Home

Samsung 320MXN-3

1. SelectAll Clear AN Refresh Video Wall Control 4 1 Video Wall A Video Wall is a set of video screens that are connected together so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen 2 Video Wall Control Video Wall properties can be configured EE MDC Video Wall px Close Ivideo Wall NG Format Natural 1 On Off Turns on off the Video Wall function of the selected display 2 Format The format can be selected to see a divided screen e Full e Natural 3 Video Wall Screen divider The screen can be divided into You can select a number of screens with a different layout when dividing Select a mode from Screen divider Select a display from Display Selection The place will be set up by pressing a number in the selected mode The maximum number of monitors that can be arranged Horizontal X Vertical 100 Up to 15 monitors can be arranged in a row The maximum value for Horizontal is 6 if Vertical is set to 15 while the maximum value for Vertical is 6 if Horizontal is set to 15 4 Viewing Screen Splits You can view and change the layout of screens using the Screen Divider settings amp The range of the Screen Divider setting may differ depending on the model You may not operate this function in Magicl nfo The Input source of TV works only on TV model The Maintenance Control function is ava
2. HT TIME OZ348 20 30 UA102 21 10 Appendix Contact SAMSUNG WORLDWIDE Note If you have any questions or comments relating to Samsung products please contact the SAMSUNG customer care center North America U S A 1 800 SAMSUNG 726 7864 http www samsung com CANADA 1 800 SAMSUNG 726 7864 http www samsung com MEXICO 01 800 SAMSUNG http www samsung com 726 7864 Latin America ARGENTINA 0800 333 3733 http www samsung com BRAZIL 0800 124 421 http www samsung com 4004 0000 CHILE 800 SAMSUNG 726 7864 http www samsung com COLOMBIA 01 8000112112 http www samsung com COSTA RICA 0 800 507 7267 http www samsung com ECUADOR 1 800 10 7267 http www samsung com EL SALVADOR 800 6225 http www samsung com GUATEMALA 1 800 299 0013 http www samsung com HONDURAS 800 7919267 http www samsung com JAMAICA 1 800 234 7267 http www samsung com NICARAGUA 00 1800 5077267 http www samsung com PANAMA 800 7267 http www samsung com PERU 0 800 777 08 http www samsung com PUERTO RICO 1 800 682 3180 http www samsung com REP DOMINICA 1 800 751 2676 http www samsung com TRINIDAD amp TO 1 800 SAMSUNG 726 7864 http www samsung com BAGO VENEZUELA 0 800 100 5303 http www samsung com Europe ALBANIA 42 27 5755 AUSTRIA 0810 SAMSUNG 7267864 http www samsung com 0 07 min BELGIUM 02 201 24 18 http www samsung com be Dutch http www samsung com be fr French BOSNIA 05 133 1
3. Connect the Audio cable for your LCD Display to the AUDIO port on the back of the LCD Display Connect the power cord for your LCD Display to the POWER port on the back of the LCD Display Turn on the power switch Note Contact a local SAMSUNG Electronics Service Center to buy optional items Connecting to Other devices Note e AV input devices such as DVD players VCRs or camcorders as well as your computer can be connected to the LCD Display For detailed information on connecting AV input devices refer to the contents under Adjusting Your LCD Display e The LCD Display s configuration at the back may vary slightly depending on the LCD Display model Connecting AV Devices VIDEO VIDEO OUT AVDIC OUT Connections 1 Connect an audio cable to AV COMPONENT AUDIO IN R AUDIO L on the product and the audio port on an external device such as a VCR or DVD player 2 Connect a video cable to AV IN on the product and the video output port on the external device 3 Then start the DVD VCR or Camcorders with a DVD disc or tape inserted 4 Press SOURCE on the product or remote control and select AV Connecting to a Camcorder 1 Locate the AV output jacks on the camcorder They are usually found on the side or back of the camcorder Connect a video cable between the VIDEO OUTPUT jack on the camcorder and the AV IN on the LCD Dis play 2 Connect a set of audio cables between the A
4. Volume e gt Tee Ta Lamp Temp Status 8 8 Sensor Fan Soo RAE ma O50 Display Settings Ye Info Grid shows some basic information necessary to System 1 E Power Status 2 Input 3 Image Size 4 On Timer 5 Off Timer 2 Selects displays you want to adjust using the Select All button or checkboxes Multiple Display Control File Adda Device Remote Control Safety Lock FaultDevice Alet Lamp Control Help nha Faulty Device U Select All Clear All Refresh Idle OSD Display Source OSD Not Optimum Mode OSD No Signal OSD MOC OSD Je Wi System allows controlling some of the functions of the selected display 1 Power On Off Turns the power of the selected display On Off 2 Volume Controls the volume level of the selected display It receives the volume value of the selected display from the sets and displays it in the slider If you deselect a single display or all displays the default value 10 will be restored Mute On Off Turns on off the Mute function of the selected display When selecting one set at a time turn on the Mute function for the selected set The Mute function is disabled automatically when you adjust the volume level The values return to the default settings when you undo the selections or choose Select All UJ The Volume Control and Mute features are available only for the displays whose power status is ON 3 Sele
5. 2 Double click the Display icon 3 Select the Settings tab and click Advanced Properties button 4 Select the Monitor tab 5 Click the Change button in the Monitor Type area 6 Choose Specify the location of the driver 7 Choose Display a list of all the driver in a specific location then click Next button 8 Click the Have Disk button 9 Specify A D driver then click OK button 10 Select Show all devices and choose the monitor that corresponds to the one you con nected to your computer and click OK 11 Continue choosing Close button and OK button until you close the Display Properties dialogue box Microsoft Windows NT Operating System 1 Click Start Settings Control Panel and then double click Display icon 2 In Display Registration Information window click Settings Tab and then click All Display Modes 3 Select a mode that you wish to use Resolution Number of Colors and Vertical frequen cy and then click OK 4 Click Apply button if you see the screen working normally after clicking Test If the screen is not normal change to a different mode lower mode of resolution Colors or frequency Note If there is no Mode at All Display Modes select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide Linux Operating System To execute X Window you need to make the X86Config file which is
6. Je Info Grid shows some basic information necessary to Input Source Control 1 PC Changes the Input Source of the selected display to PC 2 BNC Changes the Input Source of the selected display to BNC 3 DVI Changes the Input Source of the selected display to DVI 4 TV Changes the Input Source of the selected display to TV 5 DTV Changes the Input Source of the selected display to DTV 6 AV Changes the Input Source of the selected display to AV 7 S Video Changes the Input Source of the selected display to S Video 8 Component Changes the Input Source of the selected display to Component 9 Magiclnfo The Input source of Magiclnfo works only on Magiclnfo model 10 HDMI1 HDM12 Changes the Input Source of the selected display to HDMI 11 DP Switches the input source for the selected display to DP 12 Channel Channel arrow appears when the Input Source is TV HDMI2 may not be supported depending on the product amp DP may not be supported depending on the product amp The Input Source Control feature is available only for the displays whose power status is ON TV Source can be selected only in products with TV and controlling channels is allowed only when Input Source is TV EG I mage Size PC BNC DVI DP 1 Click Image Size of the main icons and the Image Size control screen appears Multiple Display Control File AddaDewce Remote Control SafetyLock Faul Device Aler
7. Click lt Back B Mext N gt Finish Cancel When using multiple languages you can choose and set a specific language among them 4 Select Screen Type step 4 iis Magzicinfo Setup Wizard 7 1 09 Select Screen Type step 4 Select i Landscape Portrait click lt Back B Mext N gt Finish Cancel You can select which rotation type will be applied to your device 5 Setup Information Adjusting the LCD Display NG Magicinfo 5etup Wizard v 1 09 Setup Information 1 Application bdagiclnfo Pro LAN WAN based version 2 Internet Protocol T CPP IF 10 885 65 107 3 Language English 4 Screen Type Landscape Ww Do not show again Click 4 Back B Cancel Shows the settings that have been selected by the user Note If the Magiclnfo icon is not displayed on the notification area double click the Magiclnfo icon on the window desktop The icon will appear Troubleshooting Self Test Feature Check Note Check the following items yourself before calling for assistance Contact a Service Center for problems that you cannot solve by yourself Self Test Feature Check 1 Turn off both your computer and the LCD Display 2 Unplug the video cable from the back of the computer 3 Turn on the LCD Display The figure shown below No Signal appears on a black background when the LCD Display is working normally even though no video signal is detected Whi
8. Safety Lock Lock code to be set on TV Monitor 1 ON 0 OFF e Ack Header OM DATA nckiNak r CMD Val mand Length Check Sum OxAA OxEF 3 IN oxsp Safety Lock Safety Lock Same as above e Nak Header SOn DATA Ack Nak r CMD van mand Length Check Sum 3 N oxsp Safety Lock ERR Error code that shows what occurred error is Connections Connecting a Computer There are several ways to connect the computer to the monitor Choose one from the following options 1 1 Using the D sub Analog connector on the video card e Connect the D sub to the 15 pin RGB COMPONENT IN port on the back of your LCD Display and the 15 pin D sub Port on the computer o ae o AGE sr COPIPORENT IH cE Using the DVI Digital connector on the video card e Connect the DVI Cable to the DVI IN port on the back of your LCD Display and the DVI port on the computer Using the D sub Digital connector on the video card e Connect the HDMI IN 1 HDMI IN 2 port on the LCD Display to the HDMI port on the PC using the HDMI cable Connections Mii HO eG INP Note Select HDMI2 or HDMI1 as an input source when connected to the PC via an HDMI cable To obtain normal picture and audio from the PC HDMI2 or HDMI1 must be selected before PC is selected in Edit Name To enable audio when DVI Device is selected be sure to establish the connection using step
9. 3 Ensure that the power plug is plugged into the power outlet firmly and correctly e Otherwise this may result in fire 3 Do not forcefully bend or pull the power plug and do not place any heavy material on it e Otherwise this may result in fire L Do not connect multiple appliances to the same power outlet e Otherwise this may cause fire due to overheating 3 Do not disconnect the power cord while using the product e Otherwise this may result in damage to the product due to electric shock L To disconnect the apparatus from the mains the plug must be pulled out from the mains socket therefore the mains plug shall be readily operable e Otherwise this may cause electric shock or fire J Use only the power cord provided by our company Do not use the provided power cord of another product e Otherwise this may result in fire or electric shock AP Connect the power plug to a wall outlet that can be easily reached e When a problem occurs with the product you must unplug the power plug to cut the power off completely You cannot cut the power off completely using only the power button on the prod uct Be sure to contact an authorized Service Center when installing your monitor in a location with heavy dust high or low temperatures high hu midity and exposed to chemical substances and where it operates for 24 hours such as at airports train stations etc Failure to do so may cause serious da
10. The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance Safety Instructions Notational Power Note These safety instructions must be followed to ensure your safety and prevent property dam age Make sure to read the instructions carefully and use the product in the correct manner E Warning Caution Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment DO Note Important to read and under Prohibited stand at all times Disconnect the plug from the outlet ad Do not disassemble Ground to prevent an electric Do not touch hock O A When not used for extended period of time set your computer to DPM If using a screen saver set it to active screen mode The images here are for reference only and are not applicable in all cases or countries Shortcut to Anti Afterimage Instructions 3 Do not use a damaged power cord or plug or a damaged or loose power outlet e Otherwise this may result in electric shock or fire L Do not touch the power plug with wet hands when removing or plugging the plug into the outlet e Otherwise this may result in electric shock L Make sure to connect the power cord to a grounded power out let e Otherwise it may result in electric shock or personal injury Installation Safety Instructions
11. This marking on the product accessories or literature indicates that the mma product and its electronic accessories e g charger headset USB cable should not be disposed of with other household waste at the end of their working life To prevent possible harm to the environment or human health from uncontrolled waste disposal please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources Household users should contact either the retailer where they purchased this product or their local government office for details of where and how they can take these items for environmentally safe recycling Business users should contact their supplier and check the terms and conditions of the purchase contract This product and its electronic ac cessories should not be mixed with other commercial wastes for disposal Correct disposal of batteries in this product Europe only Applicable in the European Union and other European countries with separate battery return systems This marking on the battery manual or packaging indicates that the bat teries in this product should not be disposed of with other household waste at the end of their working life Where marked the chemical sym bols Hg Cd or Pb indicate that the battery contains mercury cadmium or lead above the reference levels in EC Directive 2006 66 If batteries are not properly disposed of these substances
12. 3 4 or 5 For the Bar and Eraser types it can be set to 10 20 30 40 or 50 For the All White and Pattern type it can be set to 1 5 10 20 or 30 k The Input source of Magici nfo works only on Magicl nfo model The Input source of TV works only on TV model amp The Maintenance Control feature is available only for the displays whose power status is ON i Maintenance Se Ww Video Wall 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen NG Multiple Display Control x File Remote Control Safety Lock Port Selection Lamp Control Options Help kanatanag mo Select Clear Refresh System n Input Source Image Size Video Wall A 1 Video Wall A Video Wall is a set of video screens that are connected together so that each screen shows a part of the whole picture or so that the same picture is repeated on each screen 2 Video Wall Control Video Wall properties can be configured a MDC Video Wall J Video Wall Close Format Natural ee Harizantal Vertical 1 On Off Turns on off the Video Wall function of the selected display 2 Format The format can be selected to see a divided screen e Natural 3 Video Wall Screen divider The screen can be divided into You can select a number of screens with a different layout when dividing Select a mode from Screen divider Select a display from
13. 6 Repeat Available selections include Once EveryDay Mon Fri Mon Sat Sat Sun and Manual Once The Timer goes off only once EveryDay EveryDay The Timer repeats daily Mon Fri The Timer repeats from Monday through Friday Mon Sat The Timer repeats from Monday through Saturday Sat Sun Sat Sun The Timer goes off on Saturday and Sunday Manual Select a day of the week you want the Timer to go off 2 Setting Holiday Management The Holiday Management function specifies the dates in which the monitor will not be turned on or off by the Timer Holiday Management gt Month Day 1 Specifies the date 2 Delete All Deletes all of the holidays 3 Add Adds the specified date 4 mi Deletes the schedule in the selected line The Holiday Management function can be turned on or off in the Timer setup menu The Input source of Magicl nfo works only on Magicl nfo model The Input source of TV works only on TV model amp Time Control is available only for the displays for which the power status is ON k Only enabled for a TV when Source is set to TV in On Time mode Kk Only enabled for a model with Magicl nfo installed when Source is set to Magicl nfo in On Time mode NG PIP D PIP Size 1 Click PIP of the main icons and the PIP control screen appears Selects displays you want to adjust using the Select All button or checkboxes Multiple Display Control File AddaDewce Re
14. If you select lt Yes gt the upgrade is performed When the software upgrade is completed the product is turned off and on automatically Adjusting the LCD Display Fan amp Temperature Auto Power Off Upgrade is completed Power will be off and turned on automatically OK OSD Display Note Setup Reset is This only operates with a digital signal such as in DVI HDMI1 or HDMI2 mode The input resolution must be identical to the panel resolution In HDMI1 and HDMI2 modes the timing values used for both the PC and TV are only supported if the Edit Name is set to PC or DVI PC This is only supported if the Size is set to 16 9 HMT Reset Settings in Setup Yes No Reset all the values for a setting Reset Alle f 175 All Settings return to default settings Yes No Reset all the settings for the display Multi Control Available Modes J PC DVI DisplayPort EV AV 4 Component HDMI M Magicinfo itv Pari Note To watch TV on the product connect a TV tuner box sold separately Note Using Magiclnfo Adjusting the LCD Display To use Magjiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the already included network box to HDMI IN 2 MAGICINFO on the product To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and connect the Magjiclnfo output on the network box to HDMI IN 2 MAG ICINFO
15. When OSD is not on the screen press the button to adjust volume ENTER button ENTER Activates a highlighted menu item SOURCE button SOURCE Switches from PC mode to Video mode Selects the input source that an external device is connected to PC gt DVI gt AV gt Component gt HDMI1 gt HDMI2 gt Dis playPort gt Magiclnfo TV Note e The RGB COMPONENT IN port is compatible with RGB PC and Component signals However the picture may display abnormally if the connected external input signal is different from the selected video signal e A TV tuner box sold separately must be connected to use the TV Note Using Magiclnfo e To use Magiclnfo with an MXN 3 MPN 3 model connect the MagicInfo output on the already included network box to HDMI IN 2 MAGICINFO on the product e To use Magiclnfo with an MX 3 MP 3 model install inside the product a net work box specified by Samsung and connect the Magiclnfo output on the network box to HDMI IN 2 MAGICINFO on the product D MENU button Opens the on screen D MENU Note The D MENU button is activated when a TV tuner is connected and oth erwise the PIP button is enabled PIP button Push the PIP button to turn the PIP screen On Off Power button O Use this button for turning the LCD Display on and off Rear Introduction Power indicator Shows PowerSaver mode by blinking green NA Note See PowerSaver
16. a More Power On Adjustment Advanced Settings Setup Reset Reset All OSD Rotate 1 Landscape 2 Portrait Advanced Settings LANA Mh Configures the settings more elaborately Fan amp Temperature Only Network model Protects the product by detecting the fan speed and internal temperature Adjusting the LCD Display Fan Controls Fan Speed Setting Temperature Control Selects auto or manual for the fan speed settings e Auto e Manual Fan Speed Setting Fan Control Manual 17 et x Temperature Control 7 Sets the fan speed within a range of 0 and 100 Note Enabled when Fan Control is set to Manual Temperature Control Fan Control Manual Fan Speed Setting 17 Detects the product s internal temperature and specifies the desired temperature The product is set to 77 C by default Note e The picture will be dimmed if the temperature exceeds the specified temperature and the product will automatically power off to prevent overheating if the temperature keeps rising e tis best to use the product at temperatures 75 80 C based on ambient temperature of 40 C Refer to Specifications herein for details about operating conditions Note Adjusting the LCD Display e Itis best to set Fan Control to Auto when you change the Temperature Control setting Current Temperature Fan Control Manual Fan Speed Setting ja IF T ri Temperature Control Cur
17. on the product Multi Control k 1551 Assigns an individual ID to the SET Magicinfo ID Setup ID Input MDC Connection R45 MDC b Network Setting La ID Setup Assigns distinctive IDs to the SET ID Input Use to select the transmitter functions of the individual SET Only a SET where the ID corresponds to the transmitter setting becomes activated MDC Connection Selects a port to receive the MDC inputs from e RS232C MDC Communicates with the MDC via a RS232C MDC cable e RJ45 MDC Communicates with the MDC via an RJ45 MDC cable Network Setting e IP Setting Manual Auto e IP Address Manually enter the IP Address if IP Setting is set to Manual e Subnet Mask Manually enter the Subnet Mask if IP Setting is set to Manual e Gateway Manually enter the Gateway if IP Setting is set to Manual Available Modes J PC DVI DisplayPort EV AV Component CJ HDMI Adjusting the LCD Display Magiclinfo hi Tv Note To watch TV on the product connect a TV tuner box sold separately Note Using Magiclnfo To use Magiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the already included network box to HDMI IN 2 MAGICINFO on the product To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and connect the Magjiclnfo output on the network box to HDMI IN 2 MAG ICINFO on the product Note The remote control can b
18. 1 Off 2 On Note Digital NR function is not available for all resolutions HDMI Black Levell Custom Custom Color Tone Normal Sire Digital NR More When a DVD or set top box is connected to your TV via HDMI it may cause a degradation in the screen quality such as an increase in the black level a low contrast or discoloration etc depending on the external device connected In this case adjust the screen quality of your TV by configuring the HDMI Black Level 1 Normal Adjusting the LCD Display 2 Low Note For Timing which can be used for both the PC and the DTV in HDMI mode HDMI Black Level will be activated Film Mode i On Dynamic Contrast Off Lamp Control 100 Picture Reset Film Mode calibrates unnatural picture when watching a movie 24 frames played ona TV 30 frames Moving subtitles may appear corrupted when this mode is enabled In HDMI mode this function is available when the input signal is interlaced scan it is not available in progressive scan 1 Off 2 On PIP Picture ful Adjusts the PIP Screen Settings Note Available Modes PIP On 1 Contrast Adjusts the Contrast of the PIP window on the screen 2 Brightness aa Adjusts the Brightness of the PIP window on the screen 3 Sharpness es Adjusts the Sharpness of the PIP window on the screen Adjusting the LCD Display Dynamic Contrast el Mic i i
19. Actions Note A LCD Display recreates visual signals received from the computer Therefore if there is a problem with the computer or the video card this can cause the LCD Display to become blank have poor Coloring become noisy etc In this case first check the source of the prob lem and then contact a Service Center or your dealer 1 Check if the power cord and the video cables are properly connected to the computer 2 Check if the computer beeps more than 3 times when booting If it does request service 3 Ifyou installed a new video card or if you assembled the PC check if you installed the Adaptor video 4 Check if the scanning ratio of the video screen is set to between 50 Hz 85 Hz Do not exceed 60Hz when using the maximum resolution 5 If you have problems in installing the Adaptor video driver boot the computer in Safe Mode remove the Display Adaptor in the Control Panel gt System gt Device Admin istrator and then reboot the computer to reinstall the Adaptor video driver Check List Note e The following table lists possible problems and their solutions Before calling for assis tance check the information in this section to see if you can remedy any problems for yourself If you do need assistance please call the phone number on the Information section or contact your dealer e For more network related information refer to the Magiclnfo Troubleshooting section Problems related to t
20. Color aaa Na Adjusts the Color of the PIP window on the screen Note Only enabled when the PIP input source is HDMI 5 Tint ea Adds a natural tone to the PIP window ran Note The Tint slider is only displayed when PIP input source is HDMI or AV Dynamic Contrast a More Signal Balance Cit ole Lamp Control Picture Reset Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast 1 Off 2 On Note This function is disabled when PIP or Energy Saving is On Lamp Control aa i Adjusts the inverter lamp in order to reduce energy consumption rs Note Not available when Dynamic Contrast is set to On Adjusting the LCD Display Picture Resets Reset Picture settings Yes Ma Reset the screen settings Picture AV HDMI TV Component Mode Available Modes J PC DVI DisplayPort gt Elav H Component gt HDMI M Magicinfo gt TV Note To watch TV on the product connect a TV tuner box sold separately Note Using Magiclnfo e To use Magiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the already included network box to HDMI IN 2 MAGICINFO on the product e To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and connect the Magjiclnfo output on the network box to HDMI IN 2 MAG ICINFO on the produc
21. Display Selection The place will be set up by pressing a number in the selected mode The maximum number of monitors that can be arranged Horizontal X Vertical 100 Up to 15 monitors can be arranged in a row The maximum value for Horizontal is 6 if Vertical is set to 15 while the maximum value for Vertical is 6 if Horizontal is set to 15 4 Viewing Screen Splits You can view and change the layout of screens using the Screen Divider settings amp The range of the Screen Divider setting may differ depending on the model amp You may not operate this function in Magicl nfo The Input source of TV works only on TV model The Maintenance Control function is available only for the displays where the power status is ON Troubleshooting 1 The display you wish to control does not appear on the System Info Grid Check the connection of RS232C Check if it is properly connected to the Com1 port Check the displays to see if any of the other displays connected have the same ID If more than one displays have the same ID those displays are not properly detected by the program due to data conflict For monitors that support a Set ID between 0 to 99 you have to set the Set ID to a value between 0 and 99 Note Check if the Set ID of the monitor is a value between 0 and 99 set the value using the Display menu 2 The display you wish to control does not appear on the other Control Info Grids Check to see if the display power is O
22. If thunder or lightning is occurring do not touch the power cord a gt or antenna cable e Otherwise this may result in electric shock or fire LJ Do not try to move the monitor by pulling only the wire or the signal cable e Otherwise it may fall and result in electric shock damage to the product or fire due to damage to the cable L Do not lift or move the product back and forwards or right and left while only holding the power cord or signal cables e Otherwise it may fall and result in electric shock damage to the product or fire due to damage to the cable Make sure that the ventilating opening is not blocked by a table or curtain e Otherwise it may result in fire due to an increase in the internal temperature Do not place any containers containing water vases flower pots medicines as well as any metal on the product Ifwaterora foreign material enters the product disconnect the power cord and contact a Service Center e This may result in a product malfunction electric shock or fire 3 Do not use or keep combustible spray or flammable material near the product e Otherwise this may result in an explosion or fire 3 Do not insert any metal such as chopsticks coins pins and steel or flammable objects such as matches or paper inside the J product through the ventilating openings input and output termi e nals etc e If water or foreign material en
23. Pycckwlt Energy Saving Video Wall Safety Screen Portugues More You can choose one of 13 languages English Deutsch Espa ol Frangais Italiano Svenska PYCCKHM Portugu s T rk e FX Seti BAK 8201 Note The language chosen affects only the language of the OSD It has no effect on any software running on the computer Timeb 1 ua Selects from one of 4 time settings Clock Set Sleep Timer Timer and Holiday Manage ment Clock Set Month Day Year Hour Minute am pm Adjusting the LCD Display Current Time Setting Sleep Timer Clock Set Turns the LCD Display off automatically at certain times 1 Off 2 30 3 60 4 90 120 6 150 7 180 Timer1 Timer2 Timer3 On Time 59 Off Time Volume Source You can set the LCD display to automatically turn on or off at a specified time Note e Only enabled when the clock is set using the Clock Set menu e The Manual option allows you to select a day of the week e Holiday When choose Apply timer is not available on holiday when choose Don t apply timer is available on holiday Holiday Management e Add Adjusting the LCD Display You can register holidays e Delete Selected Delete the selected holidays Yes NG You can delete selected holidays Note e Only enabled when registered holidays are selected e More than one holiday can be selected and deleted e Delete All Delete all holi
24. Select All Clear All Refresh lala PIP Size PIP Source PIP Source 1 All Input atl Fi iT Video B l 2 3 O Componer 9 HDMI 10 HOMI op 1 en 4 Pil Fi ta Ye Info Grid shows some basic information necessary to PIP Source Control 1 PIP Source PIP Source can be controlled with turning on the LCD Display power 2 PC Changes the source of the PIP of the selected display to PC 3 BNC Changes the source of the PIP of the selected display to BNC 4 DVI Changes the source of the PIP of the selected display to DVI 5 TV Changes the source of the PIP of the selected display to TV 6 DTV Changes the source of the PIP of the selected display to DTV 7 AV Changes the source of the PIP of the selected display to AV 8 S Video Changes the source of the PIP of the selected display to S Video 9 Component Changes the source of the PIP of the selected display to Component 10 HDMI1 HDMI2 Changes the source of the PIP of the selected display to HDMI 11 DP Switches the PIP Source of the selected Display to DP k Some of the PIP Sources may not be available for selection depending on the input source type of the Main Screen amp The PIP Control feature is available only for the displays whose power status is ON and the PI P function is set to ON HDMI2 may not be supported depending on the product amp DP may not be supported depending on
25. Zoom 7 4 3 Screen Fit Wide Fit Custom ee 3 Wide Zoom 4 1 9 foom Je Info Grid shows some basic information necessary to Image Size Control 1 To adjust Image Size in TV AV S Video Component HDMI1 HDMI2 or DTV mode click the Video Source tab Select the display you want to adjust by using the Select All button or by checking the checkbox 2 Info Grid displays only the display having TV AV S Video Component HDMI1 HDMI2 or DTV as input source 3 Switch Image Size of the selected display randomly 4 The screen modes can only be adjusted when a TV PAL only is connected and the Image Size item is set to Auto Wide 3k Custom may not be supported depending on the product amp Auto Wide Zoom1 and Zoom are not available for selection when the input signal type for Component and DVI HDCP is 720p or 1080i The Auto Wide mode is available only for TV AV and S Video k The Input source of Magicl nfo works only on Magicl nfo model amp The Input source of TV works only on TV model amp The I mage Size Control feature is available only for the displays whose power status is ON amp HDMI2 may not be supported depending on the product Time 1 Click Time of the main icons and the Time Control screen appears Multiple splay Control Fie AddaDewce Remote Control SatetyLock Feul Dewice Alert Lamp Control Help Faulty Device 0 Select AN Clear All Refresh Idle Ml ip addres
26. a od rodal of ue handsain demon ara ey cle iced IN pe have a dak that ontana the daja yau mara bo mibali chek Hawa Dok Hodi Samsung sasa Copy manufacturer s fies frome AA ee e aima vire diea prin ii moan 8 Ifyou can see the following message window then click the Continue Anyway button Then click OK button Hardware Installation The sofware pou ane installing for this hencevere Samsung sawa has ret passed Windows Logo beeing to wendy ws ompake writ einh KP The ma vaky the belir is iita Contivuing yow installation of this software may impair mhon o destabilize the comect contact th hardware vendo for aofheware that has passed Windows Logo testing Note This monitor driver is certified by Microsoft and this installation will not damage your system The certified driver will be posted on Samsung Monitor homepage http www samsung com 9 Click the Close button then click the OK button continually Using the Software Hardware Update Wizard ff Completing the Hardware Update Wirand The vazad kart irha mabaling the sofiera bat Samsung kaa Drem Dalsi Ta vira datali abu Hho dre files Ugdma Dirar To iiaia thee rea fo thee cee ee taka if the dosa kada alter upang iho cree roll LI L Bo Back Drin back bo iha parvicus iniballsd civa ba LU rer ate Tauminaal the dna bihari 10 Monitor driver installation is completed Microsoft Windows 200
27. described in the manual for further information regarding power saving functions For energy conservation turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods Remote Control Sensor Aim the remote control towards this spot on the LCD Display Note See the Connections section for details about cable connections The LCD Display s con figuration at the back may vary slightly depending on the model POWER S W ON 1 OFF Switches the LCD Display On Off 2 POWER The power cord plugs into the LCD Display and the wall outlet Introduction RGB COMPONENT IN PC COMPO NENT Connection Terminal Input e Connect the RGB COMPONENT IN port on the monitor to the RGB port on the PC using the D SUB cable e Connect the RGB COMPONENT IN port on the monitor to the COMPONENT port on the external device using the RGB to COMPONENT cable e Connect the RGB COMPONENT IN port on the monitor to the BNC port on the PC using the RGB to BNC cable DVI IN PC Video Connection Terminal Connect the DVI IN port on the monitor to the DVI port on the PC using the DVI cable 5 RGB DVI DP HDMI AUDIO IN PC DVI DP HDMI Audio Connection Terminal In put Connect the RGB DVI DP HDMI AUDIO IN terminal of the monitor and the speaker output terminal of your computer s sound card using a stereo cable sold separately DPN Receives a signal from the Display po
28. fire 3 When cleaning the product disconnect the power cord and clean it with a soft dry cloth e Do not use chemicals such as wax benzene alcohol thinner mosquito repellant lubricant or cleaner These may change the appearance of the product surface and peel off the indica tion labels on the product 3 Since the product housing is easily scratched make sure to use the specified cloth only 3 When cleaning the product do not spray water directly onto the main body of the product e Ensure that water does not enter the product and that it is not wet e Otherwise this may result in electric shock fire or a malfunc tion L The product is a high voltage product Do not disassemble re pair or modify the product yourself e Otherwise this may result in electric shock or fire If the product needs to be repaired contact a Service Center J If there is a strange smell or a strange sound or smoke is coming from the product disconnect the power plug immediately and con tact a Service Center e Otherwise this may result in electric shock or fire Safety Instructions 3 Do not place this product in a location exposed to moisture dust smoke water or in a car e Otherwise this may result in electric shock or fire L When you drop the product or the case is broken turn the power off and disconnect the power cord Contact a Service Center e Otherwise this may result in electric shock or fire 3
29. in On Time mode Only enabled for a model with Magicl nfo installed when Source is set to Magicl nfo in On Time mode 6 PIP PIP Size 1 Click PIP of the main icons and the PIP control screen appears Selects displays you want to adjust using the Select button or checkboxes Multiple Display Control File Remote Control SafetyLock Port Selection Lamp Control Options Help rT o T PIP Source OL Less asco PARAAN DD nabi All Inputs Ye Info Grid shows some basic information necessary to PIP Size Control 1 PIP Size Shows the current PIP Size of the display in use 2 OFF Turns off the PIP of the selected display 3 Large Turns on the PIP of the selected display and changes the size to Large 4 Small Turns on the PIP of the selected display and changes the size to Small 5 Double 1 Turns on the PIP of the selected display and changes the size to Double 1 6 Double 2 Turns on the PIP of the selected display and changes the size to Double 2 7 Double 3 Picture By Picture Turns on the PBP of the selected display and changes the size to Double 3 k The Input source of Magici nfo works only on Magicl nfo model The Input source of TV works only on TV model PIP Size can be controlled with turning on the LCD Display power NG PIP PI P Source 1 Click PIP of the main icons and the PIP control screen appears m k k Multiple Display Control File Remote Control
30. on Magicl nfo model amp The Input source of TV works only on TV model amp Image Size Control is available only for the displays for which power status is ON 5D I mage Size TV AV S Video Component DVI HDCP HDMI 1 HDMI 2 DTV 1 Click Image Size of the main icons and the Image Size control screen appears Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Help SAMSUNG OIGITall Clear Refresh Video Source 1 TY AV S Video Component HDMI1 HOMI DTW Image Size Auto Wide 16 9 Wide Zoom Zoom Zoom 1 Zoom 7 Screen Fit Custom Ye Info Grid shows some basic information necessary to Image Size Control 1 To adjust Image Size in TV AV S Video Component HDMI1 HDMI2 or DTV mode click the Video Source tab Select the display you want to adjust by using the Select button or by checking the checkbox 2 Info Grid displays only the display having TV AV S Video Component HDMI1 HDM12 or DTV as input source 3 Switch Image Size of the selected display randomly 4 The screen modes can only be adjusted when a TV PAL only is connected and the Image Size item is set to Auto Wide HDMI2 may not be supported depending on the product Custom may not be supported depending on the product k Auto Wide Zoom1 and Zoom are not available for selection when the input signal type for Component and DVI HDCP is 720p or 1080i The Auto Wide mode i
31. sold separately uf Note Using Magiclnfo e To use Magiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the already included network box to HDMI IN 2 MAGICINFO on the product e To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and connect the Magjiclnfo output on the network box to HDMI IN 2 MAG ICINFO on the product Adjusting the LCD Display Model Information Custom Advertisement Color Tone A Color Temp Image Lock Auto Adjustment More g Note Not available when Dynamic Contrast is set to On 1 Information Recommended for communicating exact information e g public information 2 Advertisement Recommended for displaying advertisements e g videos or indoor or outdoor ads 3 Custom Custom LI By using the on screen menus the contrast and brightness can be changed to your personal preference Note By adjusting the picture using the Custom function Mode will change to Custom mode Not available when Dynamic Contrast is set to On 1 Contrast Adjusts the Contrast 2 Brightness Adjusts the Brightness 3 Sharpness Adjusts the Sharpness 4 Gamma Adjusting the LCD Display Contrast Brightness Sharpness maa MMe aime Oa ae Adjust the mid range brightness Gamma for the picture e Natural e Mode 1 Sets the picture brighter than Natural e Mode 2 Sets the picture darker than Mod
32. the screen In TV mode these buttons can be used to configure a list of channels You can select the PC DVI HDMI or DP DisplayPort ex ternal input directly in a mode other than TV mode TV channels provide written information services via tele text Teletext Buttons OE note This function does not work for this LCD Display MTS You can select MTS Multichannel Television Stereo mode Audio Type 98 MTS S Mode Default FM Stereo Mono Mono Manual Stereo Mono Stereo Change SAP Mono e SAP Mono DUAL STEREO MONO DUAL DUAL Il and MONO NICAM MONO NICAM STEREO can be operated depending on the OES OE OSA OEI OEI CONUS OF OES OE D EQ ENTER PRE CH O UK MUTE w CHIP A Ow B MENU QD RETURN ff exit 21 Magiclnfo User Installation Guide note Introduction broadcasting type by using the DUAL button on the remote control while watching TV note Enabled when a TV tuner box is connected This button is used to return to the immediately previous channel Note Enabled when a TV tuner box is connected Pauses mutes the audio output temporarily This is dis played on the lower left corner of the screen The audio comes back on if MUTE or VOL is pressed in the Mute mode In TV mode selects TV channels note Enabled when a TV tuner box is connected Allows you to watch an analogue or digital TV Note Enabled when a TV tuner box is c
33. the set period of time specify a time for execution Bar This function prevents after images on the screen by moving long black and white vertical lines Eraser This function prevents after images on the screen by moving a rectangular pattern Adjusting the LCD Display Pixel This function prevents after images by moving many pixels on the screen Side Gray Pixel Shift limer Select the brightness of the grey for the screen background e Off Light ex Dark Resolution Select s as ci i if maa More Power On Adjustment 1024 X768 OSD Rotation 1280 X 768 Advanced Settings 1360 X 68 Setup Reset 1366 X 768 Reset All When the picture is not displayed properly on the screen when setting the graphics card resolution of the computer to 1024 x 768 60Hz 1280 x 768 60Hz 1360 x 768 60Hz or 1366 x 768 60Hz by using this function Resolution Select you can have the picture displayed on the screen in the specified resolution Note Available in PC mode only 1 Off 2 1024 X 768 3 1280 X 768 Adjusting the LCD Display 4 1360 X 768 5 1366 X 768 Note Selecting the menu is only allowed when the graphics resolution is set to 1024 x 768 60Hz 1280 x 768 60Hz 1360 x 768 60Hz or 1366 x 768 60Hz Power On Adjustment LAXA Thi Adjusts the Power On time for the screen A Caution Set the Power On time to be longer to avoid overvoltage OSD Rotation 15 ki
34. the wall or the product may not stay in place after installation 3 Tighten the 4 screws in step 2 plastic hanger screw B to the rear holes of the product 4 Remove safety pin 3 and insert the 4 product holders into the corresponding bracket holes 1 Then place the product 2 so that it is firmly fixed to the bracket Make sure to re insert and tighten the safety pin 3 to securely hold the product to the bracket A LCD Display B Wall Bracket C Wall Wall Bracket Angle Adjustment Adjust the bracket angle to 2 before installing it on the wall 2 9 5 0 2o oO 1 Fix the product to the wall bracket 2 Hold the product at the top in the center and pull it forward direction of the arrow to adjust the angle Note Introduction You can adjust the bracket angle between 2 and 15 Make sure to use the top center and not the left or the right side of the product to adjust the angle Remote Control RS232C Cable connections interface pin Bits rate Data Bits Parity Stop Bits Flow control Maximum length e Pin assignment Pin NI D JO B D N RS232C 9 pin TxD No 2 RxD No 3 GND No 5 9600 bps 8 bit None 1 bit None 15 m only shielded type Signal Data Carrier Detect Received Data Transmitted Data Data Terminal Ready Signal Ground Data Set Ready Request to Send Introduction 8 Clear to Send 9 Ring Indicator e RS232C cable Conne
35. use the TV e PC DVI AV HDMI1 HDMI2 DisplayPort e DVI PC e AV PC e HDMI PC e DisplayPort PC Size PIP Source Position Transparency Changes the Size of the PIP window Position Changes the Position of the PIP window Transparency Adjusts the Transparency of PIP windows High Adjusting the LCD Display Medium Low Opaque PC DWI AV Component HDMI1 i DisplayPort Move Emer em Name the input device connected to the input jacks to make your input source selection easier VCR DVD Cable STB HD STB Satellite STB AV Receiver DVD Receiver Game Camcorder DVD Combo DHR PC DVI PC DVI Devices Note The displayed devices differ depending on the external input mode When connecting a PC to the HDMI terminal set Edit Name to PC In other cases set Edit Name to AV However since 640x480 720P 1280x720 and 1080p 1920x1080 are common signals for AV and PC make sure to set the Edit Name in accordance with the input signal When a PC is connected set Edit Name to DVI PC to enjoy the video and audio from the connected PC When an AV device is connected set Edit Name to DVI Device to enjoy the video and audio from the connected AV device Source AutoSwitch Settings LAXA Thi Turning on the display with Source AutoSwitch On and the previous video source selection is not active the display will automatically search the different video i
36. 0 31 500 36 000 40 000 50 000 49 500 Horizontal Vertical Fre Pixel Clock Sync Polarity Frequency quency Hz H V Specifications Display Mode Horizontal Vertical Fre Pixel Clock Sync Polarity Frequency quency Hz MHz H V KHz VESA 848 x 480 31 020 60 000 33 750 VESA 1024 x 768 48 363 60 004 65 000 VESA 1024 x 768 56 476 70 069 75 000 VESA 1024 x 768 60 023 75 029 78 750 VESA 1152 x 864 67 500 75 000 108 000 VESA 1280 x 768 47 776 59 870 79 500 VESA 1280 x 960 60 000 60 000 108 000 VESA 1280 x 1024 63 981 60 020 108 000 VESA 1280 x 1024 79 976 75 025 135 000 VESA 1360 x 768 47 712 60 015 85 500 VESA 1366 x 768 47 712 59 790 85 500 VESA 1600 x 1200 75 000 60 000 162 000 VESA 1920 x 1080 67 500 60 000 148 500 Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle and the inverse number of the Hor izontal Cycle is called the Horizontal Frequency Unit kHz Vertical Frequency Like a fluorescent lamp the screen has to repeat the same image many times per second to display an image to the user The frequency of this repetition is called the Vertical Frequency or Refresh Rate Unit Hz Information For a Better Display Adjust the computer resolution and screen injection rate refresh rate on the computer as described below to enjoy the best picture quali
37. 0 Operating System When you can see Digital Signature Not Found on your monitor follow these steps 1 Choose OK button on the Insert disk window 2 Click the Browse button on the File Needed window 3 Choose A D Driver then click the Open button and then click OK button How to install 1 Click Start Setting Control Panel 2 Double click the Display icon 3 Select the Settings tab and click Advanced Properties button 4 Choose Monitor Case1 If the Properties button is inactive it means your monitor is properly configured Please stop installation Case2 If the Properties button is active click the Properties button then follow the next steps 5 Click Driver and then click on Update Driver then click on the Next button 6 Choose Display a list of the known drivers for this device so that can choose a specific driver then click Next and then click Have disk 7 Click the Browse button then choose A D Driver 8 Click the Open button then click OK button 9 Choose your monitor model and click the Next button Then click Next button 10 Click the Finish button then the Close button Using the Software If you can see the Digital Signature Not Found window then click the Yes button Then click the Finish button and the Close button Microsoft Windows Millennium Operating System 1 Click Start Setting Control Panel
38. 1 D MENU a TOOLS Up Down Left Right buttons 1 INFO The Color button and the PC DVI HDMI DP selection button TTX MIX MTS DUAL 29 ENTER PRE CH KK MUTE w CHIP A TV MENU J RETURN g EXIT Magiclnfo O OOOO 0800 808009 000900 Turns the product On Turns the product Off Used to enter the password during the OSD adjustment or to use Magiclnfo Press to change the channel The button is used to select Digital channels Electronic Program Guide EPG display Note This button can only be used in TV mode while a TV tuner box sold separately is connected Adjusts the audio volume source i O0 D MENU OF Toos Up Down Left Right but tons i INFO D The Color button and the PC DVI HDMI DP selection button O SICA TTXMIX MTS DUAL Introduction Selects a connected external input source or Magiclnfo mode Press the button to change the input signal SOURCE Changing the SOURCE is only allowed for external devices that are connected to the LCD Display at the time DTV menu display Note This button can only be used in TV mode while a TV tuner box sold separately is connected Use to quickly select frequently used functions Note This function does not work for this LCD Display Moves from one menu item to another horizontally vertically or adjusts selected menu values Current picture information is displayed on the upper left corner of
39. 999 BULGARIA 07001 33 11 http www samsung com CROATIA CZECH DENMARK EIRE ESTONIA FINLAND FRANCE GERMANY HUNGARY ITALIA KOSOVO LATVIA LITHUANIA LUXEMBURG MACEDONIA MONTENEGRO NETHERLANDS NORWAY POLAND PORTUGAL RUMANIA SERBIA SLOVAKIA SPAIN SWEDEN SWITZERLAND U K ARMENIA AZERBAIJAN Appendix Europe 062 SAMSUNG 062 726 http www samsung com 7864 800 SAMSUNG http www samsung com 800 726786 Samsung Zrt esk organiza n slo ka Oasis Florenc Sokolovsk 394 17 180 00 Praha 8 70 70 19 70 http www samsung com 0818 717100 http www samsung com 800 7267 http www samsung com 030 6227 515 01 48 63 00 00 01805 SAMSUNG http www samsung com 726 7864 E 0 14 Min 06 80 SAMSUNG 726 7864 http www samsung com 800 SAMSUNG 726 7864 http www samsung com 381 0113216899 http www samsung com http www samsung com 8000 7267 http www samsung com 8 800 7777 http www samsung com 261 03 710 http www samsung com 023 207 777 020 405 888 0900 SAMSUNG 0900 7267864 0 10 Min 815 56 480 http www samsung com 0 801 1SAMSUNG 172678 http www samsung com http www samsung com 022 607 93 33 80820 7267864 1 08010 SAMSUNG 72678 doar din reteaua http www samsung com Romtelecom tarif local 2 021 206 01 10 din orice retea tarif normal SAMSUNG http www samsung com 0700 SAMSUNG 0700 726 http www samsung
40. C Out A Multiple Display Control MDC is an application allowing various displays to be easily and simultaneously operated on a PC RS 232C a standard of serial communication is used for the communication between a PC and a display Therefore a serial cable should be connected between the serial port on a PC and the serial port on a display Main Screen Click Start gt Program gt Samsung gt MDC System to start the program Select a set to see the volume of the selected set within the slider a SY eh e Bo 10 11 12 13 14 O Options Help an T Refresh Power On Power Of O30 Display Source OSD Not Optimum Mode OSD No Signal OSD MDC OSD O Main Icons C3 All 2 Remote control Selection Buttons E3 Safety Lock 10 Refresh O Port Selection D Display Selection O Lamp Control B Info Grid GO Option 13 Control Tools amp Dropdown Selectors 14 OSD Display Use the main icons to switch into each screen Allows you to enable or disable the remote control signal receiving function of the display unit Set the Safety Lock function When setting the Lock function you can only operate power and lock buttons on the remote control and set The setting for the PC Serial Port can change The original value is COM1 Selects a Lamp adjustment mode Adjusts the number of LFD IDs and the frequency of search repeats Defines the range of LFD IDs to display You can select or deselect
41. Display using a serial cable is not selected communication will be unavailable 4 The selected port is stored in the program and used for the next program as well System 1 Click System in the main menu to open the system adjustment screen F GB Multiple Display Control Ea File Remote Control Safety Lock Port Selection Lamp Control Options Help SAMSUNG NGITall Refresh Power On Power Off Input Source il Pa a o FO Volume 10 image Size mm OSD Display Source O5D Hot Optimum Mode OSD No Signal OSD MDC OSD a Maintenance Ye Info Grid shows some basic information necessary to System 1 W Power Status 2 Input 3 Image Size 4 On Timer 5 Off Timer 2 Selects displays you want to adjust using the Select button or checkboxes S Multiple Display Control File Remote Control Safety Lock Port Selection LampControl Options Help Refresh a Power On Power Off 1 2 Wolume 0 Zo 110 FA Lamp Temp bus BR Senser Fan Current OSD Display jo o O Source OSD Not Optimum Mode OSD No Signal OSD MDC OSD 3 MW System allows controlling some of the functions of the selected display 1 Power On Off Turns the power of the selected display On Off 2 Volume Controls the volume level of the selected display It receives the volume value of the selected display from the sets and displays it in the slider If
42. Introduction Note A Samsung Electronics service center can provide details 2 Embedded Mount guide lt Side view gt lt Top views x AAA min 40 mm min 70 mm min 50 mm min 50 mm Ambient temperature Measuring point lt 35 C UW m o O WD gt q e When embedding the product in a wall be sure there is some space behind the product for ventilation as shown above and maintain the ambient temperature at 35 C or lower Note A Samsung Electronics service center can provide details 3 Floor mount guide lt Side view gt t Se p rc lt lt A min 50 mm B Ambient temperature Measuring point lt 20 C e When embedding the product in the floor be sure there is a 50 mm space or more behind the product for ventilation as shown above and maintain the ambient temperature at 20 C or lower Note A Samsung Electronics service center can provide details Introduction Mechanical Layout 320MX 3 320MP 3 Installation VESA Bracket When installing VESA make sure to comply with the international VESA standards Introduction e Purchasing VESA Bracket and Installation Information Please contact your nearest SAMSUNG Distributor to place an order After your order is placed installation profes sionals will visit you and install the bracket e Atleast 2 persons are needed in order to move the LCD Display e SAMSUNG is not responsible for any product damage or any injury caus
43. LAN D sub out HDMI out With Network Dimensions W x H x D With Stand 780 0 mm x 545 0 mm x 311 0 mm 30 7 x 21 5 x 12 2 inches Without Stand 780 0 mm x 482 0 mm x 109 0 mm 30 7 x 19 0 x 4 3 inches Weight With Network 320MXN 3 15 1 Kg 33 3 Ibs 320MPN 3 Without Network 13 7 Kg 30 2 Ibs 320MX 3 320MP 3 Specifications VESA Mounting Interface 200 0 mm x 200 0 mm Environmental considerations Operating With Network Temperature 50 F 104 F 10 C 40 C Box Humidity 10 80 non condensing Operating Without Net Temperature 32 F 104 F 0 C 40 C work Box Humidity 10 80 non condensing Storage Temperature 4 F 113 F 20 C 45 C Humidity 5 95 non condensing Plug and Play Capability This LCD Display can be installed on any Plug amp Play compatible system The interaction of the LCD Display and the computer systems will provide the best op erating conditions and LCD Display settings In most cases the LCD Display installation will proceed automatically unless the user wishes to select alternate settings Dot Acceptable TFT LCD panels manufactured by using advanced semiconductor technology with precision of 1ppm one millionth above are used for this product But the pixels of RED GREEN BLUE and WHITE Color appear to be bright sometimes or some black pixels may be seen This is not from bad quality and you can use it without any problems Fo
44. MI or other external input sources connected to the LCD Display Use to select the screen of your choice 1 2 PC DVI AV Component HDMI1 This is deactivated when a TV tuner box is installed HDMI2 This is deactivated when a network box is installed Adjusting the LCD Display 7 DisplayPort 8 Magiclnfo A network box must be connected to use Magiclnfo with a MX 3 MP 3 model 9 TV Enabled if a TV tuner box is connected Note The RGB COMPONENT IN port is compatible with RGB PC and Component signals However the picture may display abnormally if the connected external input signal is different from the selected video signal PIPL ki PIP Source Note The PIP function is not available when Video Wall is On When external AV devices such as VCRs or DVDs are connected to the LCD Display PIP allows you to watch video from those devices in a small window super imposed on the PC Video signal Off On Note e PIP turns off when the LCD Display is switched to an external source If you select LI I CL l B in Size Position and Transparency will not be activated Turns the PIP Screen Off On e Off e On PIP Size Pasition Transparency Selects the input source for the PIP DVI HOMIL ee DisplayPort Adjusting the LCD Display Note e PIP is disabled if the primary screen does not receive a signal e A TV tuner box sold separately must be connected to
45. N You can check this in System Info Grid Check if you can change the input source of the display 3 The dialogue box appears repeatedly E Check to see if the display you wish to control is selected 5 4 Both On Timer and Off Timer have been set but different time is showing Apply current time to synchronize the display clocks 5 The remote may not function properly when you turn off the remote Function disconnect the RS 232C cable or exit the program in an Irregular manner Rerun the program and turn the remote function again to Restore normal functions lt Note gt This program may malfunction due to problems in communication circuits or interference from electronic appliances nearby Please make selection in the information qrid before controlling Settings Value Display In Multiple Display Mode ve When there are more than one displays connected the settings values are displayed as follows 1 No selection Displays the Factory Default Value 2 Selected one display Fetches and displays the settings value for the selected display 3 Selected one display ID1 and add another display ID3 The program which was displaying the settings value of ID 1 fetches and displays the value of ID3 4 Ifall sets are selected at the same time by clicking All and Select the default value will be restored Copyright 2003 2010 Samsung Electronics Co Ltd All rights reserved Ethernet MDC Multiple Displa
46. Safety Lock Port Selection Lamp Control Options Refresh PIP Source All inputs Info Grid shows some basic information necessary to PIP Source Control PIP Source PIP Source can be controlled with turning on the LCD Display power PC Changes the source of the PIP of the selected display to PC BNC Changes the source of the PIP of the selected display to BNC DVI Changes the source of the PIP of the selected display to DVI TV Changes the source of the PIP of the selected display to TV DTV Changes the source of the PIP of the selected display to DTV AV Changes the source of the PIP of the selected display to AV S Video Changes the source of the PIP of the selected display to S Video Component Changes the source of the PIP of the selected display to Component HDMI 1 HDMI2 Changes the source of the PIP of the selected display to HDMI DP Switches the PIP Source of the selected Display to DP HDMI 2 may not be supported depending on the product DP may not be supported depending on the product Some of the PI P Sources may not be available for selection depending on the input source type of the Main Screen The I nput source of Magicl nfo works only on Magicl nfo model The PIP Control feature is available only for the displays whose power status is ON and the PI P function is set to ON le Settings Picture 1 Click Settings of the main icons and the Settings Control s
47. Turns Off On the Video Wall function of the selected display Off On e Off e On Format Video Wall Horizontal Natural Vertical sal Screen Position The Format can be selected to see a divided screen e Full Provides a full screen without any margins e Natural Displays a natural image with the original aspect ratio intact Horizontal Video Wall Format Vertical Screen Position Adjusting the LCD Display Sets how many parts the screen should be divided horizontally Fifteen adjustment levels 1 15 Pari Note If Vertical is set to 15 the maximum value for Horizontal is 6 Vertical Video Wall Format Horizontal Screen Position Sets how many parts the screen should be divided vertically Fifteen adjustment levels 1 15 Pan Note If Horizontal is set to 15 the maximum value for Vertical is 6 Screen Position The screen can be divided into several images A number of screens can be selected with a different layout when dividing Select a mode in Screen Position e Select a display in Display Selection e The selection will be set up by pressing a number in the selected mode e The screen can be split into a maximum of 100 sub screens Note When more than four displays are connected we recommend a resolution of XGA 1024 768 or greater to prevent any picture degradation Safety Screen LAXA Th The Safety Screen function is used to prevent afterimages that may a
48. UDIO OUTPUT jacks on the camcorder and the AV COMPONENT AUDIO IN R AUDIO L on the LCD Display 3 Press SOURCE on the product or remote control and select AV 4 Then start the Camcorders with a tape inserted Note The audio video cables shown here are usually included with a Camcorder If not check your local electronics store If your camcorder is stereo you need to connect a set of two cables Connections Connecting Using a HDMI Cable ma 1 Connect an HDMI cable to HDMI IN 2 MAGICINFO or HDMI IN 1 on the product and the HDMI output port on a digital device 2 Press SOURCE on the product or remote control and select HDMI1 HDMI2 Note In HDMI mode only PCM format audio is supported Connecting Using a DVI to HDMI Cable Connect a DVI HDMI cable to HDMI IN 2 MAGICINFO or HDMI IN 1 and the DVI output port on the digital device Connect the red and white jacks of an RCA to stereo for PC cable to the same colored audio output terminals of the digital output device and con nect the opposite jack to the RGB DVI DP HDMI AUDIO IN terminal of the LCD Display Connections 3 Press SOURCE on the product or remote control and select HDMI1 HDMI2 Connecting a DVD Player Pa Pa T L R 5 WIDEO COMPONENT AUDO OUT Connect a RGB to Component cable between the RGB COMPONENT IN port on the LCD Display and the Pp Y Pp jacks on the DVD player Connect a
49. You can connect USB devices such as a mouse or keyboard Note Applicable to the MXn 3 MPn 3 model only Using the Software Monitor Driver Note When prompted by the operating system for the monitor driver insert the CD ROM included with this monitor Driver installation is slightly different from one operating system to another Follow the directions appropriate for the oper ating system you have Prepare a blank disk and download the driver Program file at the Internet web site shown here Internet web site http www samsung com Installing the Monitor Driver Automatic 1 Insert CD into the CD ROM drive 2 Click Windows 3 Choose your monitor model in the model list then click the OK button a SAMSUNG monitor installer Saal the moadorahich you wari bo nabali 4 Ifyou can see following message window then click the Continue Anyway button Then click OK button Microsoft Windows XP 2000 Operating System Hardware Installation A The sofware pou are installing for this hardware Samsung sasa has no passed Windows Logo besing bo ani its compatibel with Windows XP Tell mg why the besting ts important Continuing your installation of this software may impair or destabilize the comect operation of your system either immediately of in the future Microzoll strongly recommends thal pou stop this installation now and contact the hardware vendor for software that has passed Window Logo b
50. a adio daneg hardware Note This monitor driver is under certifying MS logo and this installation will not damage your system The certified driver will be posted on Samsung Monitor homepage Click Update Driver in the Driver tab Se ADA Gets BAN LE beret Camo mira aiai Peedi pote AA paie ee PEPP DE te To aa iha Greer piee Agr ha daga She daa Pa afer updates thee dir ral back NG ai imran related Per Chapin Ta pabata danica Tiuri Ba door Ara Check the Browse my computer for driver software checkbox and click Let me pick from a list of device drivers on my computer CR M Hoey do ATAT gaith bo a Groene kor dreser poitean on pour Gomes Terst m deen eo n Ba m Farn Charth dutenai fee opiata drier sahai p Airgas md pee bye eee al Se dreri Me Der Ard hun ee ar ive F roande nobena E E Stal et ee Paan j peck bom a lint of Grice driven on My computer Tina lel ar heen rede Bee Phe pede ee Po dee r aral all dover naga m ibr ar irgo m r iraa Click Have Disk and select the folder for example D Drive where the driver setup file is located and click OK Using the Software i mga Ghat kha conta dhre a mieded baliw Sarte the aman net pou anal in maba fer thig hardware ora CT Cancel Tani Pa siropi jl Sja a peer Paanan thee o Por plain Pee Pa bara il Pal a Pa eae pin bid Pal th Bos kah Haz Yare Pl ria 9 Select the model that matches y
51. a type of system setting file 1 Press Enter at the first and the second screen after executing the X86Config file 2 The third screen is for setting your mouse 3 Seta mouse for your computer 4 The next screen is for selecting a keyboard Using the Software 5 Set a Keyboard for your computer 6 The next screen is for setting your monitor 7 First of all set a horizontal frequency for your monitor You can enter the frequency directly 8 Seta vertical frequency for your monitor You can enter the frequency directly 9 Enter the model name of your monitor This information will not affect the actual execution of X Window 10 You have finished setting up your monitor Execute X Window after setting other re quested hardware MDC Multiple Display Control L33 MDC Installation 1 Insert the installation CD into the CD ROM drive 2 Click the MDC System installation Program Note If the screen for installing the software does not appear install it using the MDC System execution file in the MDC folder of the CD ROM 3 Ifthe installation wizard screen does appear click Next 4 The License Agreement screen will appear Click Yes 5 The Customer Information window will appear Register the user information and click Yes 6 The Choose Destination Location window will appear Specify the file location to install to and click Next Note If the file location is not specified the P
52. amp Schedule Lamp Schedule On Hour Minute am pm Lamp Schedule 1 100 Adjusts the luminance to a user specified value at a specified time OSD Display Displays or hides a menu item on the screen Source OSD Not Optimum Mode OSD No Signal OSD MDC OSD Off e On Not Optimum Mode OSD Source OSD No Signal OSD MDC OSD e Off e On No Signal OSD Source OSD OFF Not Optimum Mode OSD Off MDC OSD a MDC OSD Adjusting the LCD Display Off On Source OSD Not Optimum Mode OSD Off No Signal OSD Off On Software Upgrade Performs a software upgrade 1 Connect the product to a computer via a digital signal such as DVI or HDMI Click the BMP image file converted from an SW code The image below will appear on the screen of the product While a BMP image onto which the software code has been converted is displayed on the screen select Software Upgrade Note When there are two or more BMP images they are displayed on the screen using a slideshow e It is recommended that the playback interval between two BMP images in the slide show should be one second The image extraction probability will decrease with other playback intervals e A BMP image might not be extracted if it is covered by another image for example the mouse pointer If a more recent version than the current software version is detected you will be asked whether to upgrade the current software
53. ary or secondary display in PIP mode Note Available when PIP is set to On 1 Main 2 Sub Speaker Select L215 Las Mode Custom Custom Auto Volume SRS TS AT Sound Reset Off Off When you use the product with it connecting to a Home Theater turn the internal speakers off so you can listen to sound from the Home Theater s external speakers 1 Internal Sound is outputted both from the Internal speaker and the External speakers but the volume control is only available from the Internal speaker 2 External When sound is only outputted from the External speakers the volume control is also only available from the External speakers Sound Reset 2 k4 4 Yes Nea Reset the sound settings Setup Available Modes JPC DVI DisplayPort Adjusting the LCD Display Elav z 7 Component C HDMI j 7 Magicinfo TV a Note To watch TV on the product connect a TV tuner box sold separately Note Using Magiclnfo e To use Magiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the already included network box to HDMI IN 2 MAGICINFO on the product e To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and connect the Magjiclnfo output on the network box to HDMI IN 2 MAG ICINFO on the product Language 15 LBi A Time Deutsch Menu Transparency Espanol Safety Lock Francais taliano Svenska
54. ays a screen resolution of up to 720 480 SD is supported for movies Adjusting the LCD Display e For drive D EWF is not applied e To save Setup contents that have been changed when EWF is in the Enable state you must Commit them e By selecting Disable Enable or Commit the system is restarted Magiclinfo 1 Select Application step 1 iis Magicinfo Setup Wizard v 1 09 Select Application step 1 M Magiclnfo Pro LAN WAN based version E Magiclnfo Advanced Web based version 60 day Trial Edition E Select Later Click Mest M gt Finish Cancel You can select an Application to be executed in your computer when Windows starts 2 Select TCP IP step 2 NG Magicinfo Setup Wizard 1 1 09 Select TCP IP step 2 Obtain an IP address automatically M Use the following IP addres put IP address Subnet mask Default gateway Preferred ONS server Alternate ONS server Click lt Back B Mext N gt Finish Cancel In step 2 of Magiclnfo Setup Wizard you don t have to go to Network Setting on the desktop to make your settings for TCP IP You just do that at step 2 of Magiclnfo installation Adjusting the LCD Display 3 Select Language step 3 TA Magicinfo Setup Wizard 7 1 09 m Select Language step 3 Select the language you want to install on the system for menus and dialogs Current language English CJ Chinese Traditional
55. by public recycling center or to a store selling the same type of the battery or rechargeable battery L Do not place the product in a location exposed to direct sunlight or near any heat such as a fire or heater e This may reduce the lifetime of the product and may result in fire L Do not drop any objects onto the product or cause any impact to the product e Otherwise this may result in electric shock or fire L Do not use a humidifier near the product e Otherwise this may result in electric shock or fire IL When there is a gas leak do not touch the product or the power plug ventilate immediately e Ifa spark occurs it may cause an explosion or fire 3 If the product has been turned on for a long time the display panel becomes hot Do not touch it 3 Keep the small accessories in a location out of the reach of children L Be careful when adjusting the angle of the product or the height of the stand e This may result in personal injury as your hand or fingers may become caught e Also if you tilt the product too far it may fall and cause personal injury Safety Instructions CJ Do not install the product in a location low enough for children to reach e Otherwise it may fall and result in personal injury e Since the front part of the product is heavy install the product on a level and stable surface 3 Do not put any heavy objects on the product e This may result in personal injury and or
56. can cause harm to human health or the environment To protect natural resources and to promote material reuse please sep arate batteries from other types of waste and recycle them through your local free battery return system Note The rechargeable battery incorporated in this product is not user replaceable For information on its replacement please contact your service provider Authority Information in this document is subject to change without notice 2010 Samsung Electronics Co Ltd All rights reserved Reproduction in any manner whatsoever without the written permission of Samsung Elec tronics Co Ltd is strictly forbidden Appendix Samsung Electronics Co Ltd shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing performance or use of this ma terial Samsung is the registered trademark of Samsung Electronics Co Ltd Microsoft Windows and Windows NT are registered trademarks of Microsoft Corporation VESA DPM and DDC are registered trademarks of Video Electronics Standard Association All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners TruSurround XT SRS and the symbol are trademarks of SRS SISO Labs Inc mesurent TruSurround XT technology is incorporated under license from SRS Labs Inc
57. ck com DATA eon no Length PONNE um OxFF a W ont Power Power Same as above e Nak com DATA en mw o Length mera pasan um ERR Error code that shows what occurred error is Volume Control e Function Personal Computer changes volume of TV Monitor e Get Volume Status CheckSum o e Set Volume Header command DATA DATA Length CheckSum Volume Volume value code to be set on TV Monitor O 100 com DATA um Volume Same as above com DATA EJES Length ROKA pabaon um Introduction ERR Error code that shows what occurred error is e Input Source Control e Function Personal Computer changes input source of TV Monitor e Get Input Source Status CheckSum o e Set Input Source Header command DATA DATA Length CheckSum Input Source Input Source code to be set on TV Monitor A Caution DVI VIDEO HDMI1_PC HDMI2_PC Get Only In the case of Magiclnfo only possible with models include Magiclnfo In the case of TV only possible with models include TV e Ack Introduction Header SOU DATA nckiNak r CMD Val mand Length Check Sum Source Input Source Same as above e Nak com DATA ee e Length none Pag um ERR Error code that shows what occurred error is e Screen Mode Control e Function Personal Computer changes Screen Mode of TV Monitor Cannot be controlled when Video Wall is on Caution Only w
58. com 7864 0800 SAMSUNG 726 7864 http www samsung com 902 1 SAMSUNG 902 172 http www samsung com 678 0771 726 7864 SAMSUNG http www samsung com 0848 SAMSUNG 7267864 http www samsung com ch CHF 0 08 min http www samsung com ch fr French 0330 SAMSUNG 7267864 http www samsung com CIS 0 800 05 555 088 55 55 555 BELARUS GEORGIA KAZAKHSTAN KYRGYZSTAN MOLDOVA RUSSIA TADJIKISTAN UKRAINE UZBEKISTAN AUSTRALIA NEW ZEALAND CHINA HONG KONG INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE TAIWAN THAILAND Appendix CIS 810 800 500 55 500 8 800 555 555 8 10 800 500 55 500 GSM http www samsung com 7799 00 800 500 55 500 00 800 500 55 500 8 800 555 55 55 8 10 800 500 55 500 0 800 502 000 8 10 800 500 55 500 Asia Pacific 1300 362 603 http www samsung com http www samsung com http www samsung com http www samsung com ua http www samsung com ua ru http www samsung com http www samsung com 0800 SAMSUNG 0800 726 http www samsung com 786 400 810 5858 010 6475 1880 852 3698 4698 3030 8282 1800 110011 1800 3000 8282 1800 266 8282 0800 112 8888 021 5699 7777 0120 327 527 1800 88 9999 1 800 10 SAMSUNG 726 7864 1 800 3 SAMSUNG 726 7864 1 800 8 SAMSUNG 726 7864 02 5805777 http www samsung com http www samsung com hk http www samsung com hk en http www samsung c
59. creen appears Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Select Cle Refresh Contrast 100 Brightness 15 mg so Sharpness Color Pam Color Tone po Color Temp 10000K rightness Sensor 10 Dynamic Contrast Je Basic information required to adjust the Picture is displayed in the main menu Settings for the selected monitor will be displayed if one of the connected monitors is selected and the default settings will be displayed if all monitors are selected by clicking All and Select If a value is changed in this screen the current mode will automatically switch to custom mode 1 Picture Available only for TV AV S Video Component HDMI1 HDMI2 DTV 2 Contrast Adjusts Contrast of the selected display 3 Brightness Adjusts Brightness of the selected display 4 Sharpness Adjusts Sharpness of the selected display 5 Color Adjusts Color of the selected display 6 Tint Adjusts Tint of the selected display Available only for NT 7 Color Tone Adjusts the Color Tone for the selected display 8 Color Temp Adjusts the Color Temp for the selected display 9 Brightness Sensor Adjusts the Brightness Sensor for the selected display 10 Dynamic Contrast Adjusts the Dynamic Contrast for the selected display HDMI2 may not be supported depending on the product Brightness Sensor may not be supported depending on the product
60. ctor 9 pin D Sub Cable Cross reversed cable P1 P1 P2 P2 FEMALE Rx a gt 3 Rx FEMALE TX 3 lt 2 TX Gnd DO aaa 5 Gnd e Connecting method ee a Da oe ug bag Ba Ba ji i Control codes e Get control CheckSum e Set control Header command DATA DATA Length CheckSum OxAA command 1 Value type e commanding words Introduction 2 Volume contort a nput source conor foa o 4 Seen Made contol fot 7 Auto agustment contr Joso o 8 Video wall Mode comro Jose or a Safety Lock itso ID should show hexadecimal value of assigned ID but ID O should be OxFF Every communication will be made in hexadecimals and Checksum is the sum of all remainings If it exceeds two digits for example it is 11 FF 01 01 112 discard the number in the first digit like below example PowerOn amp ID 0 Header command DATA DATA 1 i Header command DATA DATA 1 Length 12 If you want to control every mechanism connected with Serial Cable regardless of its ID set ID part to OxFE and send commands At the time each product will follow commands but it will not respond with ACK Power Control e Function Personal Computer turns TV Monitor power ON OFF e Get Power ON OFF Status CheckSum o e Set Power ON OFF Header command DATA DATA a CheckSum OxAA 0x11 Power Power Power code to be set on TV Monitor 1 Power ON Introduction 0 Power OFF e A
61. cts whether to display the menu screen using the OSD Display menu F 1 B Muliple Display il miral EA File AddaDewce Remote Control Setety Lock Fault Device Alet Lamp Control Help SAMSUNG DIGITad 1 Faulty Device 0 Select Al Clear All Refresh Idle 1 Ho MM Input Image Size On Time OM Time a oje o rc we Oo ok mua ll v UMEME pata aten H Image Size JB al SET NOTES CANG Un sonar Pan Current Ten Ci 8 SD Display Source OSO On Not Optimum Mode OSD On Signal OSD On DC OSD NG Settings lt Mair iter lance 1 Source OSD Sets whether the Source OSD will be displayed to indicate when the Source is changed 2 Not Optimum Mode OSD Sets whether the Optinum Mode OSD will be displayed to indicate if the current mode is not supported 3 No Signal OSD Sets whether the No Signal OSD will be displayed to indicate when there is no signal 4 MDC OSD Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC Network R L Multiple Display Control w esi File Adda Device Remote Control Safety Lock Fault Device Alert Lemp Control Help _ SAMSUNG DIGITAN li oF aulty Dew VICE al Select All ClearAll Retreach Delete idle System DHE P Enable Disable Subnet ee 205 h5 Galeway 10 08 43 1 Appl
62. cur when a LCD panel is operated under normal con ditions Normal conditions are defined as continuously changing video patterns When the LCD panel is operated for a long time with a fixed pattern over 12 hours there may be slight difference in voltage between electrodes that work the liquid crystal LC in a pixel The voltage difference between electrodes increases with time forcing the liquid crystal to lean When this occurs the previous image may be seen when the pattern is changed To prevent this the accumulated voltage difference must be decreased Information Common Electrode ITO F Color Filter Black Matrix Data Gate Bus Line TFT Pixel Electrode Storage Capacitor ITO Cs ba Power Off Screen Saver or Power Save Mode e Turn the power off for 2 hours after 12 hours in use e Set the Monitor to power off with the PC Display Properties Power Scheme e Use a Screen saver if possible Screen saver in one Color or a moving image is recommended e The Image Retention Free function applied to the product is recommended For detailed configuration procedures refer to the back page E3 Change the Color Information periodically Type 1 FLIGHT FLIGHT O2348 OZ2348 UA102 UA102 Note Use Two different Colors Rotate the Color Information with 2 different Colors every 30 minutes e Avoid using a combination of characters and background Color with large dif ference in luminance Avo
63. damage to the prod uct Introduction Package Contents Note e After unpacking the package make sure to check the contents of the package e Store the packaging box in case you need to move the Product later e f any items are missing contact your dealer e Contact a local dealer to purchase optional items Unpacking LCD Display Manuals Quick Setup Guide Warranty Card User s Guide Not available in all loca tions Cables Power Cord D Sub Cable Others Remote Control Batteries AAA X 2 Introduction Others BP59 00138B Not available in all loca tions Sold separately lai Semi Stand KIT LAN Cable USB Cable Applicable to the MXn 3 MPN 3 model only RGB to BNC Cable RGB to COMPONENT Ca Network Box ble Applicable to the MX 3 MP 3 model only Wall Mount KIT RS232C Cable TV tuner box Your LCD Display The color and the appearance may differ depending on the product and the specifications are subject to change without prior notice to improve the performance Front MENU button MENU Introduction Opens the on screen menu and exits from the menu Also use to exit the OSD menu or return to the previous menu Navigate buttons Up Down buttons Moves from one menu item to another vertically or adjusts selected menu values Adjust buttons Left Right buttons Volume buttons Moves from one menu item to another horizontally or adjusts selected menu values
64. days Yes NG You can delete all the registered holidays Menu Transparency X3 5 i i j Language English Time High Energy Saving Low Video Wall Safety Screen More Change the transparency of the background of the OSD Adjusting the LCD Display 1 High 2 Medium 3 Low 4 Opaque Safety Lock Mk Change PIN The password can be changed The preset password for the LCD Display is 0000 a Note If you forgot your password press the remote buttons INFO EXIT MUTE to reset the password to 0000 Lock Enter PIN a ee This is the function that locks the OSD in order to keep the current settings or to prevent others from adjusting the settings Energy Saving k LEi Sa if Language English Time Menu Transparency Medium Safety Lock Video Wall Safety Screen More This feature adjusts the power consumption of the unit in order to save energy 1 Off 2 On Adjusting the LCD Display Video Wall C3 Th A Video Wall is a set of video screens connected together so that each screen shows a part of the whole picture or where the same picture is repeated on each screen When the Video Wall is on you can adjust the Video Wall screen setting I7 Note e When Video Wall is running the Size functions are not available e Disabled when PIP is set to On Video Wall a 1G EO a a aaa Off Format Horizontal sa Vertical Al
65. e Selects Movie when viewing movies 4 Speech Selects Speech when watching a show that is mostly dialog i e news 5 Custom Selects Custom if you want to adjust the settings according to your personal preferen ces Custom Th The sound settings can be adjusted to suit your personal preferences Note Bass You can hear the sound even when sound value is set to 0 If you adjust sound using Custom function Mode will turn to Custom mode Adjusting the LCD Display Emphasizes low frequency audio Treble Emphasizes high frequency audio Balance a ee Allows you to Adjusts the sound balance between the left and right speakers Auto Volumels 1 1781 Mode Custom Custom SRS TS XT On Speaker Select Internal Sound Reset Reduces the difference in volume control between broadcasters 1 Off 2 On SRS TS XTO AUTO Mode Custom Custom Auto Volume Speaker Select Sound Reset SRS TS XT is a patented SRS technology that solves the problem of playing 5 1 multichannel content over two speakers TruSurround XT delivers a compelling virtual surround sound experience through any two speaker playback system including internal television speakers It is fully compatible with all multichannel formats 1 Off 2 On Adjusting the LCD Display Sound Select Z hil Mode Custom Auto Volume SRS TS XT Speaker Select Sound Reset Enable the sound of either the prim
66. e warmth of the image Colors Note This function is enabled when Mode is set to Custom and Dynamic Contrast and Color Tone are Off SizeLT A oom1 oom2 4 3 Screen Fit Custom The Size can be switched PC mode PC HDMI PC Timing 16 9 4 3 Video mode HDMI Video Timing AV or Component 16 9 Zoom1 Zoom2 4 3 Screen Fit Custom 1 16 9 Sets the picture to 16 9 wide mode 2 Zoom 1 Magnifies the size of the picture on the screen 3 Zoom 2 Magnifies the size of the picture more than Zoom 1 Adjusting the LCD Display 4 4 3 Sets the picture to 4 3 normal mode 5 Screen Fit Displays the input scenes as they are without any cutoff when HDMI 720p 1080i 1080p signals are input 6 Custom Changes the resolution to suit the user s preferences Note e Certain external devices may feed the display an out of spec signal that may cause cutoff even when using the Screen Fit feature e Screen Fit is enabled for only 1080i p in Component mode and for 1080i p or 720p in HDMI mode e Zoom 1 and Zoom 2 are disabled for HD signals 1080i p 720p or 768p e The Position and Reset functions are available in Zoom 1 or Zoom 2 modes Digital NR Digital Noise Reduction LLIS ss Mode Custom Custom Color Tone Normal Size 169 On T More Turns the Digital Noise Reduction feature Off On The Digital Noise Reduction feature allows you to enjoy clearer and crisper images
67. e 1 e Mode 3 Increases the contrast between dark and bright colors Color Tonel Mode Custom Custom Cool Color Temp Normal Image Lock Warm Auto Adjustment Custom 7 hlore ae ee Note Not available when Dynamic Contrast is set to On The Color tones can be changed 1 2 3 4 5 Off Cool Normal Warm Custom Note If you set the Color Tone to Cool Normal Warm or Custom the Color Temp function is disabled If you set the Color Tone to Off the Color Control function is disabled Adjusting the LCD Display Color Control Adjusts individual Red Green Blue Color balance Note Not available when Dynamic Contrast is set to On 1 Red i 2 Green p 3 Blue a Color Temp LIT Color Temp is a measure of the warmth of the image Colors Note This function is enabled when Mode is set to Custom and Dynamic Contrast and Color Tone are Off Image Lock Lid Image Lock is used to fine tune and get the best image by removing noise that creates unstable images with jitters and shakiness If satisfactory results are not obtained using the Fine adjustment use the Coarse adjustment and then use Fine again Note Available in PC mode only Coarse ee ee Removes noise such as vertical stripes Coarse adjustment may move the screen image area You may relocate it to the Center using the horizontal control menu Fine p Remov
68. e afterimages that occur when a still screen is displayed on the selected display for a long time 2 Pixel Shift This allows the screen to be moved finely at the specified time interval 3 Safety Screen The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time The Interval item is used to set the repetition cycle in hour units and the Time item is used to set the time when the Safety Screen function must be performed The Type item can be set to Scroll Pixel Bar Eraser All White or Pattern 4 Safety Screen2 This function is used to prevent afterimages from occurring There are five 5 types that you can select and control with this function For the Scroll type the Time item can be set to 1 2 3 4 or 5 For the Bar and Eraser types it can be set to 10 20 30 40 or 50 For the All White and Pattern type it can be set to 1 5 10 20 or 30 amp The Maintenance Control feature is available only for the displays whose power status is ON amp The Input source of Magicl nfo works only on Magicl nfo model k The Input source of TV works only on TV model Maintenance Ww Video Wall 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen SS Multiple Display Control CS Kal File AddaDewce Remote Control SetetyLock FoultDewce Alert Lamp Control Help rrerapen ook Faulty Device 0
69. e selected display regardless of the time The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control 3 Ambient Light Detects the ambient light intensity at the designated monitor and automatically adjusts the picture brightness You can specify a Reference value and designate a monitor that will automatically determine Lamp Value the light intensity from the lamp based on the ambient light intensity Ambient Light is only supported for models that have a brightness sensor and is only enabled when Ambient Brightness Mode is selected in the Lamp Control menu amp Auto Lamp Control and Manual Lamp Control are only enabled when User Control Mode is selected in the Lamp Control menu amp The Maintenance Control feature is available only for the displays whose power status is ON The Input source of Magicl nfo works only on Magicl nfo model The Input source of TV works only on TV model Maintenance Ww Scroll 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen Multiple Display Control File Add a Device Remote Control SofetyLock Fault Device Alert Lamp Control Help prenne oo Faulty Device 0 Select All Clear All Refresh Idle is Scr Pixel Shift winontal Dots Apply safety Screen or alor le i i C Apply Salety Screen 2 Apply Q 1 Scroll This function is used to remove th
70. e time to scan one line connecting the right edge to the left edge of the screen horizontally is called the Horizontal Cycle The inverse number of the Horizontal Cycle is called Horizontal Frequency Unit KHz Showing the horizontal lines of the screen from the top to the bottom sequentially is called the Non Interlace method while showing odd lines and then even lines in turn is called the Interlace method The Non Interlace method is used for the majority of monitors to ensure a clear image The Inter lace method is the same as that used in TVs This is a function that provides the best quality screen for the user by allowing the computer and the monitor to ex change information automatically This monitor follows the international standard VESA DDC for the Plug amp Play func tion The number of horizontal and vertical dots used to compose the screen image is called the resolution This number shows the accuracy of the display A high resolution is good Appendix for performing multiple tasks as more image information can be shown on the screen Example If the resolution is 1366 x 786 this means the screen is composed of 1366 horizontal dots horizontal res olution and 786 vertical lines vertical resolution Correct Disposal Correct Disposal of This Product Waste Electrical amp Electronic Equipment Europe only Applicable in the European Union and other European countries with separate collection systems
71. e used to select Magiclnfo However it is recommended to use a separate USB keyboard to utilize Magicinfo fully For Magiclnfo in Device mode moving external devices while booting may cause errors Set up external devices only if the LCD Display turns on Do not unplug the LAN cable used for the network ex video display Otherwise the Program Magiclnfo may stop If you do unplug the cable restart the system Do not unplug the LAN cable used by an USB device ex video display Otherwise the Program Magiclnfo may stop To access other sources press the SOURCE button in Magiclinfo The preset password for the LCD Display is 000000 The server Program s Power On option works only if the LCD Display s power is com pletely shut off Please make sure not to use the Power On option when the LCD Display is in the process of shutting down since this may cause system errors on the LCD Display When using Magiclnfo with the Magiclnfo Server Program perform Network mode When using MagiclInfo with the device directly connected to LCD Display execute Device mode Press ESC to directly go to the Magiclnfo Window screen To setup Magiclnfo on a Windows screen a keyboard and mouse are required To setup Magiclnfo on a Windows screen refer to the Magiclnfo Server Help It is highly recommended not to turn off the AC power during an operation For pivoted LCD Displays ticker transparency is not supported For pivoted LCD Displ
72. eAlet Lamp Control Help Anaktaaan Denial Faulty Device U SelectAll Clear All Refresh Idle 1 F Audio Al Input Main Basic information required to adjust Audio is displayed in the display window Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected and the default settings will be displayed if all display IDs are selected by clicking All and Select If a value is changed in this screen the current mode will automatically switch to custom mode 1 Audio Controls audio settings for all input sources 2 Bass Adjusts Bass of the selected display 3 Treble Adjusts Treble of the selected display 4 Balance Adjusts Balance of the selected display 5 SRS TS XT SRS TS XT Sound ON OFF of the selected display 6 Sound Select Select either Main or Sub when PIP is On This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed amp The Input source of Magic nfo works only on Magic nfo model The Input source of TV works only on TV model Setting a ii pli Uk mage Lock 1 Click Settings of the main icons and the Settings Control screen appears Multiple Display Control Fie AddaDevice Remote Control SaletyLock Faul Device Alert Lamp Control Help Faulty Device 0 Select All Clear All Refresh Idle N saa Jo ofe eee PC BHC pas g
73. eating Using the Software Note This monitor driver is certified by Microsoft and installing it will not damage your system The certified driver will be posted on Samsung Monitor homepage http www samsung com Installing the Monitor Driver Manual Microsoft Windows Vista Operating System 1 Insert your Manual CD into your CD ROM drive 2 Click Xstart and Control Panel Then double click on Appearance and Personal ization 3 Click Personalization and then Display Settings oem mmm mm AA AA YY YY rer ar ee el a ee er cee a F iea TEDS mwa kal ee ee TS ara Ca aaa a ika Wa ie lng a a ang Ee keem eee ge maan maga il a a a m a mamana ee ee ee ee a pa Bajd a eg le a ag os es ey r ed i ma ee aag or eee ee 4 Click Advanced Settings fe aplay Settings Sorts Dang Be Kora ba makeh pou eer L plaig Monitor on AA Gefore iG LE fheir Cp F 5 Click Properties in the Monitor tab If the Properties button is deactivated it means the configuration for your monitor is completed The monitor can be used as is Using the Software If the message Windows needs is displayed as shown in the figure below click Continue Mirae Tait a Ganang PrP Mantan Cire Morwhor Getir irh refresh rate bo Heriz a Hae meti a ma mi Carol deeply Gearing Pia check boa dload yew fo akal damia exten Fat Sha monitor cannot Genuine comectiy Thee muy lead ko an usable Sag
74. ected monitor on 2 Off Time Sets the time in hours in minutes and as AM PM for turning the selected monitor off 3 Volume Selects the volume when the selected monitor is turned on 4 Source Selects the external input source that will be displayed when the selected monitor is turned on 5 Holiday Applies the Holiday Management function to the Timer 6 Repeat Available selections include Once EveryDay Mon Fri Mon Sat Sat Sun and Manual Once The Timer goes off only once EveryDay EveryDay The Timer repeats daily Mon Fri The Timer repeats from Monday through Friday Mon Sat The Timer repeats from Monday through Saturday Sat Sun Sat Sun The Timer goes off on Saturday and Sunday Manual Select a day of the week you want the Timer to go off 2 Setting Holiday Management The Holiday Management function specifies the dates in which the monitor will not be turned on or off by the Timer Holiday Management 1 Specifies the date 2 Delete All Deletes all of the holidays 3 Add Adds the specified date 4 mg Deletes the schedule in the selected line k The Holiday Management function can be turned on or off in the Timer setup menu The Input source of Magicl nfo works only on Magicl nfo model amp The Input source of TV works only on TV model Time Control is available only for the displays for which the power status is ON Only enabled for a TV when Source is set to TV
75. ed by installation at customer s discretion Dimensions MA Notice For securing the bracket on a wall use only machine screws of 6 mm diameter and 8 to 12 mm length Accessories sold separately e Dimension with other accessories 135 3 73 5 2 O Sto 5 TE ER 2 5 217 0 281 5 543 Introduction Wall Bracket Installation e Contact a technician for installing the wall bracket e SAMSUNG Electronics is not responsible for any damages to the product or harm to customers when the installation is done by the customer e This product is for installing on cement walls The product may not stay in place when installed on plaster or wood Components Only use the components and accessories shipped with the product a A Ng IF IN NG Wall Bracket 1 Hinge Left 1 Right Plastic Screw Screw Anchor 1 Hanger A 11 B 4 11 4 To mount the product on the wall bracket The shape of the product may vary depending on the model The assemblies of the plastic hanger and the screw are the same 1 Remove the 4 screws on the back of the product 2 Insert the screw B into the plastic hanger Bll g i A Notice e Mount the product on the wall bracket and make sure it is properly fixed to the left and right plastic hangers e Be careful when installing the product on the bracket as fingers can be caught in the holes Introduction e Make sure the wall bracket is securely fixed to
76. elect button or checkboxes e TV Mode Multiple Display Control _File Remote Control Safety Lock Port Selection Lamp Control Options Help SAMSUNG ictal Clear Refresh Choose Input Source PC Image Size is BHC S Video 1 em CC qn Componen B ta LL api wg DTV Settings Maintenance e PC Mode ES Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Help SAMSUNG DIGIaN Select Clear Refresh Choose Input Source PC SIS S Video 7 Pat Compo ITO ingat 9 i a om mm a 1 d CILI a Maintenance Info Grid shows some basic information necessary to Input Source Control PC Changes the Input Source of the selected display to PC BNC Changes the Input Source of the selected display to BNC DVI Changes the Input Source of the selected display to DVI TV Changes the Input Source of the selected display to TV DTV Changes the Input Source of the selected display to DTV AV Changes the Input Source of the selected display to AV 7 S Video Changes the Input Source of the selected display to S Video 8 Component Changes the Input Source of the selected display to Component 9 Magicl nfo The Input source of Magiclnfo works only on Magicl nfo model 10 HDMI1 HDMI2 Changes the Input Source of the selected display to HDMI 11 DP Switches the inp
77. es noise such as horizontal stripes If the noise persists even after Fine tuning repeat it after adjusting the frequency clock speed Adjusting the LCD Display Position Adjusts the screen location horizontally and vertically Auto Adjustment Auto Adjustment Please Wait The values of Fine Coarse Position are adjusted automatically By changing the resolution in the control panel the auto function is performed Note Available in PC mode only Signal Balancel This is used to make up for the weak RGB signal transmitted by a long signal cable ry Note e Not available when Dynamic Contrast is set to On e Available in PC mode only Signal Balance Selects either On or Off with the signal balance Signal Control Note Available when Signal Balance is set to On 1 R Gain 2 G Gain 3 B Gain 4 R Offset 5 G Offset 6 B Offset Sizel Adjusting the LCD Display pa Pull Ore Signal Balance Dynamic Contrast Lamp Control Picture Reset The Size can be switched 1 16 9 2 4 3 PIP Picture Adjusts the PIP Screen Settings Note e Available Modes PIP On 1 Contrast pi a Adjusts the Contrast of the PIP window on the screen 2 Brightness Adjusting the LCD Display Adjusts the Brightness of the PIP window on the screen 3 Sharpness aa Adjusts the Sharpness of the PIP window on the screen 4
78. f all display IDs are selected by clicking All and Select If a value is changed in this screen the current mode will automatically switch to custom mode 1 Picture PC Available only for PC BNC DVI and DP 2 Contrast Adjusts Contrast of the selected display 3 Brightness Adjusts Brightness for the selected display 4 Red Adjusts red Color of the selected display Available only for NT 5 Green Adjusts green Color of the selected display Available only for NT 6 Blue Adjusts blue Color of the selected display Available only for NT 7 Color Tone Adjusts the Color Tone for the selected display 8 Color Temp Adjusts the Color Temp for the selected display 9 Brightness Sensor Adjusts the Brightness Sensor for the selected display 10 Dynamic Contrast Adjusts the Dynamic Contrast for the selected display Brightness Sensor may not be supported depending on the product The Input source of Magicl nfo works only on Magicl nfo model The Input source of TV works only on TV model Color Temp is only enabled if the Color Tone is set to Off This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed DP may not be supported depending on the product Audio 1 Click Settings of the main icons and the Settings Control screen appears Multiple Lisplay Control File AddaDevce Remote Control SetetyLock FaultDewc
79. he Installation Note Problems related to the LCD Display installation and their solutions are listed Q The LCD Display screen flickers A Troubleshooting Check if the signal cable between the computer and the LCD Display is securely con nected Refer to Connecting a Computer Problems related to the Screen Note Problems related to the LCD Display screen and their solutions are listed Q A Pra 7 O F O gt O 5 O O The screen is blank and the power indicator is off Ensure that the power cord is firmly connected and the LCD Display is on Refer to the Connecting a Computer No signal message Ensure that the signal cable is firmly connected to the PC or video sources Refer to the Connecting a Computer Ensure that the PC or video sources are turned on Not Optimum Mode message Check the maximum resolution and the frequency of the video Adaptor Compare these values with the data in the Preset Timing Modes Chart The picture rolls vertically Check if the signal cable is securely connected Re connect it if necessary Refer to Connecting a Computer The image is not clear picture is blurred Run Frequency Coarse and Fine tuning Turn on again after removing all accessories video extension cable etc Set the resolution and frequency to the recommended ranges The picture image is unstable and shakes Check if the resolution and frequency set for the computer video ca
80. id using Grey Colors which can cause Image retention easily Avoid Colors with big difference in luminance Black amp White Grey Information pasas oa rg Change the characters Color periodically e Use Bright Colors with little difference in luminance Cycle Change the characters Color and background Color every 30 minutes FLIGHT TIME FLIGHT TIME FLIGHT TIME OZ348 20 30 e Every 30 minutes change the characters with movement m FLIGHT TIME FLIGHT TIME 0348 20 30 02348 20 30 Step1 Step 3 e Have the images and logo cycle periodically Cycle Display moving image together with Logo for 60 seconds after 4 hours in use e The best way to protect your monitor from Image retention is to turn the Power off or set your PC or System to operate a Screen Saver Program when you are not using it If these guidelines are not followed it may affect your warranty Apply the Screen Pixel function on Product e Apply the Screen Pixel function Symptom Dot with Black Color move up and down FLIGHT TIME H OZ348 20 30 UA102 21 10 e Apply the Screen Bar function Symptom Horizontal Vertical Bar with Black Color move up and down FLIGHT TIME Horizontal Bar OZ5 20 3U UA102 21 10 E3 Apply the Screen Erasing function on Product Information e Apply the Screen Erasing function Symptom 2 Vertical blocks move while erasing the display
81. ilable only for the displays where the power status is ON Troubleshooting 1 The display you wish to control does not appear on the System Info Grid Check if the entered IP address is correct and check the connection status of the Ethernet cable Check the displays to see if any of the other displays connected have the same ID If more than one displays have the same ID those displays are not properly detected by the program due to data conflict For monitors that support a Set ID between 0 to 99 you have to set the Set ID to a value between 0 and 99 Note Check if the Set ID of the monitor is a value between 0 and 99 set the value using the Display menu 2 The display you wish to control does not appear on the other Control Info Grids Check to see if the display power is ON You can check this in System Info Grid Check if you can change the input source of the display 3 The dialogue box appears repeatedly E Check to see if the display you wish to control is selected b 4 Both On Timer and Off Timer have been set but different time is showing Apply current time to synchronize the display clocks 5 The remote may not function properly when you turn off the remote Function disconnect the Ethernet cable or exit the program in an Irregular manner Rerun the program and turn the remote function again to Restore normal functions lt Note gt This program may malfunction due to problems in communication circu
82. ire More Film Mode Lamp Control Picture Reset Dynamic Contrast automatically detects the distribution of the visual signal and adjusts to create an optimum contrast 1 Off 2 On Note This function is disabled when PIP or Energy Saving is On Lamp Control Hu esse Adjusts the inverter lamp in order to reduce energy consumption Note Not available when Dynamic Contrast is set to On Picture Reset L sii Sound Reset picture settings Yes Mo Reset the screen settings Available Modes J PC DVI DisplayPort e Elav fF Component gt HDMI M Magicinfo gt filtv Adjusting the LCD Display Note To watch TV on the product connect a TV tuner box sold separately Note Using Magiclnfo To use Magiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the already included network box to HDMI IN 2 MAGICINFO on the product To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and connect the Magjiclnfo output on the network box to HDMI IN 2 MAG ICINFO on the product Model 1 n Standard Custom Music Auto Volume Movie SRS TS XT Speech Speaker Select Internal Sound Reset The LCD Display has a built in high fidelity stereo amplifier i Standard Selects Standard for the standard factory settings 2 Music Selects Music when watching music videos or concerts 3 Movi
83. itch to custom mode Audio Controls audio settings for all input sources Bass Adjusts Bass of the selected display Treble Adjusts Treble of the selected display Balance Adjusts Balance of the selected display SRS TS XT SRS TS XT Sound ON OFF of the selected display Sound Select Select either Main or Sub when PIP is On The Input source of Magicl nfo works only on Magicl nfo model The Input source of TV works only on TV model This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed We Settings mage Lock 1 Click Settings of the main icons and the Settings Control screen appears Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Help Select Refresh Image Lock Coarse Fine Position Auto Adjustment 3 Info Grid shows some basic information necessary to Settings Control 1 Image Lock Available only for PC BNC 2 Coarse Adjusts Coarse of the selected display 3 Fine Adjusts Fine of the selected display 4 Position Adjusts Position of the selected display 5 Auto Adjustment Self Adjust to the incoming PC signal The Input source of Magicl nfo works only on Magicl nfo model amp The Input source of TV works only on TV model k Settings Control is available only for the displays for which the power status is ON p9 Mai
84. its or interference from electronic appliances nearby Please make selection in the information grid before controlling Settings Value Display In Multiple Display Mode When there are more than one displays connected the settings values are displayed as follows 1 No selection Displays the Factory Default Value 2 Selected one display Fetches and displays the settings value for the selected display 3 Selected one display ID1 and add another display 1D3 The program which was displaying the settings value of ID 1 fetches and displays the value of ID3 4 If all sets are selected at the same time by clicking All and Select the default value will be restored Copyright 2003 2010 Samsung Electronics Co Ltd All rights reserved Adjusting the LCD Display Input Available Modes J PC DVI DisplayPort EV AV 4 Component CJ HDMI M Magicinfo itv Note To watch TV on the product connect a TV tuner box sold separately IG Note Using Magiclnfo To use Magjiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the already included network box to HDMI IN 2 MAGICINFO on the product To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and connect the Magjiclnfo output on the network box to HDMI IN 2 MAG ICINFO on the product Source Lista L 175 DVI Ay Component HOMIL DisplayPort Use to select PC HD
85. k the product so that they can safely use it in public locations Since the shape and usage of the locking device may differ depending on the model and the man ufacturer for more information refer to the User Manual supplied with the locking device for more information Note You must purchase the Kensington Lock separately To lock the product follow these steps 1 Wrap the Kensington lock cable around a large stationary object such as a desk or chair 2 Slide the end of the cable with the lock attached through the looped end of the Kensington lock cable 3 Insert the Kensington Lock into the se curity slot on the back of the dis play 4 Lock the lock QD Note e These are general instructions For exact instructions see the User Manual sup plied with the locking device e You can purchase the locking device from an electronics store an online shop or our service Center Note The power switches of both of the monitor and the network box must be turned on for the network box to operate normally Remote Conirol Note The performance of the remote control may be affected by a TV or other electronic device operating near the LCD Display causing a malfunction due to interference with the frequency power Oorr 3 Number Buttons DEL GUIDE button voL Introduction power Corr Number Buttons DEL GUIDE button VOL t SOURCE
86. kk The Input source of Magicl nfo works only on Magicl nfo model Color Temp is only enabled if the Color Tone is set to Off amp The Input source of TV works only on TV model k This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed 7 Settings Picture PC 1 Click Settings of the main icons and the Settings Control screen appears Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Help Select Clear D Idie Refresh PC BNC OWI DP 2 Contrasi 100 Brightness 100 Red 43 Greg DE Biu Hill Color Tone Color Temp 10000K Basic information required to adjust settings is displayed Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected and the default settings will be displayed if all display IDs are selected by clicking All and Select If a value is changed in this screen the current mode will automatically switch to custom mode 1 Picture PC Available only for PC BNC DVI and DP 2 Contrast Adjusts Contrast of the selected display 3 Brightness Adjusts Brightness for the selected display 4 Red Adjusts red Color of the selected display Available only for NT 5 Green Adjusts green Color of the selected display Available only for NT 6 Blue Adjusts blue Color of the selected dis
87. l the video source inputs twice in sequence looking for an active video source returning back to the first video source in the sequence if no video is found 1 Off 2 On Primary Source Recovery Source AutoSwitch Primary Source Secondary Source 4 Move Enter O Return When Primary Source Recovery is On only the Primary Source and Secondary Source video source selection will be searched for active video The Primary Source will be selected if active video is found if no video is found the Sec ondary Source will be selected if no video is found in Secondary Source again the no input signal is displayed 1 Off 2 On Primary Source Source AutoSwitch Primary Source Recovery Secondary Source Move Enter Return Adjusting the LCD Display Specify Primary Source for the automatic input source Secondary Source Source AutoSwitch Primary Source Recovery Primary Source Move Enter O Return Specify Secondary Source for the automatic input source Picture PC DVI DisplayPort Magiclnfo Mode e If connected to a PC set Edit Name to DVI PC and enjoy video or audio content saved on the PC e If connected to an AV device set Edit Name to DVI Device and enjoy video or audio content saved on the AV device Available Modes JPC DVI DisplayPort gt Eav j 7 Component CJHDMI i 7 Magicinfo rv Note To watch TV on the product connect a TV tuner box
88. lable only for NT 7 Color Tone Adjusts the Color Tone for the selected display 8 Color Temp Adjusts the Color Temp for the selected display 9 Brightness Sensor Adjusts the Brightness Sensor for the selected display 10 Dynamic Contrast Adjusts the Dynamic Contrast for the selected display Brightness Sensor may not be supported depending on the product The Input source of Magicl nfo works only on Magicl nfo model k Color Temp is only enabled if the Color Tone is set to Off The Input source of TV works only on TV model k This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed amp HDMI2 may not be supported depending on the product 5 ad cy Setting Picture PC 1 Click Settings of the main icons and the Settings Control screen appears Mulhple Display Control File AddaDewce Remote Control SatetyLock Fault Device Alert Lemp Control Help Faulty Device U Select All Clear All Refresh ne idle 1 7 Picture PC nput PC i PC BNC Dwi DP 2 Contrast 5G maa Brightness Fill 4 Red Green w o 6 Ei Color Tone LJ i 8 J Color Temp i Brightness Sensor 10 Dynamic Contrast ke Basic information required to adjust settings is displayed Settings for the corresponding SET will be imported and displayed on the slider if a display ID is selected and the default settings will be displayed i
89. le in the Self Test mode the LED power indicator remains green and the figure moves around on the screen No Signal If your LCD Display screen remains blank after using the previous procedure check your video controller and computer system your LCD Display is functioning properly 4 Turn off your LCD Display and reconnect the video cable then turn on both your com puter and the LCD Display Warning Messages You can even view the screen at a resolution of 1366 x 786 However you will receive the following message for a minute You can choose to change the screen resolution or stay in the current mode during that time If the resolution is more than 85Hz you will see the black screen because the LCD Display does not support over 85Hz Not Optimum Mode Recommended Mode 1366 X 768 60Hz Note Refer to Specifications 5 Preset Timing Modes for the resolutions or frequencies supported by the LCD Display Maintenance and Cleaning 1 Maintaining the LCD Display Case Clean with a soft cloth after disconnecting the power cord Troubleshooting ex Do not use benzene thinner or other flammable sub stances 2 Maintaining the Flat Panel Display Screen Clean with a soft cloth cotton flannel e Never use acetone benzene or thinner ts a They may cause flaws or deformation of the screen surface e The user is responsible for any damage caused by using these substances Symptoms and recommended
90. long period of time disconnect the power cord from the power outlet e Otherwise this may result in overheating or fire due to dust and may result in fire due to electric shock or leakage 3 Do not place any heavy items or toys or confectionery such as cookies etc that may attract the attention of children and to the product e Your children may hang onto the product causing it to fall and this may result in personal injury or death L Be careful that children do not place the battery in their mouths when removed from the remote control Place the battery in a lo cation that children or infants cannot reach e f children have had the battery in their mouths consult your doctor immediately Safety Instructions L When replacing the battery insert it with the right polarity e Otherwise the battery may become damaged or it may cause fire personal injury or damage due to leakage of the internal liquid J Use only the specified standardized batteries and do not use a new battery and a used battery at the same time e Otherwise the batteries may be damaged or cause fire per sonal injury or damage due to a leakage of the internal liquid L The batteries and rechargeable batteries are not ordinary re fuse and must be returned for recycling purposes The customer is responsible for returning the used or rechargeable batteries for recycling e The customer can return used or rechargeable batteries to a near
91. mage to your monitor J Ensure that at least two persons lift and move the product e Otherwise it may be dropped and cause personal injury and or damage the product When installing the product in a cabinet or rack make sure that the front end of the bottom of the product does not project out e Otherwise it may fall or cause personal injury e Use a cabinet or rack of a size appropriate to the product Safety Instructions 3 DO NOT PLACE CANDLES MOSQUITO REPELLANT CIG ARETTES AND ANY HEATING APPLIANCES NEAR THE dn PRODUCT e Otherwise this may result in fire Keep heating appliances as far away from the power cord or the AV product as possible S ES T PA e ee e Otherwise this may result in electric shock or fire 3 Do not install it in a badly ventilated location such as a bookcase or closet e Otherwise this may result in fire due to an increase in the in ternal temperature L When putting the product down make sure to put it down softly e Otherwise this may result in damage to the screen display J Do not place the front of the product on the floor e Otherwise this may result in damage to the screen display 3 Ensure that an authorized installation company installs the wall mount e Otherwise it may fall and cause personal injury e Make sure to install the specified wall mount 3 Install your product in a well ventilated location Ensure that the
92. mote Control Soletylock Feul Desce Alert Lamp Control Help paraan Faulty Device Select Al Clear All Refresh Idle k Baa O T Fi size 1 PIP size o O oome E Network Sf Tz All Input E aaa re Lay at E Ny Ss 7 17 38 Wo 1 OFF ae oo Large F Small Double 1 7 al Dowble 2 Double 3 Q Je Info Grid shows some basic information necessary to PIP Size Control 1 PIP Size Shows the current PIP Size of the display in use 2 OFF Turns off the PIP of the selected display 3 Large Turns on the PIP of the selected display and changes the size to Large 4 Small Turns on the PIP of the selected display and changes the size to Small 5 Double 1 Turns on the PIP of the selected display and changes the size to Double 1 6 Double 2 Turns on the PIP of the selected display and changes the size to Double 2 Double 3 Picture By Picture Turns on the PBP of the selected display and changes the size to Double 3 PIP Size can be controlled with turning on the LCD Display power amp The Input source of TV works only on TV model amp The Input source of Magicl nfo works only on Magicl nfo model NI NG PIP PI P Source 1 Click PIP of the main icons and the PIP control screen appears Multiple Display Control File AddeDevice Remote Control Sefety Lock Fault Device Alert Lamp Control PA FPauliy Device 0
93. nced Themer Cia Juren Terem aman Balbnga Lare n Fiap mej Mhay biorda cers Mr Pabo Dji Sen dete Greka pisiy Hikghandi 37 bet E E 8 EE I EE Cae cance TOJA by FES pikwa Plug and Play Monitor and 30 Prophet IN Properties 2 s orel General Pigra HA al Pag and Plage Honko Sd Device Selection horace Piore piire Jonen netemch ata 60 Heitz C Hide eden that Ehiz PAOS MNL CBEN Ciemi thea cheek boa o beheck da Wg mndi retake Click Update Driver Direc Provides Diree Date Micrownlt Apo Dies Wes moe S12001 0 igtal Sigra Update Duig Bef Pack Dra Upa io iha daya To alaia aa kian To wereld Whe hives uliraroed Select Don t search will 2 Colo Conection Tisubisahast Color Aanagamani PB En iplay rak haa sree play e pagasa Thi mag bead bo sn Lara sib dag and select Install from a list or Miceomoft Window bf Pubilahar To wees cite alld iha hira Pee IP ihe deseg kada alter upahan Hee dies rol back ko tne previously mababad cadet Umm Duke id Phag ardi Fiap Moewtor Devica hps Marilesz Fl el acinar Ghardand mon o lipas Location on 20 Piggies Ik Diviga Laud UG AA IP pau ane hasang Pah Iha dawa chock Trouhieshoct la basil ih A cabbies root Device ung Ulsa iha Gee erate then click Next button Hardware Update Wizard Welcome to the Hardware Update wizard Thin wese hel
94. nput sources for active video Note If the display TV source is active TV tuner connected to the display the Source AutoS witch search function becomes inactive The display will remain in the TV source Source AutoSwitch selection and PIP function If the Source AutoSwitch selection is set to On the PIP function will not work the Source AutoSwitch selection must be set to Off for the PIP feature to work When the Source AutoSwitch selection is On and or the Primary Source Recovery is On the display power saving mode becomes inactive When Primary Source Recovery is On only the Primary Source and Secondary Source selection are available and they are interchangeable and selectable at will Refer to PIP gt Source for compatible signals for each primary input source Adjusting the LCD Display Source AutoSwitch Primary Source Recovery Primary Source Secondary Source Move Enter Y Return When the Source AutoSwitch is On the display video source will automatically be searched for active video The Primary Source selection will be activated if the current video source is not recognized Secondary source selection will become active if no primary video source is available If the primary or secondary source is not recognized the display will search again if no active video is found the display will show the no input signal message When the Primary Source selection is set to All the display will search al
95. ntenance NN Lamp Control 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Contro Idle Refresh Lamp Control Auto Lamp Control Hour Minute Apply Manual Lamp Control 3 Ambient Light Reference co fg Lamp Value O Je An Info Grid showing several basic data items appears 1 Maintenance Allows the Maintenance Control function for all input sources 2 Lamp Control Automatically adjusts the backlight of the selected display at a specified time The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control Allows you to adjust the backlight of the selected display regardless of the time The Auto Lamp Control automatically turns off if you adjust using the Manual Lamp Control 3 Ambient Light Detects the ambient light intensity at the designated monitor and automatically adjusts the picture brightness You can specify a Reference value and designate a monitor that will automatically determine Lamp Value the light intensity from the lamp based on the ambient light intensity Ambient Light is only supported for models that have a brightness sensor and is only enabled when Ambient Brightness Mode is selected in the Lamp Control menu Auto Lamp Control and Manual Lamp Control are only enabled when User Control Mode is selected in the Lamp Contr
96. ntrol PC BNC Only e Function Personal Computer controls PC system screen automatically e Get Auto Adjustment Status None e Set Auto Adjustment Header command DATA DATA Length CheckSum Auto Adjustment 0x00 Always 1 Auto Adjust ment e Ack Introduction Header OM DATA ack Nak r CMD Val mand Length Check Sum OxAA OxFF 3 A ox3p Auto Ad justment e Nak com DATA EIRE Length AENA um ERR Error code that shows what occurred error is e Video Wall Mode Control e Function Personal Computer converts Video Wall Mode of TV Monitor when Video Wall is ON Only works with TV Monitor where Video Wall is on Does not operate in Magiclnfo e Get Video Wall Mode CheckSum o e Set Video Wall Mode Header command DATA DATA Length CheckSum OxAA Ox5C 1 Video Wall Mode Video Wall Mode Video Wall Mode code to be set on TV Monitor 1 Full O Natural e Ack Header Ou DATA ack Nak r CMD Val mand Length Check Sum Video Wall Mode same as above Introduction e Nak com DATA en Length ack as pabaon um ERR Error code that shows what occurred error is Safety Lock e Function Personal Computer turns Safety Lock function of TV Monitor ON OFF Can operate regardless of whether power is ON OFF e Get Safety Lock Status CheckSum o e Set Safety Lock Enable Disable Header command DATA DATA Length CheckSum
97. ol menu The Maintenance Control feature is available only for the displays whose power status is ON The Input source of Magicl nfo works only on Magicl nfo model The Input source of TV works only on TV model Maintenance Ww Scroll 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen 1 Multiple Display Control File Remote Control SafetyLock Port Selection Lamp Control Options Refresh scroll Pixel Shift Tine Harironlal Dot Vertical Line Apply Safety Screen jor jor sci interwal Dine Apply Safety Screen Scroll This function is used to remove the afterimages that occur when a still screen is displayed on the selected display for a long time Pixel Shift This allows the screen to be moved finely at the specified time interval Safety Screen The Safety Screen function is used to prevent afterimages from occurring when a still screen is displayed on the monitor for a long time The Interval item is used to set the repetition cycle in hour units and the Time item is used to set the time when the Safety Screen function must be performed The Type item can be set to Scroll Pixel Bar Eraser All White or Pattern Safety Screen2 This function is used to prevent afterimages from occurring There are five 5 types that you can select and control with this function For the Scroll type the Time item can be set to 1 2
98. om http www samsung com http www samsung com http www samsung com http www samsung com 1800 SAMSUNG 726 7864 http www samsung com 0800 329 999 1800 29 3232 http www samsung com http www samsung com Terms Appendix Asia Pacific 02 689 3232 VIETNAM 1 800 588 889 http www samsung com Middle East BAHRAIN 8000 4726 http www samsung com Egypt 08000 726786 http www samsung com JORDAN 800 22273 http www samsung com Morocco 080 100 2255 http www samsung com Oman 800 SAMSUNG 726 7864 http www samsung com Saudi Arabia 9200 21230 http www samsung com TURKEY 444 77 11 http www samsung com U A E 800 SAMSUNG 726 7864 http www samsung com Africa NIGERIA 0800 SAMSUNG 726 7864 http www samsung com SOUTH AFRICA O860 SAMSUNG 726 7864 http www samsung com Dot Pitch Vertical Frequency Horizontal Frequency Interlace and Non Interlace Methods Plug amp Play Resolution The image on a monitor is composed of red green and blue dots The closer the dots the higher the resolution The dis tance between two dots of the same Color is called the Dot Pitch Unit mm The screen must be redrawn several times per second in order to create and display an image for the user The fre quency of this repetition per second is called the Vertical Frequency or Refresh Rate Unit Hz Example If the same light repeats itself 60 times per sec ond this is regarded as 60 Hz Th
99. on in the BIOS SETUP of the computer Refer to the Windows Computer Manual A Windows ME 2000 Control Panel gt Display gt Screen Saver Set the function in the BIOS SETUP of the computer Refer to the Windows Computer Manual Q How can I clean the outer case LCD Panel A Disconnect the power cord and then clean the LCD Display with a soft cloth using either a cleaning solution or plain water Do not leave any detergent or scratches on the case Do not let any water enter the LCD Display Note Before calling for assistance check the information in this section to see if you can remedy any problems yourself If you do need assistance please call the phone number on the In formation section or contact your dealer Specifications General General Model Name 320MX 3 320MP 3 320MXN 3 320MPN 3 LCD Panel Size 31 5 inches 80 cm Display Area 697 68 mm H x 392 25 mm V Synchronization Horizontal 30 81 kHz Vertical 56 85 Hz Display Color 16 7M true Resolution Optimum resolution 1366 x 768 60 Hz Maximum resolution 1920 x 1080 60 Hz Maximum Pixel Clock 148 5MHz Analog Digital Power Supply This product supports 100 240 V Since the standard voltage may differ from country to country please check the label on the back of the product Signal connectors D sub Component DVI D In VCR HDMI 1 2 RS232C In Out DP DC Out Ster eo Audio In Out Audio In L R RJ45 USBx3
100. onnected Opens the on screen menu and exits from the menu or closes the adjustment menu Returns to the previous menu Exits from the menu screen Magiclnfo Quick Launch button Note Using Magiclnfo e To use Magiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the already included network box to HDMI IN 2 MAGICINFO on the product e To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and con nect the Magiclnfo output on the network box to HDMI IN 2 MAGICINFO on the product e Be sure to call an installation expert of Samsung Electronics to install the product Introduction e The warranty becomes invalid if the product is installed by someone other than a profes sional authorized by Samsung Electronics e A Samsung Electronics service center can provide details Tilt Angle and Rotation 1 ag 2 l i eit 1 The product can be tilted up to 15 degrees from a vertical wall 2 Touse the product in portrait mode rotate it clockwise so that the LED indicator is at the bottom Ventilation requirement 1 Vertical wall mount condition lt Side view gt gt t A min 40 mm B Ambient temperature Measuring point lt 35 C e When installing the product onto a vertical wall be sure there is a 40 mm space or more behind the product for ventilation as shown above and maintain the ambient temperature at 35 C or lower
101. orks with models include TV e Get Screen Mode Status CheckSum o e Set Picture Size Header basal DATA DATA Length CheckSum kad lai 8 1 Screen Mode Screen Mode Screen Mode code to be set on TV Monitor e Ack com DATA Check Introduction OxAA OxFF 3 aN ox18 Screen Mode Screen Mode Same as above e Nak DATA EE e Ka A AG KAN paan um OxFF oda ERR ERR Error code that shows what occurred error is e Screen Size Control e Function Personal Computer recognizes the screen size of TV Monitor e Get Screen Size Status CheckSum o Header OM DATA nckiNak r CMD Val mand Length Check Sum 3 ja oo Sge Size Screen Size Screen Size of TV Monitor Range 0 255 Unit Inch DATA a SE oe cones payan um OxFF ode ERR ERR Error code that shows what occurred error is ex PIP ON OFF Control e Function The PC turns the PIP function of a TV or Monitor ON OFF This does not operate in Magiclnfo mode e Get the PIP ON OFF Status Introduction CheckSum o e Set the PIP ON OFF Header command DATA DATA Length CheckSum 0 l PP PIP The PIP ON OFF code to set for the TV or Monitor 1 PIP ON 0 PIP OFF e Ack com DATA um DAA 3 w oc Pe PIP Same as above e Nak COM DATA CE Length AKNAS papang um ERR Error code that shows what occurred error is e Auto Adjustment Co
102. our monitor from the list of monitor models on the screen and click Next Skeci the dintne draa you ward to nakal for thia hardane a pa ghee deed eich pan Pain ieee fee Pao ein bana pa Sane Pa sid Pha ee pee mc bi alal Clie Harri a Anakan haa sulod updated your dhan sofware akan Baa Lanha acl ualang Pa derre paga Fpa Pk rai x Sate oe Top arm es ais pina Pag wen His Tip pcan Pa deae KP ma ka Pa chat ei Taa Cno Pap anim area Tagal Na jae aa WIL TENETE GO daptar Monitor Troubleshoot Color Management enor Type Sa bang Fine Mono ana NY Monon Satanas Screen refresh rate 80 hertz Gf Hide modes that the monitor cannot display Clarin than cheeck ben apa you ko peci daplay modes that thig monior cannot display correctly This may lead to an unusabie aag T This i my main maagor d Extend the desktep onto thm mortor Microsoft Windows XP Operating System Using the Software Insert CD into the CD ROM drive Click Start Panid Bete ibe E gt Fely Pte il aa KHotapaodi ig Pi a paiba Ww Pairt E3 Windows odio Mara PERN Caplorar bi amd Movi Pako 0 rage as Paa EEJ Bun Click Display oon eee Pee Down IE 2y Piy acest ences age Panes and Faran 7 rep and Suoport Control Panel then click the Appearance and Themes icon icon and choose the Settings tab then click Adva
103. pa pou naal solas bor Piia arad Plage Mordi If pou hades come wilh an mabalian CO or Roney disk inih ik nee A attest cho pou waned kas waned ID do CC ball E a gutoratically Fienommercded a rta hom a ist on pek kapa Dik Next lo continue L Cmo then click Next and then click Have disk Using the Software Hardware Update Wizard hardware Update Wizard Fieste chorta yo poach and incl alain opines Gv Pr Task the dovide dive pou want bo install le this handaan D esch iy He ber drva in these locate emi Skee tho mamulat ard madal of pour haichvats devace one ihan ckek Hasi Il you have a dak that panissa tha diss pou wasnt lo nala obok Hawa Chink Lise ha chak basa baka ka kmi ca parad the dakal seach vadh cludes kea pall ardceminnatee mecha The beth dmo bound wal be nalaled poe companba Federaal Mista W Pug ered Pay Honto 2 Dont readh yall chesse the drva bo reat Chose the option ko select the desce draa homa bet Wide does mot guarentee hat Uh dan pou hoo yell ba ha bagi makoh kor pour hare if That dira in cpt grad Cie 7 Click the Browse button then choose A D Driver and choose your monitor model in the model list and click the Next button install From Disk Hardward Update Wizard Selec the device divei you want bo inalali for thia harders rebel he manulacbusas matallaion dak and then make sue thal the conect dine E selected bebo a Tiigi tho Aria
104. play Available only for NT 7 Color Tone Adjusts the Color Tone for the selected display 8 Color Temp Adjusts the Color Temp for the selected display 9 Brightness Sensor Adjusts the Brightness Sensor for the selected display 10 Dynamic Contrast Adjusts the Dynamic Contrast for the selected display DP may not be supported depending on the product Brightness Sensor may not be supported depending on the product The Input source of Magicl nfo works only on Magicl nfo model amp The Input source of TV works only on TV model k Color Temp is only enabled if the Color Tone is set to Off This feature is available only for the displays whose power status is ON and if no selection is made the factory default is displayed ep Settings pee Audio 1 Click Settings of the main icons and the Settings Control screen appears Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options D Idle Refresh Or All Inputs Lido aaa HO SRS TS XT sound Select Je Basic information required to adjust Audio is displayed in the display window Settings for the corresponding SET will UI O be imported and displayed on the slider if a display ID is selected and the default settings will be displayed if all display IDs are selected by clicking All and Select If a value is changed in this screen the current mode will automatically sw
105. ppear when a still picture is displayed on the screen over a long time Adjusting the LCD Display Note This function is not available when the power is turned off Pixel Shift Pixel Shift Horizontal Vertical Time 4 min To prevent after images on the screen you can use this function to have pixels move on the LCD in the horizontal or vertical direction e Off e On Horizontal Pixel Shift Vertical Time 4 min Sets how many pixels the screen moves horizontally Five adjustment levels 0 1 2 3 and 4 Vertical Pixel Shift Horizontal 4 Time 4 min Sets how many pixels the screen moves vertically Five adjustment levels 0 1 2 3 and 4 Adjusting the LCD Display Time Pixel Shift Horizontal Vertical Set the time interval for performing the horizontal or vertical movement respectively Timer Timer Mode Period Time You can set the timer for Screen Burn Protection If you start the operation to erase any residual image the operation will be performed for the set period of time and then automatically finish e Off e On Mode Timer Period Time You can change the Safety Screen Type e Bar e Eraser e Pixel Adjusting the LCD Display Period Timer Mode Time Adjust O Return Use this function to set the execution period for each mode set in the timer Time Timer Mode Feriod Adjust D Return Within
106. r example the number of TFT LCD sub pixels contained in this product are 3 147 264 Note Design and specifications are subject to change without prior notice hen the network box is connected Class A Information Communication equipment for industrial use Attention dealers and users This device is registered for EMC requirements for industrial use Class A and can be used in areas other than general households E when the network box is not connected Class B Information Communication equipment for residential use This device is registered for EMC requirements for home use Class B It can be used in allareas Class B equipment emits less electromagnetic waves than Class A equipment PowerSaver This LCD Display has a built in power management system called PowerSaver This system saves energy by switching your LCD Display to low power mode when it has not been used for a certain amount of time The LCD Display automatically returns to normal operation when you press a key on the keyboard For energy conservation turn your LCD Display OFF when it is not needed or when leaving it unattended for long periods The PowerSaver system operates with a VESA DPM compliant video card installed in your computer Use the software utility installed on your computer to set up this feature PowerSaverd State Power Indicator 320MXN 3 320MPN 3 With Net _ work Box Power Indi cator 320MX 3 320MP 3 Without Network Box No
107. rd falls in the range supported by the LCD Display If not reset them referring to the current Information under the LCD Display menu and Preset Timing Modes Ghost images are shown in the picture Check if the resolution and frequency set for the computer video card falls in the range supported by the LCD Display If not reset them referring to the current Information under the LCD Display menu and Preset Timing Modes The image is too light or too dark Adjust the brightness and contrast Refer to the Brightness Contrast O gt OF OF OD FOE Troubleshooting The screen Color is inconsistent Adjust the Color Control option in the OSD adjustment menu The Color image is distorted by dark shadows Adjust the Color Control option in the OSD adjustment menu The Color white is poor Adjust the Color Control option in the OSD adjustment menu The Power Indicator blinks The LCD Display is currently saving the changes made in the settings to the OSD memory The screen is blank and the power indicator light blinks every 0 5 or 1 seconds The LCD Display is using its power management system Press any key on the key board Problems related to Audio Note Problems related to audio signals and their solutions are listed below Q A 7 z7 O PF Q A No sound Ensure that the audio cable is firmly connected to both the audio in port on your LCD Display and the audio out port on your sound card Refer to
108. re is a clearance of more than 4 inches 10 cm from the wall e Otherwise it may result in fire due to an increase in the internal temperature LJ Bend the outdoor antenna cable downwards at the location where it goes in so that rainwater does not flow in e If rainwater enters the product it may result in electric shock or fire O 3 Install the antenna far away from any high voltage cables e Ifthe antenna touches or falls onto a high voltage cable it may result in electric shock or fire 3 Ensure that the packaging vinyl is kept away from children e Otherwise it may result in serious harm suffocation if children play with it L If the height of your monitor is adjustable do not place any ob ject or part of your body on the stand when lowering it e This may cause damage to the product or the person carrying it Clean Others Safety Instructions When cleaning the monitor case or the surface of the TFT LCD screen wipe with a slightly moistened soft cloth 3 Do not spray cleaner directly onto the surface of the product e Otherwise this may result in the discoloration and distortion of the structure and the screen surface may peel off L When cleaning the power plug pins or dusting the power outlet clean it with a dry cloth e Otherwise it may result in fire L When cleaning the product make sure to disconnect the power cord e Otherwise it may result in electric shock or
109. rent Temperature Shows the current temperature of the product Auto Power Fan amp Temperature Button Lock User Auto Color Standby Control Auto Lamp Schedule OSD Display Enables or disables Auto Power for the product e Off e On Note When Auto Power is On the product will power on automatically as soon as it is connected to power Button Lock ow o Aeaee Serongs U Fan amp Temperature Auto Power User Auto Color On Standby Control Auto Lamp 5chedule OSD Display Locks or unlocks the monitor control buttons on the product e Off e On Adjusting the LCD Display User Auto Color Auto Color Reset Auto Color Automatically adjusts the Colors Reset Resets the Color settings Note Enabled only in PC mode Standby Control Fan amp Temperature Auto Power Button Lock User Auto Color Lamp Schedule OSD Display Sets the standby mode which will be activated when no input signal is detected Off A message will read No Signal if no input signal is detected On Power saving mode will be activated if no input signal is detected Auto When no input signal is detected Power saving mode will be activated if an external device is connected Amessage will read No Signal if no external device is connected nan Note e Enabled only in PC DVI HDMI or DP DisplayPort mode e Auto will be disabled in HDMI mode Adjusting the LCD Display L
110. rogram will be installed in the default file location 7 The Start Copying Files window will appear Confirm the file location and click Next 8 The installation progress screen will appear 9 The InstallShield Wizard Complete screen will appear Click Finish Note Select Launch MDC System and click Finish The MDC Program will immediately be run Using the Software Multiple Display Control Serial MDC Ethernet MDC 10 If the installation is successfully completed the quick MDC System execution icon will appear on the desktop MDC execution icon may not appear depending on specification of computer sys tem or monitor If that happens press F5 Key Installation Problems The installation of MDC can be affected by such factors as the video card motherboard and the network environment Uninstall The MDC Program can be removed only by using the Add or Remove Programs option of the Windows Control Panel Perform the following steps remove MDC Select Setting Control Panel on the Start menu and then double click Add Delete a Pro gram Select MDC System from the list and then click the Add Delete button M Using Serial MDC M Using Ethernet MDC Serial MDC Multiple Display Control MDC Syste Introduction RS 232C OUT cms RS 232C In RS 232C In R5 232C Out R 232C Out R amp 232
111. rt Connect a DP cable to DP IN on the product and DP IN on another display AV COMPONENT AUDIO IN R AUDIO L Connect the AV COMPONENT AUDIO IN R AUDIO L port on the monitor to the au dio output port on the PC or on the external device using an audio cable O Avin Connect the AV IN terminal of your monitor to the video output terminal of the external device using a VIDEO cable AUDIO OUT Connect a headphone or an External speak er Introduction pe ouT Make sure to use connecting DC OUT ter minal to the authorized TV Tuner Box SBB DTC ZA N Otherwise this may result in damage to the product HDMLIN 1 e Connect the HDMI IN 1 terminal at the back of your LCD Display to the HDMI terminal of your digital output device us ing a HDMI cable e Up to HDMI 1 3 can be supported Note e A normal external device DVD player or camcorder etc or a TV tuner box can be connected to the HDMI IN 1 terminal e Tousea TV tuner box make sure to con nect it to the HDMI IN 1 terminal 12 HDMI IN 2 MAGICINFO e Connect the HDMI IN 2 MAGICINFO terminal at the back of your LCD Display to the HDMI terminal of your digital output device using a HDMI cable e Up to HDMI 1 3 can be supported Note Using Magiclnfo e To use Magiclnfo with an MXN 3 MPN 3 model connect the Magiclnfo output on the al ready included network box to HDMI IN 2 MAGICINFO on the produc
112. s 1D Timer T 10 8843 240 lo O Activated Day Year so Al KE Minute AMPM sj paa T mj i a sory oO i O Timer ka LA Ji Ered Timer 1 Inactivated Activate m es r Timer Inactivated Activate ENG Timer3 Inactivated Activate Pee Fea Holiday Management E Ye Info Grid shows some basic information necessary to Time Control 1 Clock Set Set the current time for the selected display PC Time To change the current time first change the PC Time 2 Timer Sets up Timerl Timer2 Timer3 and Holiday Management 3 Shows whether Timer is activated The Input source of Magicl nfo works only on Magicl nfo model amp The Input source of TV works only on TV model k Time Control is available only for the displays for which the power status is ON Time Setting up Timer and Holiday Management 1 Setting up Timer1 Timer2 and Timer3 Timer 1 Volume E Source CJ Repeat Sun Mon Tue Wed Thu Fri Sat 3 se pe o 1 On Time Sets the time in hours in minutes and as AM PM for turning the selected monitor on 2 Off Time Sets the time in hours in minutes and as AM PM for turning the selected monitor off 3 Volume Selects the volume when the selected monitor is turned on 4 Source Selects the external input source that will be displayed when the selected monitor is turned on 5 Holiday Applies the Holiday Management function to the Timer
113. s available only for TV AV and S Video k The Input source of Magicl nfo works only on Magicl nfo model k The Input source of TV works only on TV model k The Image Size Control feature is available only for the displays whose power status is ON 1 Click Time of the main icons and the Time Control screen appears Multiple Display Control Fila Remote Control Satay Lock Port Selection Lamp Control Options Help Refresh Set Clock Month Day Year w Hm Bimuria AMPM Apply Timer Timert Inactivated Activate Timer Inactivated Activate Timer Inaclivated Activate Holiday Management IN NAN Ye Info Grid shows some basic information necessary to Time Control 1 Set clock Set the current time for the selected display PC Time To change the current time first change the PC Time 2 Timer Sets up Timerl Timer2 Timer3 and Holiday Management 3 Shows whether Timer is activated The Input source of Magicl nfo works only on Magicl nfo model The Input source of TV works only on TV model k Time Control is available only for the displays for which the power status is ON Time Setting up Timer and Holiday Management 1 1 Setting up Timerl Timer2 and Timer3 Timer 1 Active Auctre Hour Minute Kata ra a Volume B Source 4 Holiday 5 one Sum Mon Tue Wed Thu Fri Sal 1 On Time Sets the time in hours in minutes and as AM PM for turning the sel
114. set of audio cables between the AV COMPONENT AUDIO IN R AUDIO L on the LCD Display and the AUDIO OUT jacks on the DVD player Note Press SOURCE on the product or remote control and select Component Then start the DVD Player with a DVD disc inserted A RGB to component cable is optional For an explanation of Component video consult your DVD manual Connections Connecting a DTV Set Top Cable Satellite Box Connect a RGB to Component cable between the RGB COMPONENT IN port on the LCD Display and the Pr Y Pg jacks on the Set Top Box Connect a set of audio cables between the AV COMPONENT AUDIO IN R AUDIO L on the LCD Display and the AUDIO OUT jacks on the Set Top Box Note e Press SOURCE on the product or remote control and select Component e For an explanation of Component video see your Set Top Box owner s manual Connecting to an Audio System 1 Connect a set of audio cables between the AUX L R jacks on the AUDIO SYSTEM and AUDIO OUT on LCD Display Connections Connecting to MAGICINFO OUT Connect the MAGICINFO OUT terminal and the HDMI IN 2 MAGICINFO terminal on the product using the DP to HDMI cable Note Applicable to the MXn 3 MPN 3 model only Connecting a LAN Cable Connect the LAN cable between the LAN port on the product and the LAN port on your PC Note Applicable to the MXn 3 MPN 3 model only Connections Connecting a USB devices
115. t Mode kili Custom Color Tone Size Digital NR More rn Ss Move ier Return ES The LCD Display has four automatic picture settings Dynamic Standard Movie and Custom that are preset at the factory Note Not available when Dynamic Contrast is set to On 1 Dynamic Adjusting the LCD Display 2 Standard 3 Movie 4 Custom Custom By using the on screen menus the contrast and brightness can be changed to your personal preference mag Note Not available when Dynamic Contrast is set to On Contrast Adjusts the Contrast Brightness Adjusts the Brightness Sharpness sali r Adjusts the picture Sharpness Color SS Ka es ee el a pe Adjusts the picture Color Tint Adds a natural tone to the display mr Note The Tint slider is only displayed when PIP input source is HDMI or AV Color Tone Lii Mode Custom Se Digital NR w More Adjusting the LCD Display The Color tones can be changed The individual Color components are also user adjustable Note Not available when Dynamic Contrast is set to On 1 Off 2 Cool2 3 Coolt 4 Normal 5 Warmi 6 Warm2 Note e If you set the Color Tone to Cool2 Cool1 Normal Warm1 or Warm2 the Color Temp function is disabled e Changing a setting in the Color Tone menu will switch the screen mode to Custom Color Temp LS ee Color temp is a measure of th
116. t e To use Magiclnfo with an MX 3 MP 3 model install inside the product a network box specified by Samsung and connect the Magiclnfo output on the network box to HDMI IN 2 MAGICINFO on the prod uct Introduction RJ 45 MDC MDC PORT MDC Multiple Display Control Program Port Connect the LAN cable to RU45 MDC on the product and LAN on the PC To use an MDC the MDC Program must be installed on the ok LO E note A Go to Multi Control and select RJ45 MDC E O as the MDC Connection RS232C OUT IN RS232C Serial PORT MDC Multiple Display Control Program Port Connect a serial cable cross type to RS232C on the product and RS232C on the PC To use an MDC the MDC Program must be installed on the PC Note Go to Multi Control and select RS232C MDC as the MDC Connection Applicable to the MXn 3 MPN 3 model only KE RGB OUT Magiclinfo video output port MAGICINFO OUT huano This is the output terminal for the video au am Ha alai dio and control signals of Magiclnfo It can be used by connecting it to the HDMI IN 2 MAGICINFO terminal using a DP to HDMI cable LAN LAN Connection Terminal Connects to a LAN cable to allow Internet or network access in Magiclnfo mode USB USB Connection Terminal Keyboard Mouse Mass Storage Device Compatible Introduction Kensington Lock slot A Kensington Lock is an anti theft device that enables users to loc
117. t CG 3 Info Grid shows some basic information necessary to Settings Control 1 Image Lock Available only for PC BNC 2 Coarse Adjusts Coarse of the selected display 3 Fine Adjusts Fine of the selected display 4 Position Adjusts Position of the selected display 5 Auto Adjustment Self Adjust to the incoming PC signal amp The Maintenance Control feature is available only for the displays whose power status is ON k The Input source of Magicl nfo works only on Magicl nfo model amp The Input source of TV works only on TV model Maintenance Ww Lamp Control 1 Click on the Maintenance icon in the Main Icon column to display the Maintenance screen Multiple Display Control File Add a Device Remote Control SofetyLock Fault Device Alert Lamp Control a User Control Made Ambient Bnghiness Mode Select All Clear All Refresh Lamp Control Auto Lamp Control vox i j i i d Fr MT J i ng WT Min a Apply Manual Lamp Control _ ra Sy 3 4 4 Ambient Light Reference o Lamp Vaue 0 Je An Info Grid showing several basic data items appears 1 Maintenance Allows the Maintenance Control function for all input sources 2 Lamp Control Automatically adjusts the backlight of the selected display at a specified time The Manual Lamp Control automatically turns off if you adjust using the Auto Lamp Control Allows you to adjust the backlight of th
118. t Lemp Control Help SAMSUNG MGT Faulty Device 0 Select All Clear All Refresh Afo O so Pe B L 2 PC BNC DVI OP m Sn ee E Idle Je Info Grid shows some basic information necessary to Image Size Control 1 El Power Status Shows the power status of the current display 2 Image Size Shows the current Image Size of the display in use 3 Input Info Grid displays only the displays whose Input Source is PC BNC DVI and DP 4 PC Source Click Image Size in the main menu to display the PC BNC DVI and DP tabs The Image Size Control button controls Image Size available for PC BNC DVI and DP 5 Video Source Click the Video Source tab to control Image Size for respective Input Source k The Input source of Magicl nfo works only on Magicl nfo model k The Input source of TV works only on TV model k Image Size Control is available only for the displays for which power status is ON k DP may not be supported depending on the product EG I mage Size TV AV S Video Component DVI HDCP HDMI 1 HDMI 2 DTV 1 Click Image Size of the main icons and the Image Size control screen appears Multiple Display Control File Add a Dewice Remote Control SefetyLock Faul Device Alet Lamp Control Help Pr Faulty Device 0 Select All Clear All Refresh Idle O Video Source TV AV 5 Video Component HOMI1 HOMI2 OTY Amage Size Auto Wide 16 39 d Wide Zoom Zoom 3 d Toom 1
119. te Specifications Normal Op Power sav eration ing mode On 177 Watts 110 Watts Blinking 5 Watts 2 Watts Power off Amber 5 Watts 1 Watts Power off Power Swich Off 0 Watts 0 Watts e The actual power consumption may be different from the indicated power consumption above if the system conditions or settings are changed e To stop any power consumption turn off the switch or disconnect the power cable on the back Be sure to disconnect the power if you intend to stay away from home for many hours e Ifyou connect a network box sold separately the product will no longer be in compliance with Energy Star 5 0 specifications Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes the screen will be adjusted automatically However if the signal differs the screen may go blank while the power LED is on Refer to the video card manual and adjusts the screen as follows Display Mode IBM 640 x 350 IBM 640 x 480 IBM 720 x 400 MAC 640 x 480 MAC 832 x 624 MAC 1152 x 870 VESA 640 x 480 VESA 640 x 480 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 VESA 800 x 600 kHz 31 469 31 469 31 469 35 000 49 726 68 681 37 861 37 500 35 156 37 879 48 077 46 875 70 086 59 940 70 087 66 667 74 551 75 062 72 809 75 000 56 250 60 317 72 188 75 000 MHz 25 175 25 175 28 322 30 240 57 284 100 000 31 50
120. ters the product disconnect the power cord and contact a Service Center e Otherwise this may result in electric shock or fire L When using a fixed screen for a long time an afterimage or stain may occur e If you are not using your product for a long period of time put it into sleep mode or use a moving screen saver Safety Instructions 3 Set a resolution and frequency appropriate to the product e Otherwise your eyesight may be damaged L When using headphones or earphones do not turn the volume too high e Having the sound too loud may damage your hearing L To avoid eyestrain do not sit too close to the product J Take a rest for at least five 5 minutes after using the monitor for one 1 hour This reduces eye fatigue O Do not install it in an unstable location such as an unstable rack or uneven surface or a location exposed to vibrations e Otherwise it may fall and cause personal injury and or damage the product e Ifyou use the product in a location exposed to vibrations it may damage the product and result in fire IL When moving the product turn the power off and disconnect the power plug antenna cable and all the cables connected to the product e Otherwise it may result in electric shock or fire 3 Ensure that children do not hang onto the product or climb up onto the product e The product may fall and cause personal injury or death L If you do not use the product for a
121. the Connecting a Computer Check the volume level The sound level is too low Check the volume level If the volume is still too low after turning the control to its maximum check the volume control on the computer sound card or software Program The sound is too high or too low Adjusts the Treble and Bass to the appropriate levels Problems related to the Remote Control Note Problems related to the remote control and their solutions are listed Q gt 5 5 The remote control buttons do not respond Check the polarities of the batteries Check if the batteries are empty Check if the power is on Check if the power cord is securely connected Q amp A Troubleshooting A Checkifa special fluorescent or neon lamp is on in the vicinity Q How can I change the frequency A The frequency can be changed by reconfiguring the video card Note That video card support can vary depending on the version of the driver used Refer to the computer or the video card manual for details Q How can adjust the resolution A Windows XP Set the resolution in the Control Panel gt Appearance and Themes gt Display gt Set tings A Windows ME 2000 Set the resolution in the Control Panel Display Settings Contact the video card manufacturer for details Q How can set the Power Saving function A Windows XP Control Panel Appearance and Themes Display Screen Saver Set the functi
122. the displayed IDs using the Select or Clear button All of the monitors can be selected or deselected Selects Select or deselects Clear LFD IDs displayed by configuring 7 and 8 This searches for monitors The maximum number is indicated in the Max LFD Id field Select a display from Display Selection Use Grid to view brief information on selected display Use Control Tools to control displays Switches the OSD function On Off May not be supported depending on the product lt Note gt The remote control Enable Disable function operates whether or not the power is On Off and this applies to all displays connected to the MDC However regardless of the status at the time the MDC is shut down the remote control signal receiving function of all displays is initialized to Enable when the MDC is closed Port Selection BA Multiple Display Control Ka File Remote Control Safety Lock Pon Selection Lamp Control Options Help SAMSUNG OIGITali gt Idle Refresh Power On Power Off Volume 10 eS a aes ae 1o Lamp TerpSuns BrRSoser Fan Covent Tene OSD Display not oh Ga Source OSD OOO O i Not Optimum Mode OSD Ds ee ae et aes ee ae Bm maa Maintenance 1 The Multiple Display Control is originally set to COM1 If any port other than COM1 is used COM1 through COM4 can be selected in the Port Selection Menu If the exact port name that is connected to the LCD
123. the product The Input source of Magicl nfo works only on Magicl nfo model amp HDMI2 may not be supported depending on the product ii Setti ng Picture 1 Click Settings of the main icons and the Settings Control screen appears B Multiple Display Control File Add a Device Remote Control Setetylock FeultDewceAlet Lamp Conirol Help Faulty Devine U Select All Clear All Idle j lo lino E NG AT pe 5 Alo lo Av TV AV S Video Component HDMI HDMIZ DTV i gt 2 Contrast hl a a CHA al i Brighiness 6f ca nout Sour 4 Sharpness Pi i COT I Tan J Tint a Color lame 8 d Color Temp 10000K Brightness Sensor a 10 Dynamic Contrast Je Basic information required to adjust the Picture is displayed in the main menu Settings for the selected monitor will be displayed if one of the connected monitors is selected and the default settings will be displayed if all monitors are selected by clicking All and Select If a value is changed in this screen the current mode will automatically switch to custom mode 1 Picture Available only for TV AV S Video Component HDMI1 HDM12 DTV 2 Contrast Adjusts Contrast of the selected display 3 Brightness Adjusts Brightness of the selected display 4 Sharpness Adjusts Sharpness of the selected display 5 Color Adjusts Color of the selected display 6 Tint Adjusts Tint of the selected display Avai
124. trol and set 5 When connecting to the monitor fails it turns the function that transfers the result through an email on or off 6 Selects a Lamp adjustment mode 7 Select a display from Display Selection 8 All of the monitors can be selected or deselected 9 Use Control Tools to control displays 10 Switches the OSD function On Off May not be supported depending on the product lt Note gt The remote control Enable Disable function operates whether or not the power is On Off and this applies to all displays connected to the MDC However regardless of the status at the time the MDC is shut down the remote control signal receiving function of all displays is initialized to Enable when the MDC is closed Add a Device so Multiple Display Control ee kad Fie AddaDevice Remote Control SafetyLock Faut Device Alet Lemp Conrol Help sasawa oom Faulty Device D Idle Device IP Address Part Number Maintenance 1 Enter the IP address of the monitor to be connected and press the Add button to add the IP address If you click the OK button adding the monitor is completed System i gi 1 Click System in the main menu to open the system adjustment screen E Multiple Display Control 8g File Adda Device Remote Control _SafstyLock FautDevics Alert Lamp Cortal Hei anga ps NG L aulty Di Device Select All Clear All Refresh Idle Power Off Network
125. ty You can have an uneven picture quality on screen if the best picture quality is not provided for TFT LCD e Resolution 1366 x 768 e Vertical frequency refresh rate 60 Hz TFT LCD panels manufactured by using advanced semiconductor technology with a precision of 1ppm one millionth and above is used for this product But the pixels of RED GREEN BLUE and WHITE Color seem to be bright sometimes or some of black pixels could be seen This is not from bad quality and you can use it without any problems e For example the number of TFT LCD sub pixels contained in this product are 3 147 264 a When cleaning the monitor and the panel outside please apply a small amount of water to a soft cloth Rub softly when cleaning the LCD area If excessive force is applied you may stain it E3 If you are not satisfied with the picture quality you can get better quality of picture by performing the Auto Adjustment function in display screen that is appeared as window termination button is pressed If there s still noise after the automatic adjustment use the Fine Coarse adjustment function o When viewing a fixed screen for an extended period of time a residual image or blurriness may appear Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time PRODUCT INFORMATION Image Retention Free 5 What is Image Retention Image retention may not oc
126. ut source for the selected Display to DP 12 Channel Channel arrow appears when the Input Source is TV HDMI2 may not be supported depending on the product DP may not be supported depending on the product k TV Source can be selected only in products with TV and controlling channels is allowed only when Input Source is TV k The Input Source Control feature is available only for the displays whose power status is ON KO I mage Size PC BNC DVI DP 1 Click Image Size of the main icons and the Image Size control screen appears Multiple Display Control File Remote Control Safety Lock Port Selection Lamp Control Options Help lala Refresh PC m PC BNC DVI DP 16 9 BE Ye Info Grid shows some basic information necessary to Image Size Control 1 El Power Status Shows the power status of the current display 2 Image Size Shows the current Image Size of the display in use 3 Input Info Grid displays only the displays whose Input Source is PC BNC DVI and DP 4 PC Source Click Image Size in the main menu to display the PC BNC DVI and DP tabs The Image Size Control button controls Image Size available for PC BNC DVI and DP 5 Video Source Using the Image Size adjustment button you can adjust the Image Size to a value available in the PC BNC DVI and DP amp DP may not be supported depending on the product The Input source of Magicl nfo works only
127. y Settings lt 2 Maintenance kai 1 Select or clear all the added devices or refresh or delete selected devices 3 2 The IP Address ID Ethernet or Serial Mac Address and connection status of the connected monitor is displayed It can automatically check whether DHCP IP is set and then set the IP address 4 It can automatically or manually set and then apply the IP Address Subnet and Gateway of the selected monitor lt Input Source Click Input Source of the main icons and the Input Source control screen appears Selects displays you want to adjust using the Select All button or checkboxes e TV Mode Multiple Display Control Fie AddaDewce Remote Control Setety Lock Fault Device Alert Lamp Control Select Al PC Mode ha Multiple Display Control File Add a Device Remote Control Select All Clear All LI Clear An Refresh Refresh b ja p jja laha Xm 5 ESIKANOGSIES i 7 k i en A k Lock Fault Device Alert Lamp Control a F Tag p SAMSUNG DIGITA Faulty Device U Help ldle Choose Input Source AW Ea LT g 4 Component 8 i Meghan 9 HOMI pil HIME Oo oF Fe Be Help SAMSUNG OWT Faulty Device 0 Idle Choose Input Source PC av 6 SVideo 4 1 i h F Component 19 HOMI o 1
128. y Control MDC Syste Introduction ai SELLI a Ethernet Ethernet RS 232 In RS 232C In RS 232C Oul RS 232C Out RS 232C Out Unlike the previous method which used the serial data communication specifications RS 232C an Ethernet function has been added Connect the first display device and the PC by entering the IP address To connect to another display device use an RS 232C serial cable Refer to the figure above Main Screen Click Start gt Program gt Samsung gt MDC System to start the program Select a set to see the volume of the selected set within the slider Multiple KO py kanaba 3 i OE ak E Sore sm Faulty Device i m Select All Clear All Refresh Idle a i aor r4 TG GG KA Dainai Rone om Volume 74 oo pa 4 E OSD Display Source O50 Not Optimum Mode OSD No Signal OSD MDC OSD 40 Gb Main Icons O Lamp Control 2 Add a Device GA Display Selection GD Remote Control O Info Grid O Safety Lock O Control Tools O Fault Device Alert D OSD Display 1 Use the main icons to switch into each screen 2 You can add a device by entering the IP address configured on the monitor 3 Allows you to enable or disable the remote control signal receiving function of the display unit 4 Set the Safety Lock function When setting the Lock function you can only operate power and lock buttons on the remote con
129. you deselect a single display or all displays the default value 10 will be restored 3 EB Mute On Off Turns on off the Mute function of the selected display When selecting one set at a time turn on the Mute function for the selected set The Mute function is disabled automatically when you adjust the volume level The values return to the default settings when you undo the selections or choose Select All amp The Volume Control and Mute features are available only for the displays whose power status is ON 3 Selects whether to display the menu screen using the OSD Display menu Multiple Display Control Fila Remote Control Safoly Lock Port Selection Lamp Control Options Powor On a Power ON Volume 10 4 O5D Display 4 Y Source OSD aa 2 Not Optimum Mode OSD 3 No Signal OSD gt MDC OSD 4 1 Source OSD Sets whether the Source OSD will be displayed to indicate when the Source is changed 2 Not Optimum Mode OSD Sets whether the Optinum Mode OSD will be displayed to indicate if the current mode is not supported 3 No Signal OSD Sets whether the No Signal OSD will be displayed to indicate when there is no signal 4 MDC OSD Sets whether the MDC OSD will be displayed to indicate when the settings are changed using the MDC aps I nput Source 1 Click Input Source of the main icons and the Input Source control screen appears Selects displays you want to adjust using the S

Samsung 320MXN-3

Contents

Download Pdf Manuals

Related Search

Related Contents