Metra XSVI-9003-NAV car kit
Contents
1. METRA ELECTRONICS CORPORATION COPYRIGHT 2010 METRA ELECTRONICS CORPORATION COPYRIGHT 2010 XSVI 9003 NAV INSTALLATION INSTRUCTIONS NOTE ASWC SOLD SEPERATELY IMPORTANT Before beginning any of the following disconnect the nega tive battery terminal to prevent accidental short circuit In the Volkswagen vehicles listed on back there are no 12 volt accessory wires in the factory radio harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 9003 NAV is designed to provide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermar ket radio The R A P Retained Accessory Power function is retained by the XSVI 9003 NAV Along with OE equipped steering wheel controls using the steering wheel control output of the aftermarket radio if equipped The XSVI 9003 NAV also provides essential wires required for aftermarket ra dios that have navigation Provided is VSS Vehicle Speed Sense Reverse and Parking Brake This cuts down the installation time since the installer does not have to look for these wires in the vehicle Wiring the XSVI 9003 NAV Wiring up the XSVI 9003 NAV is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio N2. APPLICATIONS VOLKSWAGEN e CC 2009 10 e EOS 2007 10 e Golf Double Din models only 2002 e Golf 2003 06 e Golf 2010 e GLI 2008 10 e GTI 2002 e Jetta Double Din models only 2002 10 e Jetta 2003 10 e Passat 2002 10 e Rabbit 2007 09 e Tiguan 2009 10 INSTXSVI 9003 NAV REV 06 28 10 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 APPLICATIONS VOLKSWAGEN e CC 2009 10 e EOS 2007 10 e Golf Double Din models only 2002 e Golf 2003 06 e Golf 2010 e GLI 2008 10 e GTI 2002 e Jetta Double Din models only 2002 10 e Jetta 2003 10 e Passat 2002 10 e Rabbit 2007 09 e Tiguan 2009 10 INSTXSVI 9003 NAV REV 06 28 10 1 800 221 0932 www metraonline com APPLICATIONS VOLKSWAGEN e CC 2009 10 e EOS 2007 10 e Golf Double Din models only 2002 e Golf 2003 06 e Golf 2010 e GLI 2008 10 e GTI 2002 e Jetta Double Din models only 2002 10 e Jetta 2003 10 e Passat 2002 10 e Rabbit 2007 09 e Tiguan 2009 10 INSTXSVI 9003 NAV REV 06 28 10 1 800 221 0932 www metraonline com METRA ELECTRONICS CORPORATION COPYRIGHT 2010 APPLICATIONS VOLKSWAGEN e CC 2009 10 e EOS 2007 10 e Golf Double Din models only 2002 e Golf 2003 06 e Golf 2010 e GLI 2008 10 e GTI 2002 e Jetta Double Din models only 2002 10 e Jetta 2003 10 e Passat 2002 10 e Rabbit 2007 09 e Tiguan 2009 10 INSTXSVI 9003 NAV REV 06 28 10 1 800 221 0932 www metraonline com
3. already Do not plug in the ASWC into the XSVI harness yet Initialize the XSVI interface With all connections made and harnesses connected to the vehicle turn the ignition key to the ON position for thirty seconds then turn the key off After the XSVI is initialized plug in the ASWC and refer to the ASWC instructions
4. avigation wire colors Blue Pink VSS Vehicle Speed Sense Green Violet Reverse Lt Green Parking Brake Once all connections have been made plug in the aftermarket radio if not done already Do not plug in the ASWC into the XSVI harness yet Initialize the XSVI interface With all connections made and harnesses connected to the vehicle turn the ignition key to the ON position for thirty seconds then turn the key off After the XSVI is initialized plug in the ASWC and refer to the ASWC instructions XSVI 9003 NAV INSTALLATION INSTRUCTIONS NOTE ASWC SOLD SEPERATELY IMPORTANT Before beginning any of the following disconnect the nega tive battery terminal to prevent accidental short circuit In the Volkswagen vehicles listed on back there are no 12 volt accessory wires in the factory radio harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 9003 NAV is designed to provide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermar ket radio The R A P Retained Accessory Power function is retained by the XSVI 9003 NAV Along with OE equipped steering wheel controls using the steering wheel control output of the aftermarket radio if equipped The XSVI 9003 NAV also provides essential wires required for aftermarket ra dios that have navigation Provided is VSS Vehicle Speed S
5. ense Reverse and Parking Brake This cuts down the installation time since the installer does not have to look for these wires in the vehicle Wiring the XSVI 9003 NAV Wiring up the XSVI 9003 NAV is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio Navigation wire colors Blue Pink VSS Vehicle Speed Sense Green Violet Reverse Lt Green Parking Brake Once all connections have been made plug in the aftermarket radio if not done already Do not plug in the ASWC into the XSVI harness yet Initialize the XSVI interface With all connections made and harnesses connected to the vehicle turn the ignition key to the ON position for thirty seconds then turn the key off After the XSVI is initialized plug in the ASWC and refer to the ASWC instructions XSVI 9003 NAV INSTALLATION INSTRUCTIONS NOTE ASWC SOLD SEPERATELY IMPORTANT Before beginning any of the following disconnect the nega tive battery terminal to prevent accidental short circuit In the Volkswagen vehicles listed on back there are no 12 volt accessory wires in the factory radio harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 9003 NAV is designed to provide a 12 volt 10 amp switched accessory o
6. ning any of the following disconnect the nega tive battery terminal to prevent accidental short circuit In the Volkswagen vehicles listed on back there are no 12 volt accessory wires in the factory radio harness making the installer run an accessory wire to the fuse box or underneath the steering column when installing an aftermarket radio The XSVI 9003 NAV is designed to provide a 12 volt 10 amp switched accessory output along with the rest of the wires needed to install an aftermar ket radio The R A P Retained Accessory Power function is retained by the XSVI 9003 NAV Along with OE equipped steering wheel controls using the steering wheel control output of the aftermarket radio if equipped The XSVI 9003 NAV also provides essential wires required for aftermarket ra dios that have navigation Provided is VSS Vehicle Speed Sense Reverse and Parking Brake This cuts down the installation time since the installer does not have to look for these wires in the vehicle Wiring the XSVI 9003 NAV Wiring up the XSVI 9003 NAV is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio Navigation wire colors Blue Pink VSS Vehicle Speed Sense Green Violet Reverse Lt Green Parking Brake Once all connections have been made plug in the aftermarket radio if not done
7. utput along with the rest of the wires needed to install an aftermar ket radio The R A P Retained Accessory Power function is retained by the XSVI 9003 NAV Along with OE equipped steering wheel controls using the steering wheel control output of the aftermarket radio if equipped The XSVI 9003 NAV also provides essential wires required for aftermarket ra dios that have navigation Provided is VSS Vehicle Speed Sense Reverse and Parking Brake This cuts down the installation time since the installer does not have to look for these wires in the vehicle Wiring the XSVI 9003 NAV Wiring up the XSVI 9003 NAV is like wiring up any other wire harness that would attach to the aftermarket radios harness The Metra EIA wire code can be found on the back of this package that will aid you in the wiring of your aftermarket radio Navigation wire colors Blue Pink VSS Vehicle Speed Sense Green Violet Reverse Lt Green Parking Brake Once all connections have been made plug in the aftermarket radio if not done already Do not plug in the ASWC into the XSVI harness yet Initialize the XSVI interface With all connections made and harnesses connected to the vehicle turn the ignition key to the ON position for thirty seconds then turn the key off After the XSVI is initialized plug in the ASWC and refer to the ASWC instructions XSVI 9003 NAV INSTALLATION INSTRUCTIONS NOTE ASWC SOLD SEPERATELY IMPORTANT Before begin
Download Pdf Manuals
Related Search