KTI Networks KG-500F
Contents
1. Provides LED indicators for easy diagnostic Provides SFP to support variety of fiber transceivers Complete driver support for most operating systems Supports 802 1Q VLAN tagging Supports drivers for Windows XP 2K 2K3 VistaX32 VistaX64 Linux NetWare systems and plug and play installa tion for Widnows 2K3 Specifications Standards Network Port Host Interface LEDs Network Cables Transfer Rate Driver Support Power Dimension Environment IEEE 802 3z 1000Base SX LX SFP for 1000Mbps mini GBIC fiber transceiver 32 bit 33 66Mhz PCI Rev 2 1 2 2 2 3 SFP status Link status Optical status 50 125 multimode fiber up to 500m 62 5 125 multimode fiber up to 220m 9 125 single mode fiber Gigabit Ethernet 2000Mbps Full duplex Windows XP 2000 2003 VistaX32 64 Linux Netware server Consumption PCI 3 3V 400mA max 130 x 65 mm Operation Temperature 0 C 50 C Storage Temperature 20 C 85 C Relative Humidity 5 95 non condensing Laser Eye Safe Approval IEC 60825 1 Class 1 CDRH Class I FCC Class B CE CISPR22 Class B Model Definitions Model PCI Connector Fiber Cable Support 500 SX Standard LC 62 5 125 MMF up to 200m 50 125 MMF up to 500m 500 LX Standard LC MMF up to 550m SMF up to 10km 500 LP SX Low profile LC 62 5 125 MMF up to 200m 50 125 MMF up to 500m 500 LP LX Low profile LC MMF up to 550m SMF up to 10km Standard PCI mounted with PCI standard bracket Low profile mounted wi2. The changes or modifications not expressly approved by the party responsible for compliance could void the user authority to operate the equipment CISPR 22 Class B This device complies with EMC directive of the European Commu nity and meets or exceeds the following technical standard EN 55022 Limits and Methods of Measurement of Radio Interference Char acteristics of Information Technology Equipment This device com plies with CISPR 22 Class B CE NOTICE Marking by the symbol C indicates compliance of this equip ment to the EMC directive of the European Community Such marking is indicative that this equipment meets or exceeds the following technical standards EN55022 CISPR 22 ClassB EN55024 EN61000 3 2 EN61000 3 3 EN61000 4 series Introduction The 1000BASE X Gigabit Ethernet PCI Adapter is a 32 bit LAN adapter for use in personal computers with PCI computer bus slots This adapter features a mini GBIC fiber connector SFP for a 1000 Mbps IEEE 802 3z Ethernet network connection over optical fiber cable The series provides different fiber transceiver types support ing short middle and long reach applications Adapter Features Supports 32 bit 33 66MHz PCI of Rev 2 1 2 2 2 3 specifica tion JEEE 802 3z 1000Base SX LX compliant Provides Tx 8K Rx 64KB RAM buffer Supports full duplex operation up to 2000Mbps data rate over fiber Supports full duplex flow control Plug and Play installation
3. Installation Guide 1000Base X Gigabit Ethernet PCI Adapter with SFP Support KG 500F series DOC 070607 KG 500F K The information contained in this document is subject to change without prior notice Copyright C All Rights Reserved TRADEMARKS All brand names are trademarks or registered trademarks of their respective holders FC Warning This equipment has been tested and found to comply with the limits for Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction manual may cause harmful interference to radio commu nications However there is no guarantee that interference will not occur in a particular installation If this equipment does cause harm ful interference to radio or television reception which can be deter mined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver e Connect the equipment into an outlet on a circuit different from that to which the receiver is connected Consult the dealer or an experienced radio TV technician for help Notice
4. any problems first make sure that the appropri ate driver is loaded the proper cable is connected to the connector and the connected device complies with 1000BASE X standard Then recheck the LED 12
5. e and the directory struc tures for the supported operating environments Please refer to this file first before installing any network driver for the adapter Installation for Windows Systems For adapter installation on Windows 2003 Win2K3 the system will detect and configure the drivers for the adapter automatically with no need for extra driver setup The adapter is detected as Win2k3 Realtek RTL8169 8110 Family Gigabit Ethernet NIC Using the Associated Drivers in the driver diskette After driver setup the adapter is identified as Realtek RTL8169 8110 Family Gigabit Ethernet NIC Link Speed Duplex Mode options Auto negotiation Installation for other Systems Refer to README TXT first in the driver CD for the driver instal lation on other operating systems The file contains driver informa tion for most of the popular operating systems 11 LED Indicators The adapter has three LEDs The interpretations of the LEDs are LINK LED indicates an active 1000Mbps connection is established On Good link between the adapter and a remote device Off No connection between adapter and a remote device Blink Link on and traffic activities SFP LED indicates installation status of mini GBIC transceiver On Amini GBIC SFP transceiver is installed in the SFP slot Off No transceiver is installed OL LED indicates optical signal status On Optical signal is detected Off No optical signal is detected If you experience
6. lot the steps are 1 Insert the fiber transceiver into the mini GBIC SFP port Normally a bail is provided for every SFP transceiver Hold the bail and make insertion 2 Until the fiber transceiver is seated securely in the slot place the bail in lock position The mini GBIC SFP slot supports hot plug installation even when the computer is powered and operating Connecting to the Network The rear bracket of the PCI adapter contains two fiber connectors LO Tx LO RA The TX connector is used for transmission and the RX is used for reception When connecting to a device using fiber cable make sure the TX connector of the adapter is connected to the RX connector of the device and RX connector is connected to the TX connector of the device In order to have a reliable communication between two ends the speed and duplex configuration of the adapter s fiber port and the device at the remote end must be same Configure the driver of the adapter as follows Auto 1000Mbps Full duplex 10 Network Driver Installation After making the connection to the network you must install the adapter network driver in order to connect the network adapter to your network operating system The adapter driver media contain the latest versions of the network drivers available when the adapter is shipped from the factory A file README TXT located in the diskette s root directory con tains a list of the supported driver softwar
7. th PCI low profile bracket 5 Board Components The figures show the major components on the adapters with PCI standard bracket and PCI low profile bracket IRLI ELE Adapter with PCI standard bracket Adapter with PCI low profile bracket This LED lights when the fiber connection is established This LED lights when a mini GBIC transceiver module is installed in This LED lights when optical signal is presented in the transceiver No Components Description 1 LINKLED 2 SFPLED the SFP slot 3 OLLED 4 SFP Slot This slot supports mounting a mini GBIC fiber transceiver Installing the Adapter Before installing the adapter you need the following e A computer system that is compliant with the PCI specifica tions version 2 1 or later e An available PCI bus master slot in the computer e The adapter driver diskettes or CD supplied with the adapter Fiber cables Inserting the Adapter into the PCI Slot To install the adapter in your computer follow these steps 1 Turn off the power to the computer 2 Remove the computer s cover 3 Unscrew and remove the slot cover from the PCI bus slot 4 Insert the adapter into the slot and secure the screw 5 Replace the computer cover and reconnect all previously connected cables Installing Mini GBIC Transceiver A typical mini GBIC SFP transceiver is shown as follows YZ en To install a fiber transceiver into the SFP s
Download Pdf Manuals
Related Search