Metra 99-7874 mounting kit
Contents
1. TT LES 99 7874 99 7874T KIT ASSEMBLY DIN MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio Slide the DIN cage into the Radio Housing and secure by bending the metal locking tabs outward Figure A 2 Slide the aftermarket radio into the DIN cage until it snaps into place Figure B 3 Snap the pocket into the radio housing Figure C Continue to final assembly RS FC C t LES 99 7874 99 7874T KIT ASSEMBLY ISO MOUNT RADIO PROVISION WITH POCKET Note Refer also to the instructions included with the aftermarket radio Mount the ISO Brackets to the radio using the screws supplied with the radio Figure A Slide the radio into the Radio Housing until it snaps into place Figure B Snap the Trim Plate onto the front of the Radio Housing Figure C Snap the Pocket into the Radio Housing Figure C Continue to final assembly TT E LES 99 7874 99 7874T KIT ASSEMBLY A DOUBLE DIN STACKED 150 MOUNT UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Cut and remove the center bar from the Radio Housing Figure A 2 Snap the Double DIN brackets to the inside edge of the Radio Housing Figure B 3 Slide the Double DIN or stacked ISO mount units into the bracket radio housing assembly and secure the unit s to the assembly using the screws supplied with the unit s2. Figure C 4 Snap the Double DIN trim plate onto the front of the Housing Radio assem bly Figure C Continue to final assembly Mena SA 99 7874 99 7874T FINAL ASSEMBLY A FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together 6 Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent electrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red 12V Batt Memory Yellow EOUN o Black Power Antenna Blue Amp Turn On Blue White Amp Ground Black White IIlumination Orange Dimmer Orange White Right Front Gray Right Front Gray Black Left Front White Left Front Whit
3. use during kit preparation 12 Remove 4 Phillips screws securing the a c vents to the factory radio assembly and remove the a c vent from the assembly Retain the screws and a c vents for re use dur ing kit preparation 13 Unclip and remove the hazard switch passenger air bag light assembly Retain the hazard switch passenger air bag light assembly for re use during kit prepa ration 14 Remove 4 Phillips screws securing trim panel at the bottom edge of the factory radio assembly and remove the trim panel Retain the screws and trim panel for re use during kit preparation 15 Remove 9 clips from the back of the factory radio assembly Retain the clips for re use during kit prepara tion Continue to kit preparation LES 99 7874 99 7874T KIT PREPARATION HONDA ACCORD 2008 2010 1 Snap the hazard switch passenger air bag light assembly into the radio housing from front Figure A 2 Secure the a c vents into the radio housing using the factory hardware from rear Figure B 3 Secure the climate controls into the radio housing using the factory hard ware from rear Figure C 4 Secure the trim panel onto the radio housing using the factory hardware Figure D 5 Attach the clips to the back of the radio housing Figure E Continue to kit assembly eh Es N HA am LV TU 1e Jo D EN A EU OLEU NER gg 5 o 6 2 __ le E T
4. HEA Sao ces Seah dee eS Pr ae een OT DAS ne I RRS RI 2 A Go ne pabi pa EO IG RIDE da a AIE a ARE ER RE La vd qe alee er UR weed SRE evince inten abet steht certa bee biche A LES 99 7874 99 7874T DASH DISASSEMBLY HONDA ACCORD 2008 2010 1 Disconnect the negative battery ter minal to prevent an accidental short Circuit 2 Unclip and remove the trim panel from above the glove box at the right side of the factory radio Figure A 3 Unclip and remove the trim panel at the left side of the factory radio Figure B 4 Remove the 2 Phillips screws from the left and right side of the of the factory radio Figure C 5 Unclip and remove the top of the cen ter console including the cup holders Figure D 6 Remove 2 Phillips screws at the bot tom edge of the pocket assembly Figure E 7 Remove 2 Phillips screws facing up inside of the pocket below the factory radio Figure F 8 Unclip and remove the pocket assem bly Figure G Continue on page 2 A LES 99 7874 99 7874T DASH DISASSEMBLY HONDA ACCORD 2008 2010 9 Remove 2 Phillips screws facing up on the bottom of the factory radio Figure H 10 Unclip the factory radio assembly Unplug and remove the radio assem bly Figure 11 Remove 6 Phillips screws securing the climate controls to the factory radio assembly and remove the con trols from the assembly Retain the screws and Climate controls for re
5. INSTALLATION INSTRUCTIONS PART 99 7874 99 7874T APPLICATIONS Honda Accord 2008 2010 Excluding dual zone automatic climate controls 99 78 74 99 7874T KIT FEATURES e Painted To Match Factory Dash 99 7874 Charcoal 99 7874T Taupe e DIN Radio Provision with Pocket e ISO Mount Radio Provision with Pocket e Double DIN Radio Provision e Stacked ISO Mount Units Provision KIT COMPONENTS e A Radio Housing B ISO Brackets e C ISO Trim Plate D Double DIN Brackets e E Double DIN Trim Plate e F Pocket WIRING AND ANTENNA CONNECTIONS Sold Separately Harness e 70 1729 Honda harness 2008 up e 70 1730 Honda amp interface harness 2008 up Antenna Adapter D 40 HD10 Honda antenna adapter 2005 up TOOLS REQUIRED A 1 800 221 0932 www metraonline com COPYRIGHT 2008 2010 METRA ELECTRONICS CORPORATION I Maes 99 7874 99 7874T TABLE OF CONTENTS Dash Disassembly Honda Accord 2008 2010 Excluding dual zone automatic climate controls s n n aaa e nara aaa 1 2 All PTODATAUON asia ne a iata aaa 0 da 3 Kit Assembly DIN Mount Radio Provision with Pocket 4 SO Mount Radio Provision with Pocket 5 Double DIN Stacked ISO Mount Units Provision 6 Final Assembly reese iata da 0 eis Cotes ener dd 7 Note Refer also to the instructions included with the aftermarket radio RCE EDGE LS POA ER ERR ME Erro CCI
6. e Black Right Rear Violet Right Rear Violet Black Left Rear Green Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifications DS LES 99 7874 99 7874T A NOTES Pl EK MENS A 997874 99 78747 A NOTES 99 7874 99 78741 INSTRUCTIONS A 1 800 221 0932 www metraonline com REV 04 21 10 COPYRIGHT 2008 2010 METRA ELECTRONICS CORPORATION INST99 7874
Download Pdf Manuals
Related Search