Hoover U5468900 vacuum cleaner
Contents
1. Attach tool or wand to the hose G Attach second wand or tool to wand H by pushing it firmly onto the wand Twist wand or tool slightly to tighten or loosen the connection How to clean tools To clean the hose wipe off dirt with a cloth dampened in a mild deter gent Rinse with a damp cloth Cleaning tools may be washed in warm water with a detergent Rinse and air dry before using The indicator K will begin to show red as the filter bag fills with dirt There are three conditions that will cause the indicator to become com pletely red 1 If the bag is full change the bag 2 If very fine materials have been picked up clogging the bag pores change the bag 3 If there is a blockage in the nozzle hose tools or at the bag opening remove the blockage see Clearing blockages section Extra reach hose The extra reach hose provides an extra 20 foot reach for easier clean ing of stairs and hard to reach high places Follow the steps below for attaching and detaching the hose Attach hose Push ON OFF switch to OFF posi tion Remove regular hose from cleaner Align end of extra reach hose with projections 1 over slots J in dirt duct Familiarize yourself with these home maintenance tasks as proper use and care of your cleaner will ensure continued cleaning effectiveness Filter bag When to replace Check filter bag from time to time It is recommended that y2. align hinges of cover with slots on sides of tool storage area Push cover down to secure in place Cleaning tools Tools allow for cleaning surfaces above the floor and for reaching hard to clean areas The cleaner is ready for tool use when handle is in upright posi tion CAUTION Agitator continues to rotate while cleaner handle is in upright position Avoid tipping cleaner or setting it on furniture fringed area rugs or carpeted stairs during tool use Removing hose When using cleaning tools cleaner handle should be in the upright position Also turn cleaner OFF before disconnecting and con necting hose to hose tube A To use hose lift hose end as shown Lower cover B onto hose tube When you are finished cleaning with the tools be sure to lift cover from hose tube and reposition hose end into tube Select proper tool C Dusting brush may be used for carved furniture table tops books lamps lighting fixtures venetian blinds baseboards shutters and registers D Furniture nozzle may be used for upholstered furniture draperies mattresses clothing automobile interiors and carpeted stairs E Crevice tool may be used in tight spaces corners and along edges in such places as dresser drawers upholstered furniture stairs and baseboards F Wands are used to give extra length to your hose Use them with any of the above tools Continued gt 7 Attach wand and tools
3. matches or hot ashes Do not use to pick up flammable or combustible materials such as gasoline or fine wood sandings or use in areas where they may be present Avoid picking up hard sharp objects with the cleaner They may damage the cleaner and the bag Always turn off this appliance before connecting or disconnecting hose Do not use without dust bag or filters in place Change bag frequently when picking up very fine materials such as powder Use extra care when cleaning on stairs Do not put any object into openings Do not use with any opening blocked keep free of dust lint hair or anything that may reduce air flow Do not pull or carry by cord use cord as a handle close door on cord or pull cord around sharp edges or corners Do not run appliance over cord Keep cord away from heated surfaces Always disconnect cord from electrical outlet before servicing the cleaner Unplug cleaner when not in use Turn off all controls before unplugging Do not unplug by pulling on cord To unplug grasp the plug not the cord Never handle plug or appliance with wet hands The use of an extension cord is not recommended Do not use with damaged cord or plug If appliance is not working as it should has been dropped damaged left outdoors or dropped into water take it to a Dever Factory Service Center or Authorized Hoover Warranty Service Dealer Use vacuum cleaner only for its intended use as describ
4. seconds the red light will go off and the green light will come on Cleaning may then begin The green light will remain on throughout cleaning except when the detector senses that a larger amount of dirt is being picked up then the red light will come on When the red light is on you should take additional cleaning strokes in the area until it changes to green eThe red light may seldom come on during cleaning This means that your cleaner is picking up primarily fine surface dust and lint which the system may not detect or that the carpet is generally clean To increase the feature s sensitivity to dirt set the switch B to the Hi position eAt other times the red light may stay on for a considerable amount of Handle position For ease in sliding knob the handle should be in the upright position C The nozzle will not move into the adjusted position until the cleaner handle is lowered to the operating position D contains a high level of dirt which is being removed by the cleaner To decrease the feature s sensitivity to dirt set the switch to the Reg Regular position Settings For maximum cleaning perfor mance the following carpet height settings are recommended e Lowest setting for all types of carpet Note If the cleaner is difficult to push slide knob to the next higher setting e Higher settings for very deep pile carpet where easier pushing effort is de
5. shown and lift off lens Belt replacement The belt on your Hoover cleaner causes the agitator to rotate and is important for the effective operation of the cleaner The belt is located under the bottom plate of the cleaner and should be checked from time to time to be sure it is in good condition When to replace Disconnect cleaner from electrical outlet To check belt remove bottom plate as shown in How to replace Replace belt if it is stretched cut or broken What to buy To assure effective operation use only genuine HOOVER belts with your cleaner When purchasing a new belt ask for HOOVER part No 38528033 belt package no 40201160 Installing new belt With lettering on outside of belt and positioned as shown in box on D slide new belt over motor pulley B 10 Installing bulb Pull old bulb straight out of socket Push new bulb straight into socket until locked in place Excessive force is not required How to replace Disconnect cleaner from electrical outlet Removing bottom plate Place handle in low position and turn cleaner over so bottom side is up Remove the 4 screws as shown with a Phillips screw driver Lift off bottom plate A Replacing agitator brush roll Insert agitator through belt and place belt in belt guide C on agita tor Should the agitator shield D be come dislodged while replacin
6. way Insert ends of dusting brush A crevice tool B into storage areas Secure furniture nozzle C in clip Close tool cover 1 Handle 4 Hose 5 Tool cover 6 Dusting brush 7 8 Crevice tool 9 10 Wands low positions ON OFF switch Plug cord into electrical outlet To turn cleaner ON push switch up To turn cleaner OFF push switch down The assembled cleaner will look like the drawing 2 ON OFF switch 3 Cord hooks wrap cord around hooks for storage The top hook can be rotated right or left for easy cord release Furniture nozzle Carrying handle 11 Final filter door 12 Handle release lever step on lever to lower handle to operating or 13 Edge groomers 14 Furniture guard helps prevent cleaner from marking furniture Remove switch lock A above ON OFF switch B by pulling it straight out Dispose of switch lock If switch lock has come off during assembly make sure switch is in OFF position down before plug ging cord into electrical outlet 15 Nozzle control knob slide knob to correct setting for height of carpet being cleaned 16 Headlight a 17 Embedded Dirt FINDER sensitivity switch 18 Dirt FINDER display 19 Check bag indicator 20 Stair cleaning handle located below lower edge of door 21 Bag door 22 Cord clip 23 Hose rack some models only Operate cleaner only at volt age specified on data plate on botto
7. WindTunnel by HOOVER Congratulations on your purchase fe This WindTunnel vacuum cleaner uses HOOVER HEPA Filtration Type Y filter bags This product was designed for easy assembly See page 3 www hoover com Owner s Manual ENGLISH gt pp 1 12 ESPANOL gt pag 13 20 FRAN AIS gt p 21 28 Review this manual before operating cleaner Fill in and retain The model and serial number are located on the bottom of the cleaner as shown For your personal records please enter the COMPLETE model and serial number in the spaces provided and retain this information Your cleaner is model and has serial number It is suggested that you attach your sales receipt to this owner s manual Verification of date of purchase may be required for warranty service of your HOOVER product Be sure to fill out and return the product registration card included with your cleaner Index Assembling Cleaner sseeeseese Carton Contents ssccsseseeesesseeeens Cleaner Descriptions HOW TOUSE wiccsesiscteteesecieceeresscticcerecevs Embedded Dirt FINDER Feature 6 Cleaning TOols ccseceecsseeseeeeee 7 8 If You Have a Problem cccsssseeeen 12 Important Safeguards seceeee 2 Lubrication cccccsiseccscecesteteeivesenetedterestens 11 Maintenance Authorized Service csseseee 11 Cleaning Filters c csscsseseeeeeens 9 Clearing Blockages
8. aner Make sure the green colored side of filter faces outward Close door Should you want to replace this fil ter ask for HOOVER part No 40110004 Do not operate cleaner without either the secondary or final filter in place Replacing bag door Reposition bag door by placing tabs on bottom of door into opening C Press top of door to snap securely shut Reattaching filter door The filter door is designed with a break away feature which allows it to snap free if it is pushed open too far To reattach align hinges C of cover with slots on sides of filter area Press door back into place Check agitator shield Because your cleaner picks up so well we strongly recommend you check for debris accumulation under the agitator shield each time you clean the filters Removing debris under the shield will help maintain your cleaner s excellent pick up and suction Remove debris as follows 1 Disconnect cleaner from electri cal outlet 2 Check for dirt accumulation by removing bottom plate Fig 3 10 removing agitator a _ 3 11 and lifting agitator shield Fig 3 13 3 Remove any debris and replace shield agitator and bottom plate Figs 3 13 to 3 15 Headlight replacement What to buy This cleaner uses a 12 volt wedge base type 912 bulb Hoover part No 27313101 Removing lens Disconnect cleaner from electrical outlet Using a screwdriver remove the two screws as
9. ed in the instructions pte ony attachments recommended by The Hoover Company others may cause azards Save these instructions 1 Assembling cleaner This cleaner was inspected and packaged carefully before being shipped from the factory If you should happen to need assistance during assembly or operation Visit us online at www hoover com to find the service outlet nearest you click on the Service button OR Call 1 800 944 9200 for an automated referral of authorized service outlet locations U S only OR Call 1 330 499 9499 to speak with a representative in our Consumer Response Center Carton contents Remove all parts from carton and identify each item shown Make sure all parts are located before disposing of packing A Handle section B Cleaner body C Hose rack D Hose cleaning tools and wands E Handle bolts and nuts packet in bag with owner s manual Note The white switch lock above the ON OFF switch aids in the assembly of your cleaner Assembly can be continued if the switch lock is missing However do not remove the switch lock until assembly is completed STEP 1 Attach rack and handle Open tool cover on handle section Attach hose rack to handle section Align hole on rack with circular tab A by fitting hooks B on rack over on handle slots C on handle section Continued gt 3 Remove bag door on cleaner body by pushing d
10. g the belt or the agitator reposition it as shown noting the placement of its belt guide E Replacing lens Reposition lens and secure with the two screws Removing belt Remove agitator brush roll and used belt Discard used belt Securing agitator Grasp Se ara firmly and fit it into osition by first sliding end opposite he belt into the rectangular slot F on side of cleaner Pull other side of agitator G into place Turn agitator making sure belt is not phen between agitator and agita or shield Replacing bottom plate Reposition bottom plate and 4 Phillips head screws Tighten screws securely The edge groomers When to replace The edge groomers located on both sides of the nozzle should be replaced when they appear worn What to buy When purchasing edge groomers ask for HOOVER part No 39511004 How to replace Disconnect cleaner from electrical outlet Remove bottom plate as described in The belt section Fig 3 10 Thermal protector An internal thermal protector has been designed into your cleaner to protect it from overheating When the thermal protector acti vates the cleaner will stop running If this happens proceed as follows 1 Turn the cleaner OFF and discon nect it from the electrical outlet 2 Check secondary and final filters for dirt accumulation 3 Refer to Clearing blockages section 4 When cleaner is unplugged and the motor c
11. ity of this E A based upon ASTM International Carpet Cleaning Effectiveness Testing ASTM Test F608 Other performance factors include Hose Power ASTM Test F558 Surface Litter Cleaning Hard Floor Cleaning Edge Cleaning Cleaning Width and Air Filtration 4 If you have a problem If a minor problem occurs it usually can be solved quite easily when the cause is found by using the check list below Problem Cleaner won t run Possible Cause Possible Solution e Not firmly plugged in Plug unit in firmly No voltage in wall plug Check fuse or breaker Blown fuse or tripped breaker Replace fuse or reset breaker Thermal protector activated Allow cleaner to cool for 30 minutes this will reset the thermal protector Problem Cleaner tools won t pick up Possible Cause Possible Solution Broken or worn belt Replace belt Agitator brush roll worn Replace brush roll Filter bag full Change filter bag Incorrect carpet height setting Move nozzle control knob to lower setting Blockage in air flow passage Clear blockage Problem Cleaner hard to push Possible Cause Possible Solution Incorrect carpet height setting Move carpet height control to a higher setting Problem Smoky burning smell detected Possible Cause Possible Solution Belt broken or stretched Replace agitator brush roll belt as described in Figs 3 10 through 3 15 in the Mai
12. m of cleaner This cleaner is intended for household use Cord clip To help keep the cord out of the way while vacuuming position cord in cord clip A located at rear of cleaner on hose rack Continued 5 gt 5 Transporting cleaner To move your cleaner from room to room put handle in upright position tilt cleaner back on rear wheels and push forward Carrying cleaner The cleaner can also be moved by using the carrying handle Handle positions The handle of your cleaner has three positions upright for storage and when using cleaning tools operating position for general operation on carpet and floors low for reaching under low furniture Step on handle release lever to lower handle time This means that the carpet come on when the cleaner is first Embedded DirtFINDER feature some models only With red and green lights A the Dirt FINDER system alerts the user to areas of carpet that may need more cleaning attention It is able to sense when larger amounts of dirt particles especially embedded dirt are removed To let you know that the DirtFINDER feature is ready the red light will Carpet height adjustment The cleaning of carpet and rugs takes place at the nozzle A When it is necessary to raise and lower the nozzle for various carpet pile heights slide the nozzle control knob B to the desired setting 6 turned on After a few
13. ntenance section 12 Clearing blockages Disconnect cleaner from electrical outlet Low suction or pick up may be due to a blockage in the system Refer to the following steps to check for blockages continuing with each step until the blockage is found 1 Check fullness of filter bag change if needed Checking airflow path 2 Plug cleaner in and turn ON Check for suction at end of hose A a If there is suction continue with step 3 b If there is no suction check for blockage in hose and dirt tube as follows 1 Disconnect hose from dirt duct C by reversing procedure for Attach hose on p 4 Figs 1 11 and 1 12 2 Clear out hose 3 Look into C and remove blockage 3 Check connection at hose tube B remove any blockage Checking under bottom plate 4 Turn cleaner OFF and unplug 5 Remove bottom plate belt and agitator see The belt section Look into opening D for blockages and remove 6 Remove agitator shield see Fig 3 13 and remove any loose debris which may have accumulated under it Full One Year Warranty Domestic Use Your HOOVER appliance is warranted in normal household use in accordance with the Owner s Manual against original defects in material and workmanship for a period of one full year from date of purchase This warranty provides at no cost to you all labor and parts to place this appliance in correct operating con dition du
14. ools for 30 minutes the thermal protector automatically resets and cleaning may continue If the thermal protector continues to activate after following the above steps your cleaner may need servic ing see Service section The agitator brush roll When to replace When agitator brushes are worn the agitator should be replaced To check condition of brushes dis connect cleaner from electrical outlet Move edge of a card across bottom plate while turning agitator To maintain cleaning effectiveness replace agitator if brushes do not touch card What to buy Your cleaner requires either a 13 or 15 agitator When purchasing a new agitator ask for one of the fol lowing 13 HOOVER part No 48414110 15 HOOVER part No 48414115 Installing groomers Lift off both old edge groomers and slide new edge groomers into posi tion as shown Reposition bottom plate and secure with 4 Phillips head screws Service To obtain approved HOOVER service and genuine HOOVER parts locate the nearest Hoover Factory Service Center or Authorized Hoover Warranty Service Dealer Depot b e checking the Yellow Pages under Vacuum Cleaners House hold OR e checking the list of Factory Service Centers provided with this cleaner OR e checking the Service section of The Hoover Company on line at www hoover com OR e calling 1 800 944 9200 for an automated referral of authorized ser vice ou
15. ou change the filter bag before debris reaches the bottom of the bag collar If more dirt than this accumulates your cleaner will not operate effectively Note All new carpet has loose fibers which can fill the bag quick ly while vacuuming This type of debris does not activate the Check Bag indicator available on some models So if you are using the cleaner on new carpet be sure to change the filter bag often even if you have a Check Bag indicator and it does not show red CAUTION Very fine materials such as face powder or corn starch may seal the filter bag and may cause it to burst even though it is only partially full of dirt When cleaner is used to remove material of this nature change fil ter bag often Slide hose into J and twist hose to lock it into place To detach hose reverse proce dure Attach wands or tools to the other end of hose Available at additional cost if not included with your cleaner Where to buy Filter bags may be purchased from your Authorized Hoover Dealer Leading Retailers Hoover Factory Service Centers or through The Hoover Company on line at www hoover com What to buy To assure cleaning effectiveness use only Genuine HOOVER HEPA Filtration Type Y disposable filter bags x Ey PA RATION BAGS PA RA S 2 HEPA FILTRATION BAGS It is imperative that you use only genuine HOOVER filter bags distrib uted by The Hoover Company to a
16. own at top of door and pulling door outward Switch A above bag door should be in OFF position Place nuts in recessed areas on front of handle Hold each nut in place while tightening each bolt securely with a Phillips screw driver STEP II Attach hose Align end of hose with projections A over slots B in dirt duct While holding rack in place slide Push bolts into holes on back of handle onto cleaner body handle Make sure tab is inserted fully into slot Reposition bag door by fitting tabs Press cord into the 3 notches and on bottom of door into opening the clip as shown Press top of door to snap securely shut NOTE Hose must be connected as shown for all operations Slide hose into B and twist hose to Position hose over rack and into lock it into place hose tube D or E depening on Lift hose tube cover C your model STEP Ill Position tools Place smaller unridged end of wand into bottom of rack Snap wand into clip Repeat with other wand Open tool cover Cleaner description Polarized plug To reduce the risk of electric shock this appliance has a polarized plug one blade is wider than the other This plug will fit in a polarized outlet only one way If the plug does not fit fully in the outlet reverse the plug If it still does not fit contact a qualified electrician to install the proper outlet Do not change the plug in any
17. ring the warranted period This warranty applies when the appliance is purchased in the United States including its territories and possessions or in Canada or from a U S Military Exchange Appliances purchased else where are covered by a limited one year warranty which covers the cost of parts only This warranty does not apply if the appliance is used in a commercial or rental application This warranty only applies when the product is in use in the country or territo ry in which it is purchased Warranty service can only be obtained by presenting the appliance to one of the following authorized warranty service outlets Proof of purchase will be required before service is rendered 1 Hoover Factory Service Centers 2 Hoover Authorized Warranty Service Dealers Depots For an automated referral of autho rized service outlets in the U S A phone 1 800 944 9200 OR visit The Hoover Company on line at www hoover com This warranty does not cover pick up delivery or house calls however if you mail your appliance to a Hoover Factory Service Center for warranty service transportation will be paid one way While this warranty gives you specific legal rights you may also have other rights which vary from state to state If further assistance is needed or if there are questions concerning this war ranty or the availability of warranty ser vice outlets write or phone the Consumer Response Center The Hoo
18. sired while maintaining good cleaning performance Cleaning lightweight flexible rugs Stand on one end of rug and move cleaner toward other end or edge Before reaching edge push down on handle This will lift up the nozzle front of cleaner as shown and will prevent rug from clinging to cleaner Continue to lift up nozzle so that when you have reached the edge it is completely off the rug Move cleaner back to start again lower nozzle and use only forward strokes Edge cleaning Special edge groomers are provid ed on both sides of the nozzle to remove dirt in carpet near base boards and furniture Guide either side of nozzle parallel to edge of carpet or furniture Stair cleaning A stair cleaning handle has been designed for ease in using your cleaner on stairs With handle in operating position place fingers under edge of stair cleaning handle and guide cleaner with other hand on upper handle As an alternative you may use the hose and powered hand tool or fur niture nozzle for stair cleaning Clean from bottom to top When using cleaning tools the agitator will continue to rotate CAUTION To avoid personal injury or unnecessary wear to car pet and to prevent the cleaner rom falling always place it at bottom of stairs How to attach tool cover The tool cover is designed witha break away feature which allows it i snap free if it is pushed open too ar To reattach
19. ssseseeeeee 12 Replacing Agitator Brush Roll 11 Replacing Belt ccsscsssseeesseenes 10 Replacing Edge Groomers 11 Replacing Headlight csseeeee 10 Replacing Filter Bag cssseeseseee 9 Thermal Protector csssesssenseees 11 Warranty cceecssceesseeeesseceesseenenseeenenes 12 2001 The Hoover Company www hoover com a CA l e MINN XXX MODELO CLEANER ASPIRATEUR ASPIRADORA Ge O lo LISTED SERIES SERIE SERIE BAG TYPE SAC TYPE BOLSA TIPO FILTER FILTRO FILTRE CARTRIDGE PART NO HOUSEHOLD TYPE TYPE MENAGERTIPO DOMESTICO SERIAL NO NUMERO SER NUMERO DE SERIE xX o 8 XXX XXX THE HOOVER CO SERIAL NUMBER N CANTON OH 44720 Important Safeguards When using an electrical appliance always follow basic precautions including the following READ ALL INSTRUCTIONS BEFORE USING THIS APPLIANCE a E Warn ng m To reduce the risk of fire electric shock or injury Do not use outdoors or on wet surfaces e Close supervision is necessary when any appliance is used by or near children Do not allow vacuum cleaner to be used as a toy or to run unattended at any time Keep hair loose clothing fingers feet and all parts of body away from openings rotating agitator and other moving parts Do not operate cleaner in bare feet or when wearing open toe shoes or sandals Do not pick up anything that is burning or smoking such as cigarettes
20. ssure that your cleaner operates at peak performance HOOVER bags can be identified by these trade marks Hoover amp Changing filter bag Disconnect cleaner from electrical outlet Removing bag door To change filter bag press down at top of bag door and pull door for ward Remove door Secondary and final filters Cleaning secondary filter Disconnect cleaner from electrical outlet The secondary filter A located behind the grill in the bottom of bag compartment protects the motor from dirt particles If filter becomes dirty pull off grill and lift out filter Hand wash filter in cold water with mild detergent then air dry Reposition dry filter and grill Should you want to replace this filter ask for HOOVER part No 38765019 Removing and installing filter bag Grasp filter bag collar A and pull collar from tube B Note Do not clean out old filter bag and reuse Discard used filter bag Hold new filter bag as shown Align opening in filter bag with B Push A firmly onto B Tuck in filter bag Cleaning final filter The final filter assists in the filtra tion process to return clean air to the room To remove this filter when it be comes dirty open the door on the side of the cleaner Lift out filter B and hand wash it in cold water with mild detergent Let filter air dry and reposition it on the side of the cle
21. tlet locations U S only Do not send your cleaner to The Hoover Company in North Canton for service this will only result in delay How to replace Disconnect cleaner from electrical outlet Remove bottom plate belt and agi tator following directions in The belt section beginning with Fig 3 Discard old agitator Continue following the directions in The belt section to reposition belt new agitator and bottom plate Lubrication The motor is equipped with bear ings that contain sufficient lubrica tion for the life of the motor The addition of lubricant could cause damage Therefore do not add lubricant to motor bearings The agitator is equipped with two ball bearings that should be lubricated periodically by a Hoover Factory Service Center or an Authorized Hoover Warranty Service Dealer Depot If further assistance is needed con tact The Hoover Company Consumer Response Center North Canton Ohio 44270 Phone 1 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 Phone 1 800 263 6376 Always identify your cleaner by the complete model number when requesting information or ordering parts The model number appears on the bottom of the cleaner 11 Hoover Cleaning Performance This Hoover Cleaning Performance System is for comparing the relative progressive performance of Hoover uprights only and not for compari son with any other brands The major
22. ver Company 101 East Maple St North Canton Ohio 44720 Phone 1 330 499 9499 In Canada contact Hoover Canada Burlington Ontario L7R 4A8 1 800 263 6376
Download Pdf Manuals
Related Search