JBL SCS-200.5BK
Contents
1. Receiver Left Front Center Dao Left Surround Left Surround O OPERATION Move the Master Power switch marked Power to the e On position to use the SUB200 subwoofer If you will be away from home for an extended period of time or if the subwoofer will not be used switch the Master Power switch to the Off position SUBWOOFER LEVEL GO TEEGEE m lt m WARNING FOR CC FISK OF FRE REP AVERTISSEMENT VOLUME Subwoofer Level ZOD Subwoofer Level MIN MAX Volume may be adjusted using the Subwoofer Level control as shown TROUBLESHOOTING If there is no sound from any of the speakers e Check that receiver ampli fier is on and a source is playing e Check that the powered subwoofer is plugged in and its Power switch is switched on e position e Check all wires and con nections between receiver amplifier and speakers Make sure all wires are con nected Make sure none of the speaker wires are frayed cut or punctured or touching each other e Review proper operation of your receiver amplifier If there is no sound coming from one speaker e Check the Balance control on your receiver amplifier e Check all wires and con nections between receiver amplifier and speakers Make sure all wires are con nected Make sure none of the speaker wires are2. Do not defeat the safety purpose of the polarized or grounding type plug A polarized plug has two blades with one wider than the other A ground ing type plug has two blades and a third grounding prong The wide blade or the third prong are provided for your safety If the provided plug does not fit into your outlet consult an electrician for replacement of the obsolete outlet 10 Protect the power cord from being walked on or pinched particularly at plugs convenience receptacles and the point where they exit from the apparatus 11 Only use attachments accessories specified by the manufacturer 12 Use only with the cart stand tri pod bracket or table specified by the manufacturer or sold with the appa ratus When a cart is used use caution when moving the cart apparatus combi nation to avoid injury from tip over 2 13 Unplug this apparatus during light ning storms or when unused for long periods of time 14 Refer all servicing to qualified service personnel Servicing is required when the apparatus has been damaged in any way such as power supply cord or plug is dam aged liquid has been spilled or objects have fallen into the appara tus the apparatus has been exposed to rain or moisture does not operate normally or has been dropped 15 Do not use attachments not recommended by the product manufacturer as they may cause hazards 16 This product should be operated only from the type
3. frayed cut or punctured or touching each other In Dolby Digital or DTS modes make sure that the receiver processor is config ured so that the speaker in question is enabled e Turn off all electronics and switch the speaker in question with one of the other speakers that are working correctly Turn everything back on and determine whether the problem has followed the speaker or has remained in the same channel If the problem is in the same channel the source of the problem is most likely with your receiver or amplifier and you should consult the owner s manual for that product for further informa tion If the problem has fol lowed the speaker consult your dealer for further assis tance or if that is not possi ble visit www jbl com If there is no sound from the center speaker e Check all wires and con nections between receiver amplifier and speaker Make sure all wires are connected Make sure none of the speaker wires are frayed cut or punctured or touch ing each other e If your receiver processor is set in Dolby Pro Logic mode make sure the center speaker is notin phantom mode e If your receiver processor is set in one of the Dolby Digital or DTS modes make sure the receiver processor is configured so that the center speaker is enabled If the system plays at low volumes but shuts off as volume is increased e Check all wires and con nections between receiver amplifier and spea
4. outer edge of the Molded Nut Step 2 Firmly grasp the Ball and Shaft and pull it straight out of the Attach ment Plate Avoid leaning it to the side for leverage as this may break off a tab 6 Step 3 Slide the Molded Nut onto the Ball and Shaft with the threaded opening facing the ball Thread the Metal Nut all the way onto the Ball and Shaft with the star washer side away from the ball Refer to the exploded drawing for the proper orientation of these parts Step 5 Tighten the Metal Nut with the star washer side between the Nut and the back of the Satellite Speaker using large needle nose pliers until it is firmly seated against the back of the Speaker and has locked the Ball and Shaft and the Speaker together Note that once the Metal Nut is fully tightened it may embed some marks on the back of the Satellite Speaker However these marks will be covered by the Metal Nut Step 6 Mount the Attachment Plate into a wood stud on the wall using four 10 pan head wood screws at least Step 4 Screw the Ball and Shaft into the Threaded Insert on the back of the Satellite Speaker until it is fully seated in the Threaded Insert but do not tighten as you might dislodge the Threaded Insert Such damage would not be covered under the warranty one inch long not supplied Make sure that all four screws are driven into the stud and not in
5. S CENTER CHANNEL SPEAKER SUBWOOFER 0 2 ft o o 6m 1 SURROUND SPEAKERS Taf G T m The front speakers should be placed the same distance from each other as they are from the listening position They should be placed at about the same height from the floor as the listeners ears will be or they may be angled toward the listeners The center channel speaker should be placed directly above or below the televi sion and no more than two feet above or below the tweeters of the left and right speakers It is often con venient to set the center speaker on top of the tele vision set as shown in the drawing The surround speakers should be placed slightly behind the listening position and ideally should face each other and be at a level higher than the listeners ears If that is not possible they may be placed on a wall behind the listening position facing forward Additional satellites may be purchased separately for use in 6 1 or 7 1 channel systems MOUNTING OPTIONS SATELLITES AND SURROUNDS On shelves 4 Generally it is best to aim all of the speakers except the subwoofer toward the listen ing position at about ear level height The low frequency material reproduced by the subwo
6. a 2 W 2 O a Z 5 E E gt a SPEAKERS OWNER S GUIDE READ FIRST Important Safety Precautions CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION To reduce the risk of electric shock do not remove cover or back No user serviceable parts inside Refer servicing to qualified service personnel CAUTION To prevent electric shock do not use this polarized plug with an extension cord receptacle or other outlet unless the blades can be fully inserted to prevent blade exposure The lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance servicing instructions in the literature accompanying the appliance 1 Read these instructions 2 Keep these instructions 3 Heed all warnings 4 Follow all instructions 5 Do not use this apparatus near water 6 Clean only with a dry cloth 7 Do not block any ventilation open ings Install in accordance with the manufacturer s instructions 8 Do not install near any heat sources such as radiators heat registers stoves or other apparatus including amplifiers that produce heat 9
7. e level output Left Front R Left Surround Back Surround Left Center Subwoofer Line Level In L Receiver Subwoofer Center Surround Back Right Connect this jack to the LFE output or subwoofer output on your receiver or amplifier Connect each speaker to the corresponding speaker terminals on your receiver or amplifier Make sure that you have configured your surround sound processor for Subwoofer On The front left front right center and surround speakers should all be set to Small If your receiver allows you to set the crossover frequency between the subwoofer and the main speakers select 120Hz or the setting that is the closest frequency below it NON DIGITAL LINE LEVEL Use RCA type interconnects to connect the line level subwoofer outputs on your receiver or amplifier to the line level inputs on the sub woofer IMPORTANT Do not use the LFE input on the sub woofer with Dolby Pro Logic processors Right Front Right Front Surround Right Left Surround Back Surround Left Surround Back Right d Right urroun NOTE If your receiver or amplifier has only one sub woofer output jack then you will need to use a Y connec tor not included Plug the male end of the Y connector into your receiver or ampli fier s subwoofer output jack and connect each of th
8. e two female ends to separate RCA type interconnects Finally plug the RCA type interconnects into the line level inputs on the sub woofer Connect each speaker to the corresponding speaker terminals on your receiver or amplifier Make sure your receiver or processor is correctly con figured to indicate that the subwoofer is On Note for advanced users lf your receiver processor has a built in low pass crossover filter for the subwoofer out put you may use the LFE input to bypass the sub woofer s internal crossover DOLBY PRO LOGIC NON DIGITAL SPEAKER LEVEL Use this installation method for Dolby Pro Logic applica tions not Dolby Digital DTS or other digital processing where the receiver processor does not have a subwoofer output or a volume controlled preamp line level output Connect your receiver or amplifier s front left and right speaker terminals to the left and right terminals on the subwoofer that are marked Speaker Level In Connect the left and right terminals on the subwoofer that are marked Speaker Level Out to the corresponding termi nals on the back of your front left and right speakers Connect your receiver or amplifier s center surround and surround back speaker terminals to the correspon ding terminals on the back of your center and surround speakers Left Front Right Front Center QO Subwoofer remem mm gt gt m
9. er push objects of any kind into this product through openings as they may touch dangerous voltage points or short out parts that could result in a fire or electric shock Never spill liquid of any kind on the product 21 Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards Refer all servicing to qualified service personnel 22 When replacement parts are required be sure the service tech nician has used replacement parts specified by the manufacturer or that have the same characteristics as the original part Unauthorized substitu tions may result in fire electric shock or other hazards 23 Upon completion of any service or repairs to this product ask the service technician to perform safety checks to determine that the product is in proper operating condition 24 The product should be mounted to a wall or ceiling only as recom mended by the manufacturer Antenna Lead in Wire Ground Clamp Antenna Discharge Unit NEC Section 810 20 Grounding Conductors NEC Section 810 21 Electric Service Equipment Ground Clamps Power Service Grounding Electrode System oe NEC Art 250 Part H THANK YOU FOR CHOOSING JBL For more than 60 years JBL has been involved in every aspect of music and film recording and reproduction from live performances to the recordings you play in your home car or office We re confident that the JBL syste
10. kers Make sure all wires are con nected Make sure none of the speaker wires are frayed cut or punctured or touching each other e If more than one pair of main speakers is being used check the minimum imped ance requirements of your receiver amplifier If there is low or no bass output e Make sure the connections to the left and right Speaker Inputs have the correct polarity and e Make sure the subwoofer is plugged into an active electrical outlet and is turned on Power switch in the e position e In Dolby Digital or DTS modes make sure your receiver processor is config ured so that the subwoofer and LFE output are enabled If there is no sound from the surround speakers e Check all wires and con nections between receiver amplifier and speakers Make sure all wires are con nected Make sure none of the speaker wires are frayed cut or punctured or touching each other e Review proper operation of your receiver amplifier and its surround sound features e Make sure the movie or TV show you are watching is recorded in a surround sound mode If it is not check to see whether your receiver amplifier has other surround modes you may use e In Dolby Digital or DTS modes make sure your receiver processor is config ured so that the surround speakers are enabled e Review the operation of your DVD player and the jacket of your DVD to make sure that the DVD features the de
11. m you have chosen will provide every note of enjoy INCLUDED ment that you expected and that when you think about purchasing additional audio equipment for your home car or office you will once again choose JBL Please take a moment to register your product on our Web site at www jbl com It enables us to keep you posted on our latest advance ments and helps us to better understand our customers and build products that meet their needs and expectations JBL Incorporated Sak t ftt fd fd le gt SS One center channel speaker with shelf stand Wall mount bracket Four satellites for left right and surrounds Wall mount brackets Shelf stands Floor stand adapters Powered subwoofer Three 20 6m speaker cables for connection to front left center and right speakers or to subwoofer when speaker level connections are used see page 9 Two 40 12m speaker cables for connection from receiver to rear satellites One 15 4 6m RCA interconnect cable for connection from receiver to subwoofer s LFE input In addition there are two hardware bags included Hardware Bag A contains the metal tightening bar and screws for the shelf stands Hardware Bag B contains screws for the floor stand adapters and parts for the wall mount brackets SPEAKER PLACEMENT FRONT SPEAKER
12. of power source indicated on the marking label If you are not sure of the type of power sup ply to your home consult your prod uct dealer or local power company For products intended to operate from battery power or other sources refer to the operating instructions 17 If an outside antenna or cable system is connected to the product be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built up static charges Article 810 of the National Electrical Code ANSI NFPA 70 provides information with regard to proper grounding of the mast and supporting structure grounding of the lead in wire to an antenna discharge unit size of grounding conductors location of antenna discharge unit connection to grounding electrodes and require ments for the grounding electrode See Figure A Figure A Example of Antenna Grounding as per National Electrical Code ANSI NFPA 70 18 An outside antenna system should not be located in the vicinity of over head power lines or other electric light or power circuits or where it can fall into such power lines or cir cuits When installing an outside antenna system extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal 19 Do not overload wall outlets extension cords or integral conve nience receptacles as this can result in a risk of fire or electric shock 20 Nev
13. ofer is mostly omnidirectional and this speaker may be placed in a convenient loca tion in the room However bass reproduction will be maximized when the sub woofer is placed in a corner along the same wall as the front speakers Experiment with subwoofer placement by temporarily placing the sub woofer in the listening posi tion and moving around the room until the bass reproduc tion is best Place the sub woofer in that location On the wall Wall brackets are included On optional stands ATTACHING THE SHELF STAND TO THE SPEAKER Prepare the speaker wire as described on page 7 Thread the two conductors through the two holes in the stand bracket Make sure to pre serve the proper polarity and connections by threading the positive con ductor through the hole on the left and the negative conductor through the hole on the right looking at the front of the stand Push down on the red speaker terminal and insert the bare end of the positive wire into the hole under the red cap Release the cap and tug gently on the wire to make sure that the connection is Gently pull the slack out of the wire and screw the shelf stand onto the back of the speaker in two places as shown snug Follow the same pro cedure to connect the nega tive wire to its terminal Use the larger screw Hardware Bag A in the upper screw hole and the smaller screw Hardware Bag A in the l
14. ower screw hole MOUNTING THE SATELLITES ON OPTIONAL FLOOR STANDS Important Safety Note The supplied floor stand adapters facilitate installation with a variety of general purpose floor stands available from many manufacturers Since different stands will have different weight capacities and stability characteristics it is the customer s responsibil ity to check with the stand manufacturer or dealer to determine whether that spe cific stand is capable of han dling the weight and propor tions of these loudspeakers in a safe and stable manner JBL disclaims any liability for the selection of suitable floor stands and or correct compat ibility between the selected stand and these loudspeakers The floor stand adapters are compatible with floor stands equipped with a 1 4 20 threaded insert Prepare the speaker wire as described on page 7 Thread the two conductors through the two holes in the floor stand adapter Make sure to preserve the proper polarity and connections by threading the positive conductor through the hole on the left and the nega tive conductor through the hole on the right looking at the front of the adapter Push down on the red speaker ter minal and insert the bare end of the positive wire into the hole under the red cap Release the cap and tug gently on the wire to make sure that the connection is snug Follow the same procedure to connect the negative wire to its
15. reflex Dimensions H x W x D including feet 16 1 4 x 11 x 13 3 4 413mm x 279mm x 349mm Weight 28 Ib 12 7kg All features and specifications are subject to change without notice Dolby and Pro Logic are registered trademarks of Dolby Laboratories DTS is a registered trademark of DTS Inc PRO SOUND COMES HOME JBL Incorporated 250 Crossways Park Drive Woodbury NY 11797 8500 Balboa Boulevard Northridge CA 91329 516 255 4JBL 4525 USA only www jbl com 2006 Harman International Industries Incorporated All rights reserved JBL and Harman International are trademarks of Harman International Industries Incorporated registered in the United States and or other countries Part No 406 000 05457 E H A Harman International Company
16. sired Dolby Digital or DTS mode and that you have properly selected that mode using both the DVD player s menu and the DVD disc s menu 11 SPECIFICATIONS SCS200 5 Frequency Response 35Hz 20kHz 6dB SATELLITES Maximum Recommended Amplifier Power 100 Watts Power Handling Continuous Peak 50W 160W Nominal Impedance 8 Ohms Sensitivity 86dB 1 Watt 1 meter Frequency Response 110Hz 20kHz 6dB Tweeter 1 2 13mm Titanium laminate dome video shielded Midrange 3 75mm Driver video shielded Dimensions H x W x D not including shelf stands 7 1 4 x 4 x 3 1 2 184mm x 102mm x 89mm Weight 1 75 Ib 0 8kg CENTER Maximum Recommended Amplifier Power 100 Watts Power Handling Continuous Peak 50W 200W Nominal Impedance 8 Ohms Sensitivity 88dB 1 Watt 1 meter Frequency Response 100Hz 20kHz 6dB Tweeter 1 2 13mm Titanium laminate dome video shielded Midrange Dual 3 75mm drivers video shielded Dimensions H x W x D not including shelf stand 4 x 11 1 2 x 3 1 2 102mm x 292mm x 89mm Weight 3 Ib 1 4kg OWNER S GUIDE PRODUCT LINE SURROUND CINEMA SPEAKERS MODELS S CS200 5 DESIGN GOAL Bring the thrill of live performance and movie sound to the home environment by calling on JBL s professional engineering leadership sealed enclosure SUBWOOFER Amplifier 100 Watts RMS Frequency Response 35Hz 160Hz 6dB Woofer 8 200mm Enclosure Bass
17. terminal Gently pull the slack out of the wire and screw the adapter onto the back of the speaker in two places as shown The floor stand adapter screws may be found in Hardware Bag B Use the larger screw in the upper screw hole and the smaller screw in the lower screw hole Screw the floor stand adapter into the floor stands threaded insert until the speaker is firmly attached to the stand Back off slightly from the fully tightened position until the speaker is oriented as desired then rotate the thumbwheel at the bottom of the floor stand adapter to secure the speaker to the stand WALL MOUNTING Important Safety Note The customer is solely responsi ble for proper selection of mounting hardware not included with the speakers and for proper assembly and installation of the wall brackets including but not limited to the selection of appropriate weight bearing supports and proper use of the bracket JBL disclaims any liability for the selection of mounting hardware and or bracket installation Be sure to follow these bracket assembly and installation instructions carefully If you have any questions or doubts about your ability to correctly wall mount the speakers consult with your authorized JBL dealer or custom installer Step 1 Unscrew and remove the large Molded Nut If necessary use the supplied Metal Bar as a lever by inserting it into one of the holes in the
18. to aim the speaker to one side or the other or to tilt it up or down Although stereo imaging may be improved by aiming the front speakers toward the listening position especially for music selec tions the surround speakers are intended to provide a diffuse ambient sound that is best achieved by aiming the speakers straight out from the wall Aiming the surround speakers toward The lead of the speaker wire is noted with a stripe It is important to connect both speakers identically on the speaker to on the amplifier and on the speaker to on the amplifier Wiring out of phase results in thin sound weak bass and a poor stereo image With the advent of multi channel surround sound systems connecting all of the speakers in your system with the correct polarity remains equally important in order to preserve the proper ambience and directionality of the program material To connect the supplied speaker wires to the satellite and center speaker termi nals press the red or black plastic cap for the desired terminal insert the bare end of the wire into the hole below the cap and release the listening position may ruin the intended effect by calling too much attention to the information in those channels Step 9 Once the speaker s orientation has been final ized insert the Metal Bar into one of the holes in the outer edge of the Molded Nut and tighten the Molded Nut securel
19. to drywall If the bracket needs to be mounted in drywall the customer is responsible for selecting and using appropri ate wall anchors and screws Important Note The Metal Nut must be fully tight ened against the Satellite Speaker as described in Step 5 before beginning Step 7 in order to avoid damage to the Threaded Insert O Such damage would not be covered under the warranty Step 7 Holding the Satellite Speaker with both hands reinsert the ball portion of the Ball and Shaft into the Attachment Plate Step 8 Hand tighten the Molded Nut while posi tioning the speaker for the desired orientation If the Molded Nut is difficult to tighten by hand insert the Metal Bar into one of the SPEAKER CONNECTIONS CONNECTION TIPS A Separate and strip the ends of the speaker wire as shown The wires sup plied with the system may already be stripped and tinned for easy insertion into the speaker terminals You may need to separate the two conductors further in order to thread them through the shelf stand or floor stand adapter Speakers and elec tronics terminals have corre sponding and termi nals Most manufacturers of speakers and electronics including JBL use red to denote the terminal and black to denote the terminal holes in the outer edge of the Molded Nut and use the bar as a lever Be careful not to cross thread The swiveling ball enables you
20. y Keep the Metal Bar ina safe place in the event that you decide to adjust the speaker s orientation in the future the cap Gently tug on the wire to make sure that it is fully inserted To use the binding post speaker terminals on the subwoofer unscrew the colored collar until the pass through hole in the center post is visible under the collar Insert the bare end of the wire through this hole then screw the collar down until the connection is tight The hole in the center of each collar is intended for use with banana type connectors To comply with European CE certification these holes are blocked with plastic inserts at the point of manufacture To use banana type connectors requires the removal of the inserts Do not remove these inserts if you are using the product in an area covered by the European CE certification 7 DOLBY DIGITAL OR DTS OR OTHER DIGITAL SURROUND MODE CONNECTION RECEIVER SUBWOOFER LFE OUT LINE LFE L R f Use this installation method for Dolby Digital DTS or other digital surround processors Use the line level input jack marked LFE for the Low Frequency Effects channel DOLBY PRO LOGIC Use this installation method for Dolby Pro Logic applica tions not Dolby Digital DTS or other digital processing where the receiver proces sor is equipped with a sub woofer output or a volume controlled preamp lin
Download Pdf Manuals
Related Search