Scosche FD1330B mounting kit
Contents
1. the stereo opening Push the brackets onto the lip on each side see Figure 1 Position the double DIN stereo or 2 DIN stereos in between the brackets from behind align the stereo s side mounting holes with the holes in the brackets and then screw VARIOUS REAR the stereo down between the brackets see illustration A SUPPORTS NO ao NOTE We recommend performing step 2494 LEFT 2 above on a table or work bench BRACKET rather than inside the vehicle Use the stereo s supplied mounting screws CAUTION Using long screws risks damage to the internal components of the double DIN unit 4 Snap in trim ring make all connections and re install radio dash bezel 2494 RIGHT BRACKET W STEREO S SUPPLIED SCREWS 2495 TRIM RING CAUTION REAR SUPPORT AVAILABLE SEPARATELY REAR SUPPORTING FIGURE 1 NOTE CUT FOR DOUBLE DIN ONLY 4 f q THE STEREO ADDS TO THE INSTALLATION S STRUCTURAL INTEGRITY CUT HERE ATTACH BRACKET TO LIP LIABILITY DISCLAIMER This instruction booklet is based on carefully documented data and research of automobile dash disassembly wire harness codes and information pertaining to installation of this kit FD1330B in 1995 2010 Ford Mercury amp Mazda vehicles Scosche Industries Inc can not be held responsible for discrepancies inconsistencies that may occur due to the automobile manufactu2. 1 3695 ext 3 FRIENDLY CUSTOMER OUR HOURS ARE SENVICE TECHNICIANS Monday Friday 8 00 a m to 5 30 p m PST YOU WON T BE ON HOLD LONGER THAN 5 MINUTES Saturday 8 00 a m to 2 00 p m PST 2010 SCOSCHE INDUSTRIES INC SI 7 10 FD1330B 3000312 FACTORY WIRING CODES For Factory Wiring Codes go to www scosche cars com CAR STEREO CONNECTORS PROVIDE EASY CONNECTION OF YOUR CAR STEREO TO FACTORY WIRING HARNESS FD16B FDK10B 1998 Up Ford 1985 Up Ford Lincoln Mercury Mazda Premium Sound PRELIMINARY STEREO REMOVAL Using the Ford DIN removal tool carefully insert into the holes on the outside edges of the stereo to release the stereo and pull it out of the dash cavity Unplug all connectors and remove the stereo Extract 2 screws in the dash bezel just above the heater air conditioning controls Carefully pry out on the dash bezel to release the fastening clips unplug any switches if equipped lighter and remove the bezel h AOON STEREO INSTALLATION NOTE This installation requires dash bezel modification because of the nosepiece height of the double DIN stereos Make note of this if you are working on a leased vehicle or the original unit is to be re installed at some future date 1 Carefully file or grind away the TOP and BOTTOM portions of the small lip around the inside of the dash bezel s stereo opening Push the 2494 left and the 2494 right brackets onto the corresponding sides of
3. SCOSCHE FD1330B IN DASH DOUBLE DIN INSTALLATION KIT FOR 1995 2010 FORD MERCURY MAZDA 2494 LEFT VEHICLE APPLICATIONS BRACKET FORD 1995 2001 EXPLORER ALL MODELS 2002 2003 EXPLORER SPORT 2001 2005 EXPLORER SPORT TRAC 1995 2010 RANGER MAZDA p 1995 2009 B SERIES PICKUP j f MERCURY pie 1996 2001 MOUNTAINEER RIGHT BRACKET 2495 TRIM RING INTRODUCTION PRELIMINARY This premium installation kit is for 1995 2010 Ford Mercury amp Mazda vehicles Included are all the parts you need to mount your car stereo or CD player into your vehicle s dash Refer to the individual instruction in this manual to remove your vehicle s factory radio and assemble the kit CAUTION DISCONNECT YOUR VEHICLE S NEGATIVE BATTERY TERMINAL BEFORE THE INSTALLATION TO HELP PREVENT ELECTRICAL DAMAGE WE RECOMMEND THE USE OF A VOLT OHM METER OVER A TEST LIGHT TO CHECK WIRING A TEST LIGHT OR GROUNDED WIRE PROBE CAN CAUSE DAMAGE TO THE VEHICLE S COMPUTER AND OR DIAGNOSTIC SYSTEMS AVOID ALL FACTORY AIRBAG WIRING AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY OR DEATH NOTES e See your vehicle s instructions for any special tools your installation might require e Read all instructions accompanying your car stereo for proper wiring and mounting instructions IMPORTANT Do Not Return Product to the Retailer IF YOU NEED ASSISTANCE OR REPLACMENT PARTS Call us FIRST at 1 800 62
4. ring changes or options or damage that may occur in the automobile during the installation of components while using this booklet
Download Pdf Manuals
Related Search