Home

PC CHIPS P63G (V1.0) motherboard

1. This item shows the current processor speed Processor Stepping 206a3 This item shows the processor stepping version Microcode Revision 8 This item shows the Microcode version Processor Cores 4 This item shows the core number of the processor Intel HT Technology Supported This item shows that your computer supports Intel HT technology or not Hyper threading Enabled This item is only available when the chipset supports Hyper threading and you are using a Hyper threading CPU Limit CPUID Maximum Disabled Use this item to enable or disable the maximum CPUID value limit When supports Prescott and LGA775 CPUs enables this to prevent the system from rebooting when trying to install Windows NT 4 0 Excute Disable Bit Enabled This item allows the processor to classify areas in memory by where application code can execute and where it cannot When a malicious worm attempts to insert code in the buffer the processor disables code execution preventing damage or worm propa gation Replacing older computers with Execute Disable Bit enabled systems can halt worm attacks reducing the need for virus related repair Intel Virtualization Technology Disabled When disabled a VMM cannot utilize the additional hardware capabilities provided by Vandor Pool Technology Power Technology Energy Efficient Use this item to control the Energy mode of the processor Press lt Esc gt to return to the Advanced
2. This is for Turbo mode Power Limit 2 Switch Enabled Use this item to control the Power Limit 2 This is for Turbo mode Motherboard User s Guide Power Limit 2 Value 81 Use this item to control Power Limit 2 PL2 provides an upper limit of the TDP excursions This is for Turbo mode Long Duration maintainded 1 Use this item to control the time window over PL1 value should be maintained This is for Turbo mode Enhanced Intel SpeedStep Technology Enabled This item allows users to enable or disable the EIST Enhanced Intel SpeedStep Technology Turbo Mode Enabled This item allows you to control the Intel Turbo Boost Technology 1 2 3 4 Core Ratio 31 31 0 0 This item shows the Core Ratio limit value Press lt Esc gt to return to the Performance Tunning page gt Chipset Configuration Scroll to this item to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc VET MACK Et Sunq Tweak KOT ENARA Disabled Enabled GT Memory Multiplier Configuration OverClocking Memory Multiplier 10 67 Memory Timing Configuration CAS Latency tCL 8 Row Precharge Time tRP 8 RAS to CAS Delay tRCD 8 RAS Active Time tRAS 20 Intel Graphics Configuration GT OverColocking Enabled Graphics Current Normal Graphics Core Ratio Limit 22 Version 2 02 1205 Copyright C 2010 American Megatrends Inc Memory Multiplier Configuration This item s
3. amp Applications The Browse CD button is a standard Windows command that you can check the contents of the disc with the Windows file browsing interface The Exit button closes the Auto Setup window To run the program again reinsert the DVD ROM CD ROM disc in the drive or click the DVD ROM CD ROM driver from the Windows Explorer and click the Setup icon The Utilities button brings up a software menu It shows the bundled software that this mainboard supports The Information brings you to the Install Path where you can find out path names of software driver Auto Installing under Windows XP Vista 7 If you are under Windows XP Vista 7 please click the Setup button to run the software auto installing program while the Auto Setup screen pops out after insert ing the support DVD ROM CD ROM 1 The installation program loads and displays the following screen Click the Next button Welcome x Welcome to the MainBoard Setup program This program will install MainBoard on your computer itis strongly recommended that you exit all Windows programs before running this Setup program Click Cancel to quit Setup and then close any programs you have running Click Next to continue with the Setup program WARNING This program is protected by copyright law end international treabes Unauthorized reproduction or distribution of this program or any portion of i may result in severe civil and criminal penalties and will be
4. Audio e 5 1 2 Channel High Definition Audio Codec e Meets Microsoft WLP3 x Windows Logo Program audio requirements All DACs supports 44 1k 48k 96k 192kHz sample rate e Software selectable 2 5V 3 2V 4 0V VREFOUT e Direct Sound 3D compatible e Power Support Digital 3 3V Analog 5 0V Note Due to the DRAM maximum size is 4 GB at present the memory maximum size we have tested is 8 GB Chapter 1 Introduction Onboard LAN Optional Supports PCI Express TM 1 1 Integrated 10 100 1000 transceiver Wake on LAN and remote wake up support Supports PCI Express TM 1 1 Integrated 10 100 transceiver Wake on LAN and remote wake up support Onboard I O Ports e Two PS 2 ports for mouse and keyboard e One VGA port e One LAN port e One HDMI port e Four USB 2 0 ports e Audio jacks for microphone line in and 6 ch line out BIOS Firmware The motherboard uses AMI BIOS that enables users to configure many system features including the following e Power management e Wake up alarms e CPU parameters e CPU and memory timing e Graphic parameters The firmware can also be used to set parameters for different processor clock speeds Dimensions e Micro ATX form factor of 225x180 mm Note Hardware specifications and software items are subject to change without notification Motherboard User s Guide Package Contents Your motherboard package ships with the following items 0 The motherboard Q Two Serial ATA cables 0
5. Control Panel PAll Control Panel Items P Display p Screen Resolution Search Control Panel Change the apprearance of your displays om E Display 4 AL1717 Resolution 1920 x 1200 recommended Orientation Landscape Multiple displays Disconnect this display v ZX You must select Apply before making additional changes Make this my main display Advance settings Make text and other items larger or smaller What display settings should choose OK Cancel Apply o xX Search Control Panel Change the apprearance of your displays om E Display 4 AL1717 Resolution 1920 x 1200 recommended Orientation Landscape Y Multiple displays Extend desktop to this display w AX You must select Apply before making additional changes Make this my main display Advance settings Make text and other items larger or smaller What display settings should choose OK Cancel Apply 36 Chapter 3 BIOS Setup Utility gt South Bridge Scroll to this item and press lt Enter gt to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc ETC I Chipset ELTU fellas leis mest Woke South Bridge Specify what state to go to when power is re applied after a power failure G3 state Audio Configuration Azalia HD Audio Enabled Select Screen Azalia Internal HDMI codec Enabled I Select Item Enter Select C
6. ST SE EZ YOU SSS USB Configuration Enabled Disabled All USB Devices B Legacy USB Support rete Sa Select Screen tT Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc All USB Devices Enabled Use this item to enable or disable all USB devices Legacy USB Support Enabled Use this item to enable or disable support for legacy USB devices Setting toAudio allows the system to detect the presence of the USB device at startup If detected the USB controller legacy mode is enabled If no USB device is detected the legacy USB support is disabled Press lt Esc gt to return to the Advanced Setup page 29 Motherboard User s Guide Super IO Configuration Scroll to this item and press lt Enter gt to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main Advanced Chipset Tweak Boot Security Save amp Exit Super IO Configuration Set Parameters of Serial a Port 0 COMA Select Screen tl Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2012 American Megatrends Inc gt Serial Port 0 Configuration This item shows the information of
7. The Software support disk Optional Accessories You can purchase the following optional accessories for this motherboard 0 The Extended USB module 0 The Serial ATA power cable Note You can purchase your own optional accessories from the third party but please contact your local vendor on any issues of the specification and compatibility Chapter 2 Motherboard Installation To install this motherboard in a system please follow these instructions in this chapter Q n Identify the motherboard components Install a CPU Install one or more system memory modules Make sure all jumpers and switches are set correctly Install this motherboard in a system chassis case Connect any extension brackets or cables to headers connectors on the motherboard Install peripheral devices and make the appropriate connections to headers connectors on the motherboard D Note 1 Before installing this motherboard make sure jumper CLR_CMOS is under Normal setting See this chapter for information about locating CLR_CMOS and the setting options 2 Never connect power to the system during installation otherwise it may damage the motherboard Motherboard User s Guide LABEL COMPONENTS 1 CPU Socket LGA1155 socket for 2 Generation Intel Core Family Processors 2 CPU_FAN 4 pin CPU cooling fan connector 3 DDR3_1 2 240
8. Windows 7 1 Enter the Control Panel menu select the Display in the All Control Panel Items and click the Screen Resolution then appears the following screen Show the path of the setting location Display devices x Caps gt Control Panel gt All Control Panel Items Display Screen Resolution lm Change the apprearance of your displays Detect Identify Display Resolution 1920x 1200 recommended y Orientation Landscape Multiple displays C Extend desktop to this display This is currently your main display Advance settings Make text and other items larger or smaller What display settings should choose Cancel Apply The type of the display Set the multiple displays 2 Select display devices set the multiple displays option and to extend destop for display Multi Monitor technology OX y Control Panel All Control Panel Items Display Screen Resolution Search Control Panel Change the apprearance of your displays E lt Display 3 DELL U2410 v Resolution 1920x 1200 recommended Orientation Landscape Multiple displays Disconnect this display Extend desktop to this display A You must select Disconnect this display anges Make this my main qispiay Advance settings Make text and other items larger or smaller What display settings should choose OK Cancel Apply 35 Motherboard User s Guide f x
9. gt Performance Tunning Scroll to this item to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc UEM Cu M Ea Tweak F I E M23411 Performance Tuning CPU Configuration p Chipset Configuration Select Screen t Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc gt CPU Configuration Scroll to this item to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc EI Kel Tq Tweak MEOS E mab did IA Core Current CPU Ratio 31 Power Limit 1 Value Watt 65 Power Limit 2 Switch Enabled Power Limit 2 Value 81 Select Screen Long duration Maintained 1 11 Select Item Enhanced Intel SpeedStep Technology Enabled Enter Select Turbo Mode Enabled Change Opt 1 Core Ratio Limit 31 F1 General Help 2 Core Ratio Limit 31 F2 Previous Values 3 Core Ratio Limit 0 F3 Optimized Defaults 4 Core Ratio Limit 0 F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc CPU Ratio 31 This item allows users to control non turbo CPU ratio IA Core Current Normal Use this item to control CPU Current Limit This is for Turbo mode Power Limit 1 Value Watt 65 Use this item to control the limit of the TDP
10. isesccesccsssicsensiscvssstitsissenasia ssastestesdecissavestsdeedisesstesassaseawerssusedesuesteedssdssensaseececesesseey Installing the PHrOCESSOP orrua AEE EL EEN Aa Installing Memory Mod lesoosa ay amu aan akanan uqa ARTEA Jumper SCUINGS iscscrcsccrevscicisssssveccrssssdecsavsdercsaveateaeedisassdasassaseovessdisusssucvaveasscssensaseuctcccests Install the Motherboard sccccssssssscesissscesvssessssscesesteisedeseeTasvsedesansnssuatessassssesveteaevasecseceete Connecting Optional Devices Install Other Depite ay qaasawaaasawaqn qasqa aTi EAE EI E qa ws Expansion Slots seisseen iienoaiti ad NEER NEERA Chapter 3 BIOS Setup Utility ssssssssssssssscssosrossossssvssssossossss ssisorosvosrsssssssssssoss 20 Introduction au sau ua uA wa u apyu a a qaywa O EAA 20 Running the Setup UND saus nasha u tarar AATE EAG 20 Main Setup PAQE sscisicscssscncseccssvessdissasszesact cesscestasbisesscusvabecdecssesesedesaovssssdseasessedpelsueivanets 21 Advanced Setup Page asa alana aia a EAR aides sastesscieuss 24 Chipset Setup Page a s nn aS S au a EA ane Wa m Suay ee asses 32 Tweak Setup Page 139 Boot Setup Page 45 Securtiy Setup Page 46 Save amp Exit Set p PAGE scccscvcssiasiccsasssissersivesestsccesivssscseasdassendssepecdasestscassiascesesstetessenssie 47 Chapter 4 Software amp Applications 48 JTnirodhieloti p n a es PEA A aq LE MEE 48 Installing Support SoftW
11. pin DDR3 SDRAM slots 4 ATX_POWER Standard 24 pin ATX power connector 5 SPILDEBUG SPI debug header for factory use only 6 SATA1 4 Serial ATA 3 0 Gb s connectors 7 F PANEL Front panel switch LED header 8 F_LUSB1 2 Front panel USB header 9 CASE CASE open header 0 ME_UNLOCK ME unlock header for factory use only 1 TPM Trusted Platform Module header 2 SPK Speaker header 3 CLR_CMOS Clear CMOS jumper 4 COM Onboard serial port header 5 SPDIFO SPDIF out header 6 SYS_FAN 3 pin system cooling fan connector 7 F_AUDIO Front panel audio header 8 PCIE1 2 PCI Express x1 slots 9 PCIEX16 PCI Express slot for graphics interface 20 ATX12V 4 pin 12V power connector 6 I O Ports The illustration below shows a side view of the built in I O ports on the motherboard PS2 USB 2 0 Mouse ports LAN port Line in lt e Line out oil Microphone PS2 HDMI port VGA port USB 2 0 ports keyboard S ene pe FS pao arena PST THIEN c LAN Port Connect an RJ 45 jack to the LAN port to connect your computer to the Netw ork USB 2 0 Ports Use the USB 2 0 ports to connect USB 2 0 devices Audio Ports Use the three audio jacks to connect audio devices The first jack is for stereo Line In signal the second jack is for stereo Line Out signal and the third jack for Microphone Motherboard User s Guide Installing the Processor This motherboard has a LGA1155 socket for latest 2 4 Generation Intel Core Fami
12. the Browse CD item then appears the following screen Select the driver you want to install e g NVIDIA GeForce 8400 GS Microsoft Corporation WDDM v1 1 and double click it File Action View Help TEH on SS a g ECS PC gt qi Computer gt Gs Disk drives a Display adapters E NVIDIA GeForce 8400 GS Microsoft Corporation WDDM v1 1 b AQ DVD CD ROM drives p Human Interface Devices gt Gq IDE ATA ATAPI controllers b gt Keyboards p B Mice and other pointing devices b Monitors b i Network adapters b Portable Devices B Processors D a Sound video and game controllers b gill System devices gt Universal Serial Bus controllers Step 3 Enable IGD Multi Monitor from BIOS In the following BIOS screen please set IGD Multi Monitor to Enabled Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main Advanced Chipset Tweak Boot Security Save amp Exit North Bridge Enabled Disabled IGD Multi Monitor by Internal Initate Graphic Adapter PCI Express Graphics Decive IGD Memory 64M DVMT Mode Select DVMT Mode DVMT FIXED Memory 256MB Select Screen 1 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc 34 Chapter 3 BIOS Setup Utility Step 4 Change the appearance of your displays under
13. 1 Make sure the monitor is turned on and the monitor cable is properly connected to the PC 2 Check the VGA adapter card if applicable is inserted properly 3 Listen for beep sounds If you are using internal PC speaker make sure it is connected a continuous 3 short beeps memory not detected b 1 long beep and 8 short beeps VGA not detected 51 c The PC suddenly shuts down while booting up 1 The CPU may experience overheating so it will shutdown to protect itself Ensure the CPU fan is working properly 2 From the BIOS setting try to disable the Smartfan function to let the fan run at default speed Doing a Load Optimised Default will also disable the Smartfan Start up problems after prolong use After a prolong period of use your PC may experience start up problems again This may be caused by breakdown of devices connected to the motherboard such as HDD CPU fan etc The following tips may help to revive the PC or identify the cause of failure 1 Clear the CMOS values using the CLR_CMOS jumper Refer to CLR_CMOS jumper in Chapter 2 for Checking Jumper Settings in this user manual When completed follow up with a Load Optimised Default in the BIOS setup 2 Check the CPU cooler fan for dust Long term accumulation of dust will reduce its effectiveness to cool the processor Clean the cooler or replace a new one if necessary 3 Check that the 12V power amp ATX connectors are fully inserted into the motherboard con
14. 3 DUAL SMBDATA SERIRQ LAD3 LAD2 VCC3 LAD1 17 GND WN CASE Chassis Intrusion Detect Header This detects if the chassis cover has been removed This function needs a chassis equipped with instrusion detection switch and needs to be enabled in BIOS Short Chassis cover is removed Open Chassis cover is closed ME_UNLOCK ME Unlock Header Pin Short Fuction Unlock Open Lock 16 Chapter 2 Motherboard Installation Install Other Devices Install and connect any other devices in the system following the steps below SATA4 S SATA3 SATA2 SATA1 Serial ATA Devices The Serial ATA Advanced Technology Attachment is the standard interface for the IDE hard drives which is designed to overcome the design limitations while enabling the storage interface to scale with the growing media rate demands of PC platforms It provides you a faster transfer rate of 3 0 Gb s If you have installed a Serial ATA hard drive you can connect the Serial ATA cables to the Serial ATA hard drive or the connector on the motherboard On the motherboard locate the Serial ATA connectors SATA1 4 which support new Serial ATA devices for the highest data transfer rates simpler disk drive cabling and easier PC assembly It eliminates limitations of the current Parallel ATA interface but maintains register compatibility and software compatibility with Parallel ATA 17 Motherboard User s Guide Expan
15. 5 Copyright C 2010 American Megatrends Inc TPM Support Enabled This item enables or disables TPM support Current TPM Status Information This item shows the information of current TPM status NO TPM Hardware This item shows the TPM status 31 Motherboard User s Guide Chipset Setup Page The chipset menu items allow you to change the settings for the North chipset South chipset and other system Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main Advanced Chipset Tweak Boot Security Save amp Exit North Bridge Parameters gt South Bridge gt ME Subsystem Select Screen l Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc gt North Bridge Scroll to this item and press lt Enter gt and view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main C Chipset Tweak Boot Security Save amp Exit North Bridge IGD Share Memory Size DVMT Mode Select DVMT Mode DVMT FIXED Memory 256MB IGD Multi Monitor Disabled Select Screen l Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit IGD Memory 64M This item shows the information of the IGD Intern
16. Follow the case manufacturer s instructions to use the hardware and internal mounting points on the chassis ATX_POWER SYS_FAN F_PANEL Connect the power connector from the power supply to the ATX_POWER connector on the motherboard The ATX12V is a 12V connector for CPU Vcore power If there is a cooling fan installed in the system chassis connect the cable from the cooling fan to the CPU_FAN fan power connector on the motherboard Connect the case switches and indicator LEDs to the F_PANEL header Here is a list of the F_LPANEL pin assignments Pin Signal Pin Signal J 1 HD LED P FP PWRYSLP HD_LED_N FP PWRISLP 5 RESET swng 6 POWER sw Pe 7 RESET SW PJ s FOWER SW ND Ds Rsv DN TO Key 13 Motherboard User s Guide Connecting Optional Devices Refer to the following for information on connecting the motherboard s optional devices SPI_DEBUG SPK Speaker Header Connect the cable from the PC speaker to the SPK header on the motherboard Pn Signal Pin Signal Key SPDIFO SPDIF Out Header S PDIF Sony Plilips Digital Interface is a standard audio transfer file format and allows the transfer of digatal audio signals from one device to another without having to be converted first to an analog format Via a specific audio cable you can connect the SPDIFO header S PDIF output on the motherboard to the S PDIF digital input on the external speake
17. Megatrends Inc ACPI Sleep State S3 Suspend to RAM This item allows user to enter the APCI S3 Suspend toRAM Sleep State default Press lt Esc gt to return to the Advanced Setup page CPU Configuration Scroll to this item and press lt Enter gt to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc WEHE Advanced WI am TZ US Geol gL NTA e dd Enabled foir Windows XP and P fi CRU Configuration Linux OS optimized for P Hyper Threading Technology Genuine Intel R CPU 0 3 00GHz ypa EMT and Disabled for other OS OS ae Speed seek ae not optimized for Processor Stepping 206a3 Hyper Threading Technology MicracodelRevicion 8 When Disabled only one thread Processor Cores 4 per enabled core is enabled Intel HT Technology Supported Select Screen Limit CPUID Maxi Disabled 1l cee hen mi aximum isable Enter Select Execute Disable Bit Enabled sansa O Intel Virtualization Technology Enabled F1 General Help Power Technology Energy Efficient F2 P EEIE VEES F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc Chapter 3 BIOS Setup Utility Genuine Inter R CPU 0 3 00GHz This is display only field and diaplays the information of the CPU installed in your computer EMT64 Supported This item shows the computer supports EMT64 Processor Speed 3000MHz
18. Motherboard User s Guide This publication including photographs illustrations and software is under the protection of international copyright laws with all rights reserved Neither this user s guide nor any of the material contained herein may be reproduced without the express written consent of the manufacturer The information in this document is subject to change without notice The manufac turer makes no representations or warranties with respect to the contents hereof and specifically disclaims any implied warranties of merchantability or fitness for any particular purpose Further the manufacturer reserves the right to revise this publication and to make changes from time to time in the content hereof without obligation of the manufacturer to notify any person of such revision or changes Trademarks IBM VGA and PS 2 are registered trademarks of International Business Ma chines MMX Pentium Pentium II Pentium III Celeron are registered trademarks of Intel Corporation Microsoft MS DOS and Windows XP Vista 7 are registered trademarks of Microsoft Corporation AMI is a trademark of American Megatrends Inc It has been acknowledged that other brands or product names in this manual are trademarks or the properties of their respective owners Static Electricity Precautions 1 Don t take this motherboard and components out of their original static proof package until you are ready to install them 2 While insta
19. Setup page 27 Motherboard User s Guide SATA Configuration Use this item to show the mode of serial SATA configuration options Aptio Setup Utility Copyright C 2010 American Megatrends Inc VET Advanced Reil a ISI Tai IE 34 SATA Configuration 1 IDE Mode 2 AHCI Mode Serial ATA Controller 0 Compatible Serial ATA Controller 1 Enhanced SATA Port1 Not Present SATA Port2 Not Present Select Screen SATA Port3 Not Present 1 Select Item SATA Port4 Not Present Eror Saee Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc SATA Mode IDE Mode Use this item to select SATA mode Serial ATA Controller 0 1 Compatible Enhanced Use this item to select the Serial ATA cotroller options Disabled Compatible En hanced SATA Port 1 4 Not Present This motherboard supports four SATA channel and each channel allows one SATA device to be installed Use these items to configure each device on the SATA channel Note H61 Chipset is not fully support AHCI Mode HW support only Press lt Esc gt to return to the Advanced Setup page 28 Chapter 3 BIOS Setup Utility USB Configuration Scroll to this item and press lt Enter gt to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc WEE Advanced SUPE S Z
20. This motherboard has a LGA1155 socket for latest 2 4 Generation Intel Core Family processors for high end business or personal desktop markets This motherboard is based on Intel H61 Express Chipset for best desktop plat form solution H61 is a single chip highly integrated high performance Hyper Threading peripheral controller unmatched by any other single chip device con troller This motherboard supports up to 16 GB of system memory with dual ch annel DDR3 1333 1066 SDRAM High resolution graphics via PCI Express x16 slot intended for Graphics Interface is fully compliant to the PCI Express Base Specification revision 2 0 In addition two PCI Express slots are supported It implements an EHCI Enhanced Host Controller Interface comp liant interface that provides eight USB 2 0 ports four USB 2 0 ports at the back panel and two USB 2 0 headers support additional four USB 2 0 ports The motherboard is equipped with advanced full set of I O ports in the rear pan el including PS 2 mouse and PS 2 keyboard connectors one HDMI port one D_sub VGA port one Lan port four USB 2 0 ports and audio jacks for micr ophone line in and 6 ch line out In addition this motherboard supports four SATA 3 0 Gb s connectors for expan sion Key Features The key features of this motherboard include LGA 1155 Socket Processor e Accommodates latest 2 4 Generation Intel Core Family processors e Supports Hyper Threading techno
21. a software command If you enable this item the system can automatically resume if there is an incoming call on the PCI Modem or PCI LAN card You must use an ATX power supply in order to use this feature Use this item to do wake up action if inserting the PCI card Resume By USB S3 Disabled This item allows you to enable disable the USB device wakeup function from S3 mode Resume By PS2 KB S3 Disabled This item enables or disables you to allow keyboard activity to awaken the system from power saving mode Resume By PS2 MS S3 Disabled This item enables or disables you to allow mouse activity to awaken the system from power saving mode EUP Support Enabled This item allows user to enable or disable EUP support Power Led Type Dual Color LED This item shows the type of the power LED Press lt Esc gt to return to the Advanced Setup page 25 Motherboard User s Guide ACPI Setting The item in the menu shows the highest ACPI sleep state when the system enters suspend Aptio Setup Utility Copyright C 2010 American Megatrends Inc WEE Advanced KAEA SE e SESI E AA ACPI Settings Selectthe highest ACPI sleep state the system will enter when the SUSPEND button is pressed Select Screen t Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American
22. al Graphics device memory DVMT Mode Select DVMT Mode This item allows you to select the DVMT operating mode DVMT FIXED Memory 256MB When set to Fixed Mode the graphics driver will reserve a fixed position of the system memory as graphics memory according to system and graphics requirements 32 Chapter 3 BIOS Setup Utility IGD Multi Monitor Enabled This item enables or disables IGD Internal Graphics device multi monitor Press lt Esc gt to return to the Chipset Setup page Multi Monitor technology Multi Monitor technology can help you to increase the area available for programs running on a single computer system through using multiple display devices It is not only to increase larger screen viewing but aslo to improving personal productivity Intel Integrated Graphics PCI Express Graphics Sow 3 Please note that Multi Monitor technology supports up to four monitors one or two Intel integrated Graphics and one or two PCI Express graphics devices under Windows 7 Step 1 Insert PCCHIPS drives DVD to run Auto setup or browse the DVD to install Intel chipset drivers VGA and sound drivers If you want know the detail information please refer to chapter 4 F per tg Mainboard Setup Utility Drivers Utilities T Information 33 Motherboard User s Guide Step 2 Install all the drivers of PCI Express graphic cards Click
23. are asa au s ua a una EA 48 Bundled Software Installation u u a h anna u qaa aa kiii 50 Chapter 5 Trouble Shooting sssssssssssssssssssssscsassssovssvessssvosvsssss sosssoscosvossosssssessss OL Start up problems during ASSCMDIY c cscescsssesscssseadesnsascodsdssovancsesassesaesesdensssdeae s 51 Startup problems Gfter Prolong USCsccissscssccsivessrciessacosadsseieaisivsedivdedes Estan Niar 52 Maintenance and care tips Basic Troubleshooting Flowchart ii Motherboard User s Guide Notice 1 Owing to Microsoft s certifying schedule is various to every supplier we might have some drivers not certified yet by Microsoft Therefore it might happen under Windows XP that a dialogue box shown as below pop out warning you this software has not passed Windows Logo testing to verify its compatibility with Windows XP Please rest assured that our RD department has already tested and verified these drivers Just click the Continue Anyway button and go ahead the installation Hardware Installation The software you are installing for this hardware HSP56 MicroModem has not passed Windows Logo testing to verify ts compatibility with Windows XP Tell me why this testing is important either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing iii Chapter 1 Introduction
24. ase Open Warning Disabled Change Opt Chassis Opened No F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc Restore AC Power Loss Power Off This item enables your computer to automatically restart or return to its operating status Audio Configuration This item shows the information of the audio configuration Azalia HD Audio Enabled This item enables or disables Azalia HD audio Azalia Internal HDMI codec Enabled This item enables or disables Azaia Internal HDMI codec Case Open Warning Disabled This item enables or disables the warning if the case is opened up and the item below indicates the current status of the case Chassis Opened No This item indicates whether the case has been opened Press lt Esc gt to return to the Chipset Setup page 37 Motherboard User s Guide gt ME Subsystem Scroll to this item and press lt Enter gt to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc ET Chipset iil ame f SIT a dl Intel ME Subsystem Configuration ME Subsystem Help ME Version 7 0 2 1164 Select Screen l Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 Amer
25. e Press lt Esc gt to return to the PC Health Status page System Component Characteristics These items display the monitoring of the overall inboard hardware health events such as System amp CPU temperature CPU amp DIMM voltage CPU amp system fan speed etc CPU Fan Speed CPU Voltage DIMM Voltage VAXG Voltage Press lt Esc gt to return to the Advanced Setup page 24 Chapter 3 BIOS Setup Utility Power Management Setup This page sets up some parameters for system power management operation Aptio Setup Utility Copyright C 2010 American Megatrends Inc WEE Advanced iqu IS Sa 018 ATR bd Power Management Setup About Resume by Ring Resume By PCI PCI E Lan PME Disabled Resume By USB S3 Disabled Resume By PS2 KB S3 Disabled gt Select Screen Resume By PS2 MS S3 Disabled Select Item EUP Function Enabled Enter Select Power Led Type Dual Color LED t Change Opt 1 General Help 2 Previous Values 3 Optimized Defaults 4 Save amp Exit SC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc Resume By RING Disabled The system can be turned off with a software command If you enable this item the system can automatically resume if there is an incoming call on the Modem You must use an ATX power supply in order to use this feature Resume By PCI PCI E Lan PME Disabled The system can be turned off with
26. etup page 43 Motherboard User s Guide B O M P Technology Enabled This item allows users to enable or disable B O M P technology This function can run safe setting to setup menu when system boot fail 3 times Auto Detect DIMM PCI Clk Enabled When this item is enabled BIOS will disable the clock signal of free DIMM PCI slots Spread Spectrum Enabled If you enable spread spectrum it can significantly reduce the EMI Electro Magnetic Interference generated by the system Command Rate Auto This item allows users to set command rate Genuine Intel R CPU 0 3 00GHz This is display only field and displays the information of the CPU installed in your computer Processor Speed 3000MHz This item shows the CPU speed Total Memory 2048MB DDR3 1066 This item shows the total momery of DDR3 CPU Current Voltage 1 212V This item diplays the CPU current voltage VAXG Voltage 0 468V This item displays the current VAXG voltage VDIMM 1 548V This item displays the current VDIMM voltage 44 Chapter 3 BIOS Setup Utility Boot Setup Page This page enables you to set the keyboard NumLock state Aptio Setup Utility Copyright C 2010 American Megatrends Inc EIC L Is ES EL Boot Eifel itis mest I A Boot Configuration Selectthe keyboard NumLock state B ion Prioriti oot Option Priorities oa 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Opti
27. figu ration information or you can hold down the Page Up key while rebooting your computer Holding down the Page Up key also clears the setup information You can run the setup utility and manually change the configuration You might need to do this to configure some hardware installed in or connected to the motherboard such as the CPU system memory disk drives etc Running the Setup Utility Every time you start your computer a message appears on the screen before the operating system loading that prompts you to Hit lt DEL gt if you want to run SETUP Whenever you see this message press the Delete key and the Main menu page of the Setup Utility appears on your monitor Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main E G ET o IIS TEUS ISO Er CY 214 BIOS Information Choose the system default language System Data Mon 12 27 2010 System Time 21 54 45 Select Screen L Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc You can use cursor arrow keys to highlight anyone of options on the main menu page Press Enter to select the highlighted option Press the Escape key to leave the setup utility Press to modify the selected field s values 20 Chapter 3 BIOS Setup Utility Some options on the main menu pa
28. ge lead to tables of items with installed values that you can use cursor arrow keys to highlight one item and press PgUp and PgDn keys to cycle through alternative values of that item The other options on the main menu page lead to dialog boxes requiring your answer OK or Cancel by selecting the OK or Cancel key If you have already changed the setup utility press F10 to save those changes and exit the utility Press F1 to display a screen describing all key functions Press F9 to load optimtimal settings Main Setup Page This page displays a table of items defining basic information of your system Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main E G YE C o i EI SE TEUS IS Er WR 8214 BIOS Information Choose the system default language System Data Mon 12 27 2010 System Time 21 54 45 Select Screen Tl Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc Multi Language BIOS Multi language BIOS allows you to see and set up the BIOS with your native language It helps Non English users to solve the problem of setting up the BIOS and achieve extra system performance easily Date amp Time The Date and Time items show the current date and time on the computer If you are running a Windows OS these items are automatical
29. he DIMM module into the socket and press it firmly down until it is seated correctly The socket latches are levered upwards and latch on to the edges of the DIMM 4 Install any remaining DIMM modules For reference only Note Due to the DRAM maximum size is 4 GB at present the memory maximum size we have tested is 8 GB 11 Motherboard User s Guide Jumper Settings Connecting two pins with a jumper cap is SHORT removing a jumper cap from these pins OPEN CLR_CMOS CLR_CMOS Clear CMOS Jumper Use this jumper to clear the contents of the CMOS memory You may need to clear the CMOS memory if the settings in the Setup Utility are incorrect and prevent your motherboard from operating To clear the CMOS memory disconnect all the power cables from the motherboard and then move the jumper cap into the CLEAR setting for a few seconds I Function Jumper Setting ps Short Pins 1 2 Clear CMOS Short Pins 2 3 Note To avoid the system unstability after clearing CMOS we recommend users to enter the main BIOS setting page to Load Optimal Defaults and then Save Changes and Exit 12 Chapter 2 Motherboard Installation Installthe Motherboard Install the motherboard in a system chassis case The board is a Micro ATX size motherboard You can install this motherboard in an ATX case Make sure your case has an I O cover plate matching the ports on this motherboard Install the motherboard in a case
30. hows the information of Memory Multiplier Configuration Memory Multiplier 10 67 This item determines the operation of DDR SDRAM memory CAS colulmn address strobe It is recommanded that you leave this item at the default value The 2T setting requires faster memory that specifically supports this mode 42 Chapter 3 BIOS Setup Utility Memory Timing Configuration This item shows the information of Memory Timing Configuration CAS Latency tcl 8 This item determines the operation of DDR SDRAM memory CAS colulmn address strobe It is recommanded that you leave this item at the default value The 2T setting requires faster memory that specifically supports this mode Row Precharge Time tRP 8 This item specifies Row precharge to Active or Auto Refresh of the same bank RAS to CAS Delay tRD 8 This item specifies the RAS to CAS delay to Rd Wr command to the same bank RAS Active Time tRAS 20 This item specifies the RAS active time Initate Graphics Adapter This item shows the information of Intel Graphics Configutation GT OverClocking Disabled This item allows you to control the internal GFX Turbo mode Graphics Current Normal This item shows the information of the Graphics Current Graphics Core Ratio Limit 22 This item shows the information of the Graphics Core Ratio Limit Press lt Esc gt to return to the Performance Tunning page Press lt Esc gt to return to the Tweak S
31. ican Megatrends Inc ME Version 7 0 2 1164 This item shows the ME version ME Subsystem Enabled This item allows you to enable or disable ME subsystem Press lt Esc gt to return to the Chipset Setup page 38 Chapter 3 BIOS Setup Utility TWEAK Setup Page This page enables you to set the clock speed and system bus for your system The clock speed and system bus are determined by the kind of processor you have installed in your system Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main Advanced Chipset airl Boot Security Save amp Exit Tweak Integrated Clock Chip Parameters gt Memory Voltage Control gt Performance Tuning B O M P Technology Enabled Auto Detect DIMM PCI Clk Enabled Spread Spectrum Enabled Select Screen Command Rate Auto 11 Select item Enter Select Genuine Intel R CPU 0 3 00GHz Change Opt Processor Speed 3000 MHz F1 General Help Total Memory 2048 MB DDR3 1066 F2 Previous Values CPU Current Voltage 1 212V F3 Optimized Defaults VAXG Voltage 0 468V F4 Save amp Exit VDIMM 1 548V ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc gt Integrated Clock Chip Configuration Scroll to this item to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc MEM CEU Suq Tweak E E AR Integrated Clock Chip Configuration Integrated Clock Chip Enabled Di
32. lling please wear a grounded wrist strap if possible If you don t have a wrist strap discharge static electricity by touching the bare metal of the system chassis 3 Carefully hold this motherboard by its edges Do not touch those compo nents unless it is absolutely necessary Put this motherboard on the top of static protection package with component side facing up while installing Pre Installation Inspection 1 Inspect this motherboard whether there are any damages to components and connectors on the board 2 If you suspect this motherboard has been damaged do not connect power to the system Contact your motherboard vendor about those damages Copyright 2011 All Rights Reserved P63G Series V1 0 March 2011 Motherboard User s Guide Table of Contents Trademark orne svesescvsseneeesesods seusaseassdsosessepvannsaatovctesenvasien Statie ELECIPICILY PHECAULIONS C usnu u EEAS eD iaa hina EAE Iiae i Pre Installation INSPeCtiOMssccvescecsssiversscaesssiasnsacveseysvsdteisrsaserevavacdasssessansvetaysavatetavaeisesients i Chapter 1 Introduction U u u u U u u u 1 Key Boqietin q u uni Sa anun LTO sasa Wabha aa a aypa tusa Package Contents Chapter 2 Motherboard Installation 5 Motherboard Components sscvecevescscaasavccescsscsuxavevetisesestvccesesessavvccsnsasesvvevesesssanvaveesecssaveas VO POTS
33. logy CPU e One PCI Express x16 Gen2 port supporting up to 5 GB s direction peak bandwidth Hyper Threading technology enables the operating system into thinking it s hooked up to two processors allowing two threads to be run in parallel both on separate logical processors within the same physical processor Note Due to the DRAM maximum size is 4 GB at present the memory maximum size we have tested is 8 GB Motherboard User s Guide Chipset The Intel H61 Chipset is a single chip with proven reliability and performance e High performance Host Interface Supports the LGA1155 socket for latest 2 Generation Intel Core Family processors e System Memory Controller Support DDR3 SDRAM with up to maximum memory of 16 GB e Support two PCI Express x1 slots Integrade Serial ATA Host Controller with Data transfer rates up to 3 0 Gb s e Serial Peripheral Interface SPI support e Integrated Graphics Support with PAVP 1 5 e Intel High Definition Audio Controller e USB 2 0 Integrated USB 2 0 interface supporting up to eight functional ports Memory Support e Two 240 pin DIMM sockets for DDR3 1333 1066 SDRAM with Dual channel architecture e Maximum installed memory is 16 GB Expansion Slots e One PCI Express x16 slot e Two PCI Express x 1 slots Serial ATA e Serial ATA Controller e Transfer rate exeedig best ATA 3 0 Gb s with scalability to higher rates e Low pin count for both host and devices
34. lue unite Enter Select CPU Fan Full Speed Offset 23 Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc CPU SMART FAN Control Enabled This item allows you to enable disable the control of the CPU fan speed by chang ing the fan voltage 23 Motherboard User s Guide SMART Fan Mode Normal This item allows you to select the fan mode Normal Quiet Silent or Manual for a better operation environment If you choose Normal mode the fan speed will be auto adjusted depending on the CPU temperature If you choose Quite mode the fan speed will be auto minimized for quiet environment If you choose Silent mode the fan speed will be auto restricted to make system more quietly If you choose Manual mode the fan speed will be adjust depending on users parameters SMART Fan start PWM value 180 This item is used to set the start PWM value of the smart fan SMART Fan start TEMP 30 This item is used to set the start temperature of the smart fan DeltaT 3 This item specifies the range that controls CPU temperature and keeps it from going so high or so low when smart fan works SMART Fan Slope PWM value 10 PWM value unite This item is used to set the Slope Select PWM of the smart fan CPU Fan Full Speed Offset 23 This item is used to set the CPU fan full speed offset valu
35. ly processors When choosing a processor consider the performance re quirements of the system Performance is based on the processor design the clock speed and system bus frequency of the processor and the quantity of internal cache memory and external cache memory CPU Installation Procedure Follow these instructions to install the CPU A Opening of the Load Plate Put your thumb on the tail of the load plate and press the tail down Rotate the load plate to fully open position B Disengaging of the Load Lever Hold the hook of lever and pull it to the left side to clear retention tab Rotate the load lever to fully open position C Removing the Cap Be careful not to touch the contact at any time D Inserting the Package E Closing the Load Plate F Fasten the cooling fan supporting base G Make sure the CPU fan is plugged to the Note 1 Note 2 Note 3 Note 4 Chapter 2 Motherboard Installation Grasp the package Ensure to grasp on the edge of the substrate Make sure pin 1 indicator is on your bottom left side Aim at the socket and place the package carefully into the socket by purely vertical motion Rotate the load plate onto the package IHS Intergraded Heat Spreader Engage the load lever while pressing down lightly onto the load plate Secure the load lever with the hook under retention tab onto the CPU socket on the motherboard CPU fan connector Please refer t
36. ly updated whenever you make changes to the Windows Date and Time Properties utility 21 Motherboard User s Guide Advanced Setup Page This page sets up more advanced information about your system Handle this page with caution Any changes can affect the operation of your computer Aptio Setup Utility Copyright C 2010 American Megatrends Inc WEILE Advanced Sin aS US SE LiL SNC DCS Legacy OpROM Support Enable Disable Onboard LAN ties i Option ROM Launch Storage OpROM Enabled p LAN Configuration PPC Health Status Select Screen gt Power Management Setup 11 Select Item gt ACPI Settings Enter Select P CPU Configuration Change Opt gt SATA Configuration F1 General Help gt USB Configuration F2 Previous Values P Super IO Configuration F3 Optimized Defaults gt Trusted Computing F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc Launch PXE OpROM Disabled Use this item to enable or disable the PKE OpROM Launch Storage OpROM Enabled Use this item to enable or disable the Storage OpROM LAN Configuration The item in the menu shows the LAN related information that the BIOS automatically detects Aptio Setup Utility Copyright C 2010 American Megatrends Inc Etim Advanced Kw SS u S Model rN PA LAN Configuration Enable Disable Onboard LAN Controller Select Screen tl Selec
37. mized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc Boot Configuration This item shows the information of the boot configuration Bootup NumLock State On This item determines if the NumLock key is active or inactive at system start up time Boot Option Priorities This item enables you to select boot priorities for all boot devices 45 Motherboard User s Guide Security Setup Page This page enables you to set setup administrator and password Aptio Setup Utility Copyright C 2010 American Megatrends Inc Main Advanced Chipset Tweak Boot Security Save amp Exit If ONLY the Administrator s password is Set Setup Administrator set then this only limits access to Setup Password andis only asked for when entering Setup If ONLY the User s password is set then this is a power on password and must be entered to boot or enter Setup In Setup the Select Screen User will tL Select Item have Administrator rights Enter Select The password must be 3 to20 characters Change Opt long F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc 46 Chapter 3 BIOS Setup Utility Save amp Exit Setup Page This page enables you to exit system setup after saving or without saving the changes Aptio Setup Utili
38. nectors Make sure the latches of the cable and connector are locked into place 4 Remove the hard drive optical drive or DDR memory to determine which of these component may be at fault Maintenance and care tips Your computer like any electrical appliance requires proper care and maintenance Here are some basic PC care tips to help prolong the life of the motherboard and keep it running as best as it can 1 Keep your computer in a well ventilated area Leave some space between the PC and the wall for sufficient airflow 2 Keep your computer in a cool dry place Avoid dusty areas direct sunlight and areas of high moisture content 3 Routinely clean the CPU cooler fan to remove dust and hair 4 In places of hot and humid weather you should turn on your computer once every other week to circulate the air and prevent damage from humidity 5 Add more memory to your computer if possible This not only speeds up the system but also reduces the loading of your hard drive to prolong its life span 6 If possible ensure the power cord has an earth ground pin directly from the wall outlet This will reduce voltage fluctuation that may damage sensitive devices 52 pe s pue SOND Y19 yejsau pue 494205 2M 0 19 uuoo 10 YMS NSd UO UNL But s SOI8 Ajpow Jaye lqelsun Jo Yes 0 ie uu s S VINY Peruo lt wajqoid pueog VW peuo lt Wa qosd pieoq JI pseog 10 Sd YUM tuu qoid
39. o the CPU cooling fan user s manual for more detail installation procedure For reference only To achieve better airflow rates and heat dissipation we suggest that you use a high quality fan with 3800 rpm at least CPU fan and heatsink installation procedures may vary with the type of CPU fan heatsink supplied The form and size of fan heatsink may also vary The fan connector supports the CPU cooling fan of 1 1A 2 2A 26 4W max at 12V Do Not remove the CPU cap from the socket before installing a CPU Return Material Authorization RMA requests will be accepted only if the motherboard comes with the cap on the LGA1155 socket Motherboard User s Guide Installing Memory Modules This motherboard accommodates two 240 pin DIMM sockets for unbuffered DDR3 1333 1066 memory modules and maximum 16 GB installed memory DDR3_1DDR3_2 Note Due to the DRAM maximum size is 4 GB at present the memory maximum size we have tested is 8 GB 10 Chapter 2 Motherboard Installation Memory Module Installation Procedure These modules can be installed with up to 16 GB system memory Refer to the following to install the memory module 1 Push down the latches on both sides of the DIMM socket 2 Align the memory module with the socket There is a notch on the DIMM socket that you can install the DIMM module in the correct direction Match the cutout on the DIMM module with the notch on the DIMM socket 3 Install t
40. oftware you want to install 3 Follow onscreen instructions to install the software program step by step until finished 50 Chapter 5 Trouble Shooting Tips Start up problems during assembly After assembling the PC for the first time you may experience some start up problems Before calling for technical support or returning for warranty this chapter may help to address some of the common questions using some basic troubleshooting tips a System does not power up and the fans are not running 1 Disassemble the PC to remove the VGA adaptor card DDR memory LAN USB and other peripherals including keyboard and mouse Leave only the motherboard CPU with CPU cooler and power supply connected Turn on again to see if the CPU and power supply fans are running 2 Make sure to remove any unused screws or other metal objects such as screwdrivers from the inside PC case This is to prevent damage from short circuit 3 Check the CPU FAN connector is connected to the motherboard 4 For Intel platforms check the pins on the CPU socket for damage or bent A bent pin may cause failure to boot and sometimes permanent damage from short circuit 5 Check the 12V power connector is connected to the motherboard 6 Check that the 12V power amp ATX connectors are fully inserted into the motherboard connectors Make sure the latches of the cable and connector are locked into place b Power is on fans are running but there is no display
41. prosecuted to the maximum extent possible under law Cancel 2 Select the items that you want to setup by clicking on it the default options are recommended Click the Next button to proceed Select Components Select the components you want to install clear the components you do not went to install Components 19654K ja Devices 4725 K Z Applications 37031 K Description Space Required 61412 K Available 1327744K cme 49 Motherboard User s Guide 3 The support software will automatically install Once any of the installation procedures start software is automatically installed in sequence You need to follow the onscreen instructions confirm commands and allow the computer to restart as few times as needed to complete installing what ever software you selected When the process is finished all the support software will be installed and start working Windows Vista 7 will appear below UAC User Account Control message Lo after the system restart You must select Allow to install the next driver Continue this process to complete the drivers installation Bundled Software Installation All bundled software available on the DVD ROM CD ROM is for users conve nience You can install bundled software as follows 1 Click the Utilities button while the Auto Setup screen pops out after inserting the support DVD ROM CD ROM 2 A software menu appears Click the s
42. r defaults Boot Override Use this item to select the boot device 47 Chapter 4 Software amp Applications Introduction This chapter describes the contents of the support DVD ROM CD ROM that comes with the motherboard package The support DVD ROM CD ROM contains all useful software necessary drivers and utility programs to properly run our products More program information is available in a README file located in the same directory as the software To run the support disk simply insert the disk into your DVD ROM CD ROM drive An Auto Setup screen automatically pops out and then you can go on the auto installing or manual installation depending on your operating system If your operating system is Windows XP Vista 7 it will automatically install all the drivers and utilities for your motherboard Installing Support Software 1 Insert the support DVD ROM CD ROM disc in the DVD ROM CD ROM drive 2 When you insert the DVD ROM CD ROM disc in the system DVD ROM CD ROM drive the disk automatically displays an Auto Setup screen 3 The screen displays three buttons of Setup Browse CD and Exit on the right side and three others Drivers Utilities and Information at the top Please see the following illustration fg Mainboard Setup Utility I FT Drivers S Utities 3 information The Setup button runs the software auto installing program as explained in next section 48 Chapter 4 Software
43. rs or AC Decode devices Pin Signal Pin Signal COM Onboard Serial Port Header Connect a serial port extension bracket to this header to add a second serial port to your system F_AUDIO Front Panel Audio Header This header allows the user to install auxiliary front oriented microphone and line out ports for easier access Pn Soa Pm Sg e FOR 6 Sensetreum 7 JES s v O O o Sense return F_USB1 2 Front Panel USB Headers The motherboard has four USB ports installed on the rear edge I O port array Additionally some computer cases have USB ports at the front of the case If you have this kind of case use auxiliary USB header F_USB to connect the front mounted ports to the motherboard 1 USBPWRO USBPWR1 3 USB FP PO USB FP PIC 3 5 USB FP Po 6 USB FP PIO _FP_PO 7 GROUND GROUND 1 Locate the F_USB header on the motherboard Plug the bracket cable onto the F_USB header 3 Remove a slot cover from one of the expansion slots on the system chassis Install an extension bracket in the opening Secure the extension bracket to the chassis with a screw 15 TPM Trusted Platform Module header Trusted platform module TPM is a published specification detailing a micro controllerthat can store secured information and implementations of that specifica tion Signal TPM CLK 11 LADO GND 12 GND LFRAME 13 RESERVEO KEY 14 RESERVE1 LREST VCC
44. sabled ICC OverClocking Lib Version 7 0 0 29 Number of ICC Profiles N A Current ICC Profile Index N A Select Screen l Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc ICC Over Clocking Lib Version 7 0 0 29 This item shows the ICC over clocking lib version 39 Motherboard User s Guide Number of ICC Profiles N A This item shows number of ICC profiles Current ICC Profiles Index N A This item shows current ICC profiles index ICC Enable Disabled This item allows you to enable or disable current ICC Press lt Esc gt to return to the Tweak Setup page gt Memory Voltage Control Configuration Scroll to this item to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc UEM Cu Mees Tweak M r EE Ai Memory Voltage Control CONFIGURATION Memon Voltage Contiol Select Screen 11 Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Memory Voltage Config Auto This item allows users to select memory voltage config Press lt Esc gt to return to the Tweak Setup page 40 Chapter 3 BIOS Setup Utility
45. sion Slots This motherboard has one PCI Express x16 two PCI Express x1 slots PCIEXIO Follow the steps below to install an PCI Express expansion card 1 Locate the PCI Express slot on the motherboard 2 Remove the blanking plate of the slot from the system chassis 3 Install the edge connector of the expansion card into the slot Ensure the edge connector is correctly seated in the slot 4 Secure the metal bracket of the card to the system chassis with a Screw For reference only 18 Chapter 2 Motherboard Installation PCI Express x16 Slot You can install an external PCI Express graphics card that is fully compliant to the PCI Express Base Specification revsion 2 0 PCI Express Slots You can install two external PCI Express graphics cards that are fully compliant to the PCI Express Base Specification revsion 2 0 19 Chapter 3 BIOS Setup Utility Introduction The BIOS Setup Utility records settings and information of your computer such as date and time the type of hardware installed and various configuration settings Your computer applies the information to initialize all the components when boot ing up and basic functions of coordination between system components If the Setup Utility configuration is incorrect it may cause the system to malfunc tion It can even stop your computer booting properly If it happens you can use the clear CMOS jumper to clear the CMOS memory which has stored the con
46. t Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc Onboard LAN Controller Enabled Use this item to enable or disable the Onboard LAN 22 Chapter 3 BIOS Setup Utility Press lt Esc gt to return to the Advanced Menu page PC Health Status On motherboards support hardware monitoring this item lets you monitor the paeameters for critical voltages temperatures and fan speeds Aptio Setup Utility Copyright C 2010 American Megatrends Inc WEE Advanced Reil Su SS Sk LACM de PC Health Status CPU Fan Speed 4687 RPM 7 CPU Voltage 1 212V Select Screen DIMM Voltage 1 548V tl Select Item VAXG Voltage 0 468V Enter Select Change Opt F1 General Help F2 Previous Values PECI Mode F3 Optimized Defaults Offset to TCC Activation Temp 21 F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc gt Smart Fan Function Scroll to this item and press lt Enter gt to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc WEE Advanced SIE SZ US QU EE Na 28 SMART Fan Mode Normal SMART Fan start PWM value 180 SMART Fan start PWM TEMP 30 Select Screen Delta T 3 tl Select Item SMART Fan Slope PWM value 10 PWM va
47. the super IO chip Aptio Setup Utility Copyright C 2010 American Megatrends Inc Advanced Iw ETIS u SN IST Ver a ba Serial Port 0 Configuration Enable or Disable Serial Port COM Device Settings 10 3F 8h IRQ 4 Change Settings Auto Select Screen t Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 1205 Copyright C 2010 American Megatrends Inc Serial Port Enabled This item allows you to enable or disable serial port Device Settings lIO 3F 8h IRQ 4 This item shows the information of the device settings Change Settings Auto Use this item to change device settings Press lt Esc gt to return to the Super IO Configuration page Press lt Esc gt to return to the Advanced Setup page 30 Chapter 3 BIOS Setup Utility Trusted Computing Scroll to this item and press lt Enter gt to view the following screen Aptio Setup Utility Copyright C 2010 American Megatrends Inc Etim Advanced si SSL SS LV 83211 TPM Configuration Enables or Disables TPM support O S will not show TPM Reset of platform is required Current TPM Status Information NO TPM Hardware Select Screen l Select Item Enter Select Change Opt F1 General Help F2 Previous Values F3 Optimized Defaults F4 Save amp Exit ESC Exit Version 2 02 120
48. ty Copyright C 2010 American Megatrends Inc EI Cium Su ras EU ISU dl Save amp Exit Discard Changes and Exit Save Changes and Reset Discard Changes and Reset Exit system setup after saving the changes Select Screen Save Options t Select Item Save Changes Enter Select Discard Changes Change Opt F1 General Help Restore Defaults F2 Previous Values Save as User Defaults F3 Optimized Defaults Restore User Defaults F4 Save amp Exit ESC Exit Boot Override Version 2 02 1205 Copyright C 2010 American Megatrends Inc Save Changes and Exit This item enables you to save the changes that you have made and exit Discard Changes and Exit This item enables you to discard any changes that you have made and exit Save Changes and Reset This item enables you to save the changes that you have made and reset Discard Changes and Reset This item enables you to discard any changes that you have made and reset Save Options This item enables you to save the options that you have made Save Changes This item enables you to save the changes that you have made Discard Changes This item enables you to discard any changes that you have made Restore Defaults This item enables you to restore the system defaults Save as User Defaults This item enables you to save the changes that you have made as user defaults Restore User Defaults This item enables you to restore use
49. uo paun S YMS NSd pue paggnjd s pod Jamod 3V SOINDY19 01 p u 10343 dM S SOW uu lqo1d QAH nssl 3IA p jesaydiiad VINY Deluo2 Jeg JI Ye soJ pue SOND 312 e dsip seu Jolluoui 41994 p 15 1 p JOU VOA sd q poys g pue d q 8uo T JI aunjey Aow wu 10 p lu su Ajjadoud jou Aiowaw WIIG sd q Hous Jl Dd 94 HeJS Y U 19S 1SOd 18 YEH payauuos s ejds p sey soyuow ji 9943 Jamod AZT NdI J punos daag Auy pays pue SOND 815 Bupjiom s NSd tun ddng samog Ji X29493 ON HeIS 0 S e Jd 1nq p ss id s uonng Jamog JieuS3Ao 4 Sunoous qnoa 3Seq

PC CHIPS P63G (V1.0) motherboard

Contents

Download Pdf Manuals

Related Search

Related Contents