LSI LSIiBBU08
Contents
1. 14 MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Bracket Screw A AN A Press Here N AW WAAAANNRRCAARRRCKAAG WW W NACE AW N WWW W VANS ATTERT 85039 09 Edge of _ pW Edge of Motherboard Motherboard Figure 8 Reinstalling the MegaRAID SAS Controller 4 Secure the controller to the computer chassis with the bracket screw 5 Replace the computer cover and reattach the power cords 6 Turn on the power to the computer See the MegaRAID SAS Software User s Guide for information about running the RAID configuration utility and installing the software drivers For assistance in installing configuring or running the LSIiBBU08 contact an LSI Technical Support representative NOTE Record your controller serial number in a safe location in case you need to contact LSI about your RAID controller Click the following link to access the LSI Technical Support page for storage and board support http www si com support storage tech_support index html From this page you can send an email or call Technical Support or submit a new support request and view its status Support Request http www si com support support_form html LSI Corporation Confidential August 2010 MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Technical Support Phone Support http www si com support s2. Installation Guide MegaRAID LSIiBBU08 Intelligent Battery Backup Unit The LSI MegaRAID LSIiBBUO8 is an intelligent battery backup unit iBBU that protects the integrity of the cached data on a MegaRAID RAID controller for up to 48 hours depending on the derated retention time selected in case of a complete AC power failure or a brief power outage LSI Corporation Confidential August 2010 Thank you for purchasing the LSI MegaRAID LSIiBBUO8 Before you install your RAID controller please take a few minutes to read this quick installation guide If you need more information about any topic covered in this guide refer to the related documents on your MegaRAID Universal Software Suite CD This quick installation guide explains how to install the LSIiBBUO8 directly or remotely with your RAID controller The LSIiBBU08 which is based on Lithium ion LION battery cell technology can be used in two application modes Mode 1 The LSIiBBU08 uses a small board to board connector to mount directly to the following SAS RAID controllers MegaRAID SAS 9260 4i MegaRAID SAS 9260 8 MegaRAID SAS 9261 8i MegaRAID SAS 9280 4i4e MegaRAID SAS 9280 8e Mode 2 The LSIiBBU08 connects remotely to the following SAS RAID controllers using a 12 inch cable or where applicable a 12 inch cable and a remote interposer board that are sold separately in a Remote Battery Kit MegaRAID SAS 9260 4i MegaRAID SAS 9260 8i MegaRAID SAS 926
3. LSIiBBU08 only if the rails on the cable connectors align with the slots on the other connectors Do not force the cable into the 20 pin connectors The cable end inserts into the connector with minimal resistance Page 12 LSI Corporation Confidential August 2010 LSI Corporation Confidential MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Reinstalling the Controller in the Computer Figure 8 Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller ET RY is mm mi eR re T KG oT ee hee A V WW REE AAAA NSCSASARRRCERE N A VA RH N N RNN SANS NN AAi x Figure 7 Connecting the LSIiBBU08 Remotely to the Interposer Card Follow these steps to install the RAID controller in the computer 1 With the power to the chassis still turned off and the power cords unplugged make sure the chassis is grounded and has no AC power Insert the RAID controller in a PCI Express slot on the motherboard as shown in NOTE Some PCI Express slots support only PCI Express graphics cards if a RAID controller is installed in one of these slots it will not function Refer to your computer documentation for information about the PCI Express slot 3 Press down gently but firmly to seat the card correctly in the slot August 2010 Page 13 Technical Support Technical Support Page
4. lines up with the JT3 board to board connector on the controller Carefully press the J1 connector on the interposer card into the JT3 connector on the controller so that the two connectors are firmly joined The connectors fit only when they are in the correct alignment Use the other screw to secure the interposer card to the controller and continue with the next procedure Page 11 Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Figure 6 Connecting the Interposer Card to the MegaRAID SAS 9260 8i RAID Controller Connecting the Cable Between the Follow these steps to connect the cable between the interposer card on the controller Interposer Card and the LSIiBBU08 and the LSIiBBUOS 1 Mount the LSIiBBU08 to the chassis of your computer based on the location and the type of mounting option 2 With the controller on a flat clean static free surface ground yourself and make sure the system is grounded 3 Remove the cable included in the Remote Battery Kit sold separately Insert one end of the cable into the 20 pin J2 connector on the LSIiBBU08 and the other end into the 20 pin J1 connector on the interposer card as shown in Figure 7 Align the black triangles on the connectors to make sure they are connected properly NOTE The cable connectors are polarized and can be inserted into the connectors on the interposer card and the
5. the battery daughtercard cable and standoff This combination enables authorized resellers and chassis manufacturers to customize the location of the remote battery to provide the most flexibility within various environments Follow these steps to remove the RAID controller from the computer 1 Turn off the power and unplug the power cords Ground yourself and make sure the system is grounded Remove the cover from the computer according to the instructions in the system user s manual to allow access to the controller Unplug all cables from the controller remove the screw attaching the bracket to the computer chassis and carefully remove the controller from the slot Place the controller on a flat clean static free surface and continue with the next procedure Follow these steps to install the interposer card on the controller as shown in Figure 6 With the controller on a flat clean static free surface ground yourself and make sure the system is grounded Remove the interposer card standoff and screws from the package Place the standoff on the controller so that the bottom side is over the screwhole next to the JT3 BBU connector on the controller Use one of the screws to secure the standoff to the controller CAUTION Center the screwdriver carefully to avoid stripping the screwhead Do not overtighten the screws 5 Hold the interposer card so that the J1 board to board connector on the interposer card
6. 0 16i MegaRAID SAS 9261 8i MegaRAID SAS 9280 4i4e MegaRAID SAS 9280 8e MegaRAID SAS 9280 16i4e MegaRAID SAS 9280 24i4e LSI provides a family of MegaRAID iBBUs for use with its high performance MegaRAID RAID controllers The LSI MegaRAID iBBUs provide an inexpensive alternative to using an uninterruptible power supply UPS and a second level of fault tolerance when used with a UPS Page 3 Front View and Rear View of the LSIiBBU08 MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide To mount the LSIiBBU08 on the RAID controller directly follow the steps in Installing the LSIiBBU08 Directly on the MegaRAID SAS RAID Controller To connect the LSIiBBU08 to the RAID controller remotely follow the steps in Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller Front View and Rear View of the The following figure shows the front view and the rear view of the LSIiBBU08 The front LSIiBBU08 view is the side that you can see after you install the LSIiBBU08 on the RAID controller lt lt Note that the LSIiBBUO8 combines a battery pack with a daughtercard The LSIiBBU08 uses screws and standoffs to connect to the controller sie WARNING The battery used in LSI A this device may present a risk of fire or Model BAT 1S1P chemical burn if mistreated DO NOT dissemble heat above 60C crush or BBU PIN L4 25343 04 fi sh rt Gircuit ext gt i tacis MNANE crcispose in fre orwater gt neS BBU
7. S N SY02700225SO oS OUI KIA c Al Contains MH29557 Sony US454261A8T Cell Rechargeable Li Polymer Battery Pack Rating 3 7V 1 59Ah 5 9Wh Finished in China 85065 00 1 J2 remote connector 2 J1 board to board connector Figure 1 Front View and Rear View of the LSIiBBU08 NOTE Record your controller serial number in a safe location in case you need to contact LSI Page 4 LSI Corporation Confidential August 2010 MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Installing the LSIiBBU08 Directly on the MegaRAID SAS RAID Controller Installing the LSIiBBU08 Directly on the MegaRAID SAS RAID Controller Removing the RAID Controller from the Computer Installing the LSIiBBU08 on the RAID Controller LSI Corporation Confidential August 2010 This section describes how to install the LSIiBBU08 directly on the MegaRAID SAS 9280 8e RAID controller You can connect the LSIiBBU08 in the same way to the other MegaRAID SAS RAID controllers that use this iBBU For information about the BBU connectors on these controllers see the MegaRAID 6Gb s SAS RAID Controllers User s Guide Perform the following tasks described in this section in order to connect the LSIiBBU08 directly to the RAID controller 1 Removing the RAID Controller from the Computer 2 Installing the LSIiBBUO8 on the RAID Controller 3 Reinstalling the RAID Con
8. angles on the connectors help you install them properly Insert the cable connectors so that the black triangles are aligned LSI Corporation Confidential August 2010 MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller Figure 4 Connecting the LSIiBBU08 Remotely to the SAS 9280 8e RAID Controller Reinstalling the RAID Controller on Follow these steps to reinstall the RAID controller on a motherboard the Motherboard 1 With the power to the chassis still turned off and the power cords unplugged make sure the chassis is grounded and has no AC power 2 Insert the RAID controller in a PCI Express slot on the motherboard as shown in Figure 5 NOTE Some PCI Express slots support only PCI Express graphics cards if a RAID controller is installed in one of these slots it will not function Refer to your computer documentation for information about the PCI Express slot 3 Press down gently but firmly to seat the card correctly in the slot LSI Corporation Confidential August 2010 Page 9 Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide S 0 85065 04 Edge of Motherboard Edge of Motherboard Figure 5 Installing the MegaRAID SAS Controller 4 Secure the controller to the computer chassis with th
9. e bracket screw 5 Replace the computer cover and reattach the power cords 6 Turn on the power to the computer Connecting the Remote LSIiBBU08 to an This section describes how to install the LSIiBBUO8 remotely on the MegaRAID SAS Interposer Card on the MegaRAID SAS 9260 8i RAID controller You can connect the LSIiBBU08 in the same way to the other RAID Controller MegaRAID SAS RAID controllers that use this iBBU NOTE Only the MegaRAID SAS 9260 4i and SAS 9260 8 RAID controllers use the interposer card with the LSIiBBUO8 To connect a remote RAID controller to an interposer card on your RAID controller perform the following tasks in order 1 Removing the RAID Controller from the Computer 2 Installing the Interposer Card on the Controller 3 Connecting the Cable Between the Interposer Card and the LSIiBBU08 4 Reinstalling the Controller in the Computer Page 10 LSI Corporation Confidential August 2010 MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller Removing the RAID Controller from the Computer Installing the Interposer Card on the Controller LSI Corporation Confidential August 2010 NOTE Because server and workstation chassis vary from vendor to vendor no standard mounting option exists that is compatible with the various system configurations The LSIiBBU08 battery kit in combination with the Remote Battery Kit includes
10. ged make sure the chassis is grounded and has no AC power 2 Install the RAID controller in a PCI Express slot on the motherboard as shown in Figure 3 NOTE Some PCI Express slots support only PCI Express graphics cards if a RAID controller is installed in one of these slots it will not function Refer to your computer documentation for information about the PCI Express slot 3 Press down gently but firmly to seat the card correctly in the slot LSI Corporation Confidential August 2010 MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller 85065 02 Edge of Ww Motherboard Edge of Motherboard Figure 3 Reinstalling the MegaRAID SAS 9280 8e RAID Controller 4 Secure the controller to the computer chassis with the bracket screw 5 Replace the computer cover and reattach the power cords 6 Turn on the power to the computer Connecting the LSIiBBU08 This section describes the two methods you can use to connect the LSIiBBU08 remotely Remotely to the MegaRAID SAS to your MegaRAID SAS RAID controller using a cable or where applicable a cable and a RAID Controller remote interposer board that are sold separately in a Remote Battery Kit m Use the cable to connect the remote LSIiBBU08 to the BBU connector on the RAID controller Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller m Use the cable to co
11. la LSISSK MegaRAID LSIiBBU08 Intelligent Battery Backup Unit Quick Installation Guide 46307 00 Revision A August 2010 Revision History Version and Date Description of Changes 46307 00 August 2010 Initial release of document LSI and the LSI logo are trademarks or registered trademarks of LSI Corporation or its subsidiaries All other brand and product names may be trademarks of their respective companies LSI Corporation reserves the right to make changes to the product s or information disclosed herein at any time without notice LSI Corporation does not assume any responsibility or liability arising out of the application or use of any product or service described herein except as expressly agreed to in writing by LS Corporation nor does the purchase lease or use of a product or service from LSI Corporation convey a license under any patent rights copyrights trademark rights or any other of the intellectual property rights of LSI Corporation or of third parties This document contains proprietary information of LSI Corporation The information contained herein is not to be used by or disclosed to third parties without the express written permission of LSI Corporation Corporate Headquarters Website Milpitas CA www lsi com 800 372 2447 Document Number 46307 00 Rev A Copyright 2010 LSI Corporation All Rights Reserved MegaRAID LSIiBBU08 Intelligent Battery Backup Unit Quick Installation Guide Quick
12. nnect the remote LSIiBBU08 to a daughtercard that is connected to the BBU connector on the RAID controller Connecting the Remote LSIiBBU08 to an Interposer Card on the MegaRAID SAS RAID Controller The procedures in this section show how to connect the LSIiBBU08 remotely to the MegaRAID SAS 9280 8 RAID controller You can connect the LSIiBBU08 in the same way to the other MegaRAID SAS RAID controllers that use this iBBU For information about the BBU connectors on these controllers see the MegaRAID 6Gb s SAS RAID Controllers User s Guide Connecting the Remote LSIiBBUOS8 to the This section describes how to connect the remote LSIiBBU08 to the BBU connector on BBU Connector on the RAID Controller the SAS 9280 8e RAID controller To connect the remote RAID controller to the BBU connector on the RAID controller perform the following tasks in order LSI Corporation Confidential August 2010 Page 7 Connecting the LSIiBBU08 Remotely to the MegaRAID SAS RAID Controller Page 8 Removing the RAID Controller from the Computer Connecting the Remote LSIiBBU08 MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide 1 Removing the RAID Controller from the Computer 2 Connecting the Remote LSIiBBU08 3 Reinstalling the RAID Controller on the Motherboard NOTE Because server and workstation chassis vary from vendor to vendor no standard mounting option exists that is compatible with the various system configuration
13. on a flat clean static free surface With the front side up place the RAID controller on a flat clean static free surface Hold the LSIiBBU08 daughtercard so that the battery side is up and the J1 connector lines up with the J6B1 BBU connector on the SAS 9280 8e RAID controller as shown in the following figure Oe ow Ms NOTE See the MegaRAID 6Gb s SAS RAID Controllers User s Guide for the BBU connectors to use on the other RAID controllers that use the LSIiBBU08 Page5 Installing the LSIiBBU08 Directly on the MegaRAID SAS RAID Controller MegaRAID LSIiBBUO8 Intelligent Battery Backup Unit Quick Installation Guide Reinstalling the RAID Controller on the Motherboard Page 6 85065 01 Figure 2 Installing the LSIiBBU08 Daughtercard on the SAS 9280 8e RAID Controller 6 Carefully press the LSIiBBU08 onto the RAID controller so that the two connectors are firmly joined 7 Secure the LSIiBBU08 to the RAID controller with the screws and the standoffs in the three screwholes The standoffs are threaded at both ends and a screw goes into each end The screw threads from the back of the controller board into the board to board standoffs on the bottom of the LSIiBBU08 CAUTION Center the screwdriver carefully to avoid stripping the screw heads Do not overtighten the screws Follow these steps to reinstall the RAID controller on a motherboard 1 With the power to the chassis still turned off and the power cords unplug
14. s The LSIiBBU08 battery kit in combination with the Remote Battery Kit includes the battery daughtercard cable and standoff This combination enables authorized resellers and chassis manufacturers to customize the location of the remote battery to provide the most flexibility within various environments Follow these steps to remove the RAID controller from the computer 1 Turn off the power and unplug the power cords 2 Ground yourself and make sure the system is grounded Remove the cover from the computer according to the instructions in the system user s manual to allow access to the controller 4 Unplug all cables from the controller remove the screw attaching the bracket to the computer chassis and carefully remove the controller from the slot 5 Place the controller on a flat clean static free surface and continue with the next procedure Follow these steps to connect the remote LSIiBBU08 to the BBU connector on the RAID controller 1 Ground yourself and make sure the system is grounded 2 Remove the LSIiBBU08 from the package 3 Use the three Phillips head screws that are provided to secure the LSIiBBU08 to the motherboard or the server chassis 4 Connect one end of the 12 inch 20 pin cable included in the remote battery kit to the J2 connector on the LSIiBBU08 and the other end to the J6B1 BBU connector on the SAS 9280 8e RAID controller RAID controller as shown in the following figure The black tri
15. torage phone_tech_support index html NOTE The international toll free number does not require country specific access codes LSI Corporation Confidential August 2010 Page 15 Na LSISSK 46307 00A
16. troller on the Motherboard CAUTION Electrostatic discharge can damage the LSIiBBU08 and the MegaRAID SAS RAID controller Make sure that you install the LSIiBBU08 at an ESD safe workstation that meets the requirements of EIA 625 Requirements For Handling Electrostatic Discharge Sensitive Devices When you install the LSIiBBU08 follow the ESD recommended practices in the latest revision of IPC A 610 Follow these steps to remove the RAID controller from the computer 1 Turn off the power and unplug the power cords 2 Ground yourself and make sure the system is grounded 3 Remove the cover from the computer according to the instructions in the system user s manual to allow access to the controller 4 Unplug all cables from the controller remove the screw attaching the bracket to the computer chassis and carefully remove the controller from the slot 5 Place the controller on a flat clean static free surface and continue with the next procedure Follow these steps to install the LSIiBBU08 on the front of the SAS 9280 8e RAID controller WARNING Danger of an explosion exists if the battery is incorrectly replaced Replace the battery only with the same or equivalent type recommended by the manufacturer Dispose of used batteries according to the manufacturer s instructions Ground yourself and make sure the system is grounded Remove the LSIiBBU08 daughtercard from the package Place the LSIiBBU08 front side up
Download Pdf Manuals
Related Search