JBL GTO5355 audio amplifier
Contents
1. JBL GTO5355 OWNER S MANUAL BEDIENUNGS ANLEITUNG MODE D EMPLOI MANUAL DE USO HANDLEIDING MANUALE UTENTE ANV NDAR HANDBOK BRUGSVEJLEDNING OMISTAJAN K SIKIRJA PODRECZNIK UZYTKOWNIKA PYKOBOACTBO MOJIB3OBATEJIA WwoOWWwW WY E 0 ADDED Cimi DITE mF ee a g FRONT FRONT FRONT UD gt sm GT05355 CAR AUDIO POWER AMPLIFIER OWNER S MANUAL Installation Warnings and Tips e Disconnect the negative lead from your vehicle s battery e At the installation sites locate and make a note of all fuel lines hydraulic brake lines vacuum lines and electrical wiring Use extreme caution when cutting or drilling in and around these areas Choose a safe mounting location away from moisture e Make sure there is sufficient air circulation at the mounting location for the amplifier to cool itself e Mount the amplifier using the supplied hardware Specifications e 55W RMS x 4 channels plus 225W RMS x 1 channel 4 ohms and lt 1 THD N e 75W RMS x 4 channels plus 360W RMS x 1 channel 2 ohms and lt 1 THD N e THD N 0 03 rated power 4 ohms e Signal to2. fuse holder and fuse 80A minimum within 18 inches of the battery Make sure the wire is not damaged or pinched during installation Install protective grommets when routing wires through the firewall or other sheet metal e GND Connect to the vehicle s chassis Refer to the picture below Factory Bolt Ring Connector Ground Wire y Star Washer Note Remove any paint below ring connector e REM Connect to the Remote Out lead from the source unit or to a source of switched 12V ACC Front Input Connectors RCA e Connect to the front RCA outputs from the source unit or signal processor Front Input Level Control e Used to match the front input level of the amplifier to the output level of the source unit e See for the adjustment procedure Q Front Crossover Frequency Control e 12dB octave crossover variable from 32Hz to 320Hz e See for the adjustment procedure Front Crossover Filter Selector e LPF Select for subwoofer s e Flat Select for full range speakers when no subwoofer will be used in the system e HPF Select for midrange speakers or full range speakers when a subwoofer is used in the system Power On LED e Illuminated when the amplifier is on Subwoofer Input Connector RCA e Connect to the subwoofer RCA outputs from the source unit or signal processor Rear Crossover Filter Selector e LPF Select for subwoofer s e Flat Select for full range speake
3. ith Variable Boost Q For woofers in tuned vented enclosures set the Frequency control to a value 10Hz below the enclosure s resonance tuned frequency e For woofers in sealed boxes set the control to any value you prefer between 30Hz and 50Hz e Set the Boost control according to your preference being careful not to apply enough boost to damage your woofer s EN DBO High Pass Filter Frequency control variable between 20Hz and 100Hz See above for appropriate settings EJ DBO Boost control provides up to 12dB of boost slightly above the high pass filter s frequency See above for appropriate settings Setting Input Level EN Turn all Input Level controls counterclockwise to 6V minimum E With a dynamic music track playing turn the head unit s volume control to the 3 4 position Turn Front Input Level control clockwise until the music is so loud that it no longer sounds clear distortion is present in the output 2 Turn Front Input Level control counterclock wise gradually just until the music sounds clear once again 3 Front Level input is now adjusted correctly a Adjust the Rear and Sub Input Level controls so that the level of the rear speakers and the level of the subwoofer are proportionate to the level of the front speakers according to your preference Setting the Crossover EN Crossover setting for 5 or larger full range speakers when no subwoofer is included in the system E Cross
4. mit tserkl rung ce Wir Harman Consumer Group Inc 2 route de Tours 72500 Ch teau du Loir Frankreich erkl ren in eigener Verantwortung dass das hier beschriebene Produkt folgenden Standards entspricht EN 55013 2001 A1 2003 l U 7 EN 55020 2002 A1 2003 fh Klaus Lebherz Harman Consumer Group Inc Ch teau du Loir Frankreich 8 07 Declaration of Conformity C We Harman Consumer Group Inc 2 route de Tours 72500 Ch teau du Loir France declare in own responsibility that the product described in this owner s manual is in compliance with technical standards EN 55013 2001 A1 2003 1 U EN 55020 2002 A1 2003 h YU F Klaus Lebherz Harman Consumer Group Inc Chateau du Loir France 8 07
5. noise ratio 85dB reference 1W into 4 ohms e Signal to noise ratio 104dB reference rated power into 4 ohms e Frequency response 10Hz 83kHz and 20Hz 250Hz Max power 660 watts CEA 2006A compliant Speaker Output Connectors e Connect the speakers to these terminals observing proper polarity e Five channel operation Connect the front left speaker to the Front L and L terminals and the front right speaker to the Front R and R terminals Repeat for the rear speakers using the Rear L and L terminals and the Rear R and R terminals Connect the subwoofer to the Sub and Sub terminals Four channel operation Connect the stereo speakers to the Front terminals as above Connect the single speaker into which the amplifier s rear channels will be bridged to the Rear R and Rear L terminals Connect the subwoofer to the Sub and Sub terminals e Three channel bridged operation Connect one speaker to the Front R and Front L terminals Connect the other speaker to the Rear R and Rear L terminals Connect the subwoofer to the Sub and Sub terminals e Minimum speaker impedance for stereo operation is 2 ohms Minimum speaker impedance for bridged operation is 4 ohms Minimum subwoofer impedance is 2 ohms Fuses e Replace only with same type and rating Power Input Connectors e 12V Connect to the positive terminal of the vehicle s battery 4 AWG wire is recommended Install an appropriate
6. over setting for full range speakers when a subwoofer is included in the system Crossover setting for subwoofers 2 Crossover setting for systems that include separate mid bass speakers driven by the rear channels with the BP switch set to BP Note Acceptable frequency ranges are indicated in gray 2 Remote Level Control The Remote Level Control if installed will allow you to adjust the level of bass while seated in the listening position This product is designed for mobile applications and is not intended for connection to the mains A valid serial number is required for warranty coverage Features specifications and appearance are subject to change without notice JBL www jbl com Harman Deutschland GmbH H nderstra e 1 74080 Heilbronn Telefon 07131 480 0 www jbl audio de O 2007 Harman International Industries Incorporated Alle Rechte vorbehalten JBL ist eine Marke von Harman International Industries Incorporated eingetragen in den Vereinigten Staaten und oder anderen L ndern Teile Nr GT053550M 8 07 Harman Consumer Group Inc 250 Crossways Park Drive Woodbury NY 11797 www jbl com 2007 Harman International Industries Incorporated All rights reserved JBL is a trademark of Harman International Industries Incorporated registered in the United States and or other countries x p Part No GT053550M 8 07 H A Harman International Company Konfor
7. rs when no subwoofer will be used in the system e HPF Select for midrange speakers or full range speakers when a subwoofer is used in the system Rear Crossover Frequency Control e 12dB octave crossover variable from 32Hz to 320Hz e See the adjustment procedure in Rear Input Level Control e Used to match the rear input of the amplifier to the output of the source unit e See D for adjustment procedures Rear Input Connectors RCA e Connect to rear RCA outputs from the source unit or signal processor EXT INT Switch e If the source unit has a subwoofer output and you have connected it to the SUB input set this switch to the EXT position Otherwise set it in the INT position Subwoofer Remote Level Control Connector Connect the Remote Level Control RLC here using the supplied RJ 11 cable B Subwoofer Level Control e Used to match the SUB input of the amplifier to the output of the source unit e See D for adjustment procedures amp Protect LED e Illuminated under any of the following fault conditions battery over under voltage short circuit in speaker wires amplifier is too hot amplifier s output circuit has failed DC voltage present in the amplifier s output Subwoofer Low Pass Filter Frequency Control e 12dB octave low pass filter variable from 20Hz to 200Hz e See the adjustment procedure in DBO Dynamic Bass Optimization Variable Subsonic High Pass Filter W
Download Pdf Manuals
Related Search