Rocstor Rocwave
Contents
1. Step 2 29 30 ROCPOWER Step 3 Step 4 Recycling the Used Battery Contact your local recycling or hazardous waste center for information on the proper disposal of the used batteries 31 32 6 PRODUCT INTRODUCTION General Characteristics True online technology continuously supplies your critical device with a stable regulated transient free pure AC sine wave 1 High efficiency Pulse Width Modulation PWM sine wave topology yields excellent overall performance The high crest factor of the inverter handles all high in rush current loads without the need to upgrade the power rating 2 User friendly Plug and Play design allows hassle free installation All Rocwave units up to 3 000 VA are supplied with input cables and output sockets as standard 3 Built in Maintenance free sealed type battery minimises the need for frequent after Sales service 4 To protect the unit from overloading the UPS will automatically switch to Bypass Mode in 30 seconds if loading is between 105 120 of rated capacity It will automatically switch back to Inverter Mode once the overload ceases 5 Should the output becomes short circuited the UPS puts the system on Stand by Mode provide a visual and audible alarm and cuts the output supply automatically until the short2. 33 Operating Modes amp Voltage System Configurations 34 System Configuration 185 34 Programmable outlet 36 Communication Port Explanation 38 True 5232 Port Descriptions eee 38 USB Port 39 CHAPITER 40 How WOKS 40 UPS System Block Diagram nnns 40 When Utility is NOLMAL swisscncssvcasacivadccssnnacdedanasdvoncuswadsonsecanddasinaedeannnsedes 41 When Utility is Abnormal Absent essen 42 Overload ERE AA 43 CHAPTER S 46 Bundle Software Installation 46 Hardware Installati n nes meson qi tob tatus apa KA A a aa Dana GAN Ga aaa Ma ahaaa 46 Optional Communication 47 RZE 20d 32 CBE OL 47 USE Lr 47 DCE Diy CONIC A 48 SNMP C 49 SNMP WEB 49 SNMP 49 CHAPTER 9 50 Troubleshooting __________ 50 CHAPTER 55
3. 2 gt Ground To enable the EPO function please short Pin 1 amp 2 39 40 NULPUVVER CHAPTER 7 HOW THE UPS WORKS UPS System Block Diagram ACIDC PFC DC AC CONVERTER INVERTER RELA AC INPUT EMI FILTER WA mELAy EMI FILTER AC OUTPUT BATTERY DC DC CHARGER PUSH PULL BATTERY Fig 1 The above illustrates the True On Line Double Conversion architecture of the UPS system The major modules consist of 1 An AC to DC power converter Rectifier with PFC control circuit 2 A DC to AC high frequency power inverter 3 An Intelligent Battery Charger 4 A bank of stationary maintenance free batteries 5 A DC to DC push pull converter control circuit 6 A Static Bypass Loop 7 Input amp Output EMI Filters The table below provides a Summary Guide of the Utility Conditions UPS Operating Modes and the LED Display Indications 41 Utility LEDs Display Utility Normal Utility Abnormal under or over voltage Absent nt or Battery low voltage When Utility is Normal CONVERTER CONVERTER Rectifier converts AC to DC battery is charging Inverter 91 892 LEDs converts DC to and supplies lare illuminated loads with clean amp stable power Rectifier and charger stop operating Battery is looped via the DC DC boosts circuit and provides power to the Inverter LED OFF amp LED Loads continue to receive powe
4. 53 CHAPTER EC 57 LIMITED WARRANTY 57 TECHNICAL 5 4 8 62 Trademarks Acknowledgements 63 sas alan dra 63 Contact Information 64 IMPORTANT SAFETY INSTRUCTIONS PLEASE SAVE THESE INSTRUCTIONS This manual contains important instructions that should be followed during unpacking installation and maintenance of the UPS and batteries Important Notices ensure safety all applications where UPS is hard wired to the electrical supply the connections between the UPS and the electrical supply should be made by a qualified electrical contractor e Those UPS systems supplied with a factory input lead can be safely connected to the wall outlet by the purchaser e The UPS has its own internal energy source battery Should the battery be switched on when no AC power is available voltage will be at the output terminals e Ensure that the AC utility outlet is correctly wired and grounded e Ensure that the input voltage of the UPS matches the supply voltage e Usea certified input power cable with the correct plugs and sockets that matches the voltage system e Donotopen the case as there are no serviceable parts inside Opening the case will void the warranty Any attempt to repair the UPS unit by someone other than an authorized technicia
5. 10 2 Please read the Safety Instructions pages 2 to 3 before installing the UPS Unpacking CAUTION Please be careful when lifting the shipping container or the UPS These items are heavy Improper lifting or movement may cause personal injuries or property damage Take the UPS out of the packing material Retain it for future use e Inspect the UPS for any obvious damage If damage exits IMMEDIATELY contact the hipper e Standard package includes 1 User Manual 2pcs of IEC output cables for UPS with IEC sockets only 1 AC Input Power Cord 1 set of UPS communication software with RS232 cable 1 set of Tower Rack Accessories Kit as below Optional Optional 4 pcs 1 pcs 1 pcs 5 IN 2 pcs 2 pcs 1 6 0 1 0mm 5 8 0 1 0 5 O o o o DOC DOHO A ER U l V VV LIV Installation Location It is necessary to select a proper environment to install the unit in order to minimize the possibility of damage to the UPS and extend the life of the UPS Please follow the instructions below 1 Keep minimum 20cm 8 inches distance clearance from the rear panel of the UPS to avoid any obstructions 2 Do block the air flow to the ventilation opening of the unit 3 Please ensure the installation site is free from excessive dust and the ambient temperature and humidity should be
6. Tower Configuration Setup Y Step 2 ROCPOWER Power Module Battery Module Step 1 fem 7 SN 4 gt a 7 M M 9o r jee 2 RR D gt Y 16 POWE d 1 Rack Mount Configuration Setup Step 1 ns A mm _ caca 7 oo oo uu uu 2 ME Step 2 Step 3 17 ROCPOWER Step 4 Step 5 H HH HH HH HH GE uu uu 18 4 Operational Test LED panel Standard Start Up in Normal AC Mode NOTE Charge the UPS for more than eight 8 hours after unpacking to ensure it is fully charged before use 1 Before commencing the installation please ensure the UPS is properly grounded 2 Ensure that the utilit
7. 4 Error Codes and Their Descriptions Battery weak or faulty Output short circuited EPO Mode UPS overheating Inverter overload Fan out of order EEPROM data error Utility Low 85 170V amp Battery Disconnected Bypass overload EEPROM data does not conform to the Jumper Setting 10 Specifications Agency Approvals 115V Models UL cUL FCC 230V Models 115V 60 70 80 144Vac Voltage Window map 120 140 160 288Vac Base on load percentage 0 33 33 66 66 100 Low Line Transfer Low Line 85Vac Comeback 170Vac High Line Transfer High Line Comeback 50 60 Hz auto select 5Hz Single phase with ground gt 0 99 at full rated linear load Typical Transfer Time 115V AC Leakage current asv 230V fas Surge Protection 9 230 300 joules 115V adjustable to 100 110 115 120 127 115 Voltage 5 230V adjustable to 200 208 220 230 240 Voltage Synchronized 3Hz or 1Hz setting by software 0 1 0 05 0 06Hz unless synchronized to line Factor 53 Harmonic 3 THD Linear Load Distortion lt 7 THD Non Linear Load Transient Response ms lt 60 5 5 Sine Efficiency Battery Mode Full 83 83 85 load Battery System Number of Batteries 3 6 6e Sealed non spillage maintenance free lead Transfer Time AC to DC Zero nverter to Bypass 2 5ms Typical Zero DC Start
8. The UPS is unable to provide backup power 51 If the backup time remains non satisfactory after 8 hours of charging please contact your local dealer for battery replacement Cost of replacement is subjected to the Limited Warranty If the problem persists consult your local dealer for technical assistance Do not use the power strip Replace the wall outlet cable cords plugs Immediately shut down the whole System Disconnect the power to and from the UPS and call for service Check that the battery connectors are fully engaged Allow the batteries to recharge if the batteries are weak If the problem persists after recharging replace the batteries If the problem continues after replacing the batteries consult your local dealer for technical assistance ROCPOWER Note When the Fault LED is illuminated press and hold the Ur key to check the error code The error code is represented by the five LED percent bars 1096 2596 5096 7596 and 10096 Each LED bar represents a number as shown in the figure below For example in the figure below the 2596 LED bar 7596 LED bar amp 100 LED bar are illuminated when the LD key was pressed The error code is 8 2 1 11 Er11 which indicates that the UPS is overheating 10 16 25 8 50 4 100 1 11 77 3 e e gt Level 10 25 50 75 100 lt Cai
9. power your future ROCWAVE Intelligent True On Line UPS User Manual 1 000 2 000 VA 3 000 VA Table of Contents IMPORTANT SAFETY 5 4 CHAPTER nee quM 6 LED Panel Standard 6 LCD panel 8 Symbols on the LCD Display 9 Real Panel DescrIDEIOFS isa aa aka naa KNA 10 CHAPTER 2 a a _ 11 11 instalotion EOC UO 12 Storage 13 MGL 13 CHAPTER 14 E 14 Tower Configuration 5 14 Power Module Battery Module 15 Rack Mount Configuration Setup 16 CHAPTER 18 Operational TESE 18 LED panel Standard sas sasada iga tome AN BEN GAN EU OR GE TEH A NGGON Da Ka Aa Bn 18 Status amp Alarm BUZZG a aiino RES 28 CHAPTER ___ eee 29 Replacing the 29 Recycling the Used 31 CHAPTER T 32 MR RET 32 General Characteristics 32
10. 110V 115V 120V and 127V Drawings U1 U2 and U3 mean the three operation modes of the UPS is Normal Output fixed 50Hz Output or fixed 60Hz Output Drawing V means the Inverter Output may be calibrated at 0 1 1 2 2 3 or 3 27 9 When all the setting changes are completed and Drawing is displayed press the enter key pad to save all the changes The changes will be activated only when the UPS is restarted The LCD screen will be back to the default screen before setting 10 Turn OFF the UPS and the utility input breaker 11 Your Setting changes are complete UPS Shuts Down for Unknown Reasons 1 serious abnormal condition occurs the UPS will turn itself OFF as shown in drawing Y An abnormal message may show in the LCD screen 2 When the UPS turns OFF it may still provide bypass output in most conditions See drawing Z For some special conditions the UPS will lock itself however it may still provide bypass output in most conditions See Drawing Z and an error message will be shown on the screen gt LINE UPS LOAD MINIME z 5 PRL 3 reset the UPS please proceed as followings a Read the error message b See Chapter 9 to troubleshoot the problem If you are unable to reset the UPS consult your local distributor for service c Press the key pad for five 5 seconds buzzer will sound twice 28 4 Turn OFF the utility circuit bre
11. ROCSTOR EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDITIONS NOT STATED IN THIS LIMITED WARRANTY ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW ARE LIMITED IN DURATION TO THE LIMITED WARRANTY PERIOD SOME STATES OR COUNTRIES DO NOT ALLOW A LIMITATION ON HOW LONG AN IMPLIED WARRANTY LASTS OR THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES FOR CONSUMER PRODUCTS IN SUCH STATES OR COUNTRIES SOME EXCLUSIONS OR LIMITATIONS OF THIS LIMITED WARRANTY MAY NOT APPLY TO YOU This Limited Warranty applies to the Rocstor branded hardware products sold by or leased from Rocstor Inc its worldwide subsidiaries affiliates authorized resellers or country distributors collectively referred to in this Limited Warranty as Rocstor This Limited Warranty is applicable in all countries and may be enforced in any country where Rocstor or its authorized service providers offer warranty service subject to the terms and conditions set forth in this Limited Warranty However warranty service availability and response times may vary from country to country and may also be subject to registration requirements in the country of purchase Rocstor warrants that the Rocstor hardware product and all the internal components of the product that you have purchased or leased from Rocstor are free from defects in materials or workmanship under normal use during the Limited Warranty Period The Limited Warranty Period starts on the date of purchase or lease from
12. center Types of Limited Warranty Service Your Rocstor Limited Warranty consists of repair or replacement of defective parts identified by the Rocstor Support Organization as pre failure Carry in Limited Warranty Service Available Monday Friday Under the terms of carry in service you may be required to deliver your Rocstor product to the Rocstor Service Center or an authorized service location for warranty repair You must prepay any shipping charges insurance taxes or duties associated with transportation of the product You are responsible for insuring any product shipped or returned for service You assume risk of loss during shipping 62 Service Upgrades Rocstor offers extra coverage for your product For information on service upgrades visit www Rocstor com Service upgrades purchased in one country are not transferable to another country Manual Disclaimer Revisions to this manual occur periodically Please go to the Rocstor website www rocstor com to obtain the most current version of the User Manual Rocstor is not responsible for any errors or omissions or for the results obtained from the use of the information contained in this manual All information in this manual is provided with no guarantee of completeness accuracy and without warranty of any kind express or implied including but not limited to warranties of the completeness accuracy or currency of this information nor its suitability for any p
13. 130 Programmable outlet setting The UPS is equipped with two 2 programmable outlets for less critical loads These outlets can be disabled during back up modes or overload conditions to provide power to the more critical loads connected to the UPS Click on the Programmable outlet setting bar to enter the outlet settings screen as shown below Outlet Scheme Programmable Outlet Settings Programmable Outlet 1 DES DNE Outlet Turm On After UPS Second 09 3600 Outlet Turn Off After AC Failure Second 0 3600 Outlet Turn On After AC Recovery Second 10 36001 Outlet Turn Off hen Battery Low 25120 80 Outlet Turn Off when UPS Overload Setting Programmable Outlet 2 1 Outlet Turn On After UPS Second 09 3600 Outlet Turn Off After AC Failure Second 10 26001 Outlet Turn On After AC Recovery Second 09 3600 Outlet Turn Off hen Battery Low 2120 80 Outlet Turn OT when UPS Overload Setting Manual Control Switch Programmable Outlet 1 1 rPFrogramrmable Outlet 2 On OFF On 37 Outlet Turns after UPS is select the time to automatically enable this outlet within the specified time when the UPS is powered ON If O seconds is selected the outlet willbe enabled once the UPS is powered ON Outlet Turns OFF After AC Failure select th
14. Rocstor Your dated sales or delivery receipt showing the date of purchase or lease of the product is your proof of the purchase or lease date You may be required to provide proof of purchase or lease as a condition of receiving warranty service You are entitled to warranty service according to the terms and conditions of this document if a repair to your Rocstor branded hardware is required within the Limited Warranty Period This Limited Warranty extends only to the original purchaser or lessee of this Rocstor branded product and is not transferable to anyone who obtains ownership of the Rocstor branded product from the original purchaser or lessee Rocstor products are manufactured using new materials or new and used materials equivalent to new in performance and reliability Spare parts may be new or equivalent to new Spare parts are warranted to be free from defects in material or workmanship for thirty 30 days or for the remainder of the Limited Warranty Period of the Rocstor hardware product in which they are installed whichever is longer 57 This Limited Warranty is provided by Rocstor for Rocpower lines of products used in the ordinary course of your business Descriptions Drawings and Specifications Rocstor products will substantially conform to the descriptions drawings and specifications published by Rocstor However the descriptions drawings and specifications are not warranties of performance and not warranties of fitness
15. es elf Diagnostics ront Panel By button of the panel or Software Control Load Level Battery Level Battery Mode Normal Mode Bypass Mode Self Test Weak Bad Battery Site Wiring Fault Fault Overload Programmable Outlet1 Programmable Outlet2 m ON Button OFF Button Test Alarm Reset Button rotection lt 10596 continuous gt 106 120 for 30 seconds transfer to bypass Overload gt 121 150 for 10 seconds transfer to bypass gt 150 immediately transfer to bypass Buzzer continuously alarms 54 55 Battery lt 105 continuous gt 106 120 for 30 seconds shuts down gt 121 150 for 10 seconds shuts down gt 150 immediately shuts down Buzzer continuously alarms Bypass Mode lt 105 continuous gt 106 12096 for 250 seconds shuts down gt 121 13096 for 125 seconds shuts down gt 13196 13590 for 50 seconds shuts down gt 136 145 for 20 seconds shuts down gt 146 148 for 5 seconds shuts down gt 149 15796 for 2 seconds shuts down gt 158 176 for 1 seconds shuts down gt 17796 187 for 0 32 seconds shuts down gt 188 for 0 16 seconds shuts down Buzzer continuously alarms Bypass Mode Input Fuse Input Breaker Normal Mode Output Breaker Electronic Circuit Battery Mode Output Breaker Electronic Circuit attery ABDM PO UPS shuts down immediately AMA Transfer to By
16. for a particular purpose The descriptions drawings and specifications are subject to this limited warranty Rocstor s Obligation under the Warranty During the Limited Warranty Period Rocstor will repair or replace the defective component parts or the hardware product All component parts or hardware products removed under this Limited Warranty become the property of Rocstor The replacement part or product takes on either the Limited Warranty status of the removed part or product or the thirty 30 day limited warranty of the spare part In the unlikely event that your Rocstor product has a recurring failure Rocstor at its discretion may elect to provide you with a replacement unit of Rocstor s choosing that is at least equivalent to your Rocstor branded product in hardware performance Rocstor reserves the right to elect at its sole discretion to give you a refund of your purchase price or lease payments less interest instead of a replacement This is your exclusive remedy for defective products The original Limited Warranty is not extended when the product or a part of the product is repaired or replaced during the Limited Warranty period Rocstor does not warrant that the operation of this product will be uninterrupted or error free Rocstor is not responsible for damage that occurs as a result of your failure to follow the instructions that came with the Rocstor branded product This Limited Warranty does not apply to expendable par
17. the Programmable Outlet 1 amp Programmable Outlet 2 5 Steady Amber LED indicates Bypass Input is normal ups Fault LED 0 UPS ON Alarm Silence UPS OFF Switch 9 Special functions log in out Go to next page a Go to previous page or change the setting of the UPS 9 re confirm the change of UPS Setting O Manual Bypass Press and OD up KEY key simultaneously for approximately three 3 seconds to transfer from Inverter to Bypass Mode the bypass LED continuously blinks and the buzzer will beep intermediately or transfer from Bypass to Inverter when the UPS is on Line Mode and the Bypass Voltage is Normal Symbols LCD Display Panel Utility or Bypass Source or Bypass Source ee ewe om o memi NE UPS LOAD 4 Digit Measurement Display EM Indicate the item desired to be measured 22 5 BateyWeskorDead me Real Panel Descriptions USB Port RS232 Port Emergency Power Off EPO Dry Contact Signal inputs Communication Card Options Slot External Battery Connector AC power connection socket AC Outlets Two programmable outlets Utility Input circuit breaker 10 Cooling Fans 11 Output circuit breaker for two 2 outlets 12 Output circuit breaker for two 2 programmable outlets CON BB
18. the UPS is able to provide DC back up Otherwise consult your local dealer 2 Disconnect some non critical loads from the UPS output until the overload ceases Check if there is any short circuit 2 Overload 9 between cables such as broken insulation Replace the cables if necessary 3 Remove any objects obstructing the ventilation louvers Verify that the cooling fans are working properly 3 Er11 UPS Overheating Contact your local dealer to replace the fans if necessary 4 Verify that the Live hot OK Neutral wires of the utility AC have been attached correctly Does Ground Neutral 4 Site wiring Ground Voltage exceed acceptable limit fault 5 Verify that the ventilating fans are functioning properly Do not attempt to replace the fans by yourself Contact your local dealer for replacement 5 Er14 Fans out of order 6 Consult your local dealer for assistance 6 Other error codes UPS fails to provide battery backup or its back up time is shorter than its UPS is normal but Check if all power cables there is no Output properly connected the load The UPS switches to Is any power strip is Battery Mode then to the UPS back to Utility Mode Verify that wall outlet is when the connected functioning and all power device is turned ON cords plugs and cables Or the UPS switches lare working back and forth between Battery and Utility Modes Strange noise and smell
19. the original purchaser and declares that the product has not been sold leased bartered or otherwise changed possession The buyer must notify Rocstor and show proof of notification through any reasonable means of communication in which there is acknowledgment of receipt See full street address email address and toll free phone numbers below The notification shall identify any defect malfunction or nonconformity promptly upon discovery Rocstor will acknowledge receipt of the communication and issue Return Merchandise Authorization code The 15 obligated to securely and safely package the product preferably in the original packing materials WITH THE RMA code on the shipping label and deliver it together with a copy of the original purchase receipt and a description of the problem to the Rocstor home office Buyer is responsible for the product until it is received by Rocstor It is recommended that the product be insured during transportation NOTICE The individual user should take care to determine prior to use whether this device is suitable adequate or safe for the use intended Since individual applications are subject to great variation Rocstor makes no representation or warranty as to the suitability or fitness of these products for any specific application Limitation of Damages Liability IF YOUR ROCSTOR BRANDED HARDWARE PRODUCT FAILS TO WORK AS WARRANTED ABOVE THE ORIGINAL PURCHASER S SOLE AND EXCLUSI
20. with overload protection 5 overload capacity is illustrated by the graph and table below sec Load DE 131 135 135 6 448 158 176 176 Delay Time 125 0 32 Sec Inverter Failure Output Load Short Circuited when power is supplied via the Inverter If the output load is short circuited while being supplied via the inverter the UPS will automatically shutdown the inverter and stop power to the loads The fault LED lights up and the buzzer will continuously beep The UPS will not automatically switch ON after short circuit condition is eliminated The UPS has to be manually restarted see page 20 Start Up in Normal Mode ID CONVERTER DC DG CONVERTER Fig 5 45 Inverter Internal Overheating If the UPS experiences overheat when the utility is normal it will switch to Bypass Mode The UPS will switch back to Inverter Mode when the overheating is eliminated If it happens when the utility is abnormal the buzzer will beep continuously and the fault LED will light up The output of the UPS will also be shut OFF Inverter Over current and Inverter Output Voltage Out of tolerance If the UPS inverter delivers excessive current and voltage the UPS is out of order The UPS will switch to Bypass Mode when the utility is abnormal The utility LED bypass LED and fault LED will light up If these two 2 conditions occur when the utility is abnormal the UPS will turn
21. 5 00 pm PST Mon Fri excluding holidays Email support Rocstor com Sales Info Hours 8 00 am 5 00 pm PST Mon Fri excluding holidays Email sales Rocstor com Tel 888 877 7716 Fax 818 884 8777 Corporate Government and Academic Customers Our Corporate Sales Team s goal is to help our U S A and Canadian customers find a storage solution that best serves their needs We will help you determine your best purchasing options For more information please contact the appropriate department below or call us at 1 888 877 7716 General sales information sales Rocstor com Corporate sales information corporate sales Rocstor com Educational sales information academic sales Rocstor com Federal State amp Local government sales information government sales Rocstor com Resellers Business Development OEM Partners All Channel National and International Resellers VARs Consultants contact Rocstor Channel Sales In U S call 888 877 7716 Out of USA call 1 818 449 2000 Email reseller_info Rocstor com Thank you for purchasing Rocpower product Rocstor Ver 1009G Notes ROCPOWER ROCWAVE user manual 65 Notes ROCPOWER ROCWAVE user manual 66 Notes ROCPOWER ROCWAVE user manual 67 power ROCPOWER 192321132037003 68
22. 6 25VDC output is put between 9 and pin 10 for five 5 seconds The capacity of each relay contact is 40VDC 25mA Installation Position Optional Slot Flexible signal output for N C Normal Close or N O Normal Open contact by shorting pin 1 2 or pins 2 3 from JP1 5 The shutdown function will be enabled in 1 minute after blackout occurs if pins 1 2 of both CN1 and CN6 are shorted by jumper Or the shutdown function can only be enabled by pins 9 10 of CN3 if the pins 2 3 of both CN1 and CN6 are shorted by jumper ROCPOWER ROCWAVE user manual 49 SNMP Cards SNMP WEB card For installation please refer to the user s manual attached with the card Installation Position Optional Slot SNMP card of Megatec For installation please refer to the user s manual attached with the card Installation Position Optional Slot 9 Troubleshooting 50 When the UPS becomes faulty or malfunctions during operation you may check the fault lists below for possible solutions Should the problem persist please contact your local dealer for assistance Check Items LED Display UPS Fault A LED Read the error code 1 ErO5 Er25 1 Check battery connections Measure see next page for error readings displayed by the various LEDs and verify the fault as follow Battery voltage to ensure batteries are charged Recharge batteries for 8 hours if necessary Simulate utility outage to verify that
23. D Red LED indicates fault or abnormal conditions Red LED indicates Live amp Neutral lines are improperly connected or there is High Neutral Ground voltage 9 Site wiring fault LED 10 Battery Bad Weak LED Green LED indicates successful self test 11 Self Test LED and no abnormal conditions or faults Red LED indicates low battery power or faulty battery bank were found indi 2 UP 12 Outlet2 LED Green LED indicates 2 UPS Outlets are enabled and ready to supply loads 2 LED indi 1 let 13 Outlet1 LED Green indicates 1 UPS Outlet is enabled and ready to supply loads a During Normal Mode Press and hold for 1 sec The 7711 LEDs will function as Load Rate indicators showing 100 75 50 25 or 10 7 11 LEDs of UPS capacity These LEDs will stop illuminating after 10 sec Bars During Battery Mode Press and hold for 1sec The 7711 LEDs will function as Battery Power indicators showing 10096 7596 5096 2596 or 1096 Battery Power remaining These LEDs will stop illuminating after 10 sec ROCPOWER ROCWAVE user manual LCD panel Optional 000006 amp 0 d QD LCD Display 2 Steady Green LED indicates that the utility input voltage is within the operating range of 160VAC 288VAC Flashing Green LED indicates that the utility input voltage is within the operating range of 120Vac 159Vac 3 Steady Green LED indicates there is output available at
24. OFF the output and the fault LED will light up CHAPTER 8 Bundle Software Installation Guide Hardware Installation 1 Connect the male connector of RS232 USB cable to the UPS communication port 2 Connect the female connector of the RS232 USB cable to a dedicated RS232 port of the Computer 3 For optional interface cards please go to the next page for more details Note Only an RS232 cable is provided with the UPS A USB cable is optional Software Installation Please refer to the user s manual of the bundled software CD ROM for installation guide 46 Optional Communication Cards 2 2nd RS 232 card ROCPOWER ROCWAVE user manual CN1 is 5232 089 For communication protocol please refer to page 39 Installation Position Optional Slot USE USB card CN1 is for USB For communicaiton protocol please refer to page 40 Installation Position Optional Slot 47 48 Dry Contact The assignments of 10 Pin Terminal 11213 15 6 7 10 1 gt UPS Bypass Bypass 2 gt Utility Normal Normal close contact 3 gt Utility Normal Normal open contact 4 gt Inverter On 5 gt Battery Low 6 gt Battery Bad or abnormal 7 gt UPS Alarm 8 gt Common 9 gt Shutdown UPS positive signal 10 gt Shutdown UPS negative signal The shutdown function will be activated after
25. S FOR A FULL DETERMINATION OF YOUR RIGHTS Limitation on the Use of Rocstor Product The product you purchased was not designed for direct or indirect patient care and treatment Do not use this product with any equipment used to directly or indirectly treat or care for a patient CAUTION IF DAMAGED The UPS contains sealed non spillable lead acid batteries The UPS must be recycled or disposed of properly Packages that are crushed punctured or torn such that the contents are revealed should be set aside in an isolated area and must be inspected by a qualified person If the package is not shippable the contents shall be promptly collected and segregated Immediately contact the cosigner or consignee Disclaimer We accept no liability for any loss of data damages and the inability of Rocstor products to work with any third party equipment Nor can Rocstor accept any liability or responsibility for software or third party hardware products Options and Software The Limited Warranty terms and conditions for Rocstor options are as indicated in the Limited Warranty applicable Rocstor options ROCSTOR DOES NOT WARRANTY SOFTWARE PRODUCTS INCLUDING ANY SOFTWARE PRODUCTS OR THE OPERATING SYSTEM PREINSTALLED BY ROCSTOR Rocstor s only obligations with respect to software distributed by Rocstor under the Rocstor brand name are set forth in the applicable end user license or program license agreement Non Ro
26. VE REMEDY SHALL BE REPAIR OR REPLACEMENT ROCSTOR S MAXIMUM LIABILITY UNDER THIS LIMITED WARRANTY 15 EXPRESSLY LIMITED TO THE LESSER OF THE PRICE YOU HAVE PAID FOR THE PRODUCT OR THE COST OF REPAIR OR REPLACEMENT OF ANY ROCSTOR HARDWARE COMPONENTS THAT MALFUNCTION IN CONDITIONS OF NORMAL USE ROCSTOR IS NOT LIABILE FOR ANY DAMAGE TO ANY OTHER PRODUCT CONNECTED TO A ROCSTOR PRODUCT Limitation on Consequential Damages ROCSTOR IS NOT LIABLE FOR ANY DAMAGES CAUSED BY THE PRODUCT OR THE FAILURE OF THE PRODUCT TO PERFORM INCLUDING ANY LOST PROFITS OR SAVINGS OR SPECIAL INCIDENTAL CONSEQUENTIAL OR PUNITIVE DAMAGES ROCSTOR IS NOT LIABLE FOR ANY CLAIM MADE BY A THIRD PARTY OR MADE BY YOU ON BEHALF OF A THIRD PARTY ROCSTOR IS NOT LIABILE FOR ANY DAMAGE TO ANY OTHER PRODUCT CONNECTED TO A ROCSTOR PRODUCT THIS LIMITATION OF LIABILITY APPLIES TO ANY CLAIM FOR DAMAGES OR EQUITABLE RELIEF WHETHER A TORT CLAIM INCLUDING NEGLIGENCE AND STRICT PRODUCT LIABILITY A CONTRACT CLAIM BREACH OF WARRANTY OR ANY OTHER CLAIM THIS LIMITATION OF LIABILITY CANNOT BE WAIVED OR AMENDED BY ANY PERSON THIS LIMITATION OF LIABILITY WILL BE EFFECTIVE EVEN IF YOU HAVE ADVISED ROCSTOR OR AN AUTHORIZED REPRESENTATIVE OF ROCSTOR OF THE POSSIBILITY OF ANY SUCH DAMAGES 59 THIS LIMITED WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS YOU MAY ALSO HAVE OTHER RIGHTS THAT MAY VARY FROM STATE TO STATE OR FROM COUNTRY TO COUNTRY YOU ARE ADVISED TO CONSULT APPLICABLE STATE OR COUNTRY LAW
27. ademarks for company names or products mentioned within the Rocstor site portal pages and articles text manuals Rocstor Rocsecure and Rocpower are registered trademarks of Rocstorage Inc Rocwave Rocforce Smartroc Rocsafe are the trademarks of Rocstorage Inc store your future secure your future and power your future are the slogan marks of Rocstorage Inc Apple the Apple logo Mac Power Macintosh FireWire and Mac Pro Leopard are trademarks of Apple Computer Inc in the United States and other countries Microsoft MS DOS Windows CE Windows NT Windows 98 Soft Windows Vista are registered trademarks of Microsoft Corporation in the United States and other countries Intel Itanium Pentium XXX Celeron and Xeon MMX are registered U S trademarks of Intel Corporation or its subsidiaries in the United States and other countries Novel and is all related marks are registered trademarks of Novell Inc in the United States and other countries Java is a U S trademark of Sun Microsystems Inc Java T and all Java based trademarks and logos are trademarks or registered trademarks of Sun Microsystems Inc in the U S and other countries Netscape and Netscape Navigator are U S trademarks of Netscape Communications Corporation Oracle is a registered U S trademark of Oracle Corporation Redwood City California Sun Sun Microsystems are trademarks or registered trademarks of Sun Microsystems Inc in the U S an
28. aker e The UPS should reset Shutting OFF the UPS 1 Press 9 the key pad for about five 5 seconds The Inverter output will turn OFF The UPS will stop power supply to the outlets and the LCD screen will show Drawing B 2 Turn OFF the utility circuit breaker 3 The UPS is completely turned OFF Status amp Alarm Buzzer The following table helps define the common UPS Status Definitions and Buzzer Beep Descriptions Status Definitions Buzzer Beep Descriptions UPS faulty Inverter shutdown All functions Long Continuous Beep inhabited UPS faulty loads continue to be supplied via Inverter Single successive within 2 sec or Bypass Single short successive beep within Very quick and short successive beep Confirm RS232 port receiving UPS initial start up within 2 successive quick amp short beeps self test repeating 2 sec 2 quick amp short beeps 5 Replacing the Battery ROCPOWER iB E ED vr se UT 100 LI N
29. application Limited Warranty Period The limited warranty period for ROCPOWER UPS products is two 2 years Parts and Labor on the chassis and one 1 year Parts and Labor on the batteries whether inside the chassis or provided separately Rocstor warrants this equipment when properly applied and operated within specified conditions against faulty materials or workmanship for a period of one 1 year from the date of original purchase by the original end user This Limited Warranty extends only to the original purchaser or lessee of this Rocstor branded product and is not transferable For equipment sites within the United States and Canada this limited warranty covers repair or replacement of defective equipment at the discretion of Rocstor Repair will be from the nearest authorized service center Replacement parts and warranty labor will be borne Rocstor For equipment located outside of the United States and Canada Rocstor Inc only covers faulty parts Rocstor products repaired or replaced pursuant to this limited warranty shall be warranted for the unexpired portion of the limited warranty applying to the original product This limited warranty applies only to the original purchaser who must have properly registered the product within 10 days of purchase Customers in Mexico may obtain service under this Limited Warranty only by delivering or shipping the product with all shipping or delivery charges prepaid to an authorized service
30. articular purpose TECHNICAL SUPPORT INFORMATION Technical Support All Rocstor products are backed by free telephone technical support for two 2 years from the date of purchase Please register your product with Rocstor To register fill in the Limited Warranty Registration form in the Support tab at www Rocstor com Free telephone technical support is available weekdays from 9 AM until 6 PM Pacific Standard Time Customers in the United States and Canada can call toll free 888 877 8777 all others must call 818 449 2000 When calling for support please have the product s serial number and system hardware information available Rocstor Replaceable Parts Program Where available the Rocstor Replaceable Parts program ships approved replacement parts directly to you to fulfil your warranty This will save considerable repair time After you call the Rocstor Technical Support Center at 888 877 8777 a replaceable part can be sent directly to you Once the part arrives call the Rocstor Technical Support Center A technician will assist you over the phone to ensure that the installation is quick and easy Limitation on the Use of Any Rocstor Product The product you purchased was not designed for direct or indirect patient care and treatment Do not use this product with any equipment used to directly or indirectly treat or care for a patient 63 Trademarks Acknowledgements O 2008 Rocstorage Inc acknowledges the following tr
31. bjects e Use tools with insulated handles e Wear rubber gloves and boots Do not tools metal parts on top of batteries e Disconnect charging source prior to connecting or disconnecting battery terminals WARNING e This is a Class A UPS Product in a domestic environment e This product may cause radio interference Should this occur the user may be required to take additional measures 1 LED Panel Standard 13 12 11 10 9 8 7 Battery Load Level 10 25 Control Keypads Symbols Functional Descriptions on UPS Power on swich 2 OFF 5j UPS Power Off Switch a Command the UPS to perform self testing b Alarm Silence To mute the alarm buzzer Press amp hold for 1 sec Press OFF key and Self Test key simultaneously for approx 3 seconds to transfer from Inverter to Bypass the bypass LED continuously blinks and the buzzer will beep intermediately or transfer from Bypass to Inverter when the UPS is on Line Mode and the Bypass Voltage is Normal LED Indicators Symbols Functional Descriptions Color LED indicates utility voltage within tolerance 120Vac 280Vac Color LED indicates utility outage or out 5 Battery Mode LED e of tolerance loads supplied by battery power 3 Self Test Alarm Silence Manual Bypass 6 Bypass Mode Color LED indicates bypass supply is LED normal 7 Overload LED SO Red LED indicates UPS is overloaded 8 Fault LE
32. circuit is manually resolved 33 Special Features 1 High Frequency Transformer less technology with rack tower convertible enclosure allows use even in the most difficult of environment with space constraints 2 This UPS is equipped with fully digitalized control logic circuit for greater functionality and enhanced high level power protection Digital signal processing DSP also provides powerful communication capability with enhanced flexibility for easy remote control and monitoring 3 Wide input voltage tolerance from 60V 144V 110V version or 120V 288V 220V version allows under voltage or over voltage correction without unnecessary battery drain and helps extend battery life 4 DC start function ensures the start up of the UPS even during power outages 5 Revolutionary battery management circuit analyzes battery discharge status to adjust battery cut off point and extend battery life 6 Active Power Factor Correction PFC control function constantly maintains the UPS Input Power Factor PF at gt 99 for superb energy efficiency 7 The UPS a Selectable Bypass input voltage tolerance Sensitivity low high to prevent under or over voltage being supplied to the loads during Bypass Mode The selectable Voltage ranges i Sensitivity Low 92 184 130 260 and ii Sensitivity High 97 194 130 260V 8 The UPS has Selectable Output Voltages of 100 110 115 120 127V or 200 208 220 230 240 to meet the needs o
33. cstor hardware and software products are provided AS IS and without any Warranty However non Rocstor manufacturers suppliers or publishers may provide their own warranties directly to you Software Technical Support Software technical support is defined as assistance with questions and issues about the software that was either preinstalled by Rocstor on the Rocstor branded product or that was included with the Rocstor branded product at the time of your purchase or lease of the product Technical support for software is available for the first ninety 90 days from date of product purchase or lease Your dated sales or delivery receipt showing the date of purchase or lease of the product is your proof of the purchase or lease date You may be required to provide proof of purchase or lease as a condition of receiving software technical support 60 After the first ninety 90 days technical support for software that was either preinstalled by Rocstor on the Rocstor branded product or included with the Rocstor branded product at the time of your purchase or lease of the product is available for a fee WARNING The individual user should take care to determine prior to use whether this device is suitable adequate or safe for the use intended Since individual applications are subject to great variation the manufacturer Rocstor makes no representation or warranty as to the suitability or fitness of these devices for any specific
34. d 71 GJ2LEDs will light up after 30 seconds and the buzzer will intermediately to indicate successful power ON 19 Shutdown 1 Shutdown in AC Mode Press the o switch for approximate five 5 seconds until the buzzer beeps The UPS will stop power to the outlets 4 6 72 LEDs will remain illuminated and the ventilating fans will continue to operate Switch OFF the AC power source After 10 seconds the amp 4 22 LEDs will turn OFF and the ventilating fans will stop operating The UPS is now completely shutdown 2 Shutdown in DC Mode Press the o switch for approximately five 5 seconds until the buzzer beeps The UPS will stop power to the outlets After 10 seconds the 574 22 LEDs will turn OFF and the ventilating fans will stop operating The UPS is now completely shutdown Self Testing during AC Mode After the UPS has been successfully started in AC Mode press the switch for approximately five 5 seconds until the buzzer beeps The bA LED will blink to indicate self test in progress If there are no faults or abnormal conditions the LED will stop blinking and will remain illuminated when the self test is completed The v LED will automatically turn OFF 30 seconds after the successful self test Start Up In Normal Mode 1 Ensure that the utility voltage matches the input voltage of the UPS 2 Connect the UPS to the wall outlet of the utility Turn the UPS switch ON The 9 and 27 LEDs will light u
35. d the UPS will supply power to the outputs as indicated in LCD drawing The UPS will automatically turn OFF if the ON switch is pressed within 10 sounds LINE UPS LOAD LOW LINE UPS LOAD A 22 Check Measured Values and Figures detected UPS If you would like to check the measured values and messages please use the scroll up and scroll down Q key pads When you use the scroll down key pad the LCD will display the following sequence Drawing E Input Voltage Drawing J Input Frequency Drawing K UPS Output Voltage Drawing L UPS Output Frequency Drawing M UPS Output Load percentage gt Drawing UPS Battery Voltage gt Drawing UPS inner temperature K LINE UPS LOAD L SUD LOAD L Hz LINE UPS LOAD A c 23 LINE UPS LOAD C LINE UPS LOAD c UPS Default Data and Special Function Execution 1 After the UPS is turned ON successfully use key pad to change the LCD display screen to drawing P1 P1 P2 2 Press the key pad to scroll down LCD screen and then check the UPS settings The LCD will display the following sequence Drawing P1 buzzer gt Drawing 1 self test gt Drawing 1 Bypass Voltage gt Drawing Output Frequency Synchronized Window gt Drawing T Inverter Output Voltage gt Drawing U1 UPS Operation Mode gt Drawing V Outpu
36. d other countries UNIX is a registered trademark of The Open Group Digital Equipment is trademarks of Digital Equipment Corporation registered in the U S and other countries Silicon Graphics is a registered trademark of Silicon Graphics Inc registered in the U S and other countries IBM is trademarks of International Business Machines Corporation registered in the U S and other countries Xerox is registered trademarks of Xerox Corporation registered in the U S and other countries Dell the Dell logo Dimension Inspiron Latitude OptiPlex PowerEdge PowerConnect PowerVault SmartStep and Dell Precision are trademarks of Dell Computer Corporation registered in the U S and other countries All other names are trademarks of their respective companies 2000 2008 Copyrights O 2008 Rocstorage Inc This Manual is protected by United States copyright law and may not be reproduced distributed transmitted displayed published or broadcast without the prior written permission of Rocstorage Inc You may not alter or remove any trademark copyright or other notice from copies of this Manual 64 Contact Information Corporate Headquarters 8130 Remmet Avenue Canoga Park 91304 4129 Office 1 818 449 2000 Fax 1 818 884 8777 Email info Rocstor com Technical Support RMA Tel 888 877 7716 USA and Canada Tel 1 818 449 2000 Domestic and Internationals Fax 1 818 884 8777 Hours 9 00 am
37. emote monitoring of UPS status via PC There are four 4 other optional interface cards available to meet various communication needs i e DCE dry contact relay R2E USE and SNMP WEB card see Chapter 8 The UPS bundled software is compatible with many operating systems such as Windows 98 2000 ME NT XP and Vista For other applications such as Novell NetWare UNIX Linux please contact your local dealer for suitable software All the communication ports including optional cards can be active and used simultaneously to monitor the UPS status However the communication interface with the highest priority has the ability to command and control the UPS The priority of these communication interfaces are as follows Highest Priority in descending order 1 EPO input port 2 Optional Interface card 3 USB 4 RS232 True RS232 Port Descriptions The RS232 interface has been set as follows Baud Rate 2400 bps Data Length 0 Parity The Pin Assignments of the true RS232 port are illustrated as follows Pin 3 RS232 Rx Pin 2 RS232 Tx Pin 5 Ground ON OO USB Descriptions The following is the USB communication protocol definition 1 Comply with USB version 1 0 1 5Mbps 2 Comply with USB HID Version 1 0 3 The Pin Assignments of the USB port 1 gt VCC 5 2 gt 3 gt D 4 gt Ground EPO The Pin assignments of the EPO Input port are 1 gt
38. f various voltage systems 9 The UPS is designed to comply with many stringent international standards for Electromagnetic Interference amp protection EMC 34 Operating Modes amp Voltage System Configurations Download and open the UPS Setting Tool Software to see the screen as below UPS Setting Tool Ver 24100725 system Voltage Selection Voltage Configuration WPS Output voltage Fine Tuning Bypass voltage vvindow Senativity Low oyn Frequency vvindow System Configuration Settings System Voltage Selection Select Input Voltage 110V or 220V Voltage Configurations Select UPS Output Voltage 100V 110V 115V 120V 127V UPS Modes Select Normal CF50 CF60 Mode Output Voltage Fine TuningOutput Voltage Regulation from 0 3 35 Bypass Voltage Windows Sensitivity Select Sensitivity Low Sensitivity High Sensitivity Low Sensitivity High odd 92V 130V 97 130V System Syn Frequency Window Select 3Hz 1Hz Inverter Freq synchronizing range Com Port elect the Com Port of PC Click on Write to confirm the configuration settings The UPS will beep twice to acknowledge setting is successful Turn OFF the UPS after setting is complete to ensure that all the new setting values are written into EEPROM successfully and then re start the UPS to enable the new settings Note CF50 CF60 Frequency Converter Mode 50 to 60Hz or vice versa Sensitivity Low 92 130 High 97
39. is option to automatically disable the outlet within the specified time after the utility outage to provide longer battery back up time for the other more critical loads connected to the UPS Outlet Turns ON After AC Recovers select this option to automatically enable the outlet within the specified time after the utility is restored Outlet Turns OFF When Battery Power is Low select this option to automatically disable the outlet when the remaining battery power capacity is reached during Battery Mode This will prolong battery back up time for the other more critical loads connected to the UPS Outlet Turns OFF When the UPS Detects an Overload select this option to automatically disable the outlet during overload condition Bypass Mode This allows the more critical loads to be continuously supplied via Bypass Mode Select the Settings menu to configure new parameters The new setting is confirmed when the UPS beeps twice Turn OFF the UPS and remove the input source to ensure that the new parameters are successfully written into EEPROM Then re start the UPS to enable the new settings Manual Control Switch Click ON or OFF to manually enabled or disabled the programmable outlets overriding all previous settings 38 Communication Port Explanation The UPS is equipped with EPO dry contacts input true RS232 amp USB Communication ports as standard This provides communication with bundled UPS monitoring software for r
40. me working principle as Figure 2 3 During a utility outage the UPS will work as illustrated in Figure 2 When the battery is low a buzzer will continuously beep until the battery is completely OFF The battery low protection circuit of the UPS will shut OFF the battery supply after a preset threshold to avoid over draining the battery The 2 8 Battery Low LEDs will light up until the UPS is completely shut OFF The UPS will automatically restart when the utility is available 43 Overload Condition The working principle of the UPS when overloaded is illustrated as follows y ACIDE CON V RTER ZEN STATIC Fig 4 1 Generally modern day electronics and IT equipment generate an inrush current when switching on The amount of inrush current varies from equipment to equipment Some can be as high as six 6 times its rated capacity while others produce negligible inrush To prevent severe damage to its inverter caused by the inrush produced by the loads the UPS is equipped with electronics overload protection feature as standard If the UPS loading is gt 105 120 of its capacity it will switch to Bypass Mode 30 seconds to protect the inverter If the overload condition is eliminated by reducing the load to 10596 the UPS will automatically switch back to Inverter Mode If the UPS loading is 15096 of its capacity the inverter will immediately shut down 44 2 The UPS Bypass loop is also equipped
41. n shall void the warranty e To eliminate overheating of the UPS keep all ventilation openings free from obstruction and do not store anything on top of the UPS Keep the UPS 8 inches 20 cm away from the wall e Ensure the UPS is installed within the proper environment as specified 0 40 or 32 40 and 30 9096 non condensing humidity Do not install the UPS in direct sunlight The warranty may be void if the batteries fail e Install the UPS indoors as it is not designed for outdoor use e Dusty corrosive and salty environments can damage the UPS e Install the UPS away from objects which give off excessive heat and areas which excessively wet e Liquids spilled and or foreign objects dropped into the UPS will void the warranty e The battery will discharge naturally if the system is unused for any length of time e The UPS should be recharged every 2 3 months if unused If this is not done the warranty will be void When the UPS is used regularly the batteries will be automatically recharged and kept in top condition e This UPS has been designed and constructed to protect your assets from the wide range of power aberrations experienced on utility power lines Take care to install and maintain the system correctly by your local distributor e Intended for installation in a temperature controlled environment e Servicing of batteries should be performed or supervised by persons knowledgeable about batteries and the re
42. p to indicate the utility and the battery bypass are normal The LCD will change from drawing A to drawing B 20 gt LINE UPS LOAD 3 UPS is on Bypass Mode and will automatically conduct to a self test no abnormal message occurred it means the pre start up of the UPS is successful and the charger is charging the batteries 4 Press the UPS ON switch for approximately three 3 sec The Buzzer will sound twice If the UPS start up is successful the LCD will change from drawing B to drawing C LINE UPS LOAD cow 5 If a failure in self test the LCD will display drawing error code or error status will be shown on the screen LINE UPS LOAD 21 6 Your start up operation of the UPS is now completed as indicated drawing Ensure that the batteries are fully charged by connecting the UPS to a wall receptacle for at least eight 8 hours Start up in Battery Mode Cold Start 1 Ensure that the UPS has already been installed with batteries 2 Press the UPS ON switch for approximately three 3 seconds The buzzer will sound twice The LCD display will change from Drawing A to drawing G LINE UPS LOAD 3 Press the UPS ON switch for approximately three 3 seconds until the LCD display changes from drawing G to drawing H The UPS will now be in Self Test Mode for about 60 seconds When the Self Test Mode is complete
43. pass Mode Overheating UPS shuts down immediately m 7 et Mode Audible Alarm every 3 second Physical Dimensions HxWxD in 88 2U x440x40 88 2U x440x 88 8 2U x440x mm 5 650 650 Ak Weights 34 51b 15 7kg 8 65 31b 29 7kg 115V NEMA 5 15P NEMA 5 20 NEMA L5 30P Input Connection 230 10 IEC 320 10A IEC 320 16A IEC 320 C14 C14 C20 ROCPOWER ROCWAVE user manual 56 5 15Rx2 5 15Rx4 LISV 928 5 20Rx2 5 30Rx1 4 10A IEC 320 C13 6 10A IEC 320 C13 1 16A IEC 320 C19 Output Connection Operation Temperature 0 40 Noise Level lt 50dBA Relative Humidity 0 to 90 Without condensation me Type 1 USB port 1 RS 232 port SNMP option Power ee manager and Windows 95 98 NT 2000 XP Vista Novell NetWare Linux etc IEC EN 62040 1 1 IEC 60950 1 IEC EN 62040 3 IEC EN62040 2 Class A FCC Part 15 Subpart B Class A IEC EN55011 CISPR11 IEC61000 4 2 3 4 5 IEC61000 2 2 IEC61000 3 2 3 CE UL cUL FCC 11 LIMITED WARRANTY This Limited Warranty is provided by Rocstorage Inc hereinafter Rocstor for the Rocstor Rocpower and Rocsecure lines of products General Terms EXCEPT AS EXPRESSLY SET FORTH IN THIS LIMITED WARRANTY ROCSTOR MAKES NO OTHER WARRANTIES OR CONDITIONS EXPRESS OR IMPLIED INCLUDING ANY IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR PARTICULAR PURPOSE
44. quired precautions Keep unauthorized personnel away from batteries e When replacing batteries replace with the same number and type CAUTION Do NOT dispose of battery or batteries in a fire The battery may explode CAUTION Do NOT open or mutilate the battery or batteries Released electrolyte is harmful to the skin and eyes It may be toxic CAUTION Risk of Electric Shock Do NOT remove the cover There are no user serviceable parts Refer servicing to qualified technicians CAUTION Risk of Electric Shock The battery circuit is NOT isolated from AC Hazardous voltage may exist between the battery terminals and ground Test before touching CAUTION A battery can present a risk of electrical shock and high short circuit current CAUTION Keep children away from this product CAUTION HEALTH CARE THE UPS IS NOT TO BE USED IN PATIENT CARE APPLICATIONS The Rocpower product you purchased was not designed for direct or indirect patient care and treatment DO NOT use this product with any equipment used to directly or indirectly treat or care for a patient CAUTION To prevent personal injury or property damage do not carry or move the UPS by the handle or the front cover CAUTION The UPS is designed to be used with computer loads only CAUTION Do NOT connect a laser printer to the UPS outlets The Following precautions should be observed when working on batteries e Remove watches rings or other metal o
45. r illuminated from Inverter The alarm buzzer beeps The UPS now on Battery Mode Rectifier and charger stop operating Battery is looped via the DC DC boosts circuit and provides power to the Inverter I LED OFF amp The alarm buzzer sounds quick LED illuminated amp short beeps indicating battery power low and Inverter power may soon stop RECTIFIER STATE INVERTER 42 The working principle of the UPS under normal utility conditions is illustrated as follows When the utility is normal the AC source is rectified into DC The utility is partially fed into the charger to charge battery and partially fed into the inverter The inverter changes the DC to AC to supply power to the load connected The utility LED and inverter LED light up When Utility is Abnormal Absent The working principle of the UPS under abnormal utility conditions is illustrated as follows ACC CONVERTER STATE SWITCH INVERTER OCC CONVERTER m CHARGER BATTERY Fig 3 1 When the utility is abnormal the UPS will automatically direct the battery power to the inverter and turn OFF the charger and AC DC converter The inverter will immediately change DC to AC to supply power to the output load The amp LED will be illuminated 2 When the utility is back to normal the UPS will turn ON the AC DC converter turn OFF the DC DC converter and switch the charger to Charging Mode It has the sa
46. t Voltage Fine Tuning Sla Ul U2 3 26 Press the scroll up on the key pad to execute special functions The functions include Buzzer ON as drawing Q1 or Buzzer OFF as drawing Q2 Alarm silence for UPS warning and Self Test OFF as Drawing R2 The UPS will execute the battery test for 10 seconds If the Self Test is successful it will show as Drawing W otherwise it will show as Drawing D and error message at the same time LINE UPS LOAD UPS Default Settings and Their Alternatives 1 Ensure the UPS is OFF which means is not in Line Mode or Backup Mode Press the ON Switch and the scroll down key pads simultaneously for approximately three 3 seconds The buzzer will sound twice The LCD screen shows drawing P1 which is the Settings Mode To scroll down the LCD screen see page 23 All default settings may be changed by pressing scroll up key pad except the Buzzer Drawings P1 amp P2 and Self Test Q 1 amp Q2 The bypass input acceptable range it can be 176VAC 264VAC for 220VAC system 88VAC 132VAC for 110VAC system or 187VAC 264VAC for 220VAC system 93 5VAC 132VAC for 110VAC system Drawing S means the acceptable setting values of the bypass frequency Inverter Outputs are 3Hz and 1Hz Drawing T means the acceptable Inverter Output Voltage is 200V 208V 220V 230V or 240V for 220VAC system or 100V
47. ts This Limited Warranty does not extend to any product from which the serial number has been removed or that has been damaged or rendered defective a as a result of accident misuse abuse or other external causes b as a result of normal wear c by operation outside the usage parameters stated in the user documentation that shipped with the product and or posted on the Rocstor website d by the use of parts not manufactured or sold by Rocstor or e by modification or service by anyone other than i Rocstor ii a Rocstor authorized service provider or iii your own installation of end user replaceable Rocstor or Rocstor approved parts if available for your product in the servicing country These terms and conditions constitute the complete and exclusive Limited Warranty agreement between Rocstor and you regarding the Rocstor branded product you have purchased or leased These terms and conditions supersede any prior agreements or representations including representations made in Rocstor sales literature or advice given to you by Rocstor or an agent or employee of Rocstor that may have been made in connection with your purchase or lease of the Rocstor branded product No change to the conditions of this Limited Warranty is valid unless it is made in writing and signed by an authorized representative of Rocstor 58 Buyer s Obligation under the Warranty The person requesting coverage under this warranty shall prove that he or she is
48. within the specified limits 4 Do not place the UPS in a dusty or corrosive environment or near any flammable objects 5 This UPS is not designed for outdoor use ELK 22 Pr rni Relative Humidity 6 condensing 0 90 13 Storage Instructions For extended storage in moderate climate the batteries should be charged for 12 hours every three 3 months by connecting the UPS to the utility supply and switch on input breaker located at UPS rear panel Repeat this procedure every two 2 months if the storage ambient temperature is above 30 C 86 F Maintenance Clean the dust from the ventilation openings and intakes on the rear panel 1 Turn OFF the UPS and wipe the casing with a damp cloth 2 Periodically unplug the UPS power cord from the wall Outlet to test the batteries 3 sure you have already saved all applications before you proceed to the battery discharging capability test ROCPOWER CHAPTER 3 Set up
49. y voltage matches the input voltage of the UPS 3 Connect UPS main power cord to the AC utility power outlet 4 Turn ON the AC power source All of the LEDs on the front panel display will flash once after three 3 seconds except 571 8972 which will remain illuminated Green At the same time the fan at the rear of the UPS will start operating Press the D switch for approximately three 3 seconds to start the UPS The buzzer will beep and the and 04072 LEDs will light up after 30 seconds The start up procedure is completed and the UPS outlets are available It is advisable to perform a Battery Mode Test before connecting the loads to the UPS to ensure the batteries are working properly Switch OFF the AC power source after the UPS had been switched ON The LED on the front panel display will turn OFF while the amp LED will be illuminated The buzzer alarm will beep intermediately indicating the UPS is in Battery Mode Connect a non critical load to the UPS outlets to confirm power from the battery Repeat the test by switching ON and OFF the AC power source to ensure the UPS is functioning properly Start up in Battery Mode Cold Start This UPS can be switched ON for operation without the presence of an AC power source Press and hold the 1 switch until the buzzer beeps then release the switch Within the next 10 seconds press and hold the 1 switch 2 time The UPS shall perform its start up procedure The 2 an
Download Pdf Manuals
Related Search