Metra 99-8222 mounting kit
Contents
1. Radio Housing Figure B Snap the Pocket into the Radio Housing Figure C Continue to final assembly R GS a f Mena SA 99 Seee KIT ASSEMBLY DOUBLE DIN OR STACKED ISO MOUNT UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio Cut and remove the center bar from the Radio Housing Figure A Snap the Double DIN brackets to the inside edge of the Radio Housing Figure B Slide the Double DIN or stacked ISO mount units into the bracket radio housing assembly then secure it to the assembly using the screws sup plied with the units Figure C Snap the Double DIN Stacked ISO Trim Plate onto the front of the Radio Housing Figure C Continue to final assembly MZ 99 8222 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making2. INSTALLATION INSTRUCTIONS FOR PART 99 8PeeP APPLICATIONS Toyota Highlander 2008 2010 NON NAV MODELS ONLY 99 Seer 99 BA22BR KIT FEATURES e DIN Radio Provision with Pocket e SO Mount Radio Provision with Pocket e Double DIN Radio Provision e Stacked ISO Mount Units Provision e Painted to match factory dash 99 8222 Black 99 8222BR Brown KIT COMPONENTS e A Radio Housing B ISO Brackets C ISO Trim Plate D Double DIN Brackets e E Double DIN Stacked ISO Trim Plate e F Snap in Pocket G Radio Housing Brackets 4 WIRING AND ANTENNA CONNECTIONS 2 A Sold Separately o Harness a e 70 1761 Toyota interface 1987 up lt e TYTO 01 Toyota amplified interface TE harness 2003 up Antenna Adapter Not required TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool e Phillips Screwdriver Socket Set me SAN Ww Na NS gt A 1 800 221 0932 www metraonline com COPYRIGHT 2007 2010 METRA ELECTRONICS CORPORATION SRE TABLE OF CONTENTS Dash Disassembly Toyota Highlander 2008 2010 n ss 1 2 KIEETEDAFAUOM ss cameras an nais sma rust vanne tad Kit Assembly DIN Radio Provision with Pocket n nn nunnu nun nunnn14 SO Mount Radio Provision with Pocket 5 Double DIN Radio Provision 4ssssssssssvunr s Stacked ISO Mount Units Provision 0 FI
3. NAL ASSCMDNY aaneen esu vas maas esisel Note Refer also to the instructions included with the aftermarket radio KNOWLEDGE IS POWER Enhance your installation and fabrication skills by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more information and take steps toward a better tomorrow PS Oez 99 5222 DASH DISASSEMBLY TOYOTA HIGHLANDER 2008 2010 mi Disconnect the negative battery ter minal to prevent an accidental short Circuit 2 Unclip and remove the a c vent panel Figure A 69 Unclip the trim panel containing the climate controls and pocket Unplug the climate controls and remove the trim panel Figure B a Remove 4 10 MM bolts securing the B radio assembly Unplug and remove the radio assembly Figure C Continued on page 2 im Oez 99 5222 DASH DISASSEMBLY TOYOTA HIGHLANDER 2008 2010 5 Remove the 2 Phillips screws secur ing the clock display then remove the clock display from the radio assembly Retain the screws and clock display for re use during kit preparation Figure D 6 Unclip and remove the hazard switch SIDE VIEW assembly from radio assembly CLOCK DISPLAY Retain the hazard switch assembly RADIO bnn for re use during kit preparation Figure E 7 Remove 4 spring clips from the back of the radio Retain the spring clips for re use duri
4. connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition ACC Red 12V Batt Memory Yellow GIOUNG nnee Black Power Antenna Blue Amp Turn On Blue White Amp Ground Black White Illumination Orange Dimmer Orange White Right Front Gray Right Front Gray Black Left Front White Left Front White Black Right Rear Violet Right Rear Violet Black Left Rear Green LeftRear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications A 7 EZ NOTES ZE eee NOTES 99 8222 INSTRUCTIONS A 1 800 221 0932 www metraonline com REV 04 26 10 COPYRIGHT 2007 2010 METRA ELECTRONICS CORPORATION INST99 8222
5. ng kit preparation Figure F Continue to kit preparation 4 SPRING CLIPS Le 99 B222 KIT PREPARATION TOYOTA HIGHLANDER 2008 2010 1 Attach the radio housing brackets to the radio housing Note Make sure that the leg on the bracket is on the outside of the leg on the radio hous ing Figure A 2 Attach the clock display to the brack ets radio housing assembly using the factory hardware Figure B 3 Snap the hazard switch assembly into the radio housing Figure C 4 Attach the 4 spring clips to the back of the radio housing Figure D Continue to kit assembly 4 SPRING CLIPS f mens 99 8222 KIT ASSEMBLY DIN RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward Figure A 2 Slide the aftermarket radio into the DIN cage until it snaps into place Figure B 3 Snap the pocket into the radio housing Figure C Continue to final assembly Es MZ 99 8222 KIT ASSEMBLY ll A5 ISO MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio A Mount the ISO Brackets to the radio using the screws supplied with the radio Figure A Slide the radio into the radio housing until it snaps into place Figure B Snap the ISO Trim Plate onto the front of the
Download Pdf Manuals
Related Search