Omnitron iConverter GX/TM2
Contents
1. Left Switch Factory Default a swe sw7 sws Link Mode Selection AN Man Link Segment LS aw Fiber Auto Negotiation Fiber Manual Negotiation Len cen Lel Factory Default sw2 AN Man Right Left Left Link Propagate LP UTP Auto Negotiation UTP Manual Remote Fault Detect Link swa 1000 10 100 Let Right Let segment RFD LS UTP 1000Mbps UTP 10 100Mbps Remote Fault Detect Link sw4 100 10 Right Right on Propagate RFD LP UTP 100Mbps UTP 10Mbps Left Left Right Symmetrical Fault Detect SFD sw5 FDX HDX UTP Full Duplex UTP Half Duplex Right Left Right Asymmetrical Link Propagate g gal Port 1 to Port 2 ALP P1 P2 SW6 l Asymmetrical Link Propagate sw7 See Link Mode Selection Left Right Right port 2 to Port 1 ALP P2 P1 SW8 Right Right Right Pass Remote Link Fault PRLF Figure B DIP Switch Bank 1 SW2 SW3 SW4 SW5 Function The UTP port is set to auto negotiation with the following modes advertised mw 1000 100 or 10 FDX 4000F 1000H 100F 100H 10F 10H The UTP port is set to auto negotiation with the following modes advertised AN 1000 100 or 19 HDX I 4000H 100F 100H 10F 10H The UTP port is set to auto negotiation with the following modes advertised AN HERIOL ADG POA 100F 100H 10F 10H The UTP port is set to auto negotiation with the following modes advertised AN2. chassis front Verify the Pwr LED is ON indicating the chassis is powered b When using a GX TM2 SFP model 8939N 0 insert the SFP Fiber transceiver into the Port 1 SFP receptacle on the GX TM2 NOTE The release latch of the SFP Fiber transceiver must be in the closed position before insertion c Connect an appropriate multimode or single mode fiber cable to the fiber port of the installed module It is important to ensure that the transmit Tx is attached to the receive side of the device at the other end and the receive Rx is attached to the transmit side Single fiber SF media converter models operate in pairs The Tx wavelength must match the Rx wavelength at the other end and the Rx wavelength must match the Tx wavelength at the other end d Connect the UTP port via a Category 5 cable to a 10BASE T 100BASE TX or 1000BASE T Ethernet device 3 CONFIGURE MODULE VIA COMMAND LINE INTERFACE To access the Command Line Interface CLI connect the GX TM2 RS 232 Console Port to the COM port of a computer equipped with terminal emulation software such as HyperTerminal The Console Port DCE is a mini DIN 6 female connector which can be changed to a DB 9 connector with the included adapter The GX TM2 Console Port is a standard asynchronous serial interface Start HyperTerminal and select the correct COM Port in the HyperTerminal Connect To window Set the serial port to the following Bits Per Second 57 600 Parity
3. 10 100 100 HDX 100H 10F 10H AN 10 100 10 FDX The UTP port is set to auto negotiation with the following modes advertised 10F 10H AN 10 100 10 HDX ee UTP port is set to auto negotiation with the following modes advertised The UTP port is set to auto negotiation with the following modes advertised MAN 1000 100 or 10 FDX 1000F 1000H 100F 100H 10F 10H The UTP port is set to auto negotiation with the following modes advertised MAN I000 tO ora MDX 4000H 400F 100M 10F 10H MAN 40 100 100 FDX p port is set to manual negotiation and is forced to MAN 10 100 100 HDX otal port is set to manual negotiation and is forced to MAN 10 100 10 FDX pi UTP port is set to manual negotiation and is forced to MAN 10 100 10 HDX D UTP port is set to manual negotiation and is forced to Figure C UTP Configuration Matrix SW6 SW7 SW8 LINK MODES These three DIP switches configure the link mode settings It is recommended to have link modes DOWN default during the initial installation After the circuit has been tested and operational configure the module for the desire mode For detailed information on the operation of the different Link Modes download the application note 7Converter Link Modes available on Omnitron s web site DIP SWITCH BANK 2 SW1 SW2 BACKPLANE ENABLE When the DIP switch is in the LEFT DS position factory default the Backplane Page 2 Port of the GX TM2 is isolated fr
4. NONE Stop Bits 1 Hardware Flow Control NONE Data Bits 8 M SL SL Master Slave Auto Select Slave Mode Only Page 3
5. Once connected press lt ENTER gt to bring up a command line prompt on the attached PC Management Options iConverter Serial Agent Network Management 1 Chassis and Module Management 2 Set Module Name Preferences Management Module Preferences IP and Control Preferences SNMP Preferences Abandon Preference Changes Save Preference Changes Restore Factory Defaults Restart Management Module Other Networking Features Management Module Maintenance 10 Firmware Update 11 Set Date Time IP Address 192 168 1 220 Chassis Number 1 Enter Choice lt H gt elp E lt xx gt it gt Figure E Command Line Interface Menu Options The CLI interface allows for the detailed configuration of the module It is recommended to configure the module with an IP address associated with the attached network Also SNMP traphost address should be configured if the module is managed with an SNMP based Management System LED Function See the GX TM2 User Manual for Legend Color Off State On Blinking State complete info rmation Power Pwr Green No power On Module has power On Power available from 4 VE RI FY O P E RATIO N Power Supply Green er installed Power Supply X Status X Blinking No power available from installed installed Power Supply X Once the module has been installed and configured per steps 1 3 verify 1000mbps i i i Fiber Optics Green No Fiber Link the module is operational
6. by viewing Fo On Fiber Link Blinking Fiber Data Activity the LED indicators EEA Management Chassis in Slave On Chassis Master Mode The Power LED indicates the module Master Slave Green Mode Blinking Operating in OAM Mode is receiving power from the chassis UTP port The Fiber Optic link LED indicates soos Giesi Marae Wei Une Das accra the fiber optic connection has been i PIT ben Not linked at On UTP linked at 1000Mbps En p LED indicates the ae Green 1000Mbps Blinking UTP Data Activity module has established a connection a Green Not linked at On UTP linked at 10Mbps across its UTP port 400 1000 10Mbps Blinking UTP Data Activity A Green Pe m On EE Up en when any UTE EDX link is active nie selves Form 040 8920N 002 C 9 10 Figure F LED Indicators Omnitron Systems Technology 140 Technology Dr 500 Irvine CA 92618 949 250 6510 tel 949 250 6514 fax www omnitron systems com osr Omnitron Systems Technology Inc iConverter GXITM2 Plug in Module QUICK START GUIDE The iConverter GX TM2 Plug In media converter and Network Interface Device NID provides 10BASE T 100BASE TX or 1000BASE T UTP to 1000BASE X fiber media conversion The GX TM2 has built in Operation Administration and Maintenance OAM functionality enabling the GX TM2 to operate as a managed demarcation point at the customer premises and network edge offering Quality of Service capab
7. ilities The GX TM2 module can be managed using NetOutlook SNMP Management Software third party SNMP Client Telnet or the Command Line Interface CLI For the complete User Manual on this product access Omnitron s secure download site and request access http www omnitron systems com login php INSTALLATION PROCEDURE 1 Configure DIP Switches 2 Install Module in Chassis and Connect Cables 3 Configure Module via Command Line Interface 4 Verify Operation 1 CONFIGURE DIP SWITCHES DIP SWITCH BANK 1 SW1 FIBER AUTO MANUAL NEGOTIATION AN MAN When this DIP switch is in the LEFT AN position factory default the fiber optic port automatically determines the duplex and pause modes of the connecting fiber Switch 1 Eee optic device If the connecting fiber optic Bank2 L Switch 4 eee device cannot provide the proper signal _ _ an to indicate its own mode of operation the DIP switch should be set to the RIGHT fiber optic Man position When Port 1 is set to 1000X manual mode no capabilities are advertised NOTE The fiber optic port of the GX TM2 is always in Full Duplex mode Switch 8 Figure A DIP switch Locations SW2 SW3 SW4 AND SW5 UTP CONTROL DIP switches SW2 SW3 SW4 and SW5 control the setting of the UTP port See Figure C for the UTP Configuration matrix NOTE Refer to the table in Section 3 2 1 2 of the GX TM2 User Manual for the more detailed information Page 1
8. om the chassis Ethernet Backplane When this Switch Left Factory Default Right DIP switch is in the RIGHT EN position SW1 A DS Port A Disabled A EN Port A Enabled the Backplane Port is enabled This sw2 B Ds PortBDisabled B EN Port B Enabled allows Ethernet Backplane connectivity sw3 to an adjacent module via the chassis Backplane Link A or B depending on SW4 Reserved Reserved the switch setting Figure D DIP Switch Bank 2 SW3 MASTER SLAVE When the GX TM2 module is installed in a chassis with an iConverter management module such as a 10 100M2 set the DIP switch to the LEFT M SL position factory default the assignment of mastership is automatically negotiated by the installed management modules To designate the GX TM2 module as the master of the chassis set the DIP switch on the module to the LEFT M SL position and set the DIP switch on the other installed management modules to the RIGHT SL position to enable Slave Only mode SW4 RESERVED This DIP switch is for factory use only and must always remain in the LEFT position factory default 2 INSTALL MODULE IN CHASSIS AND CONNECT CABLES a Carefully slide the module into an open slot in the chassis Align the module with the installation guides and ensure that the module is firmly seated against the backplane Secure the module by fastening the front panel thumbscrew push in and turn clockwise to tighten to the
Download Pdf Manuals
Related Search