Home

Moxa OnCell G2110-T

1. Connecting Power The power connector 1s a 3 pin terminal block It can connect to different types of field power sources that support 12 to 48 VDC When power is connected the PWR LED will light up It will glow a steady green when the system is ready 2 9 OnCell G2100 Series User s Manual Getting Started A terminal block adaptor with power jack connector is provided to connect to AC power instead of DC power Compatible AC power adaptors are listed on the Moxa website www moxa com ATTENTION Always install the antenna first and then connect power Do not connect power 1f the antenna has not been installed Doing so may damage the unit Connecting a Serial Device The RS 232 serial interface come with 15 KV ESD serial line protection and matches the pinouts of a standard D shell connector A serial device or PC COM port can be connected with a DB9 M to DB9 F serial cable such as Moxa s CBL F9M9 150 100 cm or CBL F9M9 20 20 cm m M m AUU UREA CBL F9M9 150 or 3 CBL F9M9 20 gt p PC or RS 232 Devices p p p Meter Meter Meter RS 485 Multi dropped devices For OnCell G21501 Only A separate 5 pin terminal block connector on the bottom panel is used for RS 422 2 wire RS 485 and 4 wire RS 485 connections A built in 120 Q terminal resistor can be activated by DIP switch if required Pull high low resistor adjustments are also allowed Bot
2. IF your SIM card requires a PIN enter it here oond f m St Defaults 3 13 OnCell G2100 Seriesi User s Manual OnCell Configurator A ATTENTION Once the correct PIN is entered using the AT CPIN command or OnCell Configurator the system firmware V1 2 or above will activate the Automatic PIN Entry function This function will store the current PIN in its memory and then enter the PIN automatically each time the system boots up If the SIM card does not match the current PIN the Automatic PIN Entry function will be deactivated To activate the Automatic PIN Entry function again use the AT CPIN command or OnCell Configurator to enter the correct PIN To disable the Automatic PIN Entry use the AT USEPIN 0 command Please refer to the OnCell G2100 Series AT Commands Set which can be found on the Document and Software CD The following instructions show how to configure the PIN code using Wizard 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 2 Start OnCell Configurator and select the Create a new Configuration File from Wizard option 2 OnCell Configurator X Welcome to the OnCell Modem Wizard Use this wizard to set up pour OnCel G2700 cellular modem Create a Configuration File Create a new Configuration File from Configurator f Create a new Configuration File from Wi
3. PATEE File name Fw_G21501_1 2 img A E My Documents e My Computer Loy Network Places Files of type Img files img Cancel A ATTENTION Be sure to use the right firmware image file for your model The OnCell G2110 and OnCell G2110 T both use the same firmware image file The OnCell G2150I uses a different firmware image file 6 Select the appropriate COM port and communication parameters for connecting to the modem Click OK to proceed Connect Setup al Connection Setu COM Port eom y Flow Control None y Baud Rate 115200 E Data Bits Stop Bits Parity OK Cancel 3 34 OnCell G2100 Seriesi User s Manual OnCell Configurator A ATTENTION If you are not sure which communication parameters you should use please select the Auto Detect Serial Settings option and follow the onscreen instructions The procedure may take few minutes to complete When using the Auto Detect Serial Settings function if the GSM or the GPRS LED is ON or blinking you must remove the SIM card or use the escape command on the terminal to disconnect the current connection The default parameters are 115200 8n1 and RTS CTS flow control de Wait a few moments for the firmware to be downloaded to the OnCell G2100 Series modem Upgrade Firmware To Modern Loading LTT TT 8 Click OK to finish OnCell Configurator X Upgrade Firmware Complete 3 35 On
4. OTRA Drop Acto Ignore DTA C Command Mode a T Get Settings Hang Up fis e Aki mi i Sig Strength GSM Autobauding C S50MHz C SO0MHz GSM lt gt G5M AH Upgrade Fy 1800MHz 1900MHz C 50 1900MHz z m sa eta f 900 1800MHz LL C 900 1900MHz 4410 3600 GSM lt gt 1501 32 9600 G5M lt gt 4nalog Modem The following instructions illustrate how to configure the radio band using the Wizard 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 2 Start OnCell Configurator and select the Create a new Configuration File from Wizard option 2 OnCell Configurator xi Welcome to the OnCell Modem Wizard Use this wizard to set up pour OnCel 6100 cellular modem Create a Configuration File Create a new Configuration File from Configurator Load a Configuration File Load an existing Configuration File to Configurator Hent Cancel 3 16 OnCell G2100 Series User s Manual OnCell Configurator 3 On the PIN and Band Management page select the correct radio band for your application 2 OnCell Configurator x PIN and Band Management SIM Card PIN Setup IF your SIM card requires a PIN 230MH2 300M Hz enter it here 1800MHz 1500MHz 690 1 300MH2 300 1 800MHz 300 1 3004 H 2 Back Hent Can
5. YN 2 The following example shows how to delete all short messages in the storage ES PComm Terminal Emulator COM1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help a BA alaa 328 E com1 115200 None 8 1 Dumb Terminal A ATTENTION Please refer to the OnCell G2100 Series AT Command Set on the Document and Software CD for additional information on AT commands for SMS 6 3 OnCell G2100 Series User s Manual Using Short Message Services SMS Tunnel Mode A major benefit of GSM technology is that it supports short messages SMS for easy communication over the mobile network Moxa s proprietary SMS Tunnel Mode allows you to expand your applications and reduce cost For example SMS Tunnel Mode can be used to update the message on a highway display panel place refill orders for vending machines or handle maintenance for remote rental equipment SMS Tunnel Mode can even generate SMS alarms by converting text binary or Unicode data from a legacy device to short messages without the use of AT commands SMS Tunnel Mode is particularly suitable for devices that communicate infrequently or lack access to the local network SMS Tunnel Mode converts both ASCII and binary data to short messages transparently and bidirectionally In addition caller ID phone number can be used to block messages from uncertified users broadcast messages and unwanted SMS advertisements SMS Tunnel Mode has the following
6. onell G2100 Series User s Manual Fourth Edition November 2007 www moxa com product Moxa Technologies Co Ltd Tel 886 2 8919 1230 Fax 886 2 8919 1231 Web www moxa com Moxa Technical Support Worldwide support moxa com The Americas support usa moxa com OnCell G2100 Series User s Manual The software described in this manual is furnished under a license agreement and may be used only in accordance with the terms of that agreement Copyright Notice Copyright 2007 Moxa Technologies Co Ltd All rights reserved Reproduction without permission is prohibited Trademarks Moxa is a registered trademark of The Moxa Group All other trademarks or registered marks in this manual belong to their respective manufacturers Disclaimer Information in this document is subject to change without notice and does not represent a commitment on the part of Moxa Moxa provides this document as is without warranty of any kind either expressed or implied including but not limited to its particular purpose Moxa reserves the right to make improvements and or changes to this manual or to the products and or the programs described in this manual at any time Information provided in this manual is intended to be accurate and reliable However Moxa assumes no responsibility for its use or for any infringements on the rights of third parties that may result from its use This product might include unintentional
7. Back Cancel ATTENTION The phone number 99 is a special phone number that is used globally to request GPRS IP service from the carrier DO NOT modify this phone number in any way The same number is used regardless of the country that you are located in 7 Enter the User name and Password as prompted and click Next New Connection Wizard l j Internet Account Information You will need an account name and password to sign in to Your Internet account Type an SP account name and password then write down this information and store it in a sale place If you have forgotten an existing account name or password contact your ISP User name ispdaticingulargors com Password ES Confirm password ES Use this account name and password when anyone connects to the Internet from this computer Make this the default Internet connection lt Back Cancel 7 14 OnCell G2100 Series User s Manual GPRS Connection ATTENTION For a list of User names and Passwords refer to APN List on the Document and Software CD or consult your service provider for further details 8 Click Finish New Connection Wizard Completing the New Connection Wizard You have successtully completed the steps needed to create the following connection Cingular Wireless Share with all users of this computer The connection will be saved in the Network Connections folder e Add a shortcut to this connection to m
8. MSN fin Games fin MW Snap pY windows Media fam Startup 8 Internet Explorer Tour Windows xi MSN rer F F 00 5 OG Files and Settini ES Wizard c Remote Assistance A Windows Media Player fag PEommLite i ES Mzterm Y Paint 3 Windows Messenger E 621501 Help a Windows Movie Maker JE oncell Configurator fag OncCell Configurator be E Uninstall Onell Configurator Log OFF o Turn OFF Computer The PComm Terminal Emulator user interface will appear Click the Open button which is the first blue icon on the tool bar All Programs sPComm Terminal Emulator Port Manager Help FA loli la s Slzsl 4 3 OnCell G2100 Series User s Manual AT Command Set 4 Select the target COM port and communication parameters Click OK to open the port E7 Communication Parameter Terminal File Transfer Capturing COM Options Forts Baud Rate Data Bits Parity Stop Bits Output State OTA ON OFF Flow Control C ATS CTS SON A XOFF RATS ON OFF E 5 Terminal Emulator will connect to the target COM port ES PComm Terminal Emulator COMi1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help el BR a f5 s e 3 28 E com1 115200 None 8 1 Dumb Terminal OTF lars 4 4 OnCell G2100 Series User s Manual AT Command Set AT Command Examples The following examples can give users a bett
9. RSSI should be higher than 12 if you wish to create or accept GSM CSD data calls or establish a GPRS connection If the RSSI is less than 12 you will only be able to transmit and receive SMS short message Another way to verify RSSI is to check the SIGNAL LEDs on the front panel See Chapter 2 for more information Radio Band Selection Although GSM 900 and GSM 1800 are used in most parts of the world operators in United States Canada and many other countries in the Americas use GSM 850 or GSM 1900 A quad band industrial cellular modem such as the OnCell G2100 Series modem makes it relatively easy to prepare the product for shipment to different parts of the world The GSM GPRS band of OnCell G2100 Series is configured to 900 1800 MHz by default For users NOT in this service area follow the instructions below to set up the correct radio bands A ATTENTION The following procedures can also be carried out using OnCell Configurator 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC Start PComm Terminal Emulator using the current communication parameters default 115200 bps 8 data bits None parity 1 stop bits and no flow control 2 Type AT WMBS x where x represents one of the band selections shown in the following table and then press Enter o Mono band 850 MHZ IC ES 4 6 OnCell G2100 Series User s Manual AT Command Set For example users in North America would type the follow
10. E Uninstall Onell Configurator Log OFF o Turn OFF Computer OnCell G2100 Seriesl User s Manual OnCell Configurator 2 Select one of the three options OnuCell Configurator Welcome to the OnCell Wizard Use this wizard to set up pour Onell 62100 cellular modern 3 Whether you use the Configurator or the Wizard any modifications to the settings will not 3 9 OnCell G2100 Seriesl User s Manual OnCell Configurator Configuring Serial Connection and Device Name The following instructions explain how to configure the serial communication parameters using Configurator 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 2 Start OnCell Configurator and select Create a new Configuration File from Configurator 42 OnCell Configurator x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modem ee e Create a new Configuration File from Configurator gt Create a new Configuration File from wizard Load 4 Configuration File Load an existing Configuration File to Configurator E Cancel 3 On the Basic Setting tab click Modify and configure the serial interface as necessary Enter the device name in the text input box 2 OnCell Configurator Ioj x Fie Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings D
11. Profile Edit Port Manager Window Help el BR alale 328 E c0m1 9600 None 8 1 Dumb Terminal Modifying Data Bits and Parity 1 Type AT ICF x y and press Enter where x and y correspond to the following parameters ww aap x Data bits stop bits For example type AT ICF 5 1 to change the parameters from 8n1 to e71 ES PComm Terminal Emulator COM1 9600 None 3 1 0umb6 Terminal Profile Edit Port Manager Window Help el Bika alale z2 E c0M1 9600 None 8 1 Dumb Terminal 4 Jattic ESB 1 OnCell G2100 Series User s Manual AT Command Set 2 Modify the terminal settings to match the new serial communication parameters ee Communication Parameter Terminal File Transfer Capturing COM Options Forts Baud Rate Data Bits Parity Stop Bits Output State DTA ON C OFF Flow Control M RATSACTS SON AOFF ATS ON OFF Cancel 3 Type AT amp W and press Enter to save the settings ES PComm Terminal Emulator COM1 9600 Even 7 1 bumb Terminal Profile Edit Port Manager Window Help el BA alae 32 E co0m1 9600 Even 7 1 Dumb Terminal A ATTENTION Changes to the serial communication parameters take effect immediately You will need to update your terminal settings to match any changes in the serial communication parameters Autobauding and escape command only work with 8n1 or e71 settings Using other settings wil
12. Setup installs OnCell Configurator on your computer 11 Click Next to proceed h Setup OnCell Configurator Information Please read the following important information before continuing gt OnCell 62150162110 08 28 2007 Company Moxa Technologies Co Ltd Support Plathorrn Windows 2000 Windows lt P Windows 2003 Windows xP x64 Edition Windows 2003 64 Edition 3 7 OnCell G2100 Series User s Manual 12 Click Finish Setup OnCell Configurator OnCell Configurator Completing the OnCell Configurator Setup Wizard Setup has finished installing OnCell Configurator on your computer The application may be launched by selecting the Installed iconz Click Finish to exit Setup Launching OnCell Configurator 1 Start OnCell Configurator from the Windows Start menu Internet 24 Internet Explorer S Ey Set Program Access and Defaults ey E mail aa J Outlook Expres E Windows Catalog i My Documents nts F o Windows Update Windows Messe F MSN Pomm Termina va o amp Windows Media y MSH ea Tour Windows gt 6 i Files and Settim _ l i Windows Messenger a Windows Movie Maker O Wizard All Programs Accessories Games PMySsnap PComm Lite erl 3 Startup Se Ee Yr F F a Internet Explorer Outlook Express p Remote Assistance 15 Windows Media Player E G21501_Help 2 Oncell Configurator fag OncCell Configurator G
13. an tal STEP 3 Use screws and the mounting appendages to Reattach the terminal block s to the modem mount the unit onto the wall i OnCell G2100 Series User s Manual Getting Started Connecting the Antenna A ATTENTION Make sure the transmitter antenna is placed so that it is at least 20 cm 8 inches away from any people or users The modem is not designed for applications where users will be in close proximity for prolonged periods Turn the unit off for the following situations e When in an aircraft e When around gasoline or diesel fuel pumps and before filling your vehicle with fuel When in hospitals and any other place where medical equipment may be in use Respect any restrictions on the use of radio equipment especially around fuel depots chemical plants and blasting operations The OnCell G2100 Series modem may present a hazard for inadequately protected personal medical devices such as hearing aids and pacemakers Consult the manufacturer of the medical device to determine if it is adequately protected The OnCell G2100 Series modem may cause interference for inadequately protected electronic equipment Observe any warning signs and manufacturers recommendations All OnCell G2100 Series modems are shipped with a 0 dBi antenna with SMA connector and magnetic mount The 3 meter patch cord is ideal for installing the modem in places such as a metal cabinet or a vending machine PLOT TT Se
14. be capitals and lt pin gt is the correct PIN The following example shows 0000 being entered for the PIN ES PComm Terminal Emulator COM1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help el Bika alale 32 EA com1 115200 None 8 1 Dumb Terminal lars attcpin CPIN SIM FIN at cpin 0000 DE attclck 5C 0 0000 DE 4 8 OnCell G2100 Series User s Manual AT Command Set 3 To enable the facility lock type AT CLCK SC 1 lt pin gt The following example shows 0000 being used for the PIN ES PComm Terminal Emulator COM1 115200 None 8 1 Dumb Terminal Profile Edit Port Manager Window Help el BA elelelsjer 52 E com1 115200 None 8 1 Dumb Terminal A ATTENTION Once the correct PIN is entered the system firmware V1 2 or above will activate the Automatic PIN Entry function This function will store the current PIN in its memory and enter it into the OnCell G2100 Series modem each time the system boots up If the SIM card does not match the current PIN the Automatic PIN Entry function will be deactivated To activate the Automatic PIN Entry function again use the AT CPIN command or OnCell Configurator to enter the correct PIN To disable Automatic PIN Entry once and for all use the AT USEPIN 0 command 4 9 OnCell G2100 Series User s Manual AT Command Set Serial Line Settings A ATTENTION Changes to the serial communication parameters take effect imm
15. for GRPS access A ATTENTION The specific steps may vary depending on your version of Windows and your Windows settings 7 2 OnCell G2100 Series User s Manual GPRS Connection Installing Modem Driver 1 In the Control Panel open Phone and Modem Options and go to the Modem tab Click Add to add a new modem Phone and Modem Options x Dialing Rules Moderns Advanced es The following modems are installed Re Attached To Remove Properties ATTENTION The first time you access the Phone and Modem Options Windows will ask you to input the area code Enter the area code to proceed 2 When the Install Mode window opens select Don t detect my modem I will select it from a list and click Next Add Hardware Wizard Install New Modem Do you want Windows to detect your modem Windows will now try to detect your modem Before continuing you should 1 Ifthe modem ls attached to your computer make sure it is turned on 2 Quit any programe that may be using the modern Click Nest when you are ready to continue Dont detect my modem will select it from a list lt Back Cancel 7 3 OnCell G2100 Series User s Manual GPRS Connection 3 Next click Have Disk Add Hardware Wizard Install New Modem Pha te Y Select the manufacturer and model of your modem IF your modern le not listed cr if you have an installation
16. technical or typographical errors Changes are periodically made to the information herein to correct such errors and these changes are incorporated into new editions of the publication Chapter 1 Chapter 2 Chapter 3 Chapter 4 Table of Contents o e ea emaeeteaa 1 1 ONEIN E pacha sa tes acs E ogee oS edge ada Gk ae 1 2 Package O AAA O A A A A re 1 2 nl A cae 1 2 PECET ON A O Ae O A A A IR Te AO oe 1 3 AS le 1 5 GETING SUAS AAA A E 2 1 Product Chataotens ES a AA cada 2 2 Dimensions ad 2 2 O75 Bell ME TO Meee eer een A E 2 2 Ocel CAT 2 3 Connecting Ahe Hard WALES litio 2 4 Wiring Requirements oscinina ai ana a a r a a a a a 2 4 SIM Card Msalato cano 2 5 DIN Ra Monin an ae aS 2 5 Wall MOUNIE 02s esas a a E OAE anes 2 8 Connecti mie THE ADONNE A A ee Ree 2 9 CONECTA FOWE T airera EA NE T E ee EAE T eas 2 9 Connecting a neral Devices 2 10 CEDOLINO tania dial 2 11 ONGEell ContiguralO omar tata adi 3 1 DA A A cat EEEE EE EAE clue eaten tae in AAE eae 3 2 Instalhnge OnCell C onieuratOr ds 3 3 Launching OnC ell Conte urator A ia 3 8 Configuring Serial Connection and Device Name ccccccccceceseeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeeees 3 10 Coniieuring the PINES CHiN s ciactencssavtoauwtcenatsencuens A toes 3 13 Conmeurnothe Radio Bad rl 3 15 RS TO PE e 3 17 Saving he Contisuration Prol tidad 3 18 Apps Modeni Senine Serseri a dias a aa tase aa 3 20 Reticvine the Modents emos di 3 23 Esad a Po a 3 26 Signal Stengt M
17. to connect to a PC s serial port If you use a USB to serial product to configure the OnCell G2100 Series modem we strongly recommend using Moxa s UPort 1110 Other USB to serial products may cause unexpected errors when configuring the OnCell G2100 Series modem 2 Start OnCell Configurator and select the Create a new Configuration File from Configurator option 2 OnCell Configurator x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modern Load 4 Configuration File Load an existing Configuration File to Configurator E Cancel 3 23 OnCell G2100 Series User s Manual OnCell Configurator 3 Click the Get Settings button on the right side of the window 2 OnCell Configurator Ioj x File Terminal Emulator Help Serial Interac Device Name T Modify Baud Rate fiiszoo Flow Control None y Data Bits Stop Bits ph Parity None Disable Echo if Get Settings A 2 Sig Strength AH Upgrade Fis r Set Defaults SIM Card PIN Setup IF your SIM card requires a PIN enter it here 4 Select the appropriate COM port and communication parameters for connecting to the modem Click OK to proceed 2 Connect Setup X Connection Setu COM Fort Com Flow Control Hone Baud Fate 115200 Data Bits E Stop Bits Parity OF Cancel ATTENTION If you are not sure w
18. 422 485 OnCell G2100 Series User s Manual Introduction Serial Communication Parameters Parity Data Bits Stop Bits Flow Control Transmission Speed RS 422 485 Termination RS 422 485 Pull High Low Isolation Serial Line Protection Power Requirements Power Input Power Consumption None Even Odd Space Mark 7 8 lia RTS CTS None 300 bps to 115 2 Kbps 1200 DIP switch controlled OnCell G2150I only 150 KQO 1 KQ OnCell G21501 only 2 5 KV RMS for 1 minute on all serial signals OnCell G2150I only 15 KV ESD 12 to 48 VDC 50 mA 12V when idle 300 to 900 mA peak 12V during data link Mechanical Specifications Material Dimensions Weight Environment Operating Temperature Storage Temperature Regulatory Approvals CE FCC Limited Warranty Period PC ABS IP30 rating 27 x 123 x 79 mm 150 5g 20 to 55 C 32 to 131 F 5 to 95 RH 30 to 75 C 32 to 167 F 5 to 95 RH OnCell G2110 T only 40 to 75 C 4 to 167 F 5 to 95 RH Class A 5 years OnCell G2100 Series User s Manual Introduction Pin Assignments 54321 OJE E E B HO 9876 1 5 DB9 Female for RS 232 Terminal Block for RS 422 485 RS 485 RS 485 MET 422 EENI wire O TxD O oTxD A AS O 223 RD RxD RxDt Data B 4 DSR RxD RxD Data A O l o RS 422 and RS 485 are available on the OnCell G2150I only 2 Getting Started This chapter includes instructio
19. Cell G2100 Series User s Manual OnCell Configurator Setting Modem Defaults The following instructions illustrate how to use Configurator to load the factory default settings into the OnCell G2100 Series modem l Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON ATTENTION The RS 232 connector uses the standard pinouts A direct male DB9 to female DB9 cable such as Moxa s CBL F9M9 150 100 cm or CBL F9M9 20 20 cm can be used to connect to a PC s serial port If you use a USB to serial product to configure the OnCell G2100 Series modem we strongly recommend using Moxa s UPort 1110 Other USB to serial products may cause unexpected errors when configuring the OnCell G2100 Series modem 2 Start OnCell Configurator and select the Create a new Configuration File from Configurator option x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modem a Configuration File f Create a new Configuration File from Configurator Create a new Configuration File from Wizard Load a Configuration File Load an existing Configuration File to Configurator E Cancel 3 36 OnCell G2100 Series User s Manual OnCell Configurator 3 Click Set Defaults on the right side of the window 2 OnCell Configurator Ioj x Fie Terminal Emulator Help Device N
20. ES COM1 115200 None 3 1 0umb Terminal laca a 1s entered here ATTENTION is the escape sequence and ATH is the hang up command For international calls the local international prefix does not required but the character is You would type ATD 886289191230 5 3 OnCell G2100 Series User s Manual GSM CSD Connection Answering a CSD Connection PComm Terminal Emulator can be used to answer a CSD call manually 1 When the terminal displays RING type ATA and press Enter ES PComm Terminal Emulator COM1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help el altal alale 32 E com1 115200 None 8 1 Dumb Terminal 2 Check the GSM indicator on the front panel If the LED is on and an amber color the CSD connection has been established successfully The modem will automatically switch to data mode At this point you can proceed with data communication PComm Terminal Emulator can be used to configure the modem to answer CSD calls automatically 1 In the terminal window type ATSO x and press Enter For x substitute the number of rings that the modem should receive before answering the call For example to answer after the first ring type ATSO 1 2 Type AT amp W and press Enter ES PComm Terminal Emulator COM1 115200 MNone 8 1 bumb Terminal Profile Edit Port Manager Window Help el BA alala 228 E com1 115200 None 8 1 Dumb Terminal To disconnect the mod
21. Modem Information Hardware ID oncellg S003 35dec Command Response Query Modem Logging Append to Log View log Cancel 3 Ifthe query is successful you will be able to see commands that are sent to the modem and the modem s responses Moxa OnCell G2100 GSM GPRS Modem Properties ES General Modem Diagnostics Advanced Driver Modem Information Hardware ID oncellge 501803 35dcc Command Response a ATOOVIEO COMMAND NOT SUPPORTED AT GMM MULTIBAND 500 1800 AT FCLA5S FCLASS 0 1 2 ATHCLS COMMAND NOT SUPPORTED Logging Append to Log View log 7 9 OnCell G2100 Series User s Manual GPRS Connection setting up the APN Before using GPRS connection in Windows the APN Access Point Name must be added as a modem initialization command The following instructions explain how to set up the APN A ATTENTION Check the signal strength indicators on the front panel of the OnCell G2100 Series modem If the LED indicators are dark then the SIM card is not installed properly or the modem is not picking up a signal If only one bar lights up the signal is not strong enough for a GPRS connection Adjust the position of the antenna change the location of the installation or use an optional high gain antenna instead Make sure that your SIM card account supports GPRS service In most regions you will need to apply with your mobile service provider to activate the service Ma
22. Networks Install Uninstall Properties Description Transmission Control Protocol Internet Protocol The default Wide area network protocol that provides communication across diverse interconnected networks Cancel 14 In the next window that appears click Dial to establish the connection Connect Cingular Wireless 1 2 x Username fispda cingulangprs com Password Ho changa ihe saved password cick haraj IY Save this user name and password for the following users Me only E Arwone who uses this computer Dial a 7 18 GPRS Connection A GPRS with UC 7110 UC 7112 Moxa s UC 7110 and UC 7112 are small embedded computers that can be used for applications such as transportation control light control factory building automation and power utilities However for some applications it is either inconvenient or impossible to connect to the embedded computers with a traditional landline In this case the OnCell G2100 Series modem is a great solution for providing GSM GPRS connectivity to the UC 7110 or UC 7112 4 j gt Embedded Computer GPRS Solution You can refer to step by step installation guide and a reference script in the Linux folder on the Document and Software CD B Federal Communication Commission Interference Statement This equipment has been tested and found to comply with the limits for a Class A digital device pursuant to Part 15 of the FCC Rules Thes
23. ONO AAA AAA 3 30 Uperadine the FEMALE A irr ene earner err ee 3 32 Semin IV OSM Derilis ss a A eens one cereals 3 36 Al Command SC as ccc e a a aa 4 1 AT Command Set Introduction diia 4 2 Starting Moxa rl e ol 4 3 AL Command Example A ii 4 5 Modem Ackno wled mernin a E e a a i 4 5 Veny SIMA CMU 33221 E RO E RO E T one 4 5 Radio ANG SE LE CUOM tada 4 6 PIN Code Mana Mc a 4 7 Ouer the Current PINS AUS oa ai 4 7 Disable theFacility Locos 4 8 Sena TINS Seline a talca Es 4 10 Modifvine TS AU GE AUG olaa 4 10 Modifying Data Bits and Parlty coccccccccccncncnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnnos 4 11 Chapter 5 Chapter 6 Chapter 7 Appendix A Appendix B PTO WC ONCE Os says A ae ee 4 13 2 wire RS 485 Communication OnCell G21501 Only ec ccccccceeeceeeeeeeeeeeeeeeeeeeeeeeees 4 13 Additional I TOT idas 4 14 GSM CSD Connection iii 5 1 ONE Maa 5 2 Initiating aC SD Comme UI iaa 5 2 Answering a CSD Connection iaa 5 4 Using Short Message ServiCes cccccssseesseesseeeeceeseeescesseeeseensseeseeseessees 6 1 Sendinte Short MESS Sr id AAA AAA 6 2 Reading Short NCS SOS ai 6 2 Delete SHOR Mesa ES ae 6 3 SMS TUI MOE nd AAA AAA AAA AAA AS 6 4 GPRS CONMECION msn tilo 7 1 A A 7 2 WACO WS GPRS AC eee a 7 2 istallmo Modeni Dieli ds 7 3 Modeni Dinos es lalala 7 8 Sa td aR id ed tnd da acs 7 10 Adding Windows DUN By sesssiinenesi a tention a aust acuensent 7 12 GPRS with UC 7110 UC 711 2 ou s
24. SD Connection A Circuit Switched Data Connection makes the wireless modem work in a manner similar to a regular analog modem You must have CSD service in order to make a CSD call This chapter covers the following topics Q Overview U Initiating a CSD Connection LJ Answering a CSD Connection OnCell G2100 Series User s Manual GSM CSD Connection Overview CSD Circuit Switched Data is the original form of data transmission developed for GSM systems By using a single radio time slot CSD 1s able to deliver 9 6 to 14 4 kbit s data transmission to both the GSM network and PSTN switching subsystem through direct calls Most of the time it 1s initiated by standard AT commands Using the modem to access remote devices by CSD is often more convenient than installing cables and data lines Data collection and monitoring will be more flexible since CSD can be used for applications that are hard to wire or hard to access Meter 1 626 0001 Si Ae RY 1 626 0002 1 626 0003 Meter Dial up polling topology Meter Initiating a CSD Connection A CSD connection can be initiated using the OnCell G2100 Series modem and PComm Terminal Emulator 1 Start PComm Terminal Emulator with the current communication parameters default 115200 bps 8 data bits None parity 1 stop bit and no flow control ES PComm Terminal Emulator COM1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help al HK Salal x25 E
25. The modem configuration stored in the profile will be displayed in Configurator 2 OnCell Configurator Fie Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings enal Interface M Modify Baud Rate 118200 Flow Control Hone Data Bits E Stop Bits i Parity None Disable Echo Device Mame MOXA TECHNOLOGY SIM Card PIN Setup IF your SIM card requires a PIN enter it here oono 3 29 2101 x Yi r wit tes Sig Strength e AH Upgrade Fis m Set Default OnCell G2100 Series User s Manual OnCell Configurator Signal Strength Monitor The following instructions illustrate how to configure the serial communication parameters using Configurator 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON ATTENTION The RS 232 connector uses the standard pinouts A direct male DB9 to female DB9 cable such as Moxa s CBL F9M9 150 100 cm or CBL F9M9 20 20 cm can be used to connect to a PC s serial port If you use a USB to serial product to configure the OnCell G2100 Series modem we strongly recommend using Moxa s UPort 1110 Other USB to serial products may cause unexpected errors when configuring the OnCell G2100 Series modem 2 Start OnCell Configurator and select the Create a new Configuration File from Configurato
26. Wizard Zz Internet Connection How do vou want to connect to the Internet Connect using a dial up modem This type of connection utes a modem and a regular or ISOM phone line Connect using a broadband connection that requires a user name and password This tg a high speed connection using ether a OSL or cable modem our ISF may refer to this tyoe of connection as PPPoE Connect using a broadband connection that is always on This iz a high speed connection using either a cable modem DSL or LAN connection tis always active and doesn t require you to sign in lt Back Cancel 5 Enter the name of your service provider and click Next New Connection Wizard Connection Name What is the name of the service that provides pour Internet connection Type the name of pour ISP in the following bos ISP Name Cingular Wireless The name you type here will be the name of the connection you are creating lt Back Cancel 7 13 OnCell G2100 Series User s Manual GPRS Connection 6 Enter 99 1 for the phone number and click Next New Connection Wizard Phone Number to Dial What ig your SF s phone number Type the phone number below Phone number qo You might need to include a 1 or the area code or both IF you are not sure you need the extra numbers dial the phone number on pour telephone IF you hear a modem sound the number dialed ts correct lt
27. a nn SS AA EII 2 a KA a a A y r A gt oo A M S A OnCell G2100 Series User s Manual Getting Started ATTENTION Grounding and wire routing help limit the effects of noise due to electromagnetic interference EMI There are two grounding points for the unit One point is the 3 pin terminal block connector for power Underneath the bottom mounting appendage is another grounding point For DIN rail mounted units Ground the DIN rail itself The modem s grounding point under the mounting appendage will be in direct contact with the rail Be sure to ground the DIN rail before connecting the modem to the DIN rail For wall or panel mounted units Run a ground wire from the right most pin of the terminal block connector Be sure to connect the ground wire before connecting devices to the modem 2 7 OnCell G2100 Series User s Manual Getting Started Wall Mounting Follow the intructions below to mount the OnCell Series modem on a wall STEP 1 STEP 2 Remove the 3 pin power terminal block For Use a flat blade screw driver to pull out both the OnCell G2150I also remove the 5 pin the top and bottom mounting appendages RS 422 485 terminal block
28. ame Serial Interac M Modify Baud Rate fiisz0o r Flow Control None Data Bits E Stop Bits ph Parity None Disable Echo i jis nh Sig Strength SIM Card PIN Setup IF your SIM card requires a PIN enter it here m Set Defaults 4 Select the appropriate COM port and communication parameters for connecting to the modem and click OK to proceed Connect Setup x Connection Setu COM Port Com Flow Control Hone Baud Aate fi 15200 Data Bits Stop Bits Parity A ATTENTION If you are not sure which communication parameters you should use please select the Auto Detect Serial Settings option and follow the onscreen instructions The procedure may take few minutes to complete When using the Auto Detect Serial Settings function if the GSM or the GPRS LED is ON or blinking you must remove the SIM card or use the escape command on the terminal to disconnect the current connection The default parameters are 115200 8n1 and RTS CTS flow control 3 37 OnCell G2100 Series User s Manual OnCell Configurator 5 Wait a few seconds for the default settings to load and click OK to finish Reset Modem To Defaults Beginning MERA OnCell Configurator X Default settings have been applied 115200 8 N 1 On recent hardware revisions of the OnCell G2100 Series modem default settings can be restored using the reset but
29. and mode or in on line mode When first powered up the modem will enter command mode The modem will only accept commands when it is in command mode Commands that are received when the modem is in on line mode are treated as data not as commands Commands may be entered from terminal software such as Windows HyperTerminal or Moxa PComm Lite Terminal Emulator Settings made with AT commands are automatically reused by the modem until another command is received to change the settings or the modem is turned off All but two of the commands must begin with the characters AT The two exceptions are the escape sequence and the repeat command A The command line prefix letters AT and the command sequences that follow can be entered in upper case or lower case but the cases must not be mixed More than one command can be typed on one line and commands can be separated by spaces to make them easier to read The spaces are ignored by the modem s command interpreter The command line buffer accepts up to 39 characters including A and T Spaces carriage returns and line feed characters are not placed in the buffer and do not count towards the 39 character limit If more than 39 characters are entered or if a syntax error 1s encountered in the command sequence the modem returns an ERROR result code and the command input is ignored The modem will acknowledge most commands almost immediately As soon as you type in a command e
30. answer on C Command Mode AUE Get Settings Hang Up Select Ban C GSM Autobauding C S50MHz C 900MHz G5M lt gt G5M 1800MHz 1900MHz ee Upgrade Fy mn Set Default 110 3600 GSM lt gt 15DM 850 17 900MHz f 900 1800MHz G5M lt gt 4nalog Modem 900 1900MHz 5 5 6 Using Short Message Services GSM technology offers the benefit of using SMS short message service as an easy way to communicate over the mobile network In this chapter we explain how to use SMS with the OnCell G2100 Series modem The following topics are covered in this chapter Sending Short Messages Reading Short Messages Deleting Short Messages SMS Tunnel Mode OOOO OnCell G2100 Series User s Manual Using Short Message Services Sending Short Messages Follow these instructions to send a short message to a specific phone number 1 Type AT CMGF 1 and press Enter 2 Type AT CMGS lt phone number gt and press Enter The terminal will present a gt prompt Enter your message at the prompt 3 Press Ctrl Z to deliver the message ES PComm Terminal Emulator COM1 115200 None 6 1 0umb Terminal Profile Edit Port Manager Window Help el BA alale 520 ES COM1 1152700 None 3 1 0umb Terminal Press Ctrl Z here DE at omgs O092 28 73951 SMS Test fl A ATTENTION AT CMGF 1 sets the SMS to Text mode Reading Short Messages Follow these instructions to rea
31. ation blank the OnCell G2100 Series modem will allow all incoming short messages to be forwarded to the attached serial device This includes system broadcasts and advertisements Once the SMS Tunnel SMS OUT SMS IN or both is activated and the SIM has registered to a carrier the GSM LED will start blinking The mode will be Data Mode which does not allow users to enter AT Commands If necessary use the escape command from the terminal to switch to Command Mode Command Mode allows the use of AT commands or OnCell Configurator SMS Tunnel Mode will disable auto answering and connections by GSM CSD and GPRS The timeout between characters is 0 5 seconds Messages that require a longer time period will be split into 2 or more messages 5 The complete profile will be displayed in Configurator Click Apply to save the settings onto the modem 2 OnCell Configurator Ioj xj File Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel lit Strings M SMS IN M SMS OLIT K Apply SMS to Seria Serial to SMS Caller ID Verification Target Phone Number e T Get Settings ML No 1 886891 91230 Mo 1 886891 91230 Ho Ho p ite ahh Sig Strength 6 8 The following topics are covered in this chapter O GPRS Overview O Windows GPRS Access gt VV Y Installing Modem Driver Modem Diagnostics Setting up the APN Adding Windows DUN Entr 7 GPRS Connection OnCell G2100 Series User s Manua
32. ce Device Nam I Modify MOXA TECHNOLOGY Baud Rate 118200 Flow Control g ow Control None dej Sig Strength Data Bits E SIM Card PIN Setup IF your SIM card requires a PIN Tem A pele Pw Stop Bits fi enter it here oono Parity None r Set Defaults Disable Echo The following instructions illustrate how to load a profile using the Wizard 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 3 27 OnCell G2100 Series User s Manual OnCell Configurator 2 Start OnCell Configurator and select the Load an existing Configuration file to Configurator option 2 OnCell Configurator Welcome to the OnCell Modem Wizard Use this wizard to set up pour OnCel G2700 cellular modem Create a Configuration File Create a new Configuration File from Configurator Load a Configuration Fil Load an existing Configuration File to Configurator Nent Cancel 3 Select a folder and profile and click Open Look in E Desktop de Ez My a Documents er E My Documents 3 My Computer My Network Places APP PIC Froduct Software G21501_5ave_01 txt s e My Netaark File name 621 AOL Save_O1 txt Y Places Files of type Tat files Ext bl 3 28 OnCell G2100 Series User s Manual 4 OnCell Configurator
33. ce may not cause harmful interference and 2 This device must accept any interference received including interference that may cause undesired operation
34. cel Initial Strings The following instructions illustrate how to configure the initial strings using Configurator 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 2 Start OnCell Configurator and select the Create a new Configuration File from Configurator option 2 OnCell Configurator x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modem Load 4 Configuration File Load an existing Configuration File to Configurator E Cancel 3 17 OnCell G2100 Series User s Manual OnCell Configurator 3 On the Init Strings tab enter the initial string in the text input box 2 OnCell Configurator Ioj x Fie Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings Separate 47 Comman Command 1 ATEO Command 2 arso 1 O Command 3 AT CICB 0 0 Command 4 ATAwMBS 4 Command 5 el Upgrade Fi Initial String eee ATEWEF O r Set Defaults O T bret ATTENTION p Appl if Get Settings the r ipai a l Sig Strength A maximum of 39 characters 1s allowed for each initial string Saving the Configuration Profile The following instructions illustrate how to configure the serial communication parameters using Configurator 1 Connect the RS 232 port of the OnCell G2100 S
35. cept the agreement lt Back Cancel 5 Click Next to proceed Mh Setup OnCell Configurator i Information Please read the following important information before continuing When you are ready to continue with Setup click Next OnCell 615016110 Wer 1 1 The OnCell Configurator for Moxa G27 50162110 setup To install the package under Windows 2000 P 2003 15 74 simply run Onell Configurator ese in the Onell 615016110 software diskette Back Cancel OnCell G2100 Seriesl User s Manual OnCell Configurator 6 Click Next or browse to a proper folder to proceed i B Setup OnCell Configurator a Select Destination Location Where should OnCell Configurator be installed C Program Files kosa OnCell 7 Click Next to proceed Th Setup OnCell Configurator Select Start Menu Folder Where should Setup place the program s shortcuts OnCell Configurator 3 5 OnCell G2100 Seriesl User s Manual OnCell Configurator 8 Click Next to proceed i G Setup OnCell Configurator Select Additional Tasks Which additional tasks should be performed 9 Click Install to start the software installation Th Setup OnCell Configurator Ready to Install Setup is now ready to begin installing OnCell Configurator on your computer OnCell G2100 Seriesl User s Manual OnCell Configurator 10 Wait until the installation is complete a Setup OnCell Configurator Installing Please wait while
36. com1 115200 None 8 1 Dumb Terminal lore ETE A ATTENTION Check the SIGNAL LED indicators on the front panel of the OnCell G2100 Series modem If the LEDs are all off then the SIM card is not installed properly or there is no signal present If only one LED is illuminated then the signal is not strong enough to create a CSD connection Adjust the position of the antenna change the location of the modem or use an optional high gain antenna Verify that your SIM card has CSD service activated For most regions you must apply with your mobile service provider to receive this service Verify that the RS 232 port on the OnCell G2100 Series modem is connected For the OnCell G21501 verify that DIP switch 1 is set to ON 5 2 OnCell G2100 Series User s Manual GSM CSD Connection 2 Type ATD lt phone number gt and press Enter For example type ATD 0289191230 if the phone number is 0289191230 3 Check the GSM indicator on the front panel of the modem If the LED is on and an amber color the CSD connection has been established successfully You can switch to data mode to proceed with data communication 4 Toclose the CSD connection type The modem will respond with OK to indicate that you have already switched back to the command mode 5 Type ATH and press Enter to disconnect ES PComm Terminal Emulator COM1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help el BA alale 32
37. d a short message that was sent to the OnCell Type AT CMGF 1 and press Enter 2 When a short message is received the modem will respond with a storage number for the message The storage number will appear as CMTI SM x where x is the storage number 3 Type AT CMGR x to read the message where x is the storage number of the message 6 2 OnCell G2100 Series User s Manual Using Short Message Services In the example the storage number is 5 which means that the message is stored in the 5 storage location ES PComm Terminal Emulator COM1 115200 None 6 1 0umb Terminal Profile Edit Port Manager Window Help al Al alela 52 E com1 115200 None 8 1 Dumb Terminal CHTI 2sn 5 ttemgr 5 CHGE REC UNREAD 886972613404 O7SO3 19 00 36 24 352 SMS Test 1 DE Deleting Short Messages Follow these instructions to delete a short message 1 Type AT CMGD x n and press Enter For x select one of the following options REC UNREAD Shows received unread messages REC READ Shows received read messages STO UNSENT Shows stored unsent messages STO SENT Shows stored sent messages ALL Shows messages For n select one of the following options Delete message at location lt include the index number gt Delete all READ messages Delete all READ and SENT messages Delete all READ SENT and UNSENT messages Delete ALL messages REC UNREAD Shows received unread messages
38. d the installation file on the Document and Software CD The installation file will be located in the Configurator directory and will be named OnCell_Configurator_Install_1 1 exe or something similar Ze Double click the installation file y Onell Configurator Install 1 1 e gt Onell Configurator setip et Moxa Company Inc 3 Click Next to proceed Mh Setup OnCell Configurator Ioj x Welcome to the OnCell Configurator Setup Wizard This will install Onell Configurator on your computer lk is recommended that you close all other applications before continuing Click Nest to continue or Cancel to exit Setup Cancel 3 3 OnCell G2100 Series User s Manual OnCell Configurator 4 Choose I accept the agreement and click Next Mh Setup OnCell Configurator J License Agreement Please read the following important information before continuing Please read the following License Agreement ou must accept the terms of this agreement before continuing with the installation End User License Agreement Before installing the Onell 6150162170 you must agree to Moxa s End User Product License Agreement Please read through this license agreement carefully IF You do not agree to them please DO NOT install the software Subject to the following terms and conditions Moxa Technologies Co Ltd Mosa grants to you User a non exclusive license to use the enclosed software do not ac
39. de Back Hent Cancel ATTENTION Transparent Mode provides the general functions of a GSM GPRS modem 4 Onthe SMS Tunnel Mode Settings page select SMS IN to forward incoming short messages to the attached serial device Select SMS OUT to transmit serial data from the attached serial device as SMS messages The Caller ID Verification phone number and Target Phone Number should be specified Click Next to proceed 2 OnCell Configurator y x SMS Tunnel Mode Settings SMS Data Mode creates a data tunnel for low speed and non tine critical applications to send data over SMS service provided by a carrier V SMS IN 4 SMS OUT SMS to Seria Serial to SMS Caller ID Verification Target Phone Number Not 88689191230 Not 88689191239 Ho p Hoe p SMS Data Format SMS Data Format Text ASCII Text ASCII Binary 8 bits Binary 8 bits Unicode UCS2 C Unicode UCS2 Back Hent Cancel 6 7 OnCell G2100 Series User s Manual Using Short Message Services SMS Data Format Text ASCII 7 bits text format 160 bytes per packet 8 bits binary 140 bytes per packet 16 bits Unicode UCS2 format 70 bytes per packet ATTENTION The Target Phone Number must be specified if SMS OUT is activated The Target Phone Number and Caller ID Verification must be written in international format starting with followed by the country code If you leave Caller ID Verific
40. disk click Have Disk Manufacturer Models sf This driver is digitally signed Tell me why driver signing ls important lt Back Cancel 4 When the Install From Disk window opens click Browse Install From Disk q x fea Insert the manufacturer s installation disk and then OK al make sure that the correct drive is selected below De Cancel Copy manufacturer s files From C ese D 5 Select the OnCell_G2100_Series inf driver The file is located in the Win_Driver directory on the Document and Software CD Click Open to proceed Locate eS Look ir E Win Driver a y pe file 2 FONCell G2100 Series File name ONCed_62100_series OnCell G2100 Series User s Manual GPRS Connection 6 When the Install From Disk page opens click OK Install From Disk al Insert the manufacturer s installation disk and ther ail make sure that the correct drive is selected below Copy manufacturer s files From D vafin_Driver a 7 Click Next Add Hardware Wizard Install New Modem a Select the manufacturer and model of pour modem If your modern is not listed or if you have an installation disk click Have Disk Mosa OnCell 62100 Seres GSM GPRS Modem ity This driver is not digitally signed Have Disk Tell me why driver signing ls important lt Back Cancel 7 5 OnCell G2100 Series User s Manual GPRS Connection 8 When the next window opens
41. e escape command from the terminal to switch to Command Mode Command Mode allows the use of AT commands or OnCell Configurator SMS Tunnel Mode will disable auto answering and connections by GSM CSD and GPRS The timeout between characters is 0 5 seconds Messages that require a longer time period will be split into 2 or more messages The following instructions show how to configure SMS Tunnel mode using the Wizard 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch is set to ON 2 Start OnCell Configurator and select the Create a new Configuration File from Wizard option x Welcome to the OnCell Modem Wizard Use this wizard to set up your OnCell 62100 cellular modern Create a Configuration File Create a new Configuration File fron Configurator a Create a new Configuration File from Wizard j Load a Configuration File Load an existing Configuration File to Configurator Hent Cancel 6 6 OnCell G2100 Series User s Manual Using Short Message Services 3 Select SMS Tunnel Mode and click Next to proceed 2 OnCell Configurator xj Welcome to the OnCell Modem Wizard Use this wizard to set up your OnCell 62100 cellular modern Please select mode that you would like set up fect an Operation Mode Transparent Mode Modem is fully controlled by AT Commands in Transparent Mo
42. e limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instructions may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user 1s encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help CAUTION Any changes or modifications not expressly approved by the grantee of this device could void the user s authority to operate the equipment FCC RF Radiation Exposure Statement This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled environment This equipment should be installed and operated with a minimum distance of 20cm between the radiator and your body This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This devi
43. ediately You will need to update your terminal settings to match any changes in the serial communication parameters Configuration can also be performed with the AT SERIAL command or OnCell Configurator The default serial communication parameters are 115200 bps 8 data bits None parity RTS CTS flow control and 1 stop bit Before changing the settings first connect the RS 232 port of the OnCell G2100 Series modem to a host PC Open PComm Terminal Emulator with the current communication parameters Modifying Baudrate 1 Type AT IPR x and press Enter where x corresponds to one of the following baudrates 300 600 1200 2400 4800 9600 19200 38400 57600 115200 0 autobauding For example type AT IPR 9600 to change the baudrate to 9600 bps ES PComm Terminal Emulator COM1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help el BA alale 32 E com1 115200 None 8 1 Dumb Terminal 2 Modify the terminal settings to match the new serial communication parameters IM x Communication Parameter Terminal File Transfer Capturing COM Options Forts Baud Rate Data Bits Parity Stop Bits Flow Control M RATSACTS DTA ON OFF ONOFF ATS ON OFF Cancel 4 10 OnCell G2100 Series User s Manual AT Command Set 3 Type AT amp W and press Enter to save the settings ES PComm Terminal Emulator COM1 9600 None 3 1 0umb Terminal
44. em type The modem will respond with OK which means that you have already switched back to command mode Type ATH and press Enter to disconnect 5 4 OnCell G2100 Series User s Manual GSM CSD Connection A ATTENTION ATA is the answer command ATSO lt x gt is the auto answer command The AT amp W command saves the current settings to the modem It is much easier to configure auto answer with OnCell Configurator On the GSM Setting tab select Enable Auto answer on ___ Rings and enter the desired number of rings icxi Fie Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings GSM Connection OTRA Drop Action Ignore DTA W Enable Auto answer on C Command Mode ae Get Settings TZ Rings Hang Up ATTENTION If you are answering a call from a PSTN dial up modem type AT CICB 0 to force the incoming call to be a data call Type AT CBST 7 0 1 to select bearer type to V 32 modem 9600 bps In addition type AT amp W to save the settings For further information please refer to the OnCell G2100 Series AT Commands Guide on the Document and Software CD This task can be performed easily in OnCell Configurator Select the V32 9600 option and click Apply to activate the function 2 OnCell Configurator ioj xj File Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings BSM Connectio DTA Drop Action Ignore DTA W Enable Auto
45. er understanding of how to use the AT Commands A ATTENTION Make sure that the RS 232 port of the OnCell G2100 Series modem is connected For the OnCell G2150L make sure DIP switch 1 is set to ON Modem Acknowledgement Connect the RS 232 port of the OnCell G2100 Series modem to a host PC Start PComm Terminal Emulator with the current communication parameters default 115200 bps 8 data bits None parity 1 stop bits and no flow control Type AT and press Enter A modem response of OK indicates that the modem 1s ready ES PComm Terminal Emulator COM1 115200 None 8 1 Dbumb Terminal Profile Edit Port Manager Window Help al all alaale 3 28 E com1 115200 None 8 1 Dumb Terminal Verify Signal Strength Connect the RS 232 port of the OnCell G2100 Series modem to a host PC Open PComm Terminal Emulator with the current communication parameters default 115200 bps 8 data bits None parity 1 stop bits and no flow control Type AT CSQ and press Enter The modem will respond with the receive signal strength RSSI and channel bit error rate BER ES PComm Terminal Emulator COM1 115200 Mone 8 1 bumb Terminal Profile Edit Port Manager Window Help el BA alale 228 E com1 115200 None 8 1 Dumb Terminal OnCell G2100 Series User s Manual AT Command Set Signal Strength Verification 0 to 12 Weak or insufficient BER ranges from 0 to 7 with 7 corresponding to a higher error rate A ATTENTION
46. eries modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 2 Start OnCell Configurator and select Create a new Configuration File from Configurator 2 OnCell Configurator X Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modern Load 4 Configuration File Load an existing Configuration File to Configurator E Cancel 3 18 OnCell G2100 Seriesl User s Manual 3 4 OnCell Configurator Select Save File from the File menu OnCell Configurator File Terminal Emulator Help Go to Mode Wizard gl SMS Tunnel nit Strings Device Nam 26 Apply MOXA TECHNOLOGY Load File From Exit Baud Aate Get Settings hoses Select a folder and enter the file name for the profile Click Save sa ex FE My Recent My Network Places Documents app ri PIC Product Software Desktop Share_Pic v1 0cD My Documents pa Sr My Computer My Network Places File name 621 AOL Save_O1 Text Files txt Me Save as lype 3 19 OnCell G2100 SeriesI User s Manual OnCell Configurator Applying Modem Settings The following instructions illustrate how to apply the current settings to an OnCell G2100 Series modem using Configurator 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is c
47. esl User s Manual OnCell Configurator 3 On the Configure the Serial Interface page click Modify and configure the serial device settings Enter the device name in the text input box OnCell Configurator Gg Configure the Serial Interface Set up new serial communication parameters 115200 Di 08 TECHNOLOGIY Me Y e of i Nowe SS 3 12 OnCell G2100 Series User s Manual OnCell Configurator Configuring the PIN Setting The following instructions explain how to configure the PIN code using Configurator 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 2 Start OnCell Configurator and select the Create a new Configuration File from Configurator option 42 OnCell Configurator x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modem Load 4 Configuration File Load an existing Configuration File to Configurator 3 On the Basic Setting tab and enter the correct PIN in the text input box 2 OnCell Configurator Ioj xj File Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings Device Name dl Get Settings tt A pl i Sig Strength Serial Interac Modify Baud Rate fiis200 Flow Control None Data Bits Bo x Stop Bits ph Parity None Disable Echo SIM Card PIN Setup AH Upgrade Fy Ld
48. evice Name 4 Modify Baud Rate 118200 Flow Control Hone MOKA TECHNOLOG z 4i biel Get Settings fi i inh oh fh Sig Strength SIM Card PIN Setup Data Bits lb H Stop Bits hr Parity None IF your SIM card requires a PIN enter it here r Set Defaults b fee 3 10 OnCell G2100 Series User s Manual A ATTENTION Use the command AT IPR 0 to enable Autobauding Please refer to Chapter 4 for details Autobauding and the escape command only work with 8n1 and e71 settings Using other settings will disable these functions Stop bits can only be set to 2 only when parity is set to none The default parameters are 115200 8n1 and RTS CTS flow control The following instructions explain how to configure the serial communication parameters using Wizard l Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON Start OnCell Configurator and select the Create a new Configuration File from Wizard option 2 OnCell Configurator x Welcome to the OnCell Modem Wizard Use this wizard to set up your OnCel G2700 cellular modem Create a Configuration File Create a new Configuration File from Configurator Load 4 Configuration File Load an existing Configuration File to Configurator Nent Cancel 3 11 OnCell Configurator OnCell G2100 Seri
49. features 0 Transparently converts serial data to short message or vise versa without using AT Commands Text binary and Unicode formats are supported e Verification of Incoming Caller ID is implemented to block uncertified users The configuration profile can be easily stored and copied to other modems E The following instructions explain how to use Configurator to configure SMS Tunnel Mode j SMS Tunnel LED Panel 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 2 Start OnCell Configurator and select the Create a new Configuration File from Configurator option 2 OnCell Configurator gz x Welcome to the OnCell Wizard Use this wizard to set up pour OnCell G2100 cellular modem Eate a Configuration File Create a new Configuration File from Configurator Create a new Configuration File from Wizard Load a Configuration Fil Load an existing Configuration File to Configurator E Cancel 6 4 OnCell G2100 Series User s Manual Using Short Message Services 3 Onthe SMS Tunnel tab select SMS IN to forward incoming short messages to the attached serial device Select SMS OUT to transmit serial data from the attached serial device as SMS messages The Caller ID Verification phone number and Target Phone Number should be specified e0
50. gurator OmCell Configurator Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modern f Create a new Configuration File from Configurator D tegale a ME COTTA a m wear Load a Configuration Fil Load an existing Configuration File to Configurator 3 Click Upgrade FW on the right side of the window 2 OnCell Configurator File Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings Device Name A Serial Interac Modify Baud Rate fiisz00 Flow Control None Data Bits EE Stop Bits ph Parity Hone 7 fis AKE g i 1 Sig Strength SIM Card PIN Setup IF your SIM card requires a PIN enter it here Disable Echo 4 Upgrading the firmware will clear all current configuration settings in the OnCell G2100 Series modem To exit and save the current settings click NO To proceed click Yes OnCell Configurator l x This will reset the modern to default settings Your current settings will be lost To save your modermn s current settings press Cancel then use the Get Settings Function and the File Sawe command Do vou wish to proceed 3 33 OnCell G2100 Series User s Manual OnCell Configurator 5 Selecta firmware file from the disk and click Open to proceed Look ir E Desktop do fee My Recent Documents E eS k ho p My Documents A SE My Computer
51. h the RS 232 and RS 422 485 interfaces come with two types of protection 1 2 5 KV RMS isolation for 1 min and 2 15 KV ESD serial line protection T T R D R D GND RS 422 485 settings are configured by DIP switch on the bottom panel e Switches 1 2 and 3 select the serial interface e Switch 4 enables or disables the termination resistor e Switches 5 and 6 set the pull high low resistor 2 10 OnCell G2100 Series User s Manual Getting Started RS 422 ON Termination Resistor SW4 Enabled Disabled LED Indicators GSM PWR GPRS DATA Name Color Function eusi Signal level data transmission requires at least 2 bars Green DC power connection GSM Aabe ae GSM CSD pOnnecied Blinking SMS Tunnel is enabled registered to a carrier GPRS Amber GPRS connected DATA Green Serial Tx Rx 1 bar Weak or insufficient signal SMS only Exceptional signal GSM CSD and GPRS connections 3 OnCell Configurator Most modems are configured using AT commands Moxa s OnCell Configurator provides an easy and convenient alternative to configure the OnCell 2100 Series modem This chapter covers the following topics Overview Installing OnCell Configurator Launching OnCell Configurator Configuring Serial Connection and Device Name Configuring the PIN Setting Configuring the Radio Band Initial Strings Saving the Configuration Profile Applying Modem Settings Retrieving the Modem Setti
52. he GPRS LED is ON or blinking you must remove the SIM card or use the escape command on the terminal to disconnect the current connection The default parameters are 115200 8n1 and RTS CTS flow control 3 31 OnCell G2100 Series User s Manual OnCell Configurator 5 Wait a few moments for the signal strength and the carrier information to be queried Click OK to finish 7 Monitor Signal Strength Jo xj Update Frequenc f 5Sec 10Sec 30Sec Network GSM Operator TV Mobile Registration Registered Ax Leve RSSI 21 Upgrading the Firmware The following instructions illustrate how to use Configurator to upgrade the firmware of an OnCell G2100 Series 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON A ATTENTION The RS 232 connector uses the standard pinouts A direct male DB9 to female DB9 cable such as Moxa s CBL F9M9 150 100 cm or CBL F9M9 20 20 cm can be used to connect to a PC s serial port If you use a USB to serial product to configure the OnCell G2100 Series modem we strongly recommend using Moxa s UPort 1110 Other USB to serial products may cause unexpected errors when configuring the OnCell G2100 Series modem 3 32 OnCell G2100 Series User s Manual OnCell Configurator 2 Start OnCell Configurator and select Create a new Configuration File from Confi
53. hich communication parameters you should use please select the Auto Detect Serial Settings option and follow the onscreen instructions The procedure may take few minutes to complete When using the Auto Detect Serial Settings function if the GSM or the GPRS LED is ON or blinking you must remove the SIM card or use the escape command on the terminal to disconnect the current connection The default parameters are 115200 8n1 and RTS CTS flow control 3 24 OnCell G2100 Series User s Manual OnCell Configurator 5 Wait a few moments for the settings to be retrieved Click OK when prompted Get settings from modern OnCell Configurator x Query modem status sucess 6 The settings will be displayed in the Configurator window The current firmware version will also be displayed OnCell Configurator Ioj x Fie Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings Senal Interface Device Name Apply Iv Modify MOXA TECHNOLOGY ii Baud Rate 115200 ad Get Settings Fl E t i ii i GEE None E Siig Sig Strength Data Bits E SIM Card PIN Setup Stop Bits O IF your SIM card requires a PIN rra fees AH Upgrade Fis enter it here r Set Detaults as eee Parity None Disable Echo i Fi Wer 1 2 Build 07053002 3 25 OnCell G2100 Series User s Manual OnCell Configurator Loading a Profile The following instructions illust
54. ing ES PComm Terminal Emulator COM1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help el Bika a gt 32 ES COM1 115200 None 8 1 0umb Terminal PIN Code Management Operation of the OnCell G2100 Series modem requires the installation of an active SIM Subscriber Identity Module card The SIM card contains the necessary data to identify the modem to the network service provider It 1s also used to store the GSM GPRS modem PIN Personal Identification Number and PUK Personal Unblocking Key which are also used with mobile phones The PIN helps prevent unauthorized persons from using the mobile devices Users must enter the PIN each time the modem is powered up The PUK is used to unlock a SIM card when an incorrect PIN code has been entered three times Query the Current PIN Status 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC Start PComm Terminal Emulator with the current communication parameters default 115200 bps 8 data bits None parity 1 stop bit and no flow control 2 Type AT CPIN and press Enter ES PComm Terminal Emulator COM1 115200 None 8 1 Dbumb Terminal Profile Edit Port Manager Window Help el BA alale 228 EA com1 115200 None 8 1 Dumb Terminal lars attcpin CPIN SIM PIN If the OnCell G2100 Series modem responds with CPIN SIM PIN then the user must enter the SIM s PIN code AT CPIN responses CPIN READY Modem is not pendi
55. ion Setu COM Fort Com Flow Control Hone Baud Aate fi 15200 Data Bits Stop Bits Parity OF Cancel ATTENTION If you are not sure which communication parameters you should use please select the Auto Detect Serial Settings option and follow the onscreen instructions The procedure may take few minutes to complete When using the Auto Detect Serial Settings function if the GSM or the GPRS LED is ON or blinking you must remove the SIM card or use the escape command on the terminal to disconnect the current connection The default parameters are 115200 8n1 and RTS CTS flow control 3 21 OnCell G2100 Series User s Manual OnCell Configurator 5 Wait a few moments for the settings to be applied Click OK to finish Ss eee Apply new settings to modern Loading TTT OnCell Configurator E x Modem settings have been applied 3 22 OnCell G2100 SeriesI User s Manual OnCell Configurator Retrieving the Modem Settings The following instructions illustrate how to use Configurator to get the current settings of an OnCell G2100 Series modem 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON A ATTENTION The RS 232 connector uses the standard pinouts A direct male DB9 to female DB9 cable such as Moxa s CBL F9M9 150 100 cm or CBL F9M9 20 20 cm can be used
56. ire and common wire Observe all electrical codes dictating the maximum current allowable for each wire size If the current goes above the maximum ratings the wiring could overheat causing serious damage to your equipment Temperature Caution Be careful when handling the device When plugged in the device s internal components generate heat and the casing may feel hot to the touch You should also pay attention to the following guidelines e Use separate paths to route wiring for power and devices If power wiring and device wiring paths must cross make sure the wires are perpendicular at the intersection point NOTE Do not run signal or communication wiring and power wiring in the same wire conduit To avoid interference wires with different signal characteristics should be routed separately e Use the type of signal transmitted through a wire to determine which wires should be kept separate Generally if different wires share similar electrical characteristics they can be bundled together e Keep input wiring and output wiring separate e If possible it is recommended that all device wiring be clearly labeled 2 4 OnCell G2100 Series User s Manual Getting Started SIM Card Installation In order to protect the SIM card the SIM card slot is located inside the casing You will need to unscrew and remove the outer cover before installing or removing the SIM card SIM Cover Follow these steps to remove or insta
57. ke sure that the RS 232 port of the OnCell G2100 Series modem is connected For the OnCell G2150L make sure DIP switch 1 is set to ON 1 From the Control Panel open Phone and Modem Options On the Modem tab click Properties Phone and Modem Options l x Dialing Rules Modems Advanced The following modems are installed Be Attached To lt A Moxa On Cell G2110 Series GSM GPRS COM Froperties D p OK Cancel Apply 7 10 OnCell G2100 Series User s Manual GPRS Connection 2 On the Advanced tab enter the following in the Extra initialization commands field AT CGDCONT 1 IP lt APN gt For lt APN gt use the correct service for your account as in this example AT CGDCONT 1 IP ISP CINGULAR Moxa OnCell G2100 GSM GPRS M Draperties ax General Modem Diagnogtics Advanced Dri Estra Settings Extra initialization commands AT CGOCONT 1 1P 15P CINGULSA A ATTENTION The APN should be entered between the displayed brackets Remember that the APN is case sensitive Note that IP should be written in all capital letters For a list of APNs please refer to the APN List on the Document and Software CD 3 Click OK to close the Properties window OnCell G2100 Series User s Manual GPRS Connection Adding Windows DUN Entry The following instructions explain how to add a Windows Dial up Networking entry In the Control Panel open Network Connection
58. l GPRS Connection GPRS Overview GPRS 1s a packet switched technology which means that multiple users share the same transmission channel In addition transmission only occurs when there is outgoing data This means that the available bandwidth can be dedicated solely to data communication as needed In general a GPRS network can be viewed as a special IP network that offers IP connectivity to IP terminals Devices such as PCs embedded computers and PLCs that are PPP enabled can be easily connected to the IP network and the Internet 39 Central GPRS PPP Eabled PC Contriler The OnCell G2100 Series modem is a multi slot Class 10 device which means that there are 4 Rx timeslots plus 1 Tx timeslot or 3 Rx timeslots plus 1 Tx timeslot This requires that the provider support CS 1 to CS 4 coding schemes GPRS offers no guaranteed data rates or bandwidth The value assigned by the provider coding scheme and timeslots can change dynamically during a connection In general for the 1 Tx 4 Rx combination the Tx throughput is around 8 to 12 Kbps and the Rx throughput is around 32 to 48 Kbps For the 2 Tx 3 Rx combination the Tx throughput 1s around 8 to 12 Kbps and the Rx throughput is around 32 to 48 Kbps Windows GPRS Access The OnCell G2100 Series modem can use Windows DUN Dial up Networking to provide Internet access through the GPRS mobile network The following pages explain how to configure the modem and your Windows system
59. l disable these functions 2 stop bits are only allowed with None parity 4 12 OnCell G2100 Series User s Manual AT Command Set Flow Control The default RTS CTS flow control setting 1s none Follow these steps to enable flow control 1 Type AT ICF 2 2 and press Enter To disable flow control again type AT ICF 0 0 and press Enter ES PComm Terminal Emulator COM1 9600 Even 7 1 Dumb Terminal Profile Edit Port Manager Window Help al HH Elala X28 ES com1 9600 Even 7 1 Dumb Terminal 2 Type AT amp W and press Enter to save the settings A ATTENTION Changes to the serial communication parameters take effect immediately You will need to update your terminal settings to match any changes in the serial communication parameters XON XOFF flow control is not supported 2 wire RS 485 Communication OnCell G21501 Only 2 wire RS 485 is half duplex communication For this reason the modem s local echo should be disabled Follow these steps to disable local echo A ATTENTION The local echo function can also be disabled using OnCell Configurator 1 On the bottom of the modem set DIP switch 1 to ON 2 Connect the modem s RS 232 port to a host PC Start PComm Terminal Emulator with the current communication parameters default 115200 bps 8 data bits None parity stop bits 3 Type ATEQ and press Enter to disable the local echo 4 13 OnCell G2100 Series User s Manual AT Command Set 4 T
60. ll the SIM card l Unscrew the outer cover Zi Slide the outer cover to the left to remove it 3 Slide the SIM card cradle to the left and pull it towards you Insert the SIM card into the cradle 4 Swing the cradle back against the unit and slide it back into place Replace the outer SIM card cover A ATTENTION The SIGNAL LEDs on the front panel provide a convenient way of checking if the SIM card is installed properly One of the three SIGNAL LEDs should remain on as long as the antenna is installed and the network is operating normally If none of the SIGNAL LEDs are on then the SIM card may not be installed properly Since the PIN code is stored on the SIM card the modem will not be accessible from the cellular network if the SIM card is not installed correctly DIN Rail Mounting Built in mounting appendages allow the modem to be mounted to a flat wall or on a DIN rail Follow the intructions below to mount the modem on a DIN rail A ATTENTION Before mounting the OnCell G2100 Series modem we strongly recommend that you first remove the antenna connection 2 5 OnCell G2100 Series User s Manual Getting Started STEP 1 STEP 2 Use a flat blade screw driver to pull the Hook the modem over the top edge of the bottom mounting appendage out It should DIN rail as shown snap into place should snap into place over the bottom edge of the DIN rail I ee i IMMO N aan nn gt 5 NY gt
61. nCell Configuator o File Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel lr Strings Apply a his Get Settings M SMS IN lf SMS OUT SMS to Seria Serial to SMS Caller ID Verification Ho 1 B86891 91230 No p SMS Data Format e Text ASCII Binary 8 bits Unicode UCS 2 Target Phone Number No 7 88689191230 Hoe p SMS Data Format Text ASCII Binary 8 bits C Unicode UCS2 r Set Defaults Put Wer 12 Build OFO53002 SMS Data Format Text ASCII 7 bits text format 160 bytes per packet Binary 8 bits binary 140 bytes per packet 16 bits Unicode UCS2 format 70 bytes per packet 6 5 OnCell G2100 Series User s Manual Using Short Message Services A ATTENTION The Target Phone Number must be specified if SMS OUT is activated The Target Phone Number and Caller ID Verification must be written in international format starting with followed by the country code If you leave Caller ID Verification blank the OnCell G2100 Series modem will allow all incoming short messages to be forwarded to the attached serial device This includes system broadcasts and advertisements Once the SMS Tunnel SMS OUT SMS IN or both is activated and the SIM has registered to a carrier the GSM LED will start blinking The mode will be Data Mode which does not allow users to enter AT Commands If necessary use th
62. nding with the carriage return character your modem will respond with OK A ATTENTION This is one of the two commands that do not use the AT prefix The 3 plus signs are used for the Escape Character Sequence After you have connected to another modem you may need to return to command mode to modify the modem s configuration or to hang up To do this leave your keyboard idle do not press any keys for at least one second and then press three times You do not need to press the Enter key After a moment the modem will respond with OK indicating that Command mode is now active 4 2 OnCell G2100 Series User s Manual AT Command Set Starting Moxa Terminal Emulator The following instructions explain how to install the Moxa PComm Lite Package After installing PComm Lite you can use the built in Moxa Terminal Emulator to handle your modem operations A ATTENTION OnCell Terminal Emulator is designed for Windows 2000 XP 2003 and Vista If you are running Windows 98 ME or NT use PComm Lite V2 6 which can be downloaded on the Moxa website l Ze gt Terminal Emulator is installed with OnCell Configurator Please refer to Chapter 3 for details Start Terminal Emulator from the Windows Start menu Internet i My Documents Internet Explorer Fe My Recent Documents E mail Outlook Expres ey Set Program Access and Defaults Windows Catalog Windows Messe w windows Update fin Accessories
63. ng for any password CPIN SIM PIN PINI is required CPIN SIM PUK PUK1 is required If the OnCell G2100 Series modem responds with CPIN READY then the SIM security is disabled or the PIN for the SIM was entered correctly 4 7 OnCell G2100 Series User s Manual AT Command Set 3 Ifthe modem responds with CPIN SIM PIN type AT CPIN lt pin gt where lt pin gt is the correct PIN Press Enter The following example shows 0000 being entered for the PIN ES PComm Terminal Emulator COM1 115200 None 8 1 bumb Terminal Profile Edit Port Manager Window Help el BA alale 32 E com1 115200 None 8 1 Dumb Terminal A ATTENTION Be careful when entering the PIN codes After 3 unsuccessful attempts at entering the PIN you will need to use the PUK to proceed PUK validation forces the user to enter a new PIN code as a second parameter and this will be the new PIN code if PUK validation succeeds CHV1 will be enabled if PUK1 is correct Therefore the application uses the following command AT CPIN lt PUK gt lt NewPIN gt Note that users must apply for PUK codes from the mobile service provider Disable the Facility Lock Disabling the facility lock will allow the OnCell G2100 Series modem to operate without entering the PIN code each time the modem is powered up 1 Type AT CPIN lt pin gt where lt pin gt is the correct PIN Press Enter 2 Type AT CLCK SC 0 lt pin gt where SC should
64. ngs Loading a Profile Signal Strength Monitor Upgrading the Firmware Setting Modem Defaults DOUUWUUOWOOOOUUUWUOOD OnCell G2100 Series User s Manual OnCell Configurator Overview OnCell Configurator is a PC based utility for managing and configuring your OnCell G2100 Series modem With 1ts Windows based graphical interface even first time users will find 1t easy to learn You can configure general settings modes and dial out parameters without any knowledge of the associated AT commands It is much more convenient than traditional methods of configuration that require users to search through a thick AT command reference manual OnCell Configurator also makes 1t more convenient to implement mass deployment or pre configuration eo An installation wizard provides step by step configuration of the modem e The configuration is easily stored and replicated on other modems Db remand Emte ii Base Setirg GSN Setting SMS Turrel int Sarg Sonal rimtace Dence Name Mody Badfiee firms F yous SIM cord gas a Configuration Profile Mass Deployment 3 2 OnCell G2100 Seriesl User s Manual OnCell Configurator Installing OnCell Configurator To install OnCell Configurator follow the instructions below After installation users will be able to use the Configurator Wizard and Terminal Emulator for further operations ATTENTION OnCell Configurator supports Windows 2000 XP 2003 and Vista 1 Fin
65. ns on how to install the OnCell G2100 Series modem The following topics are covered in this chapter LJ Product Characteristics LJ Dimensions gt OnCell G2150I gt OnCell G2110 G2110 T LJ Connecting the Hardware gt VV VVV V Wiring Requirements SIM Card Installation DIN Rail Mounting Connecting the Antenna Connecting Power Connecting a Serial Device LED Indicators OnCell G2100 Series User s Manual Getting Started Product Characteristics 12 48V DC Terminal Block H W RESET Button SMA Antenna Connector 9 DIN Wall Mount Kit 10 Protected SIM Cover Cellular Signal Level LED PWR GSM GPRS Data LED 11 Antenna Isolated RS 232Port 6 pin DIP Switch 621501 MOKA Isolated RS 422 485 Port G21501 only Dimensions OnCell G2150l1 89 30 3 516 76 00 2 992 123 00 4 843 141 50 5 571 O 27 00 1 063 2 2 OnCell G2100 Series User s Manual Getting Started OnCell G2110 G2110 T MM 1 1 Y 27 00 1 063 OnCell G2100 Series User s Manual Getting Started Connecting the Hardware This section describes how to connect the OnCell G2100 Series modem to a host PC or serial devices for initial testing and configuration Wiring Requirements A ATTENTION Safety First Be sure to disconnect the power cord before installing and or wiring your device Wiring Caution Calculate the maximum possible current in each power w
66. onnected and DIP switch 1 is set to ON ATTENTION The RS 232 connector uses the standard pinouts A direct male DB9 to female DB9 cable such as Moxa s CBL F9M9 150 100 cm or CBL F9M9 20 20 cm can be used to connect to a PC s serial port If you use a USB to serial product to configure the OnCell G2100 Series modem we strongly recommend using Moxa s UPort 1110 Other USB to serial products may cause unexpected errors when configuring the OnCell G2100 Series modem 2 Start OnCell Configurator and select the Create a new Configuration File from Configurator option x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modern Create a new Configuration File from Wizard Load a Configuration File Load an existing Configuration File to Configurator E Cancel 3 20 OnCell G2100 Series User s Manual OnCell Configurator 3 Click Apply 2 OnCell Configurator j Ioj x Fie Terminal Emulator Help Device Name a Get Settings Serial Interfac Modify Baud Rate fiisz00 Flow Control None Data Bits Bo x Stop Bits ph Parity None Disable Echo i beh a Sig Strength SIM Card PIN Setup IF your SIM card requires a PIN enter it here r Set Defaults See 4 Select the appropriate COM port and communication parameters for connecting to the modem Click OK to proceed Connect Setup x Connect
67. perature e OnCell G2150I industrial GSM GPRS modem RS 232 and RS 422 485 2 5 KV RMS isolation protection Package Checklist Product e OnCell G2100 Series industrial GSM GPRS modem Standard Accessories e Document amp Software CD 0 dBi magnetic mount SMA antenna Terminal block adaptor for power jack connector Warranty statement Quick Installation Guide NOTE Please notify your sales representative if any of the above items are missing or damaged Optional Accessories e Power adaptor e ANT CQB O 1 High gain antenna omni directional 1 dBi SMA rubber e ANT CQB O 3 3m High gain antenna 3 meters 3 dB1 25 cm magnetic mount SMA e ANT CQB O 5 3m High gain antenna 3 meters 5 dB1 37 cm magnetic mount SMA e CBL F9M9 150 Serial cable 100 cm DB9 female to DB9 male RS 232 e CBL F9M9 20 Serial cable 20 cm DB9 female to DB9 male RS 232 e UPort 1110 USB to serial adaptor RS 232 e Quad band GSM GPRS supporting 900 1800 MHz 850 1900 MHz e GPRS Class 10 supporting up to 14 400 bps in GSM CSD mode e SMS short message support e SMS Tunnel mode e 15 KV ESD serial line protection e LED indicators for signal status and level e P30 enclosure supporting DIN rail and wall mounting 1 2 OnCell G2100 Series User s Manual Introduction e Seperate RS 422 485 interface OnCell G2150I only e 2 5 KV RMS for 1 minute isolation for all serial signals OnCell G2150I only Specifications Cellular Comm
68. r option x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modern Se orniguration File f Create a new Configuration File from Configurator Create a new Configuration File from Wizard Load 4 Configuration File Load an existing Configuration File to Configurator E Cancel 3 30 OnCell G2100 Series User s Manual OnCell Configurator 3 Click the Sig Strength button on the right side of the window 2 OnCell Configurator File Terminal Emulator Help 15 x K Apply Serial Interac Device Name Modify Baud Rate fiiszoo Flow Control None Data Bits Bo x Stop Bits ph Parity None Disable Echo tine nh ales Sig Strength SIM Card PIN Setup IF your SIM card requires a PIN enter it here r Set Detaults 4 Select the appropriate COM port and communication parameters for connecting to the modem and click OK to proceed 2 Connect Setup x Connection Setu COM Pot comi y Flow Control None Baud Rate fi 15200 Data Bits lB WH Stop Bits htt H Parity None OF Cancel A ATTENTION If you are not sure which communication parameters you should use please select the Auto Detect Serial Settings option and follow the onscreen instructions The procedure may take few minutes to complete When using the Auto Detect Serial Settings function if the GSM or t
69. rate how to load a profile using Configurator 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON Start OnCell Configurator and select the Create a new Configuration File from Configurator option 2 OnCell Configurator x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modem Load 4 Configuration File Load an existing Configuration File to Configurator 3 Inthe File menu select Load File from 2 OnCell Configurator 2101 File Terminal Emulator Help Go to Mode Wizard gl SMS Tunnel lr Strings pawe File Device Mam E Apply Load File From Exi Baud Rate ld ual Get Settings eende x 3 26 OnCell G2100 Series User s Manual OnCell Configurator 4 Select a folder and profile and click Open Look in E Desktop de Ez Fe o E My Documents 4 My Computer My Recent My Network Places Documents APP Gad PIC Dezkto p My Documents E Sr My Computer Product Software My Network File name 621 BOL Save_O1 txt T Places Files of type Tat files Ext ti 5 The modem configuration stored in the profile will be displayed in Configurator OnCell Configurator i lolx Fie Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings Senal Interfa
70. s Back Fancel I 11 At this point the OnCell G2100 Series driver should be listed in Phone and Modem Options on the Modems tab Phone and Modem Options j E 2 x Dialing Rules Modems Advanced Be The following modems are installed Modem ttsched To ES Moza OnCell G2100 Series GSM GPRS Modem COM 1 7 OnCell G2100 Series User s Manual GPRS Connection Modem Diagnostics The following instructions explain how to verify that the modem is installed properly and has been activated 1 From the Control Panel open Phone and Modem Options On the Modem tab click Properties Phone and Modem Options E 1215 Dialing Rules Modems Advanced a The following modems are installed Modem i Attached To 24 Moxa OnCell 62100 Series GSM GPRS Modem COM Add Remove d OF Cancel A ATTENTION Make sure that the RS 232 port of the OnCell G2100 Series modem is connected For the OnCell G2150L make sure DIP switch 1 is set to ON Make sure the SMS Tunnel Mode is disabled If the GSM LED is blinking that means that SMS Tunnel Mode is enabled and activated To switch back to Command Mode you must send the escape command using terminal software or remove the SIM card directly 7 8 OnCell G2100 Series User s Manual GPRS Connection 2 On the Diagnostics tab click Query Modem zix General Modem Diagnostics Advanced Driver
71. s and click Create a new connection 2 When the New Connection Wizard window opens select Connect to the Internet and click Next New Connection Wizard h Network Connection Type What do pon want to do Connect to the Internet Connect to the Internet sa you can browse the Web and read email C Connect to the network at my workplace Connect to a business network using dial up or PAN so you can work from home a field office or another location C Set up a home or small office network Connect to an existing home or small office network or set up a new one Set up an advanced connection Connect directly to another computer using your serial parallel or infrared port or set up this computer so that other computers can connect to it lt Back Cancel 3 Select Set up my connection manually and click Next New Connection Wizard E Getting Ready The wizard i preparing to set up pour Internet connection How do vou want to connect to the Internet Choose from a list of Internet service providers ISPs Set up my connection manually For a dial up connection you will need your account name password and a phone number for your SF For a broadband account you won t need a phone number C Use the CD got from an ISP lt Back Cancel 7 12 OnCell G2100 Series User s Manual GPRS Connection 4 Select Connect using a dial up modem and click Next Mew Connection
72. scsssnsscnsecnsscensnesensnensnensnenssensseensnensnsnens A 1 Federal Communication Commission Interference Statement B 1 1 Introduction The OnCell G2100 Series of industrial GSM GPRS modems provide an easy way to connect your remote RS 232 or RS 422 485 serial devices to GSM and GPRS mobile networks The following topics are covered in this chapter Overview Package Checklist Features Specifications DODDO Pin Assignments OnCell G2100 Series User s Manual Introduction Overview The OnCell G2100 Series modem is a quad band GSM GPRS modem that transmits data and short messages SMS over GSM GPRS mobile networks The modem can be used to improve the efficiency of your maintenance and communication and does not require a high level of technical knowledge to operate All models provide standard RS 232 communication and 15 KV ESD serial line protection ideal for attaching devices such as stand alone controllers PC COM ports and multi drop electric meters The enclosure is IP30 rated and can be mounted on a DIN rail or on the wall 12 to 48 VDC power input 1s supported to connect different types of field power sources Status information 1s clearly provided through several LED indicators including signal strength and mode of communication The OnCell G2100 Series includes the following models e OnCell G2110 industrial GSM GPRS modem RS 232 e OnCell G2110 T industrial GSM GPRS modem RS 232 wide operating tem
73. select the COM port that you are using and click Next Add Hardware Wizard Install New Modem Select the ports pon want to install the modem on Tou have selected the following modem Moa OriCell G2100 Seres GSM GPRS Modern On which ports do you want to install it C All ports Selected ports COM lt Back Cancel 9 A message will appear stating that the driver has not passed Windows Logo testing Click Continue Anyway to proceed Hardware Installation AN The software vou are installing for this hardware l Mosa OnCell G2100 Series GSM GPRS Modem haz not passed Windows Logo testing to verifp its compatibility with Windows lt P Tell me why this testing ls important Continuing your installation of this software may impair or destabilize the correct operation of your system either immediately or in the future Microsoft strongly recommends that you stop this installation now and contact the hardware vendor for software that has passed Windows Logo testing cane STOP Installation 7 6 OnCell G2100 Series User s Manual GPRS Connection 10 Click Finish to complete the installation procedure Add Hardware Wizard Install New Modem Modem installation is finished four modem has been set up successfully IF You want to change these settings double click the Phone and Modem Options icon in Control Panel click the Modems tab select this modem and then click Propertie
74. tocol nternet Protocol The default Wide area network protocol that provides communication across diverse interconnected networks Cancel 7 16 OnCell G2100 Series User s Manual GPRS Connection 12 If you know the IP address of the DNS server select Use the following DNS server addresses and enter the IP address es as prompted Click OK Internet Protocol TCP IP Properties x General ou can get F settings assigned automatically if your network supports this capability Otherwise you need to ask your network administrator for the appropriate IP settings f Obtain an IP address automatically C Use the following IP address IP address Obtain ONS server address automatically f Use the following ONS server addresses Prefered ONS server 66 209 10 201 Alternate DNS server 66 209 10 204 Advanced Cancel ATTENTION For detailed DNS information please refer to the APN List on the Document and Software or consult your service provider for further details 7 17 OnCell G2100 Series User s Manual 13 Click OK f Cingular Wireless Properties General Options Security Networking Advanced Type of dial up server am calling Settings Thit connection uses the following tems 37 Internet Protocol TCP IP m os Packet Scheduler LJ 2 File and Printer Sharing for Microsoft Networks L El Client for Microsoft
75. ton Simply hold the RESET button down for 10 seconds and the modem will be reset to the factory default settings This feature is implemented on the following model revisions and later the OnCell G2150I Rev 1 3 OnCell G2110 Rev 1 1 and OnCell G2110 T Rev 1 1 RESET button The RESET button performs different operations depending on how long it is held down as follows 1 to 3 sec Restart the system 3 to 10 sec GSM GPRS SMS Tunnel stop running PWR LED blinks Over 10 sec LEDs turn OFF and ON factory default settings restored 3 38 4 AT Command Set The AT Command Set can be used to operate configure and query the OnCell G2100 Series modem This chapter includes information about the AT Command Set of the OnCell G2100 Series modem The following topics are covered in this chapter AT Command Set Introduction Starting Moxa Terminal Emulator AT Command Examples Radio Band Selection PIN Code Management Serial Line Settings 2 wire RS 485 Communication OnCell G2150I Only Additional Information OUUWUUWUUWUOWOUD OnCell G2100 Series User s Manual AT Command Set AT Command Set Introduction The OnCell G2100 Series modem supports the V 25ter AT command set The AT prefix also known as the Attention Code signals the modem that one or more commands are to follow The AT command set is an industry standard language that is used to communicate with modems The OnCell G2100 Series modem is always either in comm
76. unication Standard Compliance Radio Band Selection Tx Power GPRS Multi slot Class GPRS Terminal Device Class CSD Data Transmission Rate SMS SIM Control Antenna Connector Antenna Serial Port No of Ports Interface Connector GSM Global Service for Mobile and GPRS General Packet Radio Service Quad band 850 MHz 900 MHz 1800 MHz and 1900 MHz 1 Watt GSM1800 1900 2 Wattt EGSM 900 GSM 850 Class 10 CS1 to CS4 coding schemes Class B simultaneous GPRS CSD connections not supported Up to 14 400 bps Point to point Text PDU Mobile Originated MO and Mobile Terminated MT Cell Broadcast in accordance with GSM 07 05 3V 1 8V interface SMA 0 dB1 10 cm magnetic mount SMA 3 meters GSM 850 EGSM 900 Frequency RX 869 to 894 MHz 925 to 960 MHz Frequency TX 824 to 849 MHz 880 to 915 MHz 9 0 RF Power Stand 2W at 12 5 duty RW at 12 5 duty cycle cycle Impedance 50Q VSWR Typical Radiated Gain 0 dBi on azimuth plane GSM 1800 GSM 1900 Frequency RX 1805 to 1880 MHz 1930 to 1990 MHz Frequency TX 1710 to 1785 MHz 1850 to 1910 MHz o 0 RF Power Stand IW at 12 5 duty 1Wat 12 5 duty cycle cycle Impedance 50 VSWR Typical Radiated Gain 0 dBi on azimuth plane l OnCell G2110 RS 232 OnCell G2110 T RS 232 OnCell G21501 RS 232 and RS 422 485 separate interfaces OnCell G2110 DB9 female OnCell G2110 T DB9 female OnCell G21501 DB9 female for RS 232 5 pin terminal block for RS
77. y desktop To create the connection and close this wizard click Finish lt Back Cancel 9 In the next window that opens click Properties Connect Cingular Wireless fm ajx User name Jispda cingulargprs com Password Fo change fie saved password click hera e Save this user name and password for the following users f Me only Anyone who uses this computer Dial 991 Dial Cancel 7 15 OnCell G2100 Series User s Manual 10 Verify that Use dialing rules on the General tab is NOT selected t Cingular Wireless Properties i xj General Options Security Networking Advanced Connect uzing E Modem Wosa OnCell 62100 GSM GPAS Modem COM Phone number Area code Phone number sis ia Ht Alternates Countrtregion code Use dialing rules Dialing Rulez I Show icon in notification area when connected GPRS Connection 11 On the Networking tab select Internet Protocol TCP IP and click Properties to set the DNS IP address i Cingular Wireless Properties MM x General Options Security Networking Advanced Type of dial up server am calling S ethirugs This connection uses the Following items 7 Internet Protocol TCP IP 05 Packet Scheduler O amp File and Printer Sharing for Microsoft Networks oO El Client for Microsoft Networks Install Uninstall Description Transmission Control Pro
78. ype AT amp W and press Enter to save the settings Note that because the local echo is disabled users will no see any response from the modem at the terminal screen 10 x Profile Edit Port Manager Window Help al alla alele X28 AT amp W is entered here OK is the response from the modem 5 On the bottom of the modem set DIP switch 1 to OFF DIP switch 2 to ON and DIP switch 3 to ON This configures the modem for 2 wire RS 485 communication Additional Information eo V 25ter recommendation Commands that are not listed in the OnCell G2100 Series AT Commands Guide on the Document and Software CD are not supported For commands that are not supported the OnCell G2100 Series modem will respond with ERROR Modulation control error control and data compression commands are not recognized An ERROR string will be returned e GSM 07 05 recommendation 07 05 commands that are not described in this manual will not be implemented An ERROR string will be returned e GSM 07 07 recommendation 07 07 commands that are not described in this manual will not be implemented An ERROR string will be returned The ATQ1 command for Result Code Suppression not transmitted is not supported e Moxa s proprietary AT commands are supported by firmware versions V1 2 and later Please refer to the OnCell G2100 Series AT Commands Guide on the Document and Software CD for further information gt GSM C
79. zard suum 3 Load a Configuration File Load an existing Configuration File to Configurator Nent Cancel 3 14 OnCell G2100 Series User s Manual OnCell Configurator 3 On the PIN and Band Management page enter the correct PIN in the text input box 2 OnCell Configurator PIN and Band Management SIM Card PIN Setup IF your SIM card requires a PIN enter it here bo00 00M Hz 1800MHz 1500MHz 05071 300MmH 2 300 1 800MHz 300 1 SO0KMH 2 Back Hent Cancel Configuring the Radio Band The following instructions 1llustrate how to configure the radio band using Configurator 1 Connect the RS 232 port of the OnCell G2100 Series modem to a host PC On the OnCell G2150I make sure the RS 232 port is connected and DIP switch 1 is set to ON 2 Start OnCell Configurator and select the Create a new Configuration File from Configurator 2 OnCell Configurator x Welcome to the OnCell Wizard Use this wizard to set up pour OnCel G2700 cellular modem a Lontiguration File f Create a new Configuration File from Configurator Load 4 Configuration File Load an existing Configuration File to Configurator E Cancel 3 15 OnCell G2100 Series User s Manual OnCell Configurator 3 On the GSM Setting tab select the correct radio band for your application 2 OnCell Configurator Ioj x Fie Terminal Emulator Help Basic Setting GSM Setting SMS Tunnel Init Strings

Moxa OnCell G2110-T

Contents

Download Pdf Manuals

Related Search

Related Contents