Kathrein UFS 932sw/HD+
Contents
1. Slide the cover back onto the housing until it locks in place To open it Gently press here and pull it backwards Connection and setup Connecting the receiver If you do not know the configuration of your satellite reception system contact your specialist dealer Connect the Sat IF inputs on the receiver to the satellite reception system Use coaxial cable with an F standard connector see illustration on right Conventional DiSEqC system HDMI I DOLBY A DIGITAL OPTICAL KATHREIN X3 Connect the satellite receiver HDMI or alternatively TV Scart socket and the TV set using a HDMI or Scart cable see the connection example above o L8 Connection and setup Audio connection There are two ways you can access the digital audio HDMI The stereo audio is transmitted to your TV set via the HDMI interface If your TV set also supports Dolby Digital you can also receive the Dolby Digital audio via the HDMI interface providing it is broadcast by the channel provider On this issue refer to the operating manual for your TV set SPDIF Dolby Digital output optical The SPDIF outputs are intended for the connection of a Dolby Digital system see Advanced connection example in the technical appendix2. Standard Low Oscillation Frequency LNB low frequency You only need to specify this data if your LNB type is not Universal LNB For this refer to the documentation supplied with your LNB Enter the LNB low frequency using the numeric pad or the j gt buttons High Oscillation Frequency LNB high frequency You only need to specify this data if your LNB type is not Universal LNB Enter the LNB high frequency using the numeric pad or the lt buttons 22 kHz This cannot be set and is not reguired Connection and setup LNB Power This is factory set to On but must be changed if your LNB has its own power supply In most cases the LNB power supply is provided by the receiver Test transponder TP Select the selection field TP Here you can select a transponder for checking whether your settings are correct using the signal strength bar and signal quality bar When you have completed all settings press the n green button You will automatically be shown the display for Update LCN List Continue the first installation with the Update LCN List selection LCN Logical Channel Numbering Channels are sorted according to a list held in the receiver Connection and setup DiSEqC 1 0 Antenna Configuration cy Select satellite and port satellite slot Here you can select the satellites whose signals you wish to receive Select only those satellites that are present in the s
3. accessibility In order to disconnect the unit from the mains completely the mains plug must be unplugged from the wall socket Therefore install the unit close to a mains socket and make sure this socket is accessible at all times so that you can disconnect the unit from the mains if necessary If you are away for an extended period and during thunderstorms always switch the unit off at the mains and unplug it from the socket This also applies to the other equipment connected to the unit Isolation from the cable network is also recommended Note any timer programming receiver and turn the unit on again promptly before the recording time Installation location All electronic equipment generates heat However the heating of this unit lies within the permissible range Sensitive furniture surfaces and veneers may become discoloured by the effects of constant heat over time The feet of the unit can also cause colour changes to treated furniture surfaces If necessary place the unit on a suitable stable and flat base EA O Electronic eguipment is not domestic waste it must be disposed of properly in accordance with directive 2002 96 EC OF THE EUROPEAN PARLIAMENT AND THE COUNCIL dated 27 January 2003 concerning used electrical and electronic appliances At the end of its service life take this device for disposal at a designated public collection point Spent batteries are special waste Do not thr
4. no longer responds Tuner Configuration menu and change them if necessary The batteries may be flat or Check the batteries see also inserted incorrectly into the battery compartment Inserting batteries into the remote control in these instructions Wrong time is displayed The Summertime setting is wrong An incorrect time was imported from the reception signal Check the Local Time Setting in the System Setup menu and change it if necessary Use the power switch to switch the receiver off from the current channel e g Das Erste or ZDF wait 10 seconds and then switch it back on The following channels cut out or No or bad signal appears Sport 1 Tele 5 HSE 24 and Sonnenklar TV DECT telephones operate on the same frequency as these channels Interference may occur due to inadequate level or poor shielding of cable Consult your antenna specialist Service If despite studying this operating manual you still have questions about getting started with the unit or using it correctly or if unexpected problems occur please contact your specialist dealer The Kathrein customer hotline is also at your disposal Tel 0900 1122240 0 49 EUR per minute on Deutsche Telekom AG land lines calls from mobile phones may cost more Technical appendix Advanced connection example Hi fi system Tei Penh PY e ki v Ex
5. the receiver front flap open Connection and setup Front Rear view 1 On Off operation stand by 8 LNB loop through input 2 4 character numeric display 9 LNB input 3 Channel selection button 10 Audio outputs L R cinch sockets 4 Channel selection button 11 3xCinch connections for component outputs 5 Card reader Nagravision integrated for ae WRIT HD card 12 Video output composite colour 6 Common Interface for one CI CA module 13 HDMI connection Ier Pay t carae 14 USB 2 0 port USB A connector 15 Scart socket for TV connection 16 Scart socket for VCR AUX connection 17 Optical data stream output SPDIF Sony Philips Digital Interface Format for Dolby Digital AC 3 audio T Button for ejecting the CA module 18 Mains power cable 19 On Off switch CA modules and smartcards are not included with this product The unit is not fully disconnected from the mains see the sections Safety Instructions Important Instructions and Periods of extended absence thunderstorms mains socket accessibility HDMI High Definition Multimedia Interface digital interface for video and audio Connection and setup Inserting batteries into the remote control Remove the cover on the rear of the remote control Insert the two batteries supplied into the remote control Ensure correct polarity of the batteries the and markings as indicated inside the battery compartment
6. Connect the SPDIF output electrical or optical to the Dolby Digital system using an appropriate cable Analogue If you want to play the sound on your hi fi system connect the audio cinch sockets to the input sockets on the hi fi system using an appropriate cable see Advanced connection example in the technical appendix Connecting up the Video DVD recorder Use a Scart cable to connect the satellite receiver VCR Scart socket to the video recorder PVR To play back a DVD i e output the signal from the PVR through the receiver on the TV set the TV set must also be connected to the receiver with a Scart cable This is necessary because the video signal from the VCR Scart socket of the receiver is not looped through forwarded to the HDMI output of the receiver If you are recording via an external video recorder DVD remember not to operate the receiver during recording otherwise all the on screen displays will appear on your recording SPDIF Sony Philips Digital Interface Format digital output for Dolby Digital AC 3 audio First Installation Connection and setup Before you start to use the UFS 932 read the sections Safety Instructions Important Instructions Important Information and Connection and Set Up through to the item First Installation Do not connect the unit to the mains until all installation work has been properly carried out The guidance provided in the First Installation section as
7. Operating instructions part 1 UFS 932 Connection and Setup English Safety Instructions Important NOol6S aci oiii iru rer nr cds aoo ku us s sajaa su j m k 2 SCOPE DI SU RO IRR NEN 5 Conneccion and Setups seus i essei ax uiu ar sausu d Ta znUu PUE TIERE ass E COE dEe UR ii 6 Front rear view of the receiver front flap open ccccccsseecccceseeeccesscecceusececcueeecsseucessseeeeessseeeessaseees 6 Inserting batteries into the remote CODIEFOL usus ocean rarae d re ihtati t 20S GERE ta ERR Ra ieg jies 8 CGonnecung the IY OU RR T TE 9 IE ere a a clei 2 twm P 9 AUCGIOCONMECI0NS ss S S S S S N S S 10 BITES ss cece EAT NN E NA aces eesru es A 10 PMV AMA streets te ttc rca tt teat U Rm 10 Connecting up the Video DVD recorder sees nennen nnne nnn nnn nans nna nnns 10 ERI TA AO PRIN RERUM N S SS S 11 Common Interface CI E 20 Inserting the HD card in The smart Card reader saie anas 20 Inserting the smart card and the CA module user nerit renti n RR RUE Rdn Reb ne iR Rab aenea bM bu Eure ERE S beds 21 ITGUBIESROCGUNG eet EE LT 22 BEIVICB is ca iem is esu sos ee ee eee 23 Technical append sarene mA n B8 24 Advanced connection examPlE iiii ras 24 Technical P CNEAI D5 ms T 25 Sat IF connection exarmipl6S uses reat inr b das Ent eae son
8. ange the batteries only with types that are identical or equivalent Otherwise the batteries and also the remote control may be damaged Comply also with the safety instructions stated on the batteries There is a risk of explosions Ventilation The heat generated in this unit is adequately dissipated However the unit should never be installed in a cupboard or on shelves with inadequate ventilation Never cover the cooling slots on the unit e g with other equipment magazines tablecloths clothing or curtains Do not place any objects on top of the unit Unless stated to the contrary in the Connection and Setup and Installation sections in the manual included maintain a clearance of at least 10 cm above the unit 2 cm to either side and 5 cm behind the unit to allow unobstructed dissipation of the heat generated There is a risk of fire Safety Instructions Important Notes Important Repairs Ensure that any repairs to your unit are carried out by qualified personnel Opening the unit and attempting to repair it yourself will invalidate the warranty Improper work on the unit may jeopardise the electrical safety of the unit The manufacturer accepts no liability for accidents caused by the user opening the casing of the unit Connections Incorrect wiring of the connections can lead to malfunctions or defects on the unit Periods of extended absence thunderstorms mains socket
9. arries a risk of death due to electric shock Playing children Make sure that children do not push any objects into the ventilation slots Risk of fatal injury due to electric shock Earthing The antenna system must be earthed as specified or equipotentially bonded EN 60728 11 and any national regulations must be complied with Risk of voltage surges due to lightning strikes Power supply voltage Operate the unit only at the specified mains voltage indicated on the rear of the unit or on the external power supply unit The unit may only be connected to the mains and turned on once it has been connected to the an tenna and to the TV set or the cable network and PC If the mains voltage is too high there is a risk of fire Warning Warning Do not cover Moisture direct sunlight heat naked flames Protect the unit against moisture dripping and splashed water do not place any filled objects such as vases on top of the unit Do not place the unit close to a heater or expose it to direct sunlight and do not operate it in damp locations Only use the unit in a moderate climate not in tropical conditions Place no naked flames such as candles on top of the unit There is a risk of fire Batteries If your unit was supplied with batteries e g for the remote control take care that the batteries are not exposed to excessively high temperatures direct sunshine or fire Exch
10. atellites that are present in the signal at the tuner You can set up a maximum of two satellites First use the lt buttons in the Satellite line to select the desired satellite then in the Port line assign it the position 1 If you wish your system to receive signals from a second satellite switch back to the Satellite and select the second satellite Then in the Port line assign this satellite the position 2 in the sequence When setting of the assigned User Band transmission channel and the User Band Frequency transmission frequency please refer to the documentation supplied with your system You will find there a printed list showing the assignment between the various transmission channels and the respective transmission frequencies Please note also that multiple receivers cannot share the same frequencies channels the receivers would interfere with each other User Band transmission channel Select a free available transmission E MGR 4 poo channel 1 8 AUS D SCR O 1284 MH Z User Band Frequency frequency of the SCR 1 1400 MHz ATTENUATION transmission channel SCR 2 1516 MHz 12 SCR 3 1632 MHz Select here one of the free available trans SCR 4 1748 MHz g 0 sd SCR 5 1864 MHz mission frequencies or use the numeric SCR 6 1980 MHz 4 pad to input the required frequency SCR 7 2096 MHz J See example on the right EXR 1581 for ass
11. ce If new software is released for your receiver and this affects the information in the operating manual e g changes to the menus and or functions if we believe it necessary we will make available a new operating manual for download under www kathrein de Make a note of the receiver s basic settings these are set during the first installation so you can restore them if necessary Please be aware of your responsibility towards your fellow man Keep the manual for any questions that arise later and if the building passes to another owner pass it on to the new owner Scope of supply m UFS 932 m 2 batteries AAA 1 5 V m HD smartcard m Operating instructions part 1 and part 2 m Remote control RC 674 m Safety instructions multi lingual m HDMI cable m HD flyer The accessories supplied may differ in appearance from those illustrated HDMI cable Remote Control onoff Zn ace iu Smartcard by ASTRA Batteries KATHREIN 6L AL e Mui ONE uo y HOA AL I H bys er AN 2 Sk V ko ne C MIJUHIEI iosopqpqpqpopapqr qr eae ee arr or qr op ar t D olus gd oz ilico dP ar or ar eae apap ar arora papa arar arar Nh 0 amp amp indi a 102100 a OZ asn 330 uou 7 e o amp Oi NI pci on NN AH1OG K O9plA ta 8l 9I St vl chk OL 8 Connection and setup Front rear view of
12. ignal at the tuner You can set up a maximum of four satellites First use the IES buttons in the Satellite line to select the desired satellite then in the Port line assign it the position 1 in the sequence of your satellites If you wish your system to receive signals from more than one satellite switch back to the Satellite and select a second satellite Then in the Port line assign this satellite the position 2 in the sequence Repeat this procedure until you have set up all the satellites whose signals you wish to receive Test transponder TP Select the selection field TP Here you can select a transponder for checking whether your settings are correct using the signal strength bar and signal quality bar When you have completed all settings press the n green button You will automatically be shown the display for Update LCN List Continue the first installation with the Update LCN List selection LCN Logical Channel Numbering Channels are sorted according to a list held in the receiver Connection and setup Single Cable System If you use a UAS 481 single cable LNB in your reception system you are only allowed to select one satellite 10600 MHz Puri c VA User Band Frequency 1284 MHz TP 69 12421 H 27500 Pres m in canas ho than red ons Select satellite and port satellite slot Here you can select the satellites whose signals you wish to receive Select only those s
13. ignment of a transmission channel to a transmission frequency Connection and setup Test transponder TP Select the selection field TP Here you can select a transponder for checking whether your settings are correct using the signal strength bar and signal quality bar When you have completed all settings press the n green button You will automatically be shown the display for Update LCN List Continue the first installation with the Update LCN List selection Update LCN list Update LCN List LEN List TV Programmes Radio Programmes Time amp Date of Last Check Time amp Date of Last Updais Select here whether you wish to use the channel list presorted in the factory Update LCN List or a channel list presorted for a specific country Change LCN List Update LCN List Press the button to load a channel list presorted in the factory Change LCN List Press the button to view the available channel lists presorted for the respective country Select the desired channel list and confirm your selection by pressing the button During the loading procedure for the channel list the following display may appear No new services found Confirm with the M button Cj exr As soon as the receiver has finished loading the channel list you can press the n green button to close the first installation LCN Logical Channel Numbering Channels are sorted according to a list held in the receiver Com
14. is type of system is preset Confirm the rest of the on screen displays during the first installation using the n green button You cannot damage your reception system during this process If you do not receive a TV picture at the end of the first installation contact your specialist dealer You should perform the antenna configuration make changes yourself only if you are fully familiar with the particulars of your reception system The individual items are selected using the 4 v buttons If you need to access sub menus they can be called up using the button The changes to the current settings can be performed using the lt gt buttons or the number pad You can set up the antenna tuner configuration for the following types of reception systems LNB only DiSEgC Y1 0 Unicable Continue as described in the initial installation for the type of reception you have selected Connection and setup LNB only Antenna Configuration Satellite High Oscillation Frequency 10600 MHz Select Satellite Use the IES buttons here to select the satellite whose signal is present at the tuner LNB Type If your reception system does not have a Universal LNB use the lt buttons to select the LNB types that are used in your reception system You can choose from the following LNB types Universal 1 Broadband Refer to the documentation for s seror your LNB or seek assistance from a specialist engineer
15. l appendix Single cable systems ERA 14 Single ESU 33 e 9 G EE Single ESU 33 GC HEELS ERA 14 ont Twin Single d SatAn ESU 33 93 O ESU 33 Q Sra UAS 584 585 z i E win ingle To me ESU 336 F F O ESU 33 9 GE Sat IF 950 2150 MHz Single ESU 33 Twin Single Single CIEMS Cua On CIETE 4 ESU 33 CQ ESU 34 Single Single Single CIEMI 3 ESU 33 GS ey ESU 33 gt GI ERA 14 ERA 14 Overvoltage protection KAZ 11 KAZ 12 Technical appendix Sat IF 950 2150 MHz Single Twin REESE 6 ESU 33 eo Single Twin Gre ESU 33 3 C EEE C GS ey ESU 33 ERA 14 ESD JESC Singl F 49 ESU 33 poate 7 Single Sat IF 950 2150 MHz Single ESU 33 63 ESU 33 9 ERA 14 Overvoltage protection KAZ 11 KAZ 12 For your notes For your notes l 936 4068 ZWT 0311 d Subject to changes nternet www kathrein de KATHREIN Werke KG Anton Kathrein Str 1 3 P O Box 100 444 83004 Rosenheim GERMANY phone 49 8031 184 0 Fax 49 8031 184 385
16. mon Interface Cl Connection and setup Always follow the operating instructions from your Pay TV provider and the N instructions supplied with the Smartcard and the CA Conditional Access module Smart cards and CA modules are not included with this product The cards and modules are issued by the respective pay TV providers and contain the subscriber data and details of the channels for which the subscriber has paid These channels are always scrambled Contact the Pay TV provider if you are interested in subscribing to a particular Pay TV channel You are responsible for the use of the smart card in the CA The smart card sold by the Pay TV provider specific to a particular encryption technology is inserted into the CA module Store your card and PIN code securely when not in use Inserting the HD card in the smart card reader The smart card reader small slot 2 on the UFS 932 Nagravision embedded is intended to be used for the HD card The smart card reader is behind the flap on right on the front underneath the Common Interface large slot It must be possible to insert the smart card chip contacts pointing down in the smart card reader without the need for a large amount of force Do not use excessive force and pay attention to the manual supplied with the smart card Inserting the CA module into the CI The Common Interface CI 3 of the UFS 932 is suitable for insertion of a Cl module o
17. o Pea Contes bs dase jum es DERE EIER RO Pbn TRU RIPE r tes ga 26 IE IVIGNSTIEC EPISNS SIC va san OT OO 26 Community antenna network systems 4 x Sat IF iid aaa nnn nnns nnne nnn n rns nna nnn nnns 26 Community antenna network systems 8 x Sat IF multi feed eeessssseseseeeeeeneenennnn menn 27 Community antenna network systems 16 x Sat IF MUIti fEOC ccc cc cece aaa 27 omgie AY S lli ssasss a S jj N OET ENE 28 If you do not know the configuration of your satellite reception system contact your specialist dealer for the first installation of your receiver KATHREIN Antennen Electronic Safety Instructions Important Notes These two pages contain important information about operation installation location and connection of the unit Head these instructions carefully before setting up the unit Danger Warning Mains cable Make sure that the mains cable power supply cable is not damaged Units with a damaged mains cable must be disconnected from the mains unplugged at the mains power socket and repaired by an electrical specialist before being used Only use the power supply unit supplied if available Risk of fatal injury due to electric shock Cleaning Disconnect the mains plug before cleaning the unit Only use a dry cloth for cleaning and only clean the outer surface Never open the casing of the unit Touching the parts inside the unit c
18. ocal Time Setting La 4 Here you can use the Ar buttons to select the correct local time setting e g Berlin for Germany Press the n green button to move to the next menu 4 Use the buttons here to select the basic AN Setting settings for the video output from the receiver to the TV set TV Aspect Ratio i For this refer to the operating manual for your TV set and take care to select only those settings that your TV set can process Resolution HDMI YUV format Here you can select the video resolution that will be output at the TV set Either 1080p resolution 1920 x 1080 full screen images 1080i resolution 1920 x 1080 half screen images No recording can be per formed at video resolution 720p resolution 1280 x 720 full screen images 1080p 676p resolution 720 x 576 full screen images This resolution can only be used for viewing the live signal 576i resolution 720 x 576 half screen images 480p resolution 640 x 480 full screen images 480i resolution 640 x 480 half screen images TV Mode This setting depends on the resolution previously selected and is performed automatically by the receiver Connection and setup TV Aspect Ratio Here you can select the TV picture format Either 4 3 16 9 or Auto Scaling Method Here you can select the screen display mode TV Scale The format transmitted by the programme pr
19. output digital 1 x HDMI Audio output analogue 2 x Cinch sockets Audio output digital Standard fibre optic cable SPDIF Data interface Common Interface encryption system For 1 Cl or Cl module Nagravision USB 1 x 2 0 General information Ambient temperature C Max 5 to 40 Unit dimensions W x H x D weight mm kg 210 x 40 x 310 2 2 5 Technical appendix Sat IF connection examples Individual reception systems Position OPTIO UC1 Y E 3 ESD ESC Sat IF 950 215U MHZ f X UAS 584 s ESD ESC Sat IF 950 2150 MHz 3 ESD ESC Overvoltage protection KAZ 11 KAZ 12 Community antenna network systems 8 x Sat IF multi feed Technical appendix ESD ESC N N LLL IM POPPE SS Sat IF 950 2150 MHz ESD ESC Community antenna network systems 16 x Sat IF multi feed IEEE UAS 584 ESD ESC di WH T Ol oq saimn 1 z 1 x UAS 584 m 702 TI Sat IF d 950 2150 MHz gel Y t di ar e x La T UAS 584 e Hl ESD JESC ESD ESC 9 ESD ESC n nn t Dn im il hannah 2x UAS 584 ume Sat IF oe 950 2150 MHz i E 1 r n 4 ESD ESC 49 ESD ESC Overvoltage protection KAZ 11 KAZ 12 27 B BIZ E E li E Sat IF 950 2150 MHz Technica
20. ovider is used Letterbox The picture is reduced to suit the TV screen there may be black bands above and below it Pan amp Scan Zoomed in Zoom Stretched full screen HDCP Enabled Here you can select whether HDCP digital copy protection is set to On at all times or is Off not activated To view some programmes it may be necessary for the setting to be set to On Video Output Here you can select whether the receiver will output the RGB signal at the Scart sockets selection RGB Red Green Blue signal If the setting RGB is selected no TV signal can be output at the YPbPr sockets Important instruction for picture output using the YPbPr sockets If you TV set is connected to the receiver using the YPbPr sockets it is essential that the video output setting YPbPr is selected Press the n green button to move to the next menu Connection and setup The following on screen display appears Antenna Configuration The settings for the tuner configuration should be perfo 69 12421 I 27500 rmed by a specialist engineer for this reception system If your receiver is connected as in the connection example see Connecting the receiver in this section no changes are necessary for the remainder of the first installation If you are not familiar with the details of your reception system note the following In many cases the satellite reception system is a DiSEgC V1 0 system Th
21. ow spent batteries into your domestic waste take them to a collection point for spent batteries The HD card is intended for use exclusively within the German Federal Republic by ASTRA 3 Safety Instructions Important Notes Product return original packaging Please keep the original packaging in case you need to return the product at any time The receivers are fragile due to their construction and are only adequately protected by the original packaging If the receiver is not shipped correctly the guarantee warranty on it will be voided Ventilation slots on the unit Make sure that the ventilation slots on the unit are not blocked or covered in any way Otherwise the unit may overheat There is a risk of fire Warning Switching the receiver off Before you switch disconnect the receiver from the mains you must switch it to the standby mode by pressing the stand by button on off on the remote control In standby mode any changed or new data that are broadcast will be saved by the receiver As soon as the receiver is in the standby mode it can be disconnected from the mains at any time You must not disconnect the receiver from the mains while it is in operation This can lead to a loss of data and corruption of the software Miscellaneous The information in this operating manual was correct at the time of going to print We reserve the right however to make changes at any time and without prior noti
22. r CA module and is located on the front panel of the receiver behind the flap The CA module 2 accepts the smart card 1 chip contacts pointing downwards and towards socket strip and is then inserted in the Cl slot 3 The smart card should be inserted into the CI or CA module without exerting excessive force The same applies to inserting the CI or CA module into the Cl slot Do not use without excessive force and follow the instructions supplied with the Smartcard and the Cl or CA module To remove the CI or CA module press the ejection button 4 and pull it out straight backwards Troubleshooting In the event of a malfunction first check all the cable connections and operating states 1 Receiver and TV set power plugs are connected to wall socket gt Oo BR O ND Antenna cables are connected to the receiver input Receiver is responding to remote control selection of troubleshooting tips is offered below Receiver and TV set correctly connected by a HDMI or Scart cable Audio connections are made to the Hi Fi or Dolby Digital system as appropriate Receiver and TV set Hi Fi Dolby Digital system are switched on check power indicators Problem Cause Remedy A No signal warning appears on some or all channels Consult an antenna specialist to have it checked and repaired as necessary Check the settings performed in the Settings Antenna amp Satellite Remote control
23. sumes that the receiver has been properly connected as per the Safety Instructions Important Information and Connection and Set Up chapters through to the First Installation section Required buttons on remote control for first installation i i B Proceed to the next step in Ce S a green the first installation B Go back one step in the Confirm the changed values setting call up the submenus red first installation 4 Select change individual i menu parameters navigation Cancel entry go back First switch your TV set on and select the AV HDMI input you have used to connect the receiver to your TV set Switch on the receiver at the power switch on the rear of the unit Undertake the first installation If you have any questions or encounter problems contact your specialist dealer The following on screen display appears Language Settings German EL French Z Spanish B Turkish Always pay attention to the bar at the Lo bottom of the on screen display This he Czech provides information on what to do next M ll Use the 4 v buttons to select the desired menu language for your UFS 932 and confirm your selection using the button Connection and setup The following languages are available German English French Italian Spanish Czech Dutch Polish Turkish and Russian Press the n green button to move to the next menu The following on screen display appears L
24. ternal hard disk QI DOLBY DIGITAL po icht Offnenl dh E di di 220 240V 50 60Hz 25W tr lanutac ured ul Ol ol aborartol jouble U syml 0 0 abor IF 9 INPUT 50 2150MHz 13 18V 5 300mA max 22kHz Y Pb nder license from ee fei d Cinch YPbPr Dolby Digital Dolby Digital system Technical appendix Technical Specifications Type UFS 932si HD UFS 932sw HD Order no colour 20210188 silver 20210189 black RF section Sat IF band MHz 950 2150 Input level band dBHV 44 83 TV system video Modulation FEC demultiplexer DVB S DVB S2 standard ideo kien CCIR 601 720 x 976 lines 576i 576p 720p 1080i 1080p Video decryption MPEG 2 MPEG 4 compatible Input data rate MSymb s 2 45 30 for DVB S2 8PSK S N dB 253 TV system audio Decryption AC 3 MPEG 1 layers 1 and 2 Sampling rate kHz 32 44 1 48 S N dB 265 Power Supply Power supply voltage V Hz 230 10 50 60 Power consumption max typ operation standby W lt 25 12 1 LNB supply horiz vert V mA 14 18 max 350 Control signal kHz 22 DISEqCTM1 0 SCR single cable system Connections Sat IF input output 2 x F socket TV VCR connection 2 x Scart sockets Video output analogue 3 x Cinch socket YPbPr 1 x Cinch socket Video audio
Download Pdf Manuals
Related Search