Metra 95-8157B mounting kit
Contents
1. APPLICATIONS LEXUS SC SERIES 1992 2000 95 8157B KIT FEATURES e Double DIN Radio Provision e Stacked ISO Mount Units Provision e Painted Black To Match Factory Dash KIT COMPONENTS D A Double DIN Radio Housing B Double DIN Brackets C 4 8 X 3 8 Phillips Screws TOOLS REQUIRED Small Flat Blade Screwdriver Panel Removal Tool e Phillips Screwdriver Socket Set Sa N gt Sa A 1 800 221 0932 kd www metraonline com COPYRIGHT 2008 METRA ELECTRONICS CORPORATION m7 MEE TABLE OF CONTENTS Dash Disassembly Lexus SC Series 1992 2000 e 1 2 Kit Assembly Double DIN Stacked ISO Mount Unit s Provision 3 Final ASS une 4 Note Refer also to the instructions included with the aftermarket radio Br f Aen A 95 8157B DASH DISASSEMBLY LEXUS SC SERIES 1992 2000 1 Disconnect the negative battery ter minal to prevent an accidental short circuit 2 Push down on collar around base of shift knob then remove 2 Phillips screws then pull up on knob to remove Figure A oo Unclip and remove the shifter trim panel Tip Start at the front with ashtray open Figure B 4 Open cup holder lid then unclip and remove the cup holder Continued on page 2 SST Y METTS4 95 8157B DASH DISASSEMBLY n LEXUS SC SERIES 1992 2000 c Remove 6 Phillips screws securing the upper console trim panel then2. unclip and remove the panel Figure C Remove 8 screws securing the radio and climate control assembly Remove 4 screws securing the climate controls to the bracket assembly and remove the climate controls Retain the screws and cli mate controls for reuse during kit assembly Figure D Continue to kit assembly nr L Y Mena sA 95 8157B KIT ASSEMBLY LEXUS GS SERIES 1992 2000 DOUBLE DIN STACK ISO MOUNT UNIT S PROVISON Note Refer also to the instructions included with the aftermarket radio 1 amp Attach the Double DIN Brackets to the Double DIN Radio Housing using the 4 8X3 8 Phillips screws Figure A Position the factory climate controls into the Bracket Radio Housing assembly and secure using the factory hardware Figure B Slide the Double DIN or stacked ISO mount unit s into the bracket radio housing assembly and secure the Double DIN or stacked ISO mount units to the assembly using the screws supplied with the Double DIN or stacked ISO mount unit s Figure C Continue to final assembly fe Dia 2 gt 81578 FINAL ASSEMBLY en oor FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together C Solder D Tape 1 Locate the factory wiring harness in the dash Metra recommends using the proper mating adapter and making connections as shown Isolate and individ ually tape off the ends of any unused wires to prevent el
3. 95 8157B
4. ectrical short circuit 2 Re connect the negative battery terminal and test the unit for proper operation 3 Reassemble radio and dash assemblies in reverse order of disassembly FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 12V Ignition Acc Red Right Front Gray 12V Batt Memory Yellow Right Front Gray Black Ground Black Left Front White Power Antenna Blue Left Front White Black Amp Tum On Blue White Right Rear Violet Amp Ground Black White Right Rear Violet Black Illumination Orange Left Rear 0 Green Dimmer Orange White Left Rear Green Black NOTE When a Black wire is not present ground radio to vehicle chassis All colors may not be present on all leads due to manufacturer s specifictions Enjoy your newly installed radio 4 NOTES 95 8157B INSTRUCTIONS A 1 800 221 0932 ke www metraonline com REV 12 23 08 COPYRIGHT 2008 METRA ELECTRONICS CORPORATION INST
Download Pdf Manuals
Related Search