charger is well constructed and durable however it is a precision electronic device and must be treated as such Follow the procedures in this section to ensure reliable service Operating Conditions for the Charger The Charger is designed to operate in environments that are normally free of dust dirt and moisture It can be operated at temperatures between 32 F 0 C and 104 F 40 C Handling the Charger Do not attempt to open the Charger No user serviceable parts are inside e Charge only Lithium ion batteries that have been designed for use in a RS507 Hans free Imager Do not attempt to recharge other types of rechargeable batteries or any type of primary batteries Do not place objects other than RS507 Hans free Imager batteries inside the Charger e Protect the Charger from excessive heat cold moisture and harsh dirty environments Do not leave the Charger where moisture will condense on it Cleaning A CAUTION Do not pour spray or spill any liquid on the Charger The gold plated battery contacts do not tarnish or oxidize No maintenance should be needed If the contacts need to be cleaned 1 Remove power from the Charger 2 Wet the tip of a cotton swab with isopropyl alcohol and squeeze the excess alcohol from the swab
15. t be returned to Motorola for recycling For information on how to return product please go to www motorola com recycling weee Bulgarish 3a knueHtu or EC Crea kpaa Ha none3HuaA NM KUBOT BCNYKN npoayktn TpABBa Ja ce BpbliaT Ha Motorola 3a peuunknupaHe 3a uHpopmauna OTHOCHO BpbuaHeTo Ha MpoAyKTM MONA OTUAETE Ha anpec www motorola com recycling weee e tina Pro z kazn ky z EU V echny produkty je nutn po skon en jejich ivotnosti vr tit spole nosti Motorola k recyklaci Informace o zp sobu vr cen produktu najdete na webov str nce http www symbol com environmental_compliance Dansk Til kunder i EU Alle produkter skal returneres til Motorola til recirkulering n r de er udtjent L s oplysningerne om returnering af produkter p www motorola com recycling weee Deutsch F r Kunden innerhalb der EU Alle Produkte m ssen am Ende ihrer Lebensdauer zum Recycling an Motorola zur ckgesandt werden Informationen zur R cksendung von Produkten finden Sie unter www motorola com recycling weee Eesti EL klientidele k ik tooted tuleb nende eluea l ppedes tagastada taaskasutamise eesm rgil Motorola ile Lisainformatsiooni saamiseks toote tagastamise kohta k lastage palun aadressi www motorola com recycling weee Espa ol Para clientes en la Uni n Europea todos los productos deber n entregarse a Motorola al final de su ciclo de vida para que sean reciclados Si desea m s informaci n sobre c mo devolver
16. tery leak do not allow the liquid to come in contact with the skin or eyes If contact has been made wash the affected area with large amounts of water and seek medical advice If you suspect damage to your equipment or battery contact Motorola Enterprise Mobility support to arrange for inspection Radio Frequency Interference Requirements FCC Note This equipment has been tested and found to comply FE testearo compy With the limits for a Class B digital device pursuant to Part 15 with FCC Standards Of the FCC rules These limits are designed to provide E E e reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected e Consult the dealer or an experienced
17. un producto visite www motorola com recycling weee EAAnvika Pia treAdtes otnv E E O a Ta Trpoidvta oTo T MOG TNG SIapKEIAG W TOUG TTp TTEL VA ETTIOTPEPOVTA OTHV Motorola yia avak kAwOn Tia TrepiogoTEepEs TANPOPOpiEG OXETIK HE TNV ETTIOTPOMN EVOG TIPOIOVTOG ETTIOKEPOEiTE TH DiE BUVON http www symbol com environmental_compliance oto Aia iktuo Francais Clients de l Union Europ enne Tous les produits en fin de cycle de vie doivent tre retourn s Motorola pour recyclage Pour de plus amples informations sur le retour de produits consultez www motorola com recycling weee Italiano per i clienti dell UE tutti i prodotti che sono giunti al termine del rispettivo ciclo di vita devono essere restituiti a Motorola al fine di consentirne il riciclaggio Per informazioni sulle modalit di restituzione visitare il seguente sito Web www motorola com recycling weee 16 SAC5070 8 Bay Battery Charger Latvie u ES klientiem visi produkti p c to kalpo anas m a beig m ir j nog d atpaka Symbol otrreiz jai p rstr dei Lai ieg tu inform ciju par produktu nog d anu Motorola l dzu skatiet http www symbol com environmental_compliance Lietuvi ES vartotojams visi gaminiai pasibaigus j eksploatacijos laikui turi b ti gr inti utilizuoti kompanij Motorola Daugiau informacijos kaip gr inti gaminj rasite http www symbol com environmental_compliance Magyar Az E

Zebra SAC5070-800CR mobile device charger

Contents

Download Pdf Manuals

Related Search

Related Contents