SpeakerCraft PT-1.0
Contents
1. 1 Plug in the IR Receiver and Emitters as shown IR RCVR PT 1 0 Note 1 If the IRC 3 0 lead is not long enough you can extend its length by using the SpeakerCraft Model OIX 1 0 STATUS Quad IR 15 Extension Cable optional EMITTERS Note 2 Since the PT 1 0 employs emitter current sharing you may use any of the IRE 1 0 and 2 0 3 0 or 4 0 SpeakerCraft emitters in any combination you wish 12V DC 2 Plug in the Power Supply 3 For A Basic System Using STATUS Peel off Adhesive To do this you would simply plug a PS 1 0 Power Supply T T Protective Cover into the switched AC Outlet on the rear of the A V ie receiver as shown The 12V lead of the PS 1 0 is then 16mm plugged into the STATUS jack on the PT 1 0 In this way T To 7 the green status LED in the IR Receiver will go ON and _ OFF when the A V receiver is turned ON and OFF This p EENE R gives a power indication for instance when the equipment is behind closed cabinet doors A Basic System To snctied A V Receiver A V Receiver M lt GD Bd Remote Control IRC 3 0 PT 1 0 Vabieemiter PS 1 0 Sheif Top Passive Terminator SAT Supply IR Receiver RRR pio A NTER IRE 4 0 Dual Visible Emitter DVD 12V DC PS 1 0 Power Supply To 120 VAC unswitched IRE 4 0 Dual Visible Emitter 12 V Lead OPTIONAL LEAD For a Basic System Using STATUS 224726X1 IMAGE 22. or a SpeakerCraft Inc Authorized Dealer has been advised of the possibility of such damages or for any claim by any other party Some states do not allow the exclusion or limitation of consequential damages so the above limitation and exclusion may not apply All implied warranties on the product are limited to the duration of this expressed warranty Some states do not allow lim itation on the length of an implied Warranty If the original retail purchaser resides in such a state this limitation does not apply SpeakerCraft SpeakerCraft 940 Columbia Avenue Riverside CA 92507 Phone 1 800 448 0976 Fax 951 787 8747 www speakercraft com 224726X1 IMAGE 1 PRINTER S INSTRUCTIONS INSTR INSTL PT 1 0 LINEAR P N 224726X1 INK BLACK MATERIAL 70 LB GLOSS WHITE COATED PAPER SIZE 4 250 X 5 500 FOLD TO 4 250 X 2 750 FOLDING 1 FOLD HORIZONTAL FINISH WITH LOGO SHOWING SCALE 1 1 PT 1 0 Passive Terminator The PT 1 0 provides a quick and low cost means of interconnecting SpeakerCraft Quad Mini Plug equipped IR Receivers with other IR products in basic IR repeating systems It includes a STATUS jack Current sharing resistors at each Emitter jack allows any combination of single or dual emitters to be used Top View a 2 r
3. PRINTER S INSTRUCTIONS INSTR INSTL PT 1 0 LINEAR P N 224726X1 INK BLACK MATERIAL 70 LB GLOSS WHITE COATED PAPER SIZE 4 250 X 5 500 FOLD TO 4 250 X 2 750 FOLDING 1 FOLD HORIZONTAL FINISH WITH LOGO SHOWING SCALE 1 1 col Zoln IX97ZLbZ ana AMT JOJEUIWA SAISSeg O LiLd LIMITED 5 YEAR WARRANTY SpeakerCraft Inc warrants to the original retail purchaser only that this SpeakerCraft product will be free from defects in materials and workmanship for a period of 5 years provided it was purchased from a SpeakerCraft Authorized Dealer Defective products must be shipped together with proof of purchase prepaid insured to the SpeakerCraft Authorized Dealer from whom they were purchased or to the SpeakerCraft factory at the address listed on this installation instruction manual Freight collect shipments will be refused It is preferable to ship this product in the original shipping container to lessen the chance of transit damage In any case the risk or loss or damage in transit is to be borne by the purchaser If upon examination at the Factory or SpeakerCraft Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this warranty period SpeakerCraft or the SpeakerCraft Authorized Dealer will at its option repair or replace this product at no additional charge except as set forth below If this model is no longer available and can not be repaired effe
4. c tively SpeakerCraft at its sole option may replace the unit with a current model of equal or greater value In some cases where a new model is substituted a modification to the mounting surface may be required If mounting surface modification is required SpeakerCraft assumes no responsibility or liability for such modification All replaced parts and product become the property of SpeakerCraft Inc Products replaced or repaired under this warranty will be returned to the original retail purchaser within a reasonable time freight prepaid This warranty does not include service or parts to repair damage caused by accident disaster misuse abuse negligence inadequate packing or shipping procedures commercial use voltage inputs in excess of the rated maximum of the unit or service repair or modification of the product which has not been authorized or approved by SpeakerCraft This warranty also excludes normal cosmetic deterioration caused by environmental conditions This warranty will be void if the Serial number on the product has been removed tampered with or defaced This warranty is in lieu of all other expressed warranties If the product is defective in materials or workmanship as warranted above the purchaser s sole remedy shall be repair or replacement as provided above In no event will SpeakerCraft be liable for any incidental or consequential damages arising out of the use or inability to use the product even if SpeakerCraft Inc
Download Pdf Manuals
Related Search