Gefen EXT-DVI-1CAT6
Contents
1. SENDER PANEL DESCRIPTIONS 5V DC Power Receptacle Connect the included 5V DC power supply between this input and an open wall power socket Power LED Indicator This LED will become active once the included 5V DC power supply is properly connected between the unit and an open wall power socket DVI Input Connector This input will accept a single DVI D digital only source for extension Attach the cable coming from your DVI source here Link RJ 45 Port This port is used to connect the sending and receiving units together using a CAT 6a cable RECEIVER PANEL LAYOUT Front Panel Back Panel RECEIVER PANEL DESCRIPTIONS Equalization Adjustment Trim Pot Control The EQ adjustment or Trim Pot is used to equalize the signal to compensate for the extension distance and the quality skew variances that are found in different CAT6a cabling brands DVI Output Connector This connector hooks up the Receiver to a DVI D compliant monitor at the remote destination 5V DC Power Receptacle Connect the included 5V DC power supply between this input and an open wall power socket Power LED Indicator The LED power indicator will become active once the included 5V DC power supply is properly connected beten the unit and an open wall power socket RJ 45 Link Port This port is used to connect the DVI Extender Sender and Receiver units together using a CAT6a cable CONNECTING AND OPERATING THE DVI OVER ONE CAT 6 EXTENDER Ho2. C Gefen DVI Over One CATG Extender EXT DVI 1CATG User Manual vw gefen com ASKING FOR ASSISTANCE Technical Support Telephone 818 772 9100 800 545 6900 Fax 818 772 9120 Technical Support Hours 8 00 AM to 5 00 PM PST Monday thru Friday Pacific Time Write To Gefen LLC c o Customer Service 20600 Nordhoff St Chatsworth CA 91311 www gefen com support gefen com Notice Gefen LLC reserves the right to make changes in the hardware packaging and any accompanying documentation without prior written notice DVI over one CAT6 is a trademark of Gefen LLC 2010 Gefen LLC All Rights Reserved Alltrademarks are the property of their respective owners Rev CONTENTS Introduction Operation Notes Features Sender Panel Layout Sender Panel Descriptions Receiver Panel Layout Receiver Panel Descriptions Connecting And Operating The DVI Over One CAT6 How to Connect the DVI over One 6 Adjusting the Signal Quality DIP Switch Configuration DIP Switch Location DIP Switch Configuration Network Cable Wiring Diagram Specifications Warranty INTRODUCTION Congratulations on your purchase of the DVI over one CAT6 Extender Your complete satisfaction is very important to us Gefen Gefen delivers innovative progressive computer and electronics add on solutions that harness integration extension distribution and conversion technologies Gefen s reliable plug and play produ
3. adiiancisy aavacbusinastiecdeneusldadnexaninesussb atanstadensdeccau 5V DC Power CONSUMPTION 10 Watts max per unit DIMENSION Seen 3 3 W x 1 3 H x 3 4 D Shipping Weight xno toccttnsaiccacanint ratico 4 lbs 13 WARRANTY Gefen warrants the equipment it manufactures to be free from defects in material and workmanship If equipment fails because of such defects and Gefen is notified within two 2 years from the date of shipment Gefen will at its option repair or replace the equipment provided that the equipment has not been subjected to mechanical electrical or other abuse or modifications Equipment that fails under conditions other than those covered will be repaired at the current price of parts and labor in effect at the time of repair Such repairs are warranted for ninety 90 days from the day of reshipment to the Buyer This warranty is in lieu of all other warranties expressed or implied including without limitation any implied warranty or merchantability or fitness for any particular purpose all of which are expressly disclaimed 1 Proof of sale may be required in order to claim warranty 2 Customers outside the US are responsible for shipping charges to and from Gefen 3 Copper cables are limited to a 30 day warranty and cables must be in their original condition The information in this manual has been carefully checked and is believed to be accurate However Gefen assumes no r
4. cts supplement cross platform computer systems professional audio video environments and HDTV systems of all sizes with hard working solutions that are easy to implement and simple to operate The Gefen DVI over one CAT6 Extender The Gefen DVI over one CAT6 Extender will send a 1920x1200 60Hz DVI D signal over a single CAT 6a cable to distances of up to 200 feet 60m Extension of high resolution computer video can now be simplified with the use of only a single CAT 6a cable Previous solutions used 2 cables to accomplish this The DVI over one CAT6 extender s pure digital transmission method insures 100 signal integrity over this single cable extension solution How It Works The Gefen DVI over one CAT6 Extender system consists of two devices a sender and a receiver The single link DVI source set top box DVD player or computer video card output connects to the sender unit with the supplied 6 foot DVI cable The receiver unit connects to a DVI compliant display One CAT 6a cable links the sender and receiver together at distances of up to 200 feet Power is applied to both the sender and receiver with the included 5V DC power supplies A perfect image is now displayed on the remote DVI display OPERATION NOTES READ THESE NOTES BEFORE INSTALLING OR OPERATING THE DVI OVER ONE CAT6 EXTENDER The DVI over one CAT6 Extender was designed for use with high quality CAT 6a augmented cabling This unit will either not perform to specif
5. esponsibility for any inaccuracies that may be contained in this manual In no event will Gefen be liable for direct indirect special incidental or consequential damages resulting from any defect or omission in this manual even if advised of the possibility of such damages The technical information contained herein regarding the features and specifications is subject to change without notice For the latest warranty coverage information please visit Gefen s Warranty web page at http www gefen com kvm aboutus warranty jsp PRODUCT REGISTRATION Please register your product online by visiting Gefen s web site at http www gefen com kvm Registry Registration jsp 14 1 6 20600 Nordhoff St Chatsworth 91311 1 800 545 6900 818 772 9100 WWW gefen com Es amp support gefen com 9 Rev fax 818 772 9120 ay Te Qu
6. ication or refuse to operate completely if cabling other than CAT 6a is used When field terminating CAT 6a cabling please adhere to the TIA EIA 568 B specification shown on page 12 for your convenience The DVI over one CAT6 has a maximum distance rating based on the bandwidth i e resolution and color of the video being transmitted When used with high quality CAT 6a cabling you may expect a maximum extension range of 200 feet 60 meters at 1920x1200 or 1080p resolution at up to a 60Hz refresh rate Lower quality cabling or older standards such as CAT5 cables will shorten the maximum achievable extension distance For CAT5e cables the maximum distance is 150ft at 1080p or 1920x1200 This product features HDCP pass through FEATURES Features e Flexible extension of single link DVI D thanks to inexpensive and widely available CAT6 cable e is transmitted digitally over the CAT6 cable for zero signal loss e Single Link Range Maximum resolution 1920x1200 60 Hz e Compliant with HDCP 1 1 and DVI 1 1 standards e Equalizes the DVI signal and retransmits it with optimal quality regardless of incoming signal quality e Eliminates equipment noise in the viewing environment e Improved compensation for CAT6 cable skew Package Includes 1 DVI over one CAT6 Sender 1 DVI over one CAT6 Receiver 1 6 ft DVI Cable M M 2 5V DC Power Supply 1 User s Manual SENDER PANEL LAYOUT Front Panel Back Panel
7. im Pot 1 Insert a small flat headed tool into the Trim Pot on front panel of the receiver unit 2 The Trim Pot has 8 set positions Turn the Trim Pot in a clockwise fashion until it clicks into the next position Continue adjusting the Trim Pot by trying all 8 positions until the issue is resolved 3 Carefully remove the adjustment tool Trim Pot DIP SWITCH CONFIGURATION DIP Switch Location On the bottom of the Receiver Unit there are four 4 DIP switches Each DIP switch performs a different function Before modifying DIP switch settings disconnect the power from the Receiver unit After the DIP switches have been configured reconnect the power Receiver Unit bottom DIP Switch 1 2 3 4 NOTE DIP switch 3 and DIP switch 4 are not used Default settings for DIP switches ON OFF 2 10 DIP SWITCH CONFIGURATION DIP Switch Settings DIP 1 EDID Management OFF Local EDID When Local EDID mode is used the EDID will be assembled by copying all video and audio features of the connected output device Deep Color support will be manually controlled using DIP switch 2 see DIP 2 Deep Color below ON Pass through EDID Allows all video and audio features of the connected devices to be passed to the source device without control over Deep Color By default the unit is shipped with DIP 1 in the ON position DIP 2 Deep Color OFF Disables Deep Color suppor
8. t Disables Deep Color in the EDID Deep Color management is only available when Local EDID is being used DIP 1 ON ON Enables Deep Color support Enables Deep Color support In Pass through EDID Mode setting DIP 2 ON has no effect since all EDID information is passed through 11 NETWORK CABLE WIRING DIAGRAM Gefen has specifically engineered products to work with the TIA EIA 568 B specification Please follow the table below when field terminating cable for use with Gefen products Failure to do so may produce unexpected results and reduced performance Blue White Brown White HE E 12345678 This product was designed for use with CAT 6a augmented cabling only This unit will either not perform to specification or refuse to operate completely if cabling other than CAT 6a is used Each cable run must consist of a single undivided segment of CAT 6a cabling from Sender to Receiver Punch down blocks or splices will not work 12 SPECIFICATIONS Maximum SOC ee 225 MHz Maximum Video Resolution 1920 1200 Input Signal 5 Volts TTL HIDE Video Signal risa 1 2 Volts OME GION DVI I 29 pin female digital only ETA SONNE ON ee RJ 45 Shielded Power Supply ass ccscedccricoctcedsasanate
9. w to Connect the DVI over one CAT6 Extender Connect a DVI D cable one is supplied between the DVI output on a source device and the DVI input connector on the DVI over one CAT6 Extender sender unit Connect a single CAT6a cable between the sending and receiver units NOTE When field terminating CAT6a cabling please adhere to the TIA EIA 568 B specification Please see page 12 for more information Connect a DVI D cable user supplied between the DVI input on a DVI compliant output device i e computer display and the DVI output on the DVI over one CAT6 Extender receiver unit Connect the included 5V DC power supplies two are included between the sender and receiver units and available power outlets Power up the DVI output device DVI computer monitor first and the DVI source device i e computer last Wiring Diagram for the DVI over One CAT 6 Extender CAT 5 CABLE DVI CABLE 7777 DVI Source I P Sender DVI Display EXT DVI 1CAT6 CONNECTING AND OPERATING THE DVI OVER ONE CAT 6 EXTENDER Adjusting the Signal Quality The DVI over one CAT6 receiver unit has a equalization device called a Trim Pot trim potentiometer to compensate for the extension distance and the quality skew variances that are found in different CAT6a cabling brands If there is no output video or if output video contains video artifacts and or video noise such as snow please use the steps below to adjust the Tr
Download Pdf Manuals
Related Search