Intellinet 502917 router
Contents
1. Impedance 100 15 Near End Cross talk 38dB 100 MHz Attenuation 22 dB 100 m typical 100 MHz Maximum DC resistance 9 38 100 m 24 AWG at 20 C Maximum DC insulation resistance 150M km 102. filter forwarding rate 148 800 pps 100 Mbps 14 880 pps 10 Mbps e Configuration options Port bandwidth control disable 128 256 512 1024 2048 4096 8192 kbps VLAN port based and tagged up to 8 groups Quality of Service QoS 2 priority levels and port based ratio controlling the ratio between high and low priority Full and half duplex per port MAC address locking e Certifications FCC Class A CE Mark LEDs e Power Link activity for 10 and 100 Mbps e POE Power Input 90 to 260 V AC 50 to 60 Hz Power consumption 180 Watts maximum Package Contents e PoE Web Smart Switch e Power cable e User manual A ANSI TIA ElA 568 A PLUG amp Twisted pair Cable The IEE802 3u Standards permits the use of category 3 4 5 or better balanced cable pairs installed according to ANSI EIA 568 A This appendix provides pinout and brief information for the CAT5 unshielded twisted pair cables B EIA568A pin assignment 1 Plus data transmission Pair 3 2 Minus data transmission Pair 3 Plus data receiver Pair 2 Minus data receiver Pair 2 3 6 Not used by 10BASE T and 5 100Base TX Data pair 1 7 Not used by 10BASE T and 8 100Base TX Data Pair 4 C Recommend CAT5 UTP specifications Physical E FR PVC cable construction E Cable Type 4 pair unshielded twisted pair solid copper E Conductors 24 AWG solid bare annealed copper E Operating temperature 20 C to 75 C Electrical
3. PoE Web Smart Switch Model 502917 User s Manual FCC Warning This device has been tested and found to comply with limits for a Class A digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment This equipment generates uses and radiates radio frequency energy and if not installed and used in accordance with the users manual may cause interference in which case user will be required to correct the interference at his own expense CE Mark Warning This is a Class A product In a domestic environment this product may cause radio interference in which case the user many be required to take adequate measures Table Of Contents A 1 INTOdUGI onice 1 A aliante 2 ChApier ed al dr ao linda enti 3 Package Contents adian Gee oak ieee hah ae See 3 A iii il ne oe ee 4 Front Panel Layout A Function of 8 RJ 45 port 4 B LED Indicators Of 8 Port 10 100Mbps Switch _ 4 Se LED Det S cele 4 POWERED to epee eos 4 NOP TOOM EED aprile si di 4 EKA GT WE Dg eiii 4 Presi 4 Real Panel Layour aida dci anida 5 ARAS PO WEA PU ssa ati 5 ON al eT e o oo A E 6 PACK VIOLENT ix e ati ad sosa Galea escent 6 Si alli 7 Sala o do tae e Seite 7 A How to connect the 502917 to PD device and Existing Switches 7 Chapiero diestra 8 Technical SpeciliGations a ee ie ie
4. d on the port a Rear Panel Layout A AC Power Input AC input 90 260V AC 50 60Hz UL Safety Chapter 4 Rack Mounting Optional Rack mounting brackets are available to mount 502917 in standard EIA 19 inch rack 502917 is supplied with two mounting brackets and eight screws And please assemble according to the following steps First put the 502917 on the flat surface Locate the mounting brackets on the sides of the Switch with the mounting holes on each Next insert the screw through the bracket and into the bracket mounting holes in the 502917 Then place the Switch in to 19 inch rack Chapter 5 Installation How to connect the 502917 to PD device and existing Switch Power over Ethernet Switches Existing 104100 Ethernet Switch i SS sueo to 200 Power Cutlets PoE Switch with 1 PO port LPE 108 erasan Connect straight through twisted pair cable Cat 5 from existing Switch to the input Data port of 502917 then connect the Output Data Power port to the PD device such as Wireless AP Another switch with PD function etc Chapter 6 Technical Specifications Standards e IEEE 802 3 10Base T Ethernet e IEEE 802 3u 100Base TX Fast Ethernet e IEEE 802 3x flow control full duplex mode e IEEE 802 3af Power over Ethernet General e Media support 10Base T Cat3 4 5 UTP STP RJ 45 100Base TX Cat5 UTP STP RJ 45 e Ports 8 RJ 45 10 100 Mbps PoE ports Packet
5. i a 8 A lt 23acaaccacetanes opta ni satana A ANSI TIA EIA 568 A PLUG amp Twisted pair Cable 9 B EIAD6SA pin ASSIGNMENT cur ia 9 C Recommend CAT5 UTP Specifications 9 Chapter 1 8 Ports Power Over Ethernet Switch Introduction The 502917 is 8port Power Over Ethernet Switch consists 8 PSE Ethernet ports that is powered detecting classification capability and programmable PD disconnect sensing and with additional 8 10 100Mbps Ethernet port That solves limitation of power outlet location offer system designer flexible solution to locate network device wherever lire gt NTELUHAT Key Features e 10 100 auto sensing ports automatically detect optimal network speeds IEEE 802 3af compliant RJ 45 PSE PoE output ports Power output up to 15 4 Watts per port e All RJ 45 ports with Auto MDIX auto uplink support Supports NWAY auto negotiation Supports 8 VLAN groups port based and tagged VLAN support Supports Quality of Service QoS port based and tagged with 2 priority levels Supports bandwidth control per port Supports MAC address locking per port Broadcast storm control enable disable Store and forward switching architecture Full half duplex operation e IEEE 802 3x flow control for full duplex Zero packet loss back pressure flow control for half duplex Packet filtering forwarding rates 148 800 pps 100 Mbps 14 880 pps 10 Mb
6. ps Supports 4096 MAC address entries 128 kBytes buffer memory Desktop size metal case LEDs for power link activity and PoE Chapter 2 Package Contents Before you start to install the Switch please verify your package that contains the following items E One 8 port Power Over Ethernet Switch E Rack mount Kit For Rack Installation E One Power Cord E One User s Manual e INTELLIMTT e 1 a a n 8 Port 10 100Mbps Power Over Ethernet Switch User s Manual Power Cord 8 Port 10 100Mbps Power Over Ethernet Switch User s Manual ate POSES Note If any of these items is found missing or damaged please contact your local supplier for replacement 3 o Chapter 3 Front Panel Layout A Function of 8 RJ 45 Ports There are 8 ports RJ 45 connectors on the front panel and all ports has build IEEE802 3af PoE PSE is for the connecting with Powered Device PD device LED Display RJ 45 Port AL MTELLINET B LED Indicators of 8 Port 10 100Mps Switch LED Color Stat Description o orten ee Poweron eis PD Link Green On Portis linking to a PD device Off No PD device link to the port TA B 1 8 7 Off Portison the 10M status TC LINK ACT Green 10 100Mbps port for 1 connection Flashing 10 100Mbps for data activating 8 1 8 8 8 10 100M Green Port is on the 100M status 8 8 C LED Definitions Off i Of he data is transmitted or receive
Download Pdf Manuals
Related Search