Tripp Lite 25U SmartRack 4-Post Open Frame Rack - Organize and Secure Network Rack Equipment
Contents
1. oe gt SmartRack 4 Post Open Frame Racks SR4POST SR4P0ST1224 SR4POST13 SR4POST25 Contents Section 1 Parts Identification Section 2 Rack Assembly Section 3 Optional Casters Section 4 Service amp Warranty SAVE THESE INSTRUCTIONS A N This manual contains important instructions and warnings that must be followed during installation Failure to comply may affect the warranty TRIPP LITE 1111 W 35th Street Chicago IL 60609 USA www tripplite com support Copyright 2010 Tripp Lite All trademarks are the sole property of their respective owners 1 Parts Identification After opening the shipping box lay out the parts on a flat surface for identification If anything is missing or damaged go to www tripplite com support for assistance Note SR4POST is shown SR4POST13 amp SR4POST25 are shorter 13U amp 25U respectively and SR4POST1224 uses round threaded equipment mounting holes instead of square holes However the rack assembly process for all 4 models is identical Rack Components EN Left Vertical Rail 2 E Right Vertical Rail 2 4 Base Bracket 2 DJ Bottom Corner Section 4 4 Bottom Center Section 2 F Top Corner Section 4 G Top Center Section 2 H Top Bracket 2 Rack Assembly Hardware Gi ws Acorn Cap Nuts 12 Fl Ms Bolts 16 Ms Washers 28 E Ms Hex Nuts 4 Rack Assembly Tool M us 13 mm Wrench Equipment Mounting Hardware SR4P2. table at right When the sections are aligned at the required depth use an M8 bolt El and M8 washer 7 to fasten each section in place The bolt will pass through the corner section and into threaded holes in the center section Tighten the bolts approximately 90 with the included wrench they should be fixed in place but not completely tightened Note You ll finish tightening all nuts and bolts when the rack is fully assembled Repeat the process in Step 2 1 to assemble the other top section Make sure the depths match by using the same pair of index numbers Lay the assembled sections side by side to confirm that they re the same length E Assemble a bottom section by sliding two bottom corner sections BJ inside the ends of a bottom center section B The index numbers printed on the corner sections correspond to the rack s mounting depth Align the sections so the index numbers match the numbers you used for the top sections When the sections are aligned at the correct depth use two M8 bolts J and M8 washers to fasten each section in place The bolts will pass through the center section and into threaded holes in the corner sections Tighten the bolts approximately 90 with the included wrench Repeat the process in Step 2 2 to assemble the other bottom section Lay the assembled top and bottom sections side by side to confirm that all sections are the same length 2 Rack Assembly continued PE L
3. 8 stud at the end of the assembled top section should pass through the vertical rail first then the top bracket EF Fasten a base bracket IA and right vertical rail EJ to the threaded M8 studs at the end of the assembled bottom section PMB with two M8 acorn cap nuts fl and M8 washers FE Also fasten the base bracket to the threaded M8 studs at the end of the other assembled bottom section with two M8 acorn cap nuts fl and M8 washers a Tighten 90 The threaded M8 studs should pass through the vertical rails first then the base bracket 2 Rack Assembly continued EX Fasten a top bracket EI to the threaded M8 stud at the end of the assembled top section GEV with an M8 acorn cap nut Hf and M8 washer E4 Also fasten the base bracket to the threaded M8 stud at the end of the other assembled bottom section with an M8 acorn cap nut D and M8 washer E4 Tighten 90 The threaded M8 studs should pass through the vertical rails first then the top bracket BEET Place the rack upright on a level surface and confirm that the rack is stable Tighten all nuts and bolts until fully secure If you are installing optional casters follow the instructions in Section 3 then return to this step Mount your equipment in the rack by following the mounting instructions in the manufacturers documentation Note If you require additional stability order Tripp Lite s Bolt Down kit model SRBOLTDOWN sold separately to fasten the rac
4. OST SR4POST13 SR4POST25 Only CT we Cage Nuts Qty varies per model LI pvc Cup Washers Qty varies i M6 Phillips Head Screws Qty varies Equipment Mounting Hardware SR4POST1224 Only L 412 24 Phillios head Screws 50 R Black PVC Washers 50 Ki A White PVC Washers 50 V Grounding Hardware Optional Installation Ei M4 Hex Nuts 2 o T M4 Bolts 2 8 E M4 Washers 2 Cable Management Hardware Optional Installation IM Cable Management Hooks Qty varies Ed Hook Mounting Screws Qty varies 2 Rack Assembly Warning Install the rack in a controlled structurally sound indoor environment with a level floor Use appropriate caution when moving the rack and consider whether you require assistance Assemble the rack completely and confirm its stability before attempting to install equipment in the rack Note SR4POST is shown but the assembly process is identical for SR4POST1224 SR4POST13 amp SR4POST25 Rack Depth Index PEE Assemble a top section by sliding two top corner sections J over the ends of a top center section fe Align the sections so the index Mounting Depth Index Numbers numbers printed on the center section show through the cutouts in the corner sections The index numbers correspond to the rack s mounting depth which is adjustable from 22 inches to 38 inches in 1 inch increments You can set the rack to the required mounting depth by cross referencing the index numbers with the
5. Steps 3 2 through 3 5 until all four casters are mounted securely EFi Insert an M8 bolt Hl into the hole in each bottom corner fasten with an M8 washer Ei and M8 hex nut I and tighten securely The M8 hardware is included with the rack EE Place the rack upright on a level surface and confirm that the rack is stable If you haven t already completed Step 2 10 complete it now 4 Service Warranty amp Warranty Registration Service Your Tripp Lite product is covered by the warranty described in this manual A variety of Extended Warranty and On Site Service Programs are also available from Tripp Lite For more information on service visit www tripplite com support Before returning your product for service follow these steps 1 Review the installation and operation procedures in this manual to insure that the service problem does not originate from a misreading of the instructions 2 If the problem continues do not contact or return the product to the dealer Instead visit www tripplite com support 3 If the problem requires service visit www tripplite com support and click the Product Returns link From here you can request a Returned Material Authorization RMA number which is required for service This simple on line form will ask for your unit s model and serial numbers along with other general purchaser information The RMA number along with shipping instructions will be emailed to you Any damages
6. ay out a left vertical rail EN right vertical rail E assembled top section BAJA and assembled bottom section PMI in a rectangle on the floor or a stable work surface Place all the pieces facedown The assembled top and bottom sections are facedown when the inserted bolt heads are facedown The vertical rails are facedown when the rails are laying flat on the side that has keyhole mounting slots Insert the threaded M8 studs at the ends of the top and bottom sections through the corresponding holes in the vertical rails but do not fasten yet 2 4 Fasten a base bracket to the threaded M8 studs at the end of the assembled bottom section with two M8 acorn cap nuts i and M8 washers E4 Tighten 90 The threaded M8 studs should pass through the vertical rail first then the base bracket 2 5 Fasten a top bracket C to the threaded M8 stud at the end of the assembled top section with an M8 acorn cap nut i and M8 washer E4 Tighten 2 Rack Assembly continued 2 6 Fasten a left vertical rail E and assembled bottom section LAP to the base bracket A with two M8 acorn cap nuts fl and M8 washers E4 Tighten 90 The threaded M8 studs at the end of the assembled bottom section should pass through the vertical rail first then the base bracket Pd Fasten an assembled top section IAJ to the top bracket f and left vertical rail EN with an M8 acorn cap nut ff and M8 washer E4 Tighten 90 The threaded M
7. direct indirect special or consequential to the product incurred during shipment to Tripp Lite or an authorized Tripp Lite service center is not covered under warranty Products shipped to Tripp Lite or an authorized Tripp Lite service center must have transportation charges prepaid Mark the RMA number on the outside of the package If the product is within its warranty period enclose a copy of your sales receipt Return the product for service using an insured carrier to the address given to you when you request the RMA Limited Warranty Seller warrants this product if used in accordance with all applicable instructions to be free from original defects in material and workmanship for a period of 5 years from the date of initial purchase If the product should prove defective in material or workmanship within that period Seller will repair or replace the product in its sole discretion THIS WARRANTY DOES NOT APPLY TO NORMAL WEAR OR TO DAMAGE RESULTING FROM ACCIDENT MISUSE ABUSE OR NEGLECT SELLER MAKES NO EXPRESS WARRANTIES OTHER THAN THE WARRANTY EXPRESSLY SET FORTH HEREIN EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW ALL IMPLIED WARRANTIES INCLUDING ALL WARRANTIES OF MERCHANTABILITY OR FITNESS ARE LIMITED IN DURATION TO THE WARRANTY PERIOD SET FORTH ABOVE AND THIS WARRANTY EXPRESSLY EXCLUDES ALL INCIDENTAL AND CONSEQUENTIAL DAMAGES Some states do not allow limitations on how long an implied warranty lasts and some states do not allo
8. k to the floor SRBOLTDOWN is not compatible with casters PEE Optional Ground Connection Use the included M4 nuts i bolts M and washers MM to fasten a user Supplied ground wire to the rack and to your facility s ground connection There is a ground connection hole at each lower corner of the rack 2 Rack Assembly continued EEF Optional Cable Management Hooks Fasten the included cable management hooks MJ to the vertical rack rails with the included screws K4 3 Optional Casters Warning Do not attempt to install casters while equipment is installed in the rack Note Caster installation requires Tripp Lite s Heavy Duty Rolling Caster Kit model SRCASTER sold separately The kit includes four casters and the M6 hardware required to mount the casters to the bottom of the rack EFT Place the empty rack on its side EP Place a caster EW at one of the bottom outside corners of the rack and line up the holes in the caster with the holes in the rack EY Place an M6 washer EA over an M6 bolt IA and insert the bolt through one of the caster mounting holes in the bottom inside corner of the rack and then through the corresponding mounting hole in the base of the caster EFI Place an M6 washer El and an M6 nut ED over the end of the M6 bolt 4 then tighten 90 3 5 Repeat Step 3 3 and Step 3 4 until all four bolts are in place then tighten all the nuts and bolts until the caster is secure EXI Repeat
9. w the exclusion or limitation of incidental or consequential damages so the above limitations or exclusions may not apply to you This warranty gives you specific legal rights and you may have other rights which vary from jurisdiction to jurisdiction WARNING The individual user should take care to determine prior to use whether this device is suitable adequate or safe for the use intended Since individual applications are subject to great variation the manufacturer makes no representation or warranty as to the Suitability or fitness of these devices for any specific application Warranty Registration Visit www tripplite com warranty today to register the warranty for your new Tripp Lite product You ll be automatically entered into a drawing for a chance to win a FREE Tripp Lite product No purchase necessary Void where prohibited Some restrictions apply See www tripplite com for details Tripp Lite has a policy of continuous improvement Specifications are subject to change without notice TRIPP LITE 1111 W 35th Street Chicago IL 60609 USA www tripplite com support 8 201010142 933046 EN
Download Pdf Manuals
Related Search