Home

SCOTT LSX 10

image

Contents

1. for resetting in standby mode Then repeat the pairing operation mentioned above MAINTENANCE Care and maintenance To clean the casing unplug the unit and wipe off dust and stains with a soft damp cloth Do not use benzene thinner or similar chemicals to clean the casing note that electrical products should not be disposed of with household waste Find out where your nearest recycling centre is Consult your focal authority or retailer for more details Waste Electrical Electronic Equipment Directive TROUBLESHOOTING GUIDE Problems Recommendations 1 The LED light with 1 1 Do pairing speaker does not work 1 2 Do not use your external dimmer control properly TECHNICAL SPECIFICATIONS LED light with speaker Power source If at any time in the future you want to dispose of this product please AC 100 240V 50 60Hz Power consumption Standby power consumption Dimensions Weight Light type LED E27 screw Lighting power 5 W Light life 30000 Hours Speaker 2 25 4 Ohm Output power Speaker 10 W r m s 20 W Light speaker lt 1W 138 H x 85 Dia mm 0 4 Kg Note Due to continuing improvements the technical specifications are subject to change without notice GB 3
2. ENTS PRECAUTIONS TABLE OF CONTENTS BOX CONTENTS LOCATION OF CONTROLS POWER SUPPLY AND INSTALLATION BASIC OPERATION MAINTENANCE TROUBLESHOOTING GUIDE TECHNICAL SPECIFICATIONS WWWNNNN GB 1 BOX CONTENTS 1 LED Light with speaker 3 Instruction manual 2 Pin for pairing LOCATION OF CONTROLS 1 LED light with speaker 1 E27 screw 2 LED light 3 Pair button 4 Standby LED 5 Speaker POWER SUPPLY AND INSTALLATION LED light with speaker Make sure the power source is switched off before installation Screw the LED light with speaker to an E27 socket with an AC 100 240V 50 60Hz power source Note Do not use your external dimmer control that may cause the unit malfunction To dim the light press the button repeatedly BASIC OPERATION Note This LED light with speaker must be used with the docking station SCOTT model no iDXS 10L or iXSW 50 Refer to the instruction manual of the docking station for detail operation Standby On mode N Device Standb On LED light with Standby LED On Off speaker LED light Off On PAIRING Note Make sure that the LED light with speaker is powered properly Refer to the manual of your iDXS 10 L or iXSW 50 system for more information about pairing Pairing is to ensure your LED light with speaker can receive RF transmission correctly from the docking station 1 If you want to pair this new light in an existing group one station 2 lights to get stereo s
3. HSCOTT MODEL NO LSX 10 WIRELESS LED LIGHT WITH SPEAKER Instruction Manual PRECAUTIONS Follow the instructions below to ensure the product is used safely and correctly PLACEMENT Do not use the unit in places which are extremely hot cold dusty or humid Do not restrict the airflow around the unit by placing it in a place with poor ventilation Do not place the unit close to heat sources Use the apparatus only in moderate climates Do not expose the unit to rain or splash with water Do not place objects filled with liquids such as vases the unit AC VOLTAGE Before use check that the rated voltage of your unit matches your local voltage CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with an ATTENTION To reduce the The exclamation mark arrowhead symbol within risk of electric shock do not within a triangle is a a triangle is a warning remove the cover There are no warning sign alerting the sign alerting the user to user serviceable parts inside user to the presence of the presence of the unit Refer all servicing to important instructions dangerous voltage qualified personnel accompanying the inside the unit product Congratulations on your purchase of this additional wireless light with loud speaker that we hope will fully meet your requirements It will allow you to improve iDXS 10L iXSW 50 system TABLE OF CONT
4. ound you have to reset the pairing first when the docking station is in standby mode use the piece supplied to press and hold the PAIR button of the docking station for more than 10 seconds until the source LEDS at the top of the docking station flash The station then goes back to standby mode 2 Press the PAIR buttons briefly at the bottom of the docking station first and then the other devices within one minute All the standby LEDs will blink rapidly until the pairing is successful in about one minute and the source LEDS at the top of the docking station will flash for few seconds 3 For pairing the next group repeat above step 2 GB 2 After pairing turn on the docking station and use the number buttons 1 8 ALL on the remote control of docking station to select the group of your choice and use the or button to turn on off the speaker sound or adjust the light of the LED light Note e For pairing the docking station must be in standby mode and the devices must be switched on e The group number is assigned according to the sequence of pairing Number 1 will be assigned to the first paired group e First and second paired speakers in the same group are set to left and right channels respectively e Each group can contain maximum two sets LED light with speaker e In case pairing is not successful use a sharp object to press and hold the PAIR button more than 10 seconds at the bottom of the docking station

Download Pdf Manuals

image

Related Search

Related Contents

Targus SafePORT  Untitled - G  Simplified Operating Instructions – T105-C / T108-C / T106  Trust Linea  Manuale installatore  Pelco CM9700UTP32A Switch User Manual    L`Espace Info Énergie, nouveau    ScanVision取扱説明書  

Copyright © All rights reserved.
Failed to retrieve file