Energy Sistem Energy Linnker 4440
Contents
1. SSS tooth Bluetooth Stereo Headset Bluetooth Stereo Adapter English Function of Buttons b Turning on or off Pairing Answer Ending Reject play pause stop Volume up Redial Volume down Voice Dialing PP O Forward 4 Backward Q Microphone Charging Port Q 3 5mm audio port Clip 3 5mm audio jack moona amp Status Button Duration LED Pattern Stereo Headset Stereo Adapter Power On U Long 2 3 seconds Blue Blinking Power Off W Long 3 4 seconds Red Off Enter Pairing b s le a Blue Red Blinking Pairing Successfully Standby Blue Blinking Answer Ending Calls W Short Redial Long 2 seconds Voice Dial Long 2 seconds Reject W Long 3 seconds Play Pause Stop O Short 2 second Volume Up Down Short 1 second Forward Backward lt lt gt gt Short 1 second Low Battery Red Blinking Charging 4hosws o Red Fully Charged Red Off 1 Charging the battery Plug the travel charger into the AC outlet and then connect the charger into the DC input of the headset and adapter The red indicator will light on When the battery is full the red indicator will be off disconnect the power adapter When the battery is new it is not fully charged It takes 4 hours to fully charge the battery Afterwards it will take nearly 3 hours to fully charge2. to repeat STEP 3 1 3 to successfully complete the pairing 4 Adjusting the volume of the headset for listening to music a Press the button of the headset to increase the listening volume of the headset b Press the button to decrease the listening volume of the headset Note You want to listen to music after initial pairing just adjust the volume from your headset and audio device ipod MP3 CD player etc together and turn on both devices They will automatically connect and listen the music 4 an P K 3 2 Use with mobile phone Before start pairing please refer to the manual of your mobile phone and read through the pairing chapter 1 Turning on and pairing a Turn on the headset power press the button of the headset for 4 seconds till the blue and red indicators begin to flash alternatively The headset is now in pairing mode b Turn on your Bluetooth mobile phone follow the manual of your mobile phone to activate Bluetooth device pairing process Your mobile phone will found the stereo headset device in the devices list Select it for pairing c The mobile phone display will prompt you for pairing pin code during pairing please enter 0000 to successfully complete the pairing process d When the pairing process is successfully completed the blue indicator will flash The headset is now in standby mode and will connect your mobile p
3. econds to redial the call you just ended The availability of this function depends on the design of the mobile phone you use Please refer to the manual of your mobile phone d Rejecting a call When there is a call in session you can press the button for 3 seconds to reject a call 3 3 Use with music player and mobile phone at the same time a The stereo headset needs to be paired and connected with both devices b When a phone call comes in while listening to music the music will stop and you will hear ring tones on the headset press the the button to answer the call b Press the button for at least one second to terminate the call and the music will automatically resume 3 4 Use with Bluetooth PC or PDA devices 1 Connect with PC a Install Bluetooth driver and plug the Bluetooth USB dongle to a free USB port on your computer b Please repeat STEP 2 2 1 a to in pairing mode c Please click to search the service of Bluetooth stereo headset device in the Bluetooth driver d Your computer display will prompt you for pairing pin code during pairing please enter 0000 to successfully complete the pairing process Then connect Bluetooth stereo headset and your computer Note If need to chat on VoIP please connect headset service before launching VoIP software such as Skype MSN and Messenger etc 2 Adjusting the volume of the headset Please repeat STEP 2 1 4 to adjust the volume of
4. hone automatically e Now you can put on the headset to play music When the headset is receiving a phone call ring tones will be heard on the headset Note a If no pairing is possible over a period of time Aprox 1 minute the pairing process will be stopped You have to repeat STEP 2 2 1 to successfully complete the pairing b your Bluetooth mobile phone have to support A2DP and AVRCP profiles and can play music function 2 Adjusting the volume of the headset Please repeat STEP 3 1 4 to adjust the volume of the headset 3 Making calls Dial the phone number on you mobile phone as you normally do The sound will be transmitted to the headset a Receiving or ending calls When the headset is paired with your phone and when there is an incoming call you will hear a musical beep Then press the button W to receive the call When there is a call in session you can press the button U to end the call Note Due to the different design of some mobile phones an auto disconnect may happen even when the headset is powered on b Voice dialing Press the button and hold 2 seconds After hearing a beep sound say the name of the person you recorded on your phone The availability of this function depends on the design of the mobile phone you use Please refer to the manual of your mobile phone for the voice dialing function c Redialing the call After ending the call you can press the button and hold 2 s
5. the battery 2 1 Wearing the headset Hold both sides of the headset Ear hook the headset from the back of head Gently adjust headset position 2 Use with earpieces or home audio speakers optional a Plug the earpieces 3 5mm audio jack into the 3 5 mm audio port b Plug the home audio speakers 3 5mm audio jack into the 3 5mm audio port 3 1 Use with audio devices 1 Turning on or off a Press the button D for 2 3 seconds The blue indicator will begin to flash The headset and adapter are now powered on b Press the button D for 3 4 seconds The red indicator will begin to flash Now the headset and adapter are turned off 2 Plug the 3 5mm audio jack into the 3 5mm audio port device Note To use stereo adapter with DVD TV or Hi Fi system etc please use the AV cable to audio device 3 Pairing a Press the button D of the headset and adapter for 4 seconds till the blue and red indicators begin to flash alternatively The headset is now in pairing mode and it will connect to the stereo adapter automatic If the blue and red indicators do not flash alternatively press the button W again b When the pairing process is successfully completed the blue indicator will flash The headset is now in standby mode and will connect the stereo adapter automatically Note If no pairing is possible over a period of time Aprox 1 minute the pairing process will be stopped You have
6. the headset Note your Bluetooth dongles or devices have to support A2DP and AVRCP profiles and can play music function
Download Pdf Manuals
Related Search