SpeakerCraft IRC-2.0
Contents
1. length 5300 with 18 gauge Dimensions 2 65mm L x e 14mm W x 4 13mm D SYSTEM CONNECTIONS Striped The following are a few typical applications of the IRC 2 0 and IRC 2 1 for IR repeater systems IRC 4 0 Side IR RECEIVER IR OUT 12V IR OUT 12V nee red A Basic System specter ron STATUS GND Fig 2 shows a basic plug and play installation such as controlling components that are ANS one yellow black behind closed cabinet doors or in a closet O za ES fe O FS ez esi O 7 o E 3 S fe O ES fe Fig 2 OwO CONTROLLED COMPONENTS IN CABINET ETC Rear View A V Receiver A yg ad Restor A rey To Switched A O reduce rightness AC Outlet IRC 2 0 if desired See Text ee Surface Mount igle IR Receiver WO EZ Connect Terminals iaia IRE 3 0 Visible Emitter gt A V Receiver Joe alli alli 4 5 BER Satellite IRC 2 0 gi iiini z Surface Mount z A ee AT 1 0 a Sis IR Receiver 2288 E ERRATA 5 fe IRE 1 0 Emitter PS 1 0 S z TERMINATOR z 8 i STATUS SpeakerCraft IRE 3 0 Visible Emitter f PATA Og 3 Satellite Supply i D 20 Ss emon E angs DVD SpeakerCraft 5 EM ON O BL ON a4 a5 z el segje SS ez IRE 3 0 Visible Emitt2. LB GLOSS WHITE COATED PAPER SIZE 11 000 X 8 500 FOLD TO 5 500 X 8 500 e FOLDING 1 FOLD VER TICAL FINISH WITH LOGO SHOWING e SCALE 1 1 Requires Power Supply Terminator Block and Emitters for IR Repeater operation Mounting Attaches to any flat surface using the included double sided tape The tape may be applied to the back top or bottom surfaces of the IRC 2 0 IRC 2 1 to accommodate the installation A Multi Room System Fig 3 is an example of the IRC 2 1 wired IR Receiver in a multi room system with other SpeakerCraft IR receivers in various rooms plus a local IRC 2 0 These control the various components in the main room or equipment area Power 12V DC 6 mA Supplied from connected Terminator 1 Pull 4 conductor wire from each room home runs to the AT 1 0 Terminator near the a IR Lens rejects visible light interference Crosshatch Shield internal inhibits EMI ESI Interference Fig 3 Carrier Frequency Acceptance Range 28 to 90 kHz Control Range Up to 35 feet depending on remote strength and ambient noise conditions ROOM 1 ROOM 2 ROOM 3 Control Angle 50 off axis Room to Room Wire Recommendations Use 4 conductor min 24 gauge unshielded IRC 4 0 IRC 2 1 IRC 1 1 J Box IR Receiver solid or stranded copper wire up to 1200 Cat 5e ok 22 gauge up to 2000 20 gauge Surface Mount IR Receiver Flush Mount IR Receiver up to 3000 and 18 gauge up to 5300 Maximum recommended cable
3. PRINTER S INSTRUCTIONS INSTR INSTL IRC 2 LINEAR P N 223166B e INK BLACK e MATERIAL 70 LB GLOSS WHITE COATED PAPER e SIZE 11 000 X 8 500 FOLD TO 5 500 X 8 500 e FOLDING 1 FOLD VER TICAL FINISH WITH LOGO SHOWING e SCALE 1 1 controlled components Note Use 24 gauge unshielded solid or stranded copper wire up to 1200 Cat 5e ok 22 gauge up to 2000 20 gauge up to 3000 and 18 gauge up to 5300 Total lengths include all wire runs from each room added together not just the longest single run If using shielded wire these lengths would be reduced by approximately 30 Also to achieve operation with long lengths the lower DIP switch on the AT 1 0 must be set to the NET ON position 2 Connect IR receivers in each room to the 4 conductor home runs as shown using the 4 conductor terminal strip supplied 3 Connect the home run wires to the correct terminals on the AT 1 0 EZ Connect Terminals Note You may use the SpeakerCraft CB Connecting Block not illustrated stock ASM20200 to help connect the many paralleled home run wires to the AI 1 0 EZ Connect Terminals Install and plug the various emitters into the AT 1 0 Set the DIP switches to EM ON or BL ON if using Blasters behind closet doors and NET ON 6 Plug the local IRC 2 0 IR Receiver into the IR RCVR jack Plug in the PS 1 0 12V DC Power Supply 8 A remote control fired at the IR receivers should now control the components mB N Not
4. aser s sole remedy shall be repair or replacement as provided above In no event will SpeakerCraft be liable for any inci dental or consequential damages arising out of the use or inability to use the product even if SpeakerCraft Inc or a SpeakerCraft Inc Authorized Dealer has been advised of the possibility of such damages or for any claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply All implied warranties on the product are limited to the duration of this expressed warranty Some states do not allow limitation on the length of an implied Warranty If the original retail purchaser resides in such a state this limitation does not apply SpeakerCraft 940 Columbia Avenue Riverside CA 92507 800 448 0976 Fax 888 599 9059 www speakercraft com LITO1200 rev2 223166B 223166B IMAGE 1 rd G Saw J Sen S i G S Q N SmartPath IRC 2 0 amp IRC 2 1 Surface Mount Mini Infrared Receivers INSTALLATION INSTRUCTIONS The IRC 2 0 and IRC 2 1 are very small IR Receivers designed to be mounted on flat surfaces in furniture recesses under shelves etc using the double sided tape supplied Among their unique features is an exclusive Ambient Noise Suppression ANS system It acts to push down IRI CFL EMI or ESI noise sources so that stron ger signals from IR remotes have adequate margin for command of the con tro
5. e Refer to the SpeakerCraft AT 1 0 Instructions for Power Supply considerations STATUS Brightness Fig 3 also shows how an external resistor can be added to reduce the brightness of the Status LED on SpeakerCraft IR Receivers to any desired level In this example a PS 1 0 12V DC Power Supply is used as the voltage source to indicate ON OFF status of an A V Receiver Choose a resistor value that achieves the brightness you desire about 2 2k to 12k 1 8 W Connect it in series with the STATUS lead on each IR receiver desired as shown LIMITED 5 YEAR WARRANTY SpeakerCraft Inc warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship for a period of 5 years provided it was purchased from a SpeakerCraft Authorized Dealer Defective products must be shipped together with proof of purchase prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased or to the SpeakerCraft factory at the address listed on this installation instruction manual Freight collect shipments will be refused It is preferable to ship this product in the original shipping container to lessen the chance of transit damage In any case the risk or loss or damage in transit is to be borne by the purchaser If upon examination at the Factory or SpeakerCraft Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this warra
6. er S EM ON 1 BL ON ane 5 PS 1 0 O FSER F gy Power es DVD Q Suppl IRE 3 0 PP y AT 1 0 Visible Emitter 5 Ppa aene Amplified Terminator AT 1 0 Amplified Terminator IRE 4 0 Dual PS 1 0 P Visible Emitter Power i i i j Supply To 120V AC 1 Mount the IRC 2 0 in a recessed cabinet area or under a shelf using the two sided unswitched To Additional WB WW adhesive tape supplied Plug the IR Receiver and Emitters into the SpeakerCraft AT 1 0 Amplified Terminator as shown Set the DIP switches on the AT 1 0 to EM ON and NET ON or OFF Plug in the Power Supply The remote control fired at the IRC 2 0 should now control the components 2 223166B IMAGE 1 CONTROLLED COMPONENTS AREA MAIN ROOM ETC Controlled Unit
7. lled component Note The ANS will take a few seconds to adjust to a given noise source During this time the blue Activity LED will glow brightly and then fade out If the interfer ence disappears momentarily then returns the fade down process will repeat Certain noise sources however such as Plasma Screens may result in low level flick ering even after the fade down This is normal Such signals have been acted upon by the ANS allowing most equipment to be controlled Fig 1 IR Lens Status LED Activity LED IR OUT green blue GND 12V piisi IRC 2 0 Striped Side TP A IR Pickup Diode 4 Conductor 8 Lead 3 5mm Plug 9 16 lt 29 16 3 4 Conductor 412V Terminal Strip IRC 2 1 status Cepe o g IR OUT Included with Striped Side IRC 2 1 Only FEATURES SPECIFICATIONS a The IRC 2 0 and IRC 2 1 are identical except for lead termination See Fig 1 The IRC 2 0 has a unique 3 5mm quad plug to accommodate STATUS as well as IR Power and Gnd connections The IRC 2 1 comes with stripped ends plusa 4 conductor terminal strip allowing interface connections to in wall room to room wiring a Exclusive Ambient Noise Suppressor ANS system a STATUS Indicator Green LED for System On Off indication ACTIVITY Indicator Blue LED indicates IR signal activity in a completed circuit with a Terminator or an Emitter PRINTER S INSTRUCTIONS INSTR INSTL IRC 2 LINEAR P N 223166B INK BLACK MATERIAL 70
8. nty period SpeakerCraft or the SpeakerCraft Authorized Dealer will at its option repair or replace this product at no additional charge except as set forth below If this model is no longer available and can not be repaired effectively SpeakerCraft at its sole option may replace the unit with a cur rent model of equal or greater value In some cases where a new model is substituted a modification to the mounting surface may be required If mounting surface modification is required SpeakerCraft assumes no responsibility or liability for such modification All replaced parts and product become the property of SpeakerCraft Inc Products replaced or repaired under this warranty will be returned to the original retail purchaser within a reasonable time freight prepaid This warranty does not include service or parts to repair damage caused by accident disaster misuse abuse negligence inadequate packing or shipping procedures commercial use voltage inputs in excess of the rated maximum of the unit or service repair or modification of the product which has not been authorized or approved by SpeakerCraft This warranty also excludes normal cosmetic deterioration caused by environmental conditions This warranty will be void if the Serial number on the product has been removed tampered with or defaced This warranty is in lieu of all other expressed warranties If the product is defective in materials or workmanship as warranted above the purch
Download Pdf Manuals
Related Search