Metra 95-7510 mounting kit
Contents
1. APPLICATIONS Mazda RX 8 2004 2008 95 7510 95 7510HG KIT FEATURES Double DIN Radio Provision Stacked ISO Mount Units Provision TWO FINISHES AVAILABLE 99 7510 BLACK 99 7510 KIT COMPONENTS A Radio Climate Control Housing B Double DIN Radio Brackets C Rear Support 0 interface E Wiring Hamesses F 2 Climate Control Extension Hamesses Small Fiat Blade Screwdriver Panel Removal Tool Philips Screwdriver Socket Set Cutting Tool a 1 800 221 0932 www metraonline com COPYRIGHT 2004 2008 METRA ELECTRONICS CORPORATION 222 TABLE OF CONTENTS Dash Disassembly Mazda RX 8 2004 2008 126 Kit Assembly Double DIN Radio Provision Stacked ISO Mount Units Provision 4 Note Refer also to the instructions included with the aftermarket radio KNOWLEDGE IS POWER Enhance your Installation and fabrication skla by enrolling in the most recognized and respected mobile electronics school in our industry Log onto www installerinstitute com or call 800 354 6782 for more Information and tako steps toward a better tomorrow az 95 7510 DASH DISASSEMBI MAZDA RX 8 2004 2008 1 Disconnect the negative battery ter minal to prevent an accidental short circuit 2 Unscrew the shift knob counter clock wise to remove Figure A 3 Unclip and remove the shifter trim panel2. Figure B 4 Remove 2 Phillips screws from the bottom of the ashtray assembly then unclip and remove the assembly Figure C 5 Unclip and remove the knee panel on the driver s side under the steering column Figure D then remove 1 10 MM bolt from the side of the radio bracket Figure E Continued on page 2 az 95 7510 DASH DISASSEMBL MAZDA RX 8 2004 2008 6 Remove 2 Phillips screws from the bottom of the radio climate control panel Figure F 7 Unsnap radio climate control panel including radio chassis Unplug and remove panel and chassis Figure 8 Remove 3 Phillips screws securing the factory display harness to the radio chassis Unplug and remove display harness Retain display har ness for re use during kit assembly Figure H 9 Remove 4 screws securing the radio chassis to the radio climate control panel Figure I 10 Remove 6 screws securing the cli mate controls from the radio climate control panel Unplug and remove the climate controls Retain the screws and climate controls for re use during kit assembly Figure J Continued on page 3 az 95 7510 DASH DISASSEMBLY MAZDA RX 8 2004 2008 11 Remove 17 sorews securing the cir cuit board to the radio climate control panel to access the plug for the haz ard switch assembly Figure K 12 Remove 2 screws secur
3. included with the aftermarket radio 1 Press and hold the A G Mode button to scroll through the various kit options AMB TEMP ON or OFF AMB TEMP C or F SET TIME 12 24H and SET TEXT 2 When you see the option you want just let the button go and the action on the screen will be performed ie To turn the ambient temperature on you would scroll through until the display says AMB TEMP ON and let the button go 3 To set the time hold down the Mode button until the display says SET TIME 12 244 then let the button go 4 To switch between 12H and 24H press the front defrost button to the left of the A G Mode button 5 To change the Hour press the rear defrost button to the right of the A C Mode button 6 To change the minute press the button at the top of the A C Mode button 7 Atany time if you do not press any buttons for 5 seconds the display will save and return to the default screen and the climate control buttons will return to their normal configuration 8 If you hold the Mode button down long enough the display will say SET TEXT This will allow you customize the default text on the display 9 Once the display says SET TEXT let go and the first letter of the display will begin blinking 10 Press the front defrost button to move the cursor left and the rear defrost button to move the cursor to the right 11 You can scroll up with the A C button and down with the Recirc Fresh button through the
4. off the ends of any unused wires to prevent electrical short circuit Refer to Metra EIA Wiring Code below FINAL WIRING CONNECTIONS Make wiring connections using the EIA color code chart shown below and the instructions included with the head unit Metra recommends making connections as shown below Strip Splice Solder Tape Isolate and individually tape off ends of any unused wires to prevent electrical short circuit METRA EIA WIRING CODE 129 Ignition Act Red Gray 129 Batt Memory Yellow Gray Black Ground Black White Power Antenna Blue White Black Amp Turn On Blue White Violet Amp Ground Black White Violet Black lumination Orange Green Dimmer Orange White Green Black NOTE When a Black wire is not present ground radio to vehicle chassis colors may not be present on all leads due to manufacturer s specifications Continued on Page 6 m ALT 95 7510 FINAL ASSEMB Continued from Page 5 WARNING FAILURE TO INSERT THE HVAC CABLES INTO THE CORRECT LOCATION WILL CAUSE DAMAGE TO THE INTERFACE AND MAKE THE DISPLAY AND HVAC CONTROLS NOT FUNCTION PROPERLY 2 Attach the 2 climate control extension harnesses to the temperature control cable and the fan control cable on the factory climate control 3 Plug the Temperature Control cable from the factory climate control into the port on the interface that reads TEMP 4 Plug the Fan Control cable f
5. ing the haz ard switch to the radio climate control panel Unplug and remove hazard switch Retain the screws and hazard switch for re use during kit assem bly Figure L Continue to kit assembly m LES 95 7 ASSEMBI DOUBLE DIN RADIO PROVISION OR STACKED ISO MOUNT UNITS PROVISION Note Refer also to the instructions included with the aftermarket radio 1 Cut the top 2 mounting locations off of the climate controls to provide clearance for the aftermarket radio Figure 2 Secure the climate control to the radio climate control housing using 4 of the factory screws removed in step 10 of the dash disassembly Figure B 3 Secure the hazard switch assembly to the radio climate control housing using the factory screws removed in step 12 Figure B 4 Attach the Double DIN brackets to the Double DIN or stacked ISO Mount unit s using the hardware supplied with the unit s Figure C 5 Attach the rear support to the unit s using the hardware supplied with the unit s Figure D Continue to final assembly ALL 95 7510 F ASSEMBI FINAL ASSEMBLY A Strip wire ends back 1 2 B Twist ends together 6 Solder D Tape 1 Locate the factory wiring harness in the dash Use the supplied wire harnesses and make the connections as shown Isolate and individually tape
6. rom the factory climate control into the port on the interface that reads FAN 5 Plug the Display cable removed in step 8 of the dash disassembly into the port on the interface that reads DISP 6 Plug the Hazard Switch extension cable into the end of the hazard switch and the other end of the extension cable into the port next to the DISP port ma HAZARD Continued on Page 7 mer 95 7510 FINAL ASSEMBLY Continued from Page 6 OBDII CONNECTOR FACE VIEW PINK WIRE PINK BLUE WIRE When using the Nav features of the interface you will need to connect the 2 pin harness and run the 2 wires to the OBDII connector and connect them in the position shown Figure A 8 The following wires on the 10 pin hamess are for the aftermarket radios that have navigation built in A Connect tte green wi to the parking trake wire of the aftermarket navigation radio Connect tte pink blue wire to the VSS or speed sense wie of the aftermarket navigation radio 6 Connect the green purple wire to the reverse wire of the aftermarket navigation radio NOTE Reverse output is NOT present on manual transmission vehicles 9 Re connect the negative battery terminal and test the unit for proper operation 10 Reassemble radio and dash assemblies in reverse order of disassembly 95 7510 KIT ASSEMBI DISPLAY CUSTOMIZATION Note Refer also to the instructions
7. various alpha numeric and symbol characters 12 When you are finished entering your text if you do not press any buttons for 5 sec onds the display will save and return to the default screen and the climate control buttons will return to their normal configuration 177 70 NOTES 95 7510 B 1 800 221 0932 www metraonline com REV 10 30 08 COPYRIGHT 2004 2008 METRA ELECTRONICS CORPORATION INST95 7510
Download Pdf Manuals
Related Search