Metra 99-7876 mounting kit
Contents
1. Orange Left Rear Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications 5 99 7876 INSTRUCTIONS 1 800 221 0932 www metraonline com REV 7 02 10 COPYRIGHT 2008 2010 METRA ELECTRONICS CORPORATION INST99 78762. INSTALLATION INSTRUCTIONS FOR PART 99 7876 APPLICATIONS HONDA Pilot 2009 11 99 7876 KIT FEATURES e ISO Mount Radio Provision With Pocket KIT COMPONENTS e A Radio Housing B Radio Housing Brackets Wiring amp Antenna Connections sold seperatel e 70 1729 Honda Harness 2008 up e 40 HD10 Honda Antenna Adapter 2006 up TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool o Phillips Screwdriver Wire Cutters S gt SSS T G 1 800 221 0932 www metraonline com COPYRIGHT 2008 2010 METRA ELECTRONICS CORPORATION SELS TABLE OF CONTENTS Dash Disassembly HONDA Pilot 2009 11 1 2 Kit Preparation ss ss uenns weecleiersewadorsevievenreentews 3 Kit Assembly SO Mount Radio Provision With Pocket 4 Note Refer also to the instructions included with the aftermarket radio KRACHALEDGE POWER Rar art iniae yar HEA Sort ces cai dedi bey Beni PR bag ee ep RG ee Ba ke pd pee PepRARA GR RTI meme ae HE SE mnnt DA vg er Sie Be ee ued PSN en RE tor anne eager aed dee tapes tele ot btt ir E e tE Ue Vers A 29 7876 DASH DISASSEMBLY HONDA PILOT 2009 11 1 Disconnect the negative battery terminal to prevent an accidental short circuit 2 Unclip and remove the left a c vent panel surrounding the shifter Figure A 3 Unclip and remove the right a c vent panel Figure A 4 Remov
3. adio into the radio housing and secure using the hardware supplied with the radio Figure C Continue to final assembly El Oe 99 7876 FINAL ASSEMBLY FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front White Power Antenna Blue Left Front White Black Amp Turn On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination
4. e the 2 Phillips screws secur ing the pocket below the radio then unclip and remove the pocket Figure B 5 Remove 4 Phillips screws securing the radio Unplug and remove the radio Figure C Continued on page 2 K Oe A 29 7876 DASH DISASSEMBLY HONDA PILOT 2009 11 6 Remove the 6 screws retaining the 3 clip assemblies at the top edge of the factory radio climate control assembly Retain screws and clip assemblies for reuse Figure D 7 Remove 4 Phillips screws securing the factory climate control Unplug and remove factory climate control NOTE Retain 4 Phillips screws and climate control for reuse in Kit Assembly Figure E Continue to kit preparation 1 SCREW ON EACH SIDE z ize EEE PREPARATION HONDA PILOT 2009 11 Note Refer also to the instructions included with the aftermarket radio 1 Cut and remove support strut on radio A housing Figure A 2 Attach the 3 clips removed in step 6 of the disassembly to the 99 7876 radio housing using the factory hardware Figure B Continue to kit assembly a LES 99 7876 KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio 1 Attach the corresponding radio housing bracket to the radio housing Figure A then attach the climate control to the assembly using the 4 Phillips screws removed in step 7 Figure B 2 Position the aftermarket r
Download Pdf Manuals
Related Search