Gigabyte Sumo 5112
Contents
1. Incorrect connector 02 English provide users with the most optimal solution for thermal dissipation x Content 1 Components Introduction 1 1 Casing s Internal Structure 1 2 Casing s Panel Structure 1 3 Removal of Side and Front Panels 2 Features 3 Specifications 4 Installation Instruction 4 1 Installation of Power Supply 4 2 Installation of Motherboard 4 3 Installation of Add On card 4 4 Installation of Front Multi Media I O Ports 4 5 Connection of Fan Power Cable 4 6 Installation of 5 25 Front Device Bay 4 7 Installation of 3 5 Front Device Bay 4 8 Installation of 3 5 Internal Device Bay 4 9 Application of Removable Dual Directional HDD Rack 4 10 Installation of 2 5 Enclosure 4 11 Application of DIY inter changeable LED lighting 4 12 Application of Security locks 4 13 Application of Foot Support 4 14 Application of Liquid Cooling System 4 15 Recommended GIGABYTE Thermal Solution products 04 04 05 05 06 07 08 08 08 08 09 10 10 10 10 11 11 11 11 12 12 12 English 03 1 Components Introduction 1 1 Casing s Internal Structure Power Supply Bay 5 25 Front Device Bay Dual Rear fans Motherboard tray and PCI Slot panel 3 5 Front Device Bay PCI Tool Free Fastener 3 5 Internal Device Bay Piping Outlets Front intake Fan Foot Support m Accessory BOX Refer to the figures below for the attachments in the accessory box Motherboard Securing Pow2. HD or AC 97 2 Basic casing power switch control cable kit Required Tools None Please refer to the instructions supplied by the motherboard manufacturer and make sure the correct type of connector is nore used prior to installation 1 1 x eSATA 2 x USB 2 0 1 x IEEE 1394 and 1 x Audio Set HD or AC 97 4 4 1 Insert the eSATA connector into the corresponding socket on the motherboard 4 4 2 Insert the USB 2 0 connectors into the corresponding sockets on the motherboard please refer to the motherboard user manual for further information USB 2 0 connector Pin Definition Pin Definition 2 10 1 Power 6 USB Dy 1 FILT 9 2 Power 7 GND 3 USB Dx 8 GND 4 USBDy 9 5 USB Dx 10 USB Over current 4 4 3 Insert the IEEE 1394 connector into the corresponding socket on the motherboard IEEE 1394 connector A Pin Definition Pin Definition 2 10 1 TPA 6 TPB 1 APERE 9 2 TPA 7 3 GND 8 12V 4 GND 9 12V 5 TPB 10 GND IEEE 1394 connector B Pin Definition Pin Definition 2 10 1 TPA 6 TPB IEEE 1394 connector C Definition Pin Definition 1 LE 9 2 TPA 7 12V 2 16 12V 9 12V eee SID se 4 GND 9 TPA 11 TPA1 5 TPB 10 GND TPA 12 TPA1 GND 13 GND GND 14 TPB 15 TPB1 TPB 16 TPB1 4 4 4 Insert the Audio connector into the corresponding socket on the motherboard HD AUDIO Pin Definition Pin Defini
3. Installation complete 4 7 Installation of 3 5 Front Device Bay The Installation of the 3 5 front device is the same as the installation of the 5 25 front devices Please refer to step 4 6 Required parts none 4 8 Installation of 3 5 Internal Device Bay This chassis provides a removable dual directional HDD rack to accommodate up to 5 hard disc drives Required Tools Thumbscrews 4 per hard disc drive Slide the HDD into the rack and secure the HDD with the thumbscrews English 4 9 Application of Removable Dual Directional HDD Rack This chassis includes a removable dual directional HDD rack for preferred installation direction and optimal heat dissipation Required Tools None Remove the thumbscrew Unlock tool free fastener of the removable HDD rack by that secures the removable pushing it downwards HDD rack Change the HDD rack directional alternating fastener on top ofthe rack and align the arrows for desired direction Dual Direction Only 4 10 Installation of 2 5 Enclosure 4 10 1 Connect the 4 pin power cable to the 5 25 front device housing 4 pin power port 4 10 2 Connect the SATA cable from the e SATA side to the SATA port on the motherboard 4 10 3 Insert the 2 5 HDD mobile enclosure into the 5 25 front device housing and push it until the 2 5 HDD mobile enclosure is firmly secured 4 10 4 Press the eject button and remove the 2 5 HDD mobile enclosure from the 5 25
4. and screw driver 4 2 1 According to the motherboard s specifications select the proper screw points Screw in the copper stand offs into the corresponding points on the motherboard 4 2 2 Change the motherboard I O bracket on the rear panel supplied by the motherboard manufacturer 4 2 3 Secure the motherboard with the motherboard screws refer to your motherboard manual to check what type of motherboard you have Motherboard Code on tray Securing screw E ATX E1 E12 11 CEB E1 E8 ATX Micro ATX Copper stand off 4 3 Installation of Add On card English This chassis supports tool free installation of add on cards 10 5 length or lower e g graphics cards sound cards and etc Required Tools None 4 3 1 Unlock the PCI slot clamp 4 3 2 Remove the internally attached PCI slot blanking plate 4 3 3 Insert the add on card into the expansion slot with care 4 3 4 Secure the PCI clamp i al I A n VON amg UX jen nell I 1 ale a a 5 NE SD 4 4 Installation of Front Multi Media 1 0 Ports Incorrect connection of sockets can cause the motherboard to malfunction or completely destroy the motherboard Please observe the installation instructions in the manual carefully as incorrect installations or connection causing CAUTION faults will void your warranty The top panel includes 1 1x eSATA 2 x USB 2 0 1 x IEEE 1394 and 1 x Audio Set
5. SUMO 5112 GZ FADA51 CJB Black English User s Manual SUMO Sile Thank you for purchasing a GIGABYTE Chassis GIGABYTE is dedicated to the integration of water air cooling chassis solutions to For further information and specifications of the SUMO series please visit GIGABYTE website http www gigabyte com tw The following is not covered by warranty Using the product incorrectly or in a manner other than its designed purpose Nonobservance of its proper operation as provided in documentation Malfunction due to interference from other devices Unapproved modification of the product Consequential damage to other object due to the product s fault Malfunction arising from natural hazards e g earthquake lightning fire and floods Warranty void if label has been removed or tampered with The devices inside including power supply hard disk CD ROM drive motherboard ventilator etc are not detached from the casing prior to transportation of the computer system resulting in damage to the casing or other computer related devices 9 Any loss damage caused by failure to follow the installation process with in the user manual NQDQUSWN installation may possibly burn out the motherboard and other components Be sure to observe the instructions in the installation CAUTION Manual A Failure to wear gloves during installation of computer products may cause bodily harm or damage to your devices
6. er Supply Securing 3 5 Device Thumbscrews Screw x 12 screw x 4 x8 Blue Led 2 5 HDD mobile enclo protective carry bag USB Y Cable sure Wire Clamp x 2 Key Cable tie x 2 04 English m Cable Kit Refer to the figures below for the cable connectors eSATA IEEE1394 Multi connectors Fan 3 Pin Connector Power LED 4 pin Connector Power SW Reset SW Speaker Connector 1 2 Casing s Panel Structure Red Led Disc Storage 2 5 enclosure docking Transparent side panel Ventilated mesh side panel Power Switch Multi Media I O port 1 3 Removal of Side and Front Panels 1 3 1 To remove side panels 1 3 1a Remove the 6 thumb screws at the rear of the side panel and detach the side panels 1 3 2 To remove front panel 1 3 2a Remove the left and right side panels see step 1 3 1 on page 5 release the 6 clamps that hold the front panel onto the chassis gt English 05 06 2 Features High quality Design GIGABYTE top class Full tower thermal solution casing Aluminum 3D front panel design with hair line brush anodized finishing Illuminated and atmospherically soothing backlight for a post modern classy impression Complete I O Support Complete Top panel multi media support includes 1 x eSATA 2 x USB 2 0 1 x IEEE1394 1 x Audio Set HD amp AC 97 Full Support of GIGABYTE thermal solution LCS and Air cooling products lines Supports E ATX CEB ATX Micro ATX motherboards Integrat
7. front device housing 4 11 Application of DIY inter changeable LED lighting 4 11 1 Remove front panel following instruction in 1 3 4 11 2 Detach the LED holder by simply squeeze the securing hook at top and bottom softly 4 11 3 Unsecure the existing LED amp separate the wire from LED holder from open gap then reinstall blue light LED amp wire 4 12 Application of Security locks This chassis provides one security lock including side panel lock Insert the key and turn 90 to lock or unlock English 11 12 4 13 Application of Foot Support This chassis is supplied with foot supports for ensureing the caseing is firmly seated on the holding surface Swivel these four feet 90 to change their position when moving or laying down the case please swivel the foot support to the closed position to prevent bending the foot an eg N TE support 4 14 Application of Liquid Cooling System This chassis fully supports GIGABYTE 3D Galaxy series liquid cooling system also supports most of the liquid cooling systems currently available While installing the liquid cooling system please refer to it s manual in advance 4 15 Recommended GIGABYTE Thermal Solution products The following GIGABYTE thermal solution products are recommended for use with this product English
8. ion of Cooling Technology Industry leading dual rear 12cm silent blue LED fan Large air volume with low noise Unique ventilated mesh transparent side panel design Convenience of assembly Scratch resistant processing that ensures safety during assembly Tool free installation design Side panel with one hand operation for easy disassembly Sufficient spacing for easy 10 5 VGA card installations English 3 Specifications O ports jp pmpmqgmpmpqmpqgepmepqp GZ FADA51 CJB 1 x eSATA 2 x USB 2 0 1 x IEEE1394 1 x Audio Set AC 97 HD English 07 08 4 Installation Instruction S amp S Please follow the reference sections in order for installation NOTE 4 1 Installation of Power Supply To facilitate the installation it is recommended to set the chassis upright on the table Required parts power supply securing screws x 4 4 1 1 Remove side panel see step 1 3 10n page 5 4 1 2 Place the power supply unit into the case 4 1 3 Secure the power supply with the 4 securing screws 4 1 4 When using large power supply unit please disassemble the cross bar by loosening screws Fasten the screws to secure the cross bar after the power supply is installed 4 2 Installation of Motherboard This chassis supports E ATX CEB ATX Micro ATX motherboards Please confirm the dimensions and fixing points of the motherboard prior to installation Required parts Copper stand offs Motherboard screws
9. tion 9 1 1 MIC2L 6 FSENSE1 10 SULL 2 2 GND 7 FAUDIO JD 3 MIC2R 8 4 5 ACZ_DET 9 LINE2_L LINE2_R 10 FSENSE2 AC 97 Pin Definition Definition 9 1 1 MIC NC 10 SULL 2 2 GND 7 NC 3 MIC Power 8 4 NC 9 Line Out L 5 Line Out R 10 NC English 09 10 2 Basic casing power switch control cable kit Follow the connectors list below for installation see figure below Connector Color Power LED Green Wite Orange White 4 5 Connection of Fan Power Cable This chassis has 1 x 12cm silent cooling fan at the front and 2 x 12 cm silent blue LED fans at the rear There are internal connectors that connect the front and rear fans making it into a single 3 pin power connector Required Tools None 4 5 1 Insert the 3 pin connector into the system fan power connector on the motherboard Different Motherboards have different installation areas specifications screw holes and connectors Please read the motherboard user manual supplied by the CAUTION motherboard manufacturer e O O 4 6 installation of 5 25 Front Device Bay 4 6 1 Open the front panel door and side panel remove the plastic bezel and EMI plate through the inside of the chassis 4 6 2 Slide in the 5 25 device through the front panel to align it with the front panel bezels 4 6 3 Secure the 5 25 device with the internal latch Refer to the figure for installation procedure 4 6 4
Download Pdf Manuals
Related Search