Infocus IN1112 data projector
Contents
1. activate your laptop s external video port On most laptops hold down the FN key while pressing a key labeled CRT LCD LCD VGA a monitor icon Q or similar Key combos for popular models Apple F7 HP Compaq Fn F4 or Fn F6 Sony Fn F7 Dell Fn F8 IBM ThinkPad Fn F7 Toshiba Fn F5 Fujitsu Fn F10 Complete laptop activation chart at www infocus com support IMPORTANT If there is still no video restart your computer first make sure it s connected to the projector and the projector is turned on 6 Change source if needed If needed press source on the projector or remote to view the source You may have to press it more than once Adjust the picture Height s Projector Location As distance increases the image gets larger and moves upwards 1 Hold down the release button under 222 the front of the projector Lens center line 2 Lift the front of the projector to the desired height Diagonal Distance to Screen 3 Release the button Screen Size Minimum Maximum IN1110 Keystone 60 1 5m 7 10 2 4m 8 7 2 6m 80 2 0m 10 5 3 2m 11 6 3 5m go 2 3m 11 8 3 6m 12 11 3 9m 150 3 8m 19 6 5 9m 21 6 6 6m IN1112 60 1 5m 6 7 2 0m 7 2 2 2m 80 2 0m 8 9 2 7m 9 7 2 9m 90 2 3m 9 10 3 0m 10 10 3 3m 150 3 8m 16 5 5 0m 18 0 5 5m Press the keystone buttons to make the Buy a Screen and Other Custom picture square Accessories www infocus com store Zoom and focus In2. This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures Reorient or relocate the receiving antenna Increase the separation between the equipment and receiver Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Changes or modifications not expressly approved by InFocus Corporation may void authority to operate the equipment EN 5
3. 5022 Warning This is a Class B product In a domestic environment it may cause radio interference in which case the user may be required to take adequate measures The typical use is in a conference room meeting room or auditorium Canada This Class B digital apparatus complies with Canadian ICES 003 Cet appareil num rique de la classe B est conforme a la norme NMB 003 du Canada Agency Approvals UL cUL Other specific Country Approvals may apply Please see product certification label Input ratings 100 240Vac 2 3 0 9A 50 60Hz InFocus reserves the right to alter product offerings and specifications at any time without notice
4. IN1100 Quick Start Guide Guide de D marrage Rapide Schnellstart Anleitung Guia de Inicio Rapido Guida di Consultazione Rapida Snelstartgids Guia de Inicio Rapido Snabbstarthandbok KpaTkoe pyKOBOACTBO WE AEF OFLH A RRA Panduan Ringkas Regulatory models IN1110 and IN1112 P N 36 8KN01G001 A DISPERINDAG No 0287 1 824 51 09 03 InFocus Bright Ideas Made Brilliant A Unpack the box Here s what s included Please read the safety instructions booklet before setting up the projector Projector with Lens Cap Remote Carrying case USB Cable Computer Cable Power Cable Save the box and packing materials Put batteries in the remote The remote uses 2 AA batteries Please dispose of batteries in an environmentally proper manner Buy a Full Featured Remote and Other Custom Accessories www infocus com store Status Indicator Panel Power Standby Service Required The top of your projector includes a convenient indicator panel with symbols that light up to show important status f For details see Troubleshooting High Temperature Replace Lamp Connect source Color coded connections make it easy You can connect more than one source if needed Connect to Computer using VGA Got an Apple computer You may need an adapter For more information see How To Guides at www infocus com support howto Co
5. Mon Fri 6 am 5 pm Pacific Australia Direct Sales 61430 223 138 Italy 0800 877 238 China 800 888 9288 Spain 900 993 163 Singapore 65 6603 9871 UK 0800 028 6470 New Zealand 008000 4636287 Other 008000 463 6287 Mon Fri 9 a m 5 p m SGT Mon Fri 08 00 17 00 CET ap support infocus com emea support infocus com Hg Lamp contains mercury Manage in accordance with local disposal laws See www lamprecycle org Declaration of Conformity Manufacturer InFocus Corporation 13190 SW 68th Parkway Portland Oregon 97223 8368 USA We declare under our sole responsibility that this projector conforms to the following directives and norms EMC Directive 2004 108 EC EMC EN 55022 EN 55024 EN 61000 3 2 EN 61000 3 3 Low Voltage Directive 2006 95 EC Safety IEC 60950 1 2005 Trademarks Apple Macintosh and PowerBook are trademarks or registered trademarks of Apple Computer Inc IBM is a trademark or registered trademark of International Business Machines Inc Microsoft PowerPoint and Windows are trademarks or registered trademarks of Microsoft Corporation Adobe and Acrobat are trademarks or registered trademarks of Adobe Systems Incorporated DLP and the DLP logo are registered trademarks of Texas Instruments and BrilliantColor is a trademark of Texas Instruments InFocus In Focus and INFOCUS stylized are either registered trademarks or trademarks of InFocus Corporation in the United States and other countries FCC Warning
6. mputer Cable included Computer Connect to DVD VCR 1 Connect video using a S Video or a Composite Video Cable www infocus com store part no SP SVIDEO 10M or SP CPSTVID 5M 2 Connect video using a HDMI Cable www infocus com store part no SP HDMI 10M R 3 Connect audio using a Mini Plug to RCA Audio Y Cable Available from A V dealer or retailer HDMI Cable Best S Video Cable kk Better Composite Video Cable Mini Plug Audio Y Cable HDMI Out Video Out zJ DVD VCR or HDTV Receiver cd g e UJ Connect to Other kinds of sources How To Guides are available at www infocus com support howto Audio Out Also for game console or cable box Turn on projector and source 1 Connect the power cord to the projector and to an electrical outlet The power light 5 on the projector will light amber 2 Remove the lens cap 3 Turn on the projector Touch the power light or press power on the remote The power light will start blinking green 4 Wait for the lamp to warm up After a few seconds the power light will stop blinking and the other buttons on the keypad will light up It can take a minute for the lamp to reach full brightness WARNING Do not look directly into the lens when the projector is turned on 4 Turn on computer or other source You may need to press a specific key combination to
7. port Serial number 2 Go to www infocus com register Download it at www infocus com support The Reference Guide is available in multiple languages It covers advanced setup and operation including lamp replacement instructions If there is no picture or the picture is blank 1 If the power light is off make sure the power cord is connected and plugged into a live electrical outlet If the power light is amber and not blinking touch the power light or press power on the remote Check video source and cables Make sure the video source computer DVD player VCR etc is turned on and cables are securely connected between the source and the projector 5 Press the Source button You may need to press it several times to view the correct source Q Press the Auto Image button If Signal out of range is shown or the picture looks bad S Press the Auto Image button If that doesn t help and the source is a computer reduce your computer s display resolution or vertical refresh rate If the replace lamp light is on Turn the projector off and wait at least one minute then turn it on again If the Replace Lamp light turns on again the lamp needs to be replaced For lamp replacement instructions see the Reference Guide which can be downloaded at www infocus com support Only InFocus genuine lamps are tested for use in this projector If the high temperature light is on Turn the projector off and remo
8. teractive Screen Size and Distance Calculator www infocus com calculator Ceiling mount To flip the image turn on the Ceiling Mount setting in the Advanced gt Setup gt Image setup menu Zoom rear Focus front Adjust zoom first then focus the center of the image 4 Note Most picture settings are disabled gray unless a source is being displayed Using the menus menu Press MENU then press w or A to review the menu options To enter a submenu highlight the desired submenu and press 8 SELECT C To adjust a menu setting highlight the desired menu option and press SELECT or gt Then press lt or gt to scroll through the available adjustments To save your adjustments press SELECT Press the MENU button to exit the menu system select 7 Turn off the projector Press the power button The power light on the projector will blink while the fan cools the lamp If you need to unplug the projector wait until the fan stops and the power light stops blinking and stays on Note While the power light is blinking button presses on the projector and remote are ignored Register your product Activate your warranty to ensure eligibility for service and support Get special offers and notifications about free product updates 1 Write down your projector s serial number It s printed on the label on the back of the projector You ll need it to register and if you ever need to contact sup
9. ve anything that may be blocking the air vents on its side Leave the projector off for at least one minute to let it cool before turning it on again IMPORTANT Continuous operation at high temperature may reduce the lifetime of the lamp and or projector If the service required light is on Turn the projector off and wait at least one minute then turn it on again If the Service Required light turns on again the projector needs to be serviced See below for service contact information More troubleshooting options are in the Reference Guide Download it at www infocus com support WARNING In the unlikely event of a lamp rupture particles may be ejected from the projector Keep out of the area under and around the projector while the projector is in use See the safety instructions booklet for more details Questions We re here to help Visit us at www infocus com support We re here to support you with your new purchase We can help you with e Determining screen sizes e Documentation in other languages e Connecting your sources TV DVD Cable Satellite Game etc e Selecting optional accessories e Product warranty protection plans USA Canada Latin America Asia Pacific Europe Middle East Africa Customer Support Telephone Customer Support Telephone Customer Support Telephone 1 503 207 4700 Australia 1300 290 922 France 0800 905 993 TOLL FREE 877 388 8360 Mon Fri 9 a m 5 p m EDT Germany 0800 181 3649
Download Pdf Manuals
Related Search