Olympia CC 201
Contents
1. 13 Key descriptions C Key Use to CLEAR the batch number and counting number display DEN key By this Key the reference level for two sheet Double Note detection can be changed according to the degree of density of the notes to be counted refer to page 6 for more information ADD key By this key the ADD function is selected or cleared Code key Use to select the multi function key or the number key When Code key is ON the multi function key is selected And the number key is available when the code key is OFF Speed key Use to set the counting speed UV key Option When Code key is ON the key 1 is used to set the UV function ON or OFF and select the UV detection sensitivity MG Key Option When code key is ON the key 4 is used to set the Magnetic response sensitivity DD Key Option When code key is ON the key 7 is use to set the Size detection function MACHINE SPECIFICATIONS Ambient Temperature 0 C 40 C Ambient Humidity 30 80 Hopper capacity Maximum 200 notes Stacker capacity Maximum 200 notes Size of countable note 50x100 100x185mm Thickness of countable note 0 06 0 2mm Batch preset number display Three Digits LED small Counting number display Four Digits LED large Power source AC96V AC240V 50 60Hz Power consumption lt 50W Dimensions 276mm X 238mm Xx 250mm Weight 4 8kg Counting speed e SPEED1 700 notes2. Thread Detection feature press the THD key once again the indicator extinguishes Start Counting For trouble free counting perform these simple sequential steps before use e Select the appropriate machine settings for the notes that to be counted e Remove and retain if required all clips rubber bands paper bands and tags from the notes e Fan the bundle of bank notes to loosen them This is especially important with new motes e Feed the notes correctly in accordance with the bank note Drop Operation illustration placed on the top of the unit Please ensure you put smaller sized notes at the centre of the Hopper 5 CLEANING AND MAINTENANCE Many of the sensors that applied on this machine are optical devices These are used to detect the presence of notes in the Hopper notes in the Stacker or are used in the bank note counting process Consequently paper particles dust dirt etc may cause miscounting or in a serious condition failure of the start up internal self testing procedures Notes e NEVER attempt cleaning the machine when machine is power on Always totally disconnect the unit from the mains supply e Do NOT use chemicals for cleaning the machine e To keep the machine in good condition it is necessary to clean all the sensors with a clean dry brush Ideally cleaning is recommended at the end of each working day e The Top Cover of the unit carrying the bank note drop loading illustration can
3. be removed for access cleaning Only ever attempt this with electrical power removed from the machine e No parts of this unit are maintainable by the user The use of any oils or greases on any of the feed mechanism rubber component parts could seriously effect the operation of the unit and must be avoided at all costs 6 REMOVING THE CAUSE OF ERRORS When an error occurs an Error Code is shown on the Batch Number Display Using the Error Code chart below remove the cause according to the following remedial procedures Error Meaning Cause Remedy Code Ej A jam has Note s Remove the notes in the Hopper The occurred jammed in the machine may clear itself If not TURN machine POWER OFF and remove the jammed note s by hand EH Half size banknote Make sure guiding the small size banknote passed banknote in the centre of the hopper through only Compare the last banknote in the one counting stacker re counting all the banknotes sensor Ed A double 2 notes are bank note detected as 1 has been note print detected density is different from a standard Remove all the notes in the Stacker note Press the START key to clear the Error Ec Chainnote Notes message Recount all the notes again has overlapping occurred Adjust Thickness Eo The Batch The count is over result is larger than the Batch setting CF1 Suspected Counterfeit Remove and check the suspected CF2 note s suspected note
4. C500 Series CURRENCY COUNTER USERS GUIDE Version 1 0 Edition Initial Issue April 2006 FORWARD This Users Guide has been compiled to provide complete instructions for operating the machine Before starting please read this document thoroughly to familiarise yourself with all the functions and operations of the unit Thank you CONTENTS COVER PAGE 1 FORWARD CONTENTS This Page 2 SAFETY INSTRUCTIONS 3 EXTERNAL APPEARANCE 4 MACHINE SPECIFICATIONS 6 MACHINE OPERATION 7 CLEANING AND MAINTENANCE 11 REMOVING THE CAUSE OF ERRORS 12 ACCESSORIES SUPPLIED 13 1 SAFETY INSTRUCTIONS WARNING This Currency Counter will start counting automatically under certain circumstances Consequently for your safety it is very important that you always follow these simple precautions e The machine apply optical sensors Please keep the instrument out of direct sunlight and away from any equipment that generates magnetic fields e Do not wear loose clothing or jewellery whilst operating the Currency Counter e Do make sure that your hair does not touch the Currency Counter e Do not touch the counted currency in the Stacker area until after the machine stops processing e Turn OFF external mains power before performing maintenance or undertaking error corrections that require you to put your hand s within the machine e Do not operate the Currency Counter if you or it are damp Operating the Currenc
5. Key as follows in case the error message Ed is displayed frequently For notes that are stained or printed dark set the level indicator to illuminate in the darker position For notes that are new or lightly printed set the indicator to illuminate in the lighter position MISCOUNTING IS POTENTIALLY POSSIBLE IF YOU DO NOT HAVE THE CORRECT DENSITY SETTING LEVEL SELECTED Select the Count Mode This model machine can work in two ways In Free Count mode and Batch Count mode The Count mode can be selected by setting the batch number Free Count Mode In this mode the machine counts all notes in the Hopper without stopping This count mode will be set in case the blank is selected on the Batch Number Display by pressing the C Key Batch Count Mode In this mode the machine counts out a batch of notes that you have preset This Count mode will be set by selecting a desired number on the Batch Number Display Before beginning the count turn off the code key and used the number Key Pad to set the desired number and then begin counting normally Notes The next count session will be started automatically when you remove the counted batch of notes from the Stacker If the counting stops in the case when the preset number has not been reached whilst all the notes have been counted just refill the Hopper The machine will continue counting automatically ADDition counting function U
6. minute e SPEED2 1200 notes minute e SPEED3 1600 notes minute 4 MACHINE OPERATION BEFORE TURN ON THE MACHINE PLEASE MAKE SURE THE POWER CORD IS GOOD CONNECTION AND PROPER GROUNDING Turn the Power Switch ON Ensure the Hopper is empty Turn the Power Switch ON the Currency Counter will automatically start running for about 1 Second providing no banknote is in the Hopper upon finishing machine self diagnostic tests the machine will show 0 in the 4 digit display area and 100 in the 3 digit display These show that the machine is ready to begin counting If an Error does occur the machine will display the relative Error Message see page 11 for details although this is most often caused by a blocked optical sensor Principle causes for this blockage are by a piece of paper or dust accumulation Please refer to the Cleaning and Maintenance section page 10 to follow the actions required Whenever completed cleaning please restart the machine again Check the two note Density Double Detection level and select an optimum setting Three Density Double Detection levels are available with this machine all of which are manually selected Be sure to select an appropriate density level to ensure the machine work normally The density level settings that you selected will be memorized in the unit and will be restored as the last settings when power is restarted Change the Density level by pressing the DEN Level
7. nder the ADDition function the accumulative total is shown on the Counting Number Display Press the ADD Key to select this function with the ADDition indicator lit To clear this function press the ADD Key once again This clears the ADD indicator Setting the Thickness Adjustment Screw The Thickness adjustment Screw is set at the default position by the factory However it must be slowly and carefully adjusted in the following manner Large movements should not be necessary Ifthe Ec Chain or the Ed Double Error message occurs frequently slowly and carefully turn the Thickness Adjustment Screw in a counter clockwise direction loosen If the feeding operation does not go smoothly slowly and carefully turn the Thickness Adjustment Screw clockwise tighten Counterfeit Detection Functions Optional Throughout these optional detection functions the machine will stop when a counterfeit note is detected Ultraviolet UV Detection Function Optional A counterfeit note that generates extra fluorescence when under the UV light source can be detected if this function is selected The machine will stop with the Error message CF1 shown on the Batch Number Display under this condition The UV Detection Function can be selected by press the UV Key when the code key is ON the sensitivity of the UV function can be selected at the same time Notes Three different UV sensitivities can be selected on this model U 3 i
8. s If genuine adjust the relevant CF3 sensitivity too detection sensitivity to a lower setting high CF1 UV CF2 MG CF3 THD E10 Hopper Sensor fault Remove all bank notes E11 Stacker Sensor s TURN POWER OFF Sensor fault dirty or Thoroughly clean all the optical E20 Left Count covered by sensors Sensor fault Paper or E21 Right Count damaged If these actions do not cure the Sensor fault problem please contact your supplier E30 Encoder for further assistance fault 12 7 ACCESSORIES SUPPLIED Power Cord 1 item Users Guide 1 booklet In the interests of our ongoing policy of continual product improvement specifications are subject to change without prior notice
9. s the highest and U 1 is the lowest sensitivity Sequentially pressing the UV key will select the sensitivity The machine will stop whenever a suspected counterfeit note is detected take the suspect note out from the Stacker for detailed checking Press the START key to clear the Error message and recount all of the notes once again MG Detection Function Optional Through the MG function the unit can detect suspected counterfeit notes that are lacking the magnetic ink or metallic thread properties When a suspected counterfeit is detected the machine will stop with the Error Message CF2 displayed The MG Detection function is enabled by pressing the MG key when the code key is ON and a small indicator will also illuminate To disable the 9 MG Detection press the MG key once again the light will also extinguish Note When the machine stops whenever a suspected counterfeit note is detected take the suspect note out from the Stacker for detailed checking Press the START key to clear the Error message and recount all of the notes once again Thread THD Detection Function Euro Currency Only Optional The machine can detect suspected counterfeit notes that do not have the correct security thread features When a suspected bank note is detected the machine will stop and display the CF3 Error message The Thread detection function is selected by pressing the THD key when the code key is ON To disable the
10. y Counter under wet or damp conditions can lead to an electrical shock hazard that might result in serious injury or death e Use only the same type and rating when replacing a Fuse Using an incorrect Fuse can result in a potential fire hazard if a higher rating fuse is used e Ensure that both the machine and the domestic mains supply system are of the same voltage An incorrect supply voltage could lead to a potential fire hazard being created 3 2 EXTERNAL APPEARANCE SPEED 1 Hopper Banknotes to be counted are placed 2 Stacker The counted bank notes are stacked 3 Thickness Adjustment Used to ensure a smooth counting operation 4 Power Switch Used to turn main power ON or OFF 5 Power Inlet The Electrical Power Cord should be connected to the power inlet providing a reliable AC power supply 6 Fuse holder AC fuse inside Use the same capacity fuse for replacement 7 Banknote Guider To guide the banknotes in the centre for smooth counting 8 Display LEDs display 9 Keyboard A set of numerical and multi function keys Used to preset batch sizes up to 3 digits and the detection function 10 Density Indicator Three steps of the density sense Refer to page 6 for more information 11 Count Display Used to display the counting results up to 4 digits 12 Preset display Used to display the preset batch number and or the Error messages up to 3 digits
Download Pdf Manuals
Related Search