Chief RXF2 flat panel wall mount
Contents
1. F 1 Hardware Bag e FE 6 M5 x 16mm e FF 6 M5 x 20mm FH 6 M5 x 35mm FO 6 universal washer FS 8 3 ED RMF2 RLF2 RXF2 Installation Instructions Assembly And Installation Install Wall Plate to Wall Wood Studs WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment lt is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm 1 Unfold wall plate A to prepare it for mounting to wall See Figure 1 Figure 2 2x24 Figure 1 2 Level wall plate A and mark locations of pilot holes See Figure 2 NOTE The RMF2 must be installed on two 16 studs The RLF2 can be installed on 16 studs inner holes or 24 studs outer holes For the RXF2 it can be mounted over two or three 16 studs or two 24 studs If mounting to three 16 studs it must be mounted to all three studs using the outer holes and center holes Figure 3 eebe 4 Install 5 16 x 2 1 2 hex head cap screws C through four NOTE The vertical center of the display will be even with the flat washers D wall plate A a2. e If mounting holes are not recessed and both brackets B can lay flat against display then no spacers are required e H mounting holes are recessed or if protrusions prevent brackets B from laying flat then spacers FP or FQ must be used e If additional depth is needed behind display spacers FP and FQ can be stacked on top of each other CAUTION Using screws of improper length may damage your display Proper screws will have adequate thread engagement without contacting bottom of display mounting holes 4 Select screw ength See Figure 8 e Using your hand insert SHORTEST length screw of selected diameter FA FE Fl or FL through bracket B universal washer FS selected spacer FP or FQ if required into display mounting hole Do NOT thread screw into hole at this time e Proper screw length requires base of screw head to protrude above flat washer a distance equal to or greater than the screw diameter If screw length is inadequate select longer screw Select shortest screw which will protrude the required distance 5 Place brackets B on display ensuring See Figure 8 e Upper hooks are towards top of display e Center of brackets B are as close to the center of the back of display as possible after being installed Center of bracket is indicated by the diamond shaped hole 6 Using Phillips screwdriver carefully install selected screws through universal washers FS brackets B and sp
3. E DISPLAY TTS BA CAS a DETAIL A SCALE 1 2 DETAILS SCALET 2 DIMENSIONS RXF2 908 1 Le 35 75 _ WALLPLATE La leng sl OPENING I I 8128 1165 m 32 00 hd c QLETO CENTERLINE 609 6 i ges mit ON THE 24 00 il WALLPLATE 406 4 ms 01 1 16 00 13 117 4 gt UP TO 154 5 4 ur It SPACERS Gu D II D I P NALLPLATE 7 i i OPENING x l itt j i I s I a E i ts gt HA 4 Les 1 51 u CENTERLINE TO BUTTON OF WALLPLATE OPENING ele i DI WE KICESTAND LANYARDS dii DETRILA UREN CIC ESTA NO HH SCALET 2 S ACTIVATED THE FORLOCR DISPLAY THTS RACKS DETAIL B SCALE 1 2 RMF2 RLF2 RXF2 Installation Instructions LEGEND Tighten Fastener Apretar elemento de fijaci n Befestigungsteil festziehen Apertar fixador Serrare il fissaggio Bevestiging vastdraaien Serrez les fixations Pencil Mark Marcar con l piz Stiftmarkierung Marcar com l pis Segno a matita Potloodmerkteken Marquage au crayon Loosen Fastener Aflojar elemento de fijaci n Befestigungsteil l sen Desapertar fixador Allentare il fissaggio Bevestiging losdraaien Desserrez les fixations Drill Hole Perforar Bohrloch Fazer furo Praticare un foro Gat boren Percez un trou Phillips Screwdriver Destornillador Phillips Kreuzschlitzschraubendreher Chave de fendas Phillips Cacciavit
4. INSTALLATION INSTRUCTIONS Universal Fixed Mounts GCHIEF RMF2 RLF2 RXF2 Our Mounts Your Visi RMF2 RLF2 RXF2 Installation Instructions DISCLAIMER Milestone AV Technologies and its affiliated corporations and subsidiaries collectively Milestone intend to make this manual accurate and complete However Milestone makes no claim that the information contained herein covers all details conditions or variations nor does it provide for every possible contingency in connection with the installation or use of this product The information contained in this document is subject to change without notice or obligation of any kind Milestone makes no representation of warranty expressed or implied regarding the information contained herein Milestone assumes no responsibility for accuracy completeness or sufficiency of the information contained in this document Chief is a registered trademark of Milestone AV Technologies All rights reserved IMPORTANT VVARNINGS AND CAUTIONS WARNING A WARNING alerts you to the possibility of serious injury or death if you do not follow the instructions CAUTION A CAUTION alerts you to the possibility of damage or destruction of equipment if you do not follow the corresp
5. NYARDS A KEN KICKSTAND S ACTIVATED THE DISPLAY THTS BACKS USING SPACERS fi H WALL PLATE E OPENING D D 501 7 19 75 WALLPLATE DREN ING 406 4 16 00 if UP TO 1 54 ORIENTATION AND CENTERLINE TL WE IL i El CENTERLINE H DO NO Y Installation Instructions RMF2 RLF2 RXF2 DIMENSIONS RLF2 723 9 28 50 WALL PLATE ia PEW ING Du rt UITING e 18094 del RO LETO CENTERLINE i ARROW ON THE 8 1 is WALL PLATE 34 406 4 Bii 16 00 15 34 ua A Te SN Gate CSC UT Be x O WALLPLATE ee KE De E i i MJ i GC TEL USING SPACERS i i H H e bibi pio i Ll I 0 0 Lest 15 75 E E ES 8 im o WAX E H Y 0 9 H 3 SS a G SE H FI 63 5 O RIEN TATION y T 4 y 151 AND CENTER LIE 6 I 1 CENTERLINE NOTCHES a CENTERLINE TO BD TION OF E DIAMOND LICKSTAND LANYARDS WALL PLATE WHEN CIC ESTA LO ENING CTW ATED TH
6. acers FP or FQ if required into display See Figure 8 7 Tighten all screws Ensure all applicable display mounting holes 4 6 or 8 are used non recessed holes FA FO x4 x6 x8 FS x4 x6 x8 recessed holes or extra depth needed FA FO x4 x6 x8 FS x4 x6 x8 If additional depth is needed spacers FP or FQ can be stacked on top of each other Figure 8 Installation Instructions RMF2 RLF2 RXF2 Install Display to Wall Plate view from left side WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment lt is the installer s responsibility to make sure the combined weight of all components attached does not exceed 125 lbs 56 7 kg for the RMF2 and RLF2 or 175 Ibs 79 4 kg for the RXF2 Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury WARNING Display may be very heavy Ensure display can be safely lifted and maneuvered as required to install on wall plate Failure to take adequate precautions can result in serious personal injury or damage to equipment kickstand engaged WARNING Interface brackets must be hung on opposite sides of the center tab on wall plate See Figure 9 interface brackets must be hung on opposite Figure 10 sides of center tab NOTE Any cable management or rear display adjustments should be made when
7. e a stella Kruiskopschroevendraaier Tournevis pointe cruciforme Adjust Ajustar Einstellen Ajustar Regolare Afstellen Ajuster Open Ended Wrench Llave de boca Gabelschl ssel Chave de bocas Chiave a punte aperte Steeksleutel Cl fourche Remove Quitar Entfernen Remover Rimuovere Verwijderen Retirez By Hand A mano Von Hand Com a m o A mano Met de hand la main Optional Opcional Optional Opcional Opzionale Optie En option LI d y 4 d Hex Head Wrench Llave de cabeza hexagonal O D OD Q CG Sechskantschl ssel Chave de cabe a sextavada Chiave esagonale Zeskantsleutel Cl a t te hexagonale Security Wrench Llave de seguridad Sicherheitsschl ssel Chave de seguranca Chiave di sicurezza Veiligheidssleutel Cl de s curit RMF2 RLF2 RXF2 Installation Instructions TOOLS REQUIRED FOR INSTALLATION 7 32 5 5mm 5 16 7 9mm 1 2 12 7mm PARTS A I For below kit quantities are 4 for RMF2 and wall plate RLF2 shown vertical bracket RLF2 6 for RXF2 e C 4 or 6 5 16 x 2 1 2 D 4 or 6 1 4 6 4mm E 4 or 6 concrete anchor
8. esired mounting location See Figure 5 NOTE For the RLF2 either the inner or outer four holes may be used NOTE For the RXF2 use the outer four holes and the two middle holes on wall plate for installation NOTE The vertical center of the display will be even with the center line indicated on the labels located directly below each hinge Keep this in mind when determining mounting location See Figure 5 CENTER Figure 5 3 Drill 5 16 7 9mm diameter pilot holes into wall at marked locations Holes must be drilled at least 2 1 2 inches deep See Figure 5 4 Install four or six concrete anchors E into drilled holes Use a hammer to tap anchors into holes See Figure 6 Figure 6 5 Using 1 2 12 7mm wrench install screws C through flat washers D wall plate A and into concrete anchors E See Figure 7 D RMF2 RLF2 RXF2 Installation Instructions Install Brackets to Display WARNING The minimum hole pattern size is 100mm x 100mm for the RMF2 and 200mm x 200mm for the RLF2 and the RXF2 1 Lay display face down on protective surface CAUTION Using screws of improper diameter may damage your display Proper screws will easily thread into display mounting holes 2 Select screw diameter by examining hardware FA FO 8mm 6mm 5mm or 4mm and comparing with mounting holes on display See Figure 8 3 Select spacers See Figure 8
9. le Creek Parkway Savage MN 55378 800 582 6480 952 894 6280 877 894 6918 952 894 6918 Fellenoord 130 5611 ZB EINDHOVEN The Netherlands 31 0 40 2668620 31 0 40 2668615 Office No 1 on 12 F Shatin Galleria 18 24 Shan Mei Street Fotan Shatin Hong Kong 852 2145 4099 852 2145 4477 I al d D 1 Yr consume
10. nd into wood studs See center line indicated on the labels located directly Figure 4 below each hinge Keep this in mind when determining mounting location See Figure 3 3 Drill 7 32 5 5mm diameter pilot holes into wood studs at marked locations See Figure 2 Figure 4 Installation Instructions RMF2 RLF2 RXF2 Install Wall Plate to Wall Concrete Concrete Block or Brick WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment lt is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component WARNING ELECTRICAL SHOCK HAZARD CUTTING OR DRILLING INTO ELECTRICAL CORDS OR CABLES CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of electrical wires and cables before drilling or installing fasteners WARNING EXPLOSION AND FIRE HAZARD CUTTING OR DRILLING INTO GAS PLUMBING CAN CAUSE DEATH OR SERIOUS PERSONAL INJURY ALWAYS make certain area behind mounting surface is free of gas water waste or any other plumbing before cutting drilling or installing fasteners 1 Unfold wall plate A to prepare it for mounting to wall See Figure 1 2 Level wall plate A and mark locations of pilot holes at d
11. onding instructions DIMENSIONS RMF2 WARNING Failure to read thoroughly understand and follow all instructions can result in serious personal injury damage to equipment or voiding of factory warranty It is the installer s responsibility to make sure all components are properly assembled and installed using the instructions provided WARNING Failure to provide adequate structural strength for this component can result in serious personal injury or damage to equipment It is the installer s responsibility to make sure the structure to which this component is attached can support five times the combined weight of all equipment Reinforce the structure as required before installing the component The wall to which the mount is being attached may have a maximum drywall thickness of 5 8 1 6cm WARNING Exceeding the weight capacity can result in serious personal injury or damage to equipment lt is the installer s responsibility to make sure the combined weight of all components attached does not exceed 125 Ibs 56 7 kg for the RMF2 and RLF2 or 175 Ibs 79 4 kg for the RXF2 Use with products heavier than the maximum weight indicated may result in collapse of the mount and its accessories causing possible injury 1448 Di Lli 1 41 val PO UNS HOLE TO CENTERLINE ERO DICTRE SE Virum 8 63 5 H 1350 K CENTER LIE 10 BOTTON OF UC ESTA NO LA
12. the display is resting on the kickstand Figure 9 1 Make sure interface brackets are in the kickstand position by pulling down on handles as far as possible See Figure 10 2 Hang display with brackets B on upper rail of wall plate A Kickstand should be engaged with lower portion of wall plate See Figure 10 RMF2 RLF2 RXF2 Installation Instructions views from left side kickstand against wall locked position 10 Figure 11 Unlock kickstand by pushing up on interface brackets until kickstand rests against the wall See Figure 11 Push up on the interface brackets further in order to lock display into position against wall See Figure 11 Straps can be tucked behind display on notch on interface brackets B after installation is complete so that they will not be visable to the viewer See Figure 9 Optional Route padlock or cable lock not included through bottom holes on interface bracket to provide additional security See Figure 11 Installation Instructions RMF2 RLF2 RXF2 11 RMF2 RLF2 RXF2 Installation Instructions GCHIEF Our Mounts Your Vision Chief Manufacturing a products division of Milestone AV Technologies 8800 002048 REV 00 2010 Milestone AV Technologies a Duchossois Group Company www chiefmfg com 01 10 USA International Europe Asia Pacific Tnu TU 8401 Eag
Download Pdf Manuals
Related Search