Barco MDRC-2124
Contents
1. Level Jumps to the level submenu see below ometry submenu Name Description Clock Allows to manually adjust the sampling Frequency frequency of the DVI analog image Clock Phase Allows to manually adjust the sampling phase of the DVI analog image Description Horizontal Allows to manually adjust the horizontal Position position of the DVI analog image Vertical Allows to manually adjust the vertical Position position of the DVI analog image Level submenu Name Description Contrast Allows to manually adjust the image contrast target of the DVI analog image Brightness Allows to manually adjust the image brightness target of the DVI analog image Setting submenu Name Description Language Allows to select another language for the OSD menus DPMS Allows to switch the display power management system on off The DPMS system will power down the display when the connected computer is left idle for a certain time Barco recommends to switch DPMS on and to use a good Windows screensaver to prevent image burn in image retention on the LCD panel 27 LED Description Allows to switch the power LED s on state on off The LED s orange DPMS state is not influenced by this setting So when the display goes into power saving mode the LED will turn orange even if it was switched off by this setting OSD2. KCC ccc BSMI CE EN60601 1 UL 60601 1 c UL CCC KCC Safety BSMI Mechanical characteristics Display dimensions W x H x D Landscape w o pedestal 579 x 382 x 106 mm Display weight With Stand 15 4 kg W Touch Without Stand 10kg Display stand Tilt height amp swivel Power requirements External DC Power Supply 90V 264V 50Hz 60Hz Standby Power lt 1W Power consumption 100 Watts Environmental Operating T min max 0 to 35 C Humidity 5 90 no condensation 34 Compatibility modes Standard Resolution Vertical Horizontal Refresh Scan kHz Hz IBM VGA 640x480 60 31 5 VESA VGA 800x600 60 37 9 VESA XGA 1024x768 60 48 4 VESA XGA 1152x870 60 54 36 VESA SXGA 1280x1024 60 63 96 UXGA 1600x1200 60 75 1920x1080 60 70 2 1920x1200 60 74 1 35 Regulatory Compliance Canada European Union United States This display has been tested MEDICAL EQUIPKENT v VITE RESPECT TO ELECTRIC SHOCK and found to comply with C Ug FIRE AND Mecuanrcat mazaros OM IEC UL EN 60601 1 and IEC JN ACCORDANCE WITH UL 60601 1 AD 60601 1 2 standards arid is 35DJ certified to meet medical standard UL 60601 1 and CAN CSA C22 2 No 601 1 C US Mark which are related to electrical shock fire and mechanical hazards only as shown on right UL mark on this page The medical display in addition to meeting medical re
3. Barco nv MID is entitled not to perform warranty repairs and terminate the warranty agreement Any actions that have been taken by Barco nv MID in this respect may be invoiced to the Customer at normal pricing ARTICLE 4 REMEDIES UNDER WARRANTY a Hardware If during the Warranty Period a Product or any part thereof fails to meet any of the Warranties then upon Customer s request Barco shall at its sole option and cost promptly and within 20 working days either i repair or correct the Product or part in question or ii replace the Product or supply part s or component s according to the terms and conditions contained in article 1 A replacement part shall be at least functionally equivalent to the original part The replaced Product parts and or components shall become the property of Barco and shall at Barco s request be returned by Customer to Barco at Barco s cost b Software Barco s sole obligation shall be to rectify substantial malfunctions of the software to the extent technically reasonably possible by amending the software or supplying an alternative 44 version of the software c The repair or replacement under the Warranties covers the cost of material and labor ARTICLE 5 DISCLAIMER OF WARRANTIES BARCO NV MID DISCLAIMS ALL WARRANTIES EXPRESSED OR IMPLIED INCLUDING ALL IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARTICLE 6 LIMITATION OF LIABILITY BARCO NV MID SHA
4. MENU 29 Appendix te I ien err LERRA dente 30 Troublesliooting toten ttem da 30 Warning Signal 31 Product dimensions 32 Technical specifications 33 Compatibility modes 35 Regulatory Compliance sse 36 Preface Important notice Notice Although every attempt has been made to achieve technical accuracy in this document we assume no responsibility for errors that may be found Our goal is to provide you with the most accurate and usable documentation possible if you discover errors please let us know Barco software products are the property of Barco They are distributed under copyright by Barco N V for use only under the specific terms of a software license agreement between Barco N V and the licensee No other use duplication or disclosure of a Barco software product in any form is authorized The specifications of Barco products are subject to change without notice Trademarks All trademarks and registered trademarks are property of their respective owners Environmental information Disposal Information The lamps inside the display contain mercury Do not throw the display in the trash Dispose of it as required by local ordinances or regulations This equipment has required the extraction and use of natural resources for its production It may contain hazardous substances for health and environment In order to avoid the d
5. Settings Jumps to the OSD setting submenu see below Factory Reset Allows to reset the default factory settings in all OSD menus As a consequence all user settings including the user presets and user profiles will be erased and the display will restart OSD setting submenu 28 Name OSD Timeout Description Allows to adjust the OSD timeout as desired When selected the OSD will automatically disappear when the display controls are left idle for the time selected Horizontal OSD Position Allows to adjust the horizontal OSD position Vertical OSD Position Allows to adjust the vertical OSD position OSD Direction Allows to switch the OSD orientation from landscape to portrait and vice versa Information menu Name Description Display Name Indicates the display type FW Version Indicates the current internal firmware version Serial Nr Indicates the display serial number Backlight Indicates the total time the display has been Runtime operating excluding the time in stand by System Hours Indicates the total time the display has been operating including the time in stand by 29 Appendix Troubleshooting If you are experiencing trouble with the LCD display refer to the following troubleshooting If the problem persists please contact your local dealer or our service center Problem No image appears on screen Che
6. LL NOT UNDER ANY CIRCUMSTANCES BE LIABLE TO CUSTOMER OR ANY THIRD PARTY FOR DIRECT INDIRECT INCIDENTAL SPECIAL OR CONSEQUENTIAL DAMAGES SUCH AS BUT NOT LIMITED TO DAMAGE TO OR LOSS OF TANGIBLE OR INTANGIBLE PROPERTY OR EQUIPMENT LOSS OF PROFITS OR REVENUES COST OF CAPITAL COST OF PURCHASE OF REPLACEMENT GOODS OR CLAIMS OF CUSTOMERS OF USER FOR SERVICE INTERRUPTIONS THE LIABILITY OF BARCO NV MID FOR MANUFACTURING SALE DELIVERY RESALE INSTALLATION OPERATION OR SUITABILITY FOR USE OF ANY PRODUCTS OR SERVICES COVERED BY OR FURNISHED UNDER THIS WARRANTY CONDITION WHETHER ARISING OUT OF CONTRACT NEGLIGENCE STRICT TORT WARRANTY OR OTHERWISE SHALL BE LIMITED TO THE REPAIR OR REPLACEMENT OF THE PRODUCT OR ANY PART THEREOF WHICH SHALL BE AT CUSTOMER S SOLE OPTION AND COST BARCO S LIABILITY SHALL NOT EXCEED THE PRICE OF THE ITEM OR ITEMS OF GOODS OR SERVICES UPON WHICH SUCH LIABILITY IS BASED ARTICLE 7 FORCE MAJEURE Either party shall be released from performance of its obligations under this agreement to the extent and for so long as the performance of this agreement is impeded by reason of force majeure For the purposes of this clause the expression force majeure means but shall not be limited to industrial dispute fire mobilisation requisition embargo currency transfer prohibitions insurrection lack of means of transport restrictions of the use of energy and generally any circumstances which are beyond the control of the
7. MDRC 2 124 User manual Copyright notice This document is copyrighted All rights are reserved Nor this document nor any part of it may be reproduced or copied in any form or by any means graphical electronic or mechanical including photocopying taping or information storage and retrieval systems without written permission of Barco 2010 Barco N V All rights reserved Table of Contents Table Of Cortents ire enti aie 4 HI 5 Important NOTICE 2 ttt tete ette 5 Environmental information 6 Safety Instructions 7 Recommendations for using your display system 10 Unpacking and handling tips 11 Preventing fire and injury 12 Cleaning the display 13 Shipping storing the display 13 Explanation of symbols sse 14 Tao EE 15 About the product 15 Package Ovie Wairi cce cet re tete e ee p nace 16 Display parts controls and lt 17 Front VIQW EET 17 Back VIEW 18 EG E 19 Connecting the display 19 Adjusting the display position 21 On Screen Display Menus 22 How to use the 050 Menus 22 OSD menus OVEF VIEW in 23 Input selection MENU 23 Adjustments MENU 24 Information
8. N IEC 60601 1 shall be kept outside the patient environment as defined in the standard Equipment not complying with IEC 60601 must be kept outside the patient environment as defined in the standard as at least 1 5 meters from the patient or the patient support Any person who connects external equipment to signal input signal output or other connectors has formed a system and is therefore responsible for the system to comply with the requirements of IEC 60601 1 1 If in doubt speak with a qualified technician In locations where 240V outlets are used connect this display only ona center tapped 240V single phase supply Water and moisture Never expose the display to rain or moisture Never use the display near water e g near a bathtub washbasin swimming pool kitchen sink laundry tub or a wet basement Ventilation Do not cover or block the ventilation openings in the cover of the set When installing the display in a cupboard or another closed location heed the necessary space between the set and the sides of the cupboard Installation Place the display on a flat solid and stable surface that can support the weight of at least 3 displays If you use an unstable cart or stand the display may fall causing serious injury to a child or adult and serious damage to the equipment Recommendations for using your display system 1 Optimize the lifetime of your display Enabling the Display Power Management Sys
9. ON Changes or modifications to this equipment not expressly approved by the party responsible for compliance could void the user s authority to operate the equipment Other countries Japan VCCI level B Korea level B PRC CCC level B Taiwan BSMI level B 40 BARCO MID GENERAL WARRANTY TERMS AND CONDITIONS Applicable from Jan 1st 2008 ARTICLE 1 PRODUCT WARRANTY Barco nv Medical Imaging Division warrants that the equipment will be free of defects in workmanship or material for the warranty period or the specific period of a warranty extension program Hardware Barco warrants that upon delivery hereunder the Products shall i conform to its specifications in effect at the date of delivery and ii be free from defects in material and workmanship the Warranties Software Barco warrants that software written by Barco shall perform substantially in accordance with the specifications in effect at the date of delivery Software is inherently susceptible to bugs and errors Barco makes no warranties with respect to the software which is provided to Customer on an as is basis and does not warrant uninterrupted or error free operation of the Products Unless otherwise indicated in Barco s web site or in the agreement between Barco and Customer the Warranty Period shall be a Hardware 12 months commencing on the Barco date of invoice b Software 3 months commencing on the Barco date of invoice Notwithstanding
10. actory Calibrated Luminance Eg1 display is used at 8 hours day ie 2 920hours year The display system is covered with warranty period of 5 year The Guaranteed Backlight Lifetime of that model is 17 000hours The Factory Calibrated Luminance cannot be achieved anymore after 4 year thus corresponding to 11 680hours Result the backlight replacement is performed under warranty Eg2 A display is used at 24 hours day ie 8 760hours year The display system is covered with a warranty program of 5 year The Guaranteed Backlight Lifetime of that model is 17 000hours The Factory Calibrated Luminance cannot be achieved anymore after 2 5years thus corresponding to 21 900hours Result the backlight replacement does not make part of the warranty coverage 1 Consumable is a part that can be replaced by the user 2 Backlight run time is the total time that an image including use of a screen saver has been applied to the screen this value can be consulted via the OSD buttons On Screen Display 3 Guaranteed Backlight Lifetime is the number of backlight hours during which a predefined luminance value ie the Factory Calibrated Luminance will be provided by a specific diagnostic display model This figure is printed on the Warranty certificate of each display or can be requested at your local Barco office 4 Factory Calibrated Luminance is the typical luminance value that a specific diagnostic displa
11. ck that all the 1 0 and power connectors are correctly and well connected as described in the Installation section Make sure the pins of the connectors are not crooked or broken Problem Partial image or incorrectly displayed image Check to see if the resolution of your computer is higher than that of the LCD Display Reconfigure the resolution of your computer to make it less than or equal to the native resolution 1920 x 1200 Problem Image has vertical flickering line bars Use Clock to make an adjustment Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD Display Problem Image is unstable and flickering 30 Use Phase to make an adjustment Problem Image is scrolling e Check and make sure the video signal cable or adapter is well connected e Check and reconfigure the display mode of the vertical refresh rate of your graphics card to make it compatible with the LCD Display Problem Vague image characters and graphics e Use Clock to make an adjustment If this problem still exists use Phase to make an adjustment Warning Signal Sometimes you may see warning messages for this LCD Display This means that the LCD Display cannot correctly receive the signal from the computer graphics card No Signal This message means that the LCD Display has been powered on but it cannot receive any signal fr
12. ct For additional copies of the Declaration of Conformity document contact Barco NV The MDRC series digital flat panel display meets the essential health and safety requirements is in conformity with and the CE marking has been applied according to the relevant EU Directives listed below using the relevant section of the following EU standards and other normative documents 37 EU EMC Directive 89 336 EEC EU Electromagnetic Compatibility Directive EN 60601 1 2 2001 Collateral standard electromagnetic Medical Electrical Equipment compatibility requirements EN 55011 Class B Limits and methods of measurements for radio interference characteristics of industrial scientific and medical equipment IEC 61000 3 2 Harmonic emissions IEC 61000 3 3 Voltage fluctuations flicker emissions IEC 61000 4 2 Electrostatic discharge requirements for industrial process measurement and control equipment IEC 61000 4 3 Radiated electromagnetic field requirements for industrial process measurement and control equipment IEC 61000 4 4 Electrically fast transients for industrial process measurement and control equipment IEC 61000 4 5 Surge requirements IEC 61000 4 11 Voltage variations dips interrupts 38 IEC 61000 4 6 Conducted immunity IEC 61000 4 8 Magnetic field immunity Conformance to the Medical Device Directive 93 42 EEC EN 60601 1 Medical Part 1 General
13. ded by Barco vi been maintained at all times in accordance with Barco s instructions or in absence thereof at least with intervals and in a manner consistent with generally accepted practice for this type of products B The warranty described herein shall not include the following 2 1 Any hardware or software item procured from a source other than Barco nv MID or their official agent or distributor and integrated by Customer or a third party into Barco nv MID supplied equipment 2 2 Any host configuration not explicitly supported by Barco nv MID 2 3 All software installed on the system whether they are acquired from Barco nv MID or third party An exception is made for software delivered by Barco nv MID that would prove to be a cause for the 42 mal functioning of the hardware covered under this Agreement 2 4 Normal wear and tear use under circumstances exceeding specifications such as use in dusty environment or under excessive temperature conditions abuse unauthorised repair or alternation lack of proper configuration or maintenance damaged or modified or removed serial number cosmetic refurbishment 2 5 Repair or replacement of consumables or specific parts that by definition are subject to wear and tear including but not limited to a CRT s LCD panels b Backlights in diagnostic LCD displays when the backlight run time is beyond the Guaranteed Backlight Lifetime of that model when used at the F
14. e available at the time of classification Because the display uses electrical energy and has no direct patient connections and by itself no medical utility the display is classified according to Rule 12 as an MDD Class device component or accessory The MDD states that manufacturers of Class medical devices or accessories shall satisfy the requirements in regard to design and manufacturing controls that is the applicable assessment route to be used for CE marking under the MDD and it shall carry the CE mark according to Annex XII of the directive with no notified body annotation In the opinion of Barco NV registration required to put this device into commerce is the responsibility of the medical device system manufacturer and Barco supports this requirement by providing a European Commission EC declaration of conformity If Barco supplies a display to an end user rather than a device manufacturer it is the end user s responsibility to ensure continued compliance with the MDD of the system in which the display is integrated The supplier will make available on request circuit diagrams component part lists etc For vigilance reporting as required under Article 10 of the MDD Barco NV will provide any information requested by competent authority to support any reported incident investigation by such an authority EU Declaration of Conformity for Medical Application A Declaration of Conformity has been filed for this produ
15. ide Not suitable for use in the presence of a flammable anesthetic mixture with air or with oxygen or nitrous oxide Mode of Operation Continuous Intended use This display is an AMLCD display designed for viewing medical X ray images This unit should not be used near patients and should be kept outside of 1 83 m perimeter and 2 29 m vertical Power connection For use only with power supply SINPRO HPU100 108 Input 100 240V 47 63Hz 1 2 0 5A Power cords Utilize a UL listed detachable power cord 3 wire type SJ or equivalent 18 AWG min rated 300 V min provided with a hospital grade type plug 5 15P configuration for 120V application or 6 15P for 240V application Do not overload wall outlets and extension cords as this may result in fire or electric shock Mains lead protection U S Power cord Power cords should be routed so that they are not likely to be walked upon or pinched by items placed upon or against them paying particular attention to cords at plugs and receptacles External equipment External equipment intended for connection to signal input output or other connectors shall comply with relevant UL EN IEC standard e g UL EN IEC 60950 for IT equipment and UL EN 60601 1 IEC 60601 series for medical electrical equipment In addition all such combinations systems shall comply with the standard IEC 60601 1 1 Safety requirements for medical electrical systems Equipment not complying with UL E
16. is compatible with the LCD screen We have listed the Compatibility Modes of this LCD screen in appendices for your reference 20 Adjusting the display position Vertical height Portrait Landscape Left to right pan Front to back tilt On Screen Display menus How to use the OSD menus 1 22 When the display is on and the OSD in not on the screen press the control wheel The front illumination is switched on for about 10 seconds To display the main menu swivel the control wheel while the illumination is on The OSD main menu appears Several menu items submenus BARG Main Menu Input Selection Adjustments Exit MDRC 2124 1920 x 1200 60H2 Note Some of the menu items described in this manual may not be available on your display depending on the se lected video input To scroll through the menu swivel the control wheel The corresponding submenus are displayed automatically The red scroll bar indicates the active menu item To jump into a submenu while it is displayed press the control wheel The red scroll bar now appears in the submenu To exit from a submenu swivel the control wheel to select Exit Next press the control wheel If you exit from the OSD main menu you exit the OSD 6 To change an adjustment value or setting swivel the control wheel to select the adjustment or setting Next press the control wheel to go into edit mode This is indicated by the trackbar tur
17. issemination of those substances in the environment and to diminish the pressure on natural resources we encourage you to use the appropriate take back systems Those systems will reuse or recycle most of the materials of your end of life equipment in a sound way The crossed out wheeled bin symbol invites you to use those systems If you need more information on the collection reuse and recycling systems please contact your local or regional waste administrator You can also contact us for more information on the environmental performances of our products Safety Instructions General Recommendations e Read the safety and operating instructions before operating the display e Retain safety and operating instructions for future reference e Adhere to all warnings on the display and in the operating instructions manual e Follow all instructions for operation and use Electrical shock To prevent the risk of fire or shock hazards do not expose this product to rain or moisture Please do not open or disassemble the product as this may cause electric shock Classification Electrical Shock Protection Class I Disconnect Device Connect Remove power cord plug directly Degree of Protection Against Electric Shock No applied part Degree of Protection Against Harmful Ingress of Water Ordinary equipment IPXO Degree of Safety in the Presence of Flammable Anesthetic Mixture with Air or with Oxygen or Nitrous Ox
18. loth with a small amount of isopropyl alcohol to remove glue or dust if the screen is still not clean Do not saturate the cloth otherwise alcohol may seep into the display case and collect in the enclosure Use a clean dry cloth to completely remove the alcohol residue e Itis advised to clean the display on weekly basis e Do not use chemically treated dust cloths acetone toluene or harsh solvents on the display case or the screen They can damage the polarizer and the display case e Do not expose the display to water or excessive moisture Do not allow water or other stains to stand on the unit Wipe liquids off immediately to prevent damage to the display case and the screen Shipping storing the display Keep the display in its shipping container until installation Return the display to its original container whenever you need to store the unit move it to another location or return it for repair The packaging supplied by the manufacturer protects the display while it is in transit See environment specifications for more information Before returning the display to the container do the following 1 Swivel the display panel in portrait mode 2 Push the panel down to the lowest position 3 Use the stand lock to anchor the panel 13 Explanation of symbols A A i DISPOSAL Do not use household or municipal waste collection services for disposal of electrical and electronic equipment EU countries require the
19. low the display to warm up to room temperature before turning it on Avoid sudden temperature changes in the environment as this may cause condensation which damages the display Do not set up the display near strong light or heat sources Do not block the vents on the back of the display or install the display in a built in enclosure Blocked vents cause excessive heat to build up inside the display increasing risk of fire When installing components turn off your computer but leave it plugged into a grounded outlet Do not remove the back cover or disassemble the display There are no user serviceable parts inside Preventing fire and injury Replace the power supply or cables if damaged Use only the power source indicated in this guide or listed on the display Do not plug the power supply into an overloaded AC outlet or extension cord Overloaded AC outlets and cords can result in electric shock or fire Do not drop or push objects into the display case Internal components contain high voltage Unplug the power cord from the wall outlet during thunderstorms Do not place magnetic devices such as motors near the display Cleaning the display Observe the following guidelines to maintain display and LCD screen e Use a clean lint free absorbent cotton cloth to clear off any residual glue from removal of the protective film or to remove surface dust Apply light pressure to remove the dust e Dampen a clean c
20. moving or deleting system files amp licensed software product files misuse circuit failure or any change damage due to fire water thunder or lightning power failure or fluctuation disruption of communication lines or due to force majeure or any reason foreign to the equipment 2 9 Any specific services or procedures asked for by Customer related to verification of repaired equipment 2 10 The evaluation cost in case of a returned product deemed functional is not covered under warranty and will be charged to the Customer at Barco s sole discretion based on a case by case evaluation ARTICLE 3 OBLIGATIONS OF THE CUSTOMER Customer hereby assumes the following obligations as partial consideration for Barco nv MID performance of its requirements under the warranty condition failure by Customer to meet its obligations under this paragraph shall excuse Barco nv MID s performance hereunder 3 1 Customer shall not expose Barco nv MID personnel to any unsafe working conditions 3 2 Repairs to equipment under warranty resulting from improper maintenance or repair performed by the Customer or its officers agents employees or representatives shall be borne by the Customer at its additional cost and expense 3 3 The Customer is responsible for installing the Barco nv MID equipment in an environment for which it was intended If there is an indication that the equipment was used even temporary outside its specifications
21. ning dashed Swivel the control wheel to change the value Press the control wheel to confirm the change For multiple choice options the currently selected option is indicated by a V OSD menus overview Input selection menu Name Auto Description Select this setting if you wish the display to select the video input automatically DisplayPort Select this setting if you wish the display to select the digital video input on the DisplayPort connector DVI Digital Select this setting if you wish the display to select the digital video input on the DVI connector DVI Analog Select this setting if you wish the display to select the analog video input on the DVI connector 23 Adjustments menu Gamma submenu 24 Name Description Luminance Allows to manually adjust the luminance target if you d experience the overall image is too dark or too bright When you change this setting the display will adjust its backlight to reach its target Gamma Jumps to the gamma submenu see below White point Jumps to the white point submenu see below Analog Jumps to the analog submenu see below This submenu is only available when the DVI analog input is selected Settings Jumps to the settings submenu see below Name Description Native If you select this gamma option the native panel gamma behavior will not be corrected DICOM Select a DICOM gamma f
22. om the computer graphics card Check all the power switches power cables and signal cables Out Of Range This message means that the signal of the computer graphics card is not compatible with the LCD Display When the signal is not included in the compatibility mode we have listed in the Appendices of this manual the LCD display will show this message 31 Product dimensions Technical specifications LCD Panel Technology TFT Color LCD E IPS Native resolution 1920x1200 Active screen diagonal 24 1 611 mm Active screen area 518 x 324 mm Pixel Pitch 0 270 x 0 270 mm Visual Characteristic Maximum luminance 400 cd m2 DICOM calibrated luminance 250 cd m2 Image stabilization BLOS Backlight sensor Contrast ratio 1000 1 typical Aspect ratio 16 10 Viewing angle CR gt 10 R L 178 typical U D 178 typical Display LUT 10 bit Response time G G 5 ms Display Functions Gamma Dicom Colors 16 8 million Connectivity and control DVI I Video Input DisplayPort USB 2 0 1 upstream 2 downstream 33 OSD languages English French German Spanish Italian Dutch Simplified Chinese Traditional Chinese Korean Japanese Options Protective Cover Yes Touch Screen Yes Landscape Portrait Yes Approvals he EN 60601 1 2 FCC B ICES 001 VCCI
23. or most medical viewing applications The DICOM gamma results in more visible grayscales in the images Description Gamma 1 8 Select one of these gamma options in case Gamma 2 2 the display replaces a CRT display with a gamma of 1 8 or 2 2 respectively SRGB Select this gamma option for viewing images intended for the internet QAWeb Select this option if you wish to use the gamma settings defined in QAWeb Agent White point submenu Name Description Native If you select this white point option the native panel white point behavior will not be corrected Clearbase A color temperature according to the clearbase film standard Bluebase A color temperature according to the bluebase film standard D65 A color temperature of 6500 Kelvin QAWeb Select this setting if you wish to use the white point settings defined in QAWeb Agent User Jumps to the user submenu see below 25 User submenu An Ge 26 Name Description Red Allows to manually adjust the image red level target Green Allows to manually adjust the image green level target Blue Allows to manually adjust the image blue level target alog submenu Name Description Auto Adjust Select this setting if you wish the display to automatically adjust the geometric and level settings of the DVI analog image Geometry Jumps to the geometry submenu see below
24. parties and hinder performance by one party of his obligations ARTICLE 8 GENERAL 8 1 Customer acknowledges its understanding that all software and electronic devices including Barco nv MID products are subject to possible error mechanical or electrical failure and should not be relied upon in inappropriate applications or without proper backup and or other safety precautions whenever personal injury or property damage may result from failure or error of the product 8 2 Barco nv MID shall not be responsible for machine failure and or its failure to render service or maintenance due to causes beyond its reasonable control 45 46 47 0120 B410640 02 November 2010 Barco nv Medical Imaging President Kennedypark 35 B 8500 Kortrijk Belgium www barco com
25. ptimal product quality Barco applies strict selection criteria for its LCD panels To learn more about LCD technology and missing pixels consult the dedicated white paper available at www barcomedical com 4 Enhance user comfort Every Barco multi head display system is color matched with the highest specification in the market Barco recommends keeping color matched displays together Furthermore it is important to use all displays of a multi head configuration at the same rate to preserve color matching throughout the economic lifetime of the system 5 Maximize Quality Assurance The MediCal QAWeb system offers online service for high grade Quality Assurance providing maximum diagnostic confidence and uptime Learn more and sign up for the free MediCal QAWeb Essential level at www barcomedical com qa Unpacking and handling tips The MDRC display is a precision instrument that requires proper care to maintain product operation and adherence to specification Unpack the display and components carefully then set up and handle the unit properly to avoid damage to the LCD panel e Use both hands to grasp the display case when lifting it from the shipping carton but avoid touching the screen Do not apply pressure to the screen or touch the screen with bare fingers or objects Pressure can affect image quality 11 Cosmetics and oils on the skin are both detrimental to the screen and difficult to remove Al
26. quirements has been tested and found to comply with the limits for Federal Communications Commission FCC Class B computing devices in a typically configured system since many medical offices are located in residential areas It is the system integrator s responsibility to test and ensure that the entire system complies with applicable electromagnetic compatibility EMC laws Barco NV has made great efforts to support the medical device industry in particular medical device manufacturers and medical device system integrators We offer state of the art color displays that are compliant with worldwide accepted medical device safety standards and for the European market CE marked displays based on compliance with counsel directive 93 42 EEC commonly referred to as the Medical Device Directive MDD The following summarizes our qualification of these displays as it relates to compliance with the MDD The European Medical Device Directive requires that the intended use of the device be defined The intended use of these displays is to display alphanumeric graphic and image data as inputted from any type of medical device These displays do not provide a measurement function in any way and it is the device and systems manufacturer s responsibility to verify its function in the integrated device or system 36 The display was classified as required by the MDD according to Annex IX of the directive and the medical device MEDDEV guidanc
27. requirements for safety Electrical Equipment U S FCC Compliance Statement This device complies with Part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful interference and 2 this device must accept any interference received including interference that may cause undesired operation Note This equipment has been tested and found to comply with the limits for a Class B digital device pursuant to Part 15 of the FCC Rules These limits are designed to provide reasonable protection against harmful interference in a residential installation This equipment generates uses and can radiate radio frequency energy and if not installed and used in accordance with the instruction may cause harmful interference to radio communications However there is no guarantee that interference will not occur a particular installation If this equipment does cause harmful interference to radio or television reception which can be determined by turning the equipment off and on the user is encouraged to try to correct the interference by one or more of the following measures e Reorient or relocate the receiving antenna e Increase the separation between the equipment and receiver 39 e Connect the equipment into an outlet a circuit different from that to which the receiver is connected e Consult the dealer or an experienced radio TV technical for help CAUTI
28. rvice centre as listed at www barcomedical com unless otherwise indicated The one way cost of packing transport and insurance related to shipping the alleged defective Product or part to Barco for repair or replacement shall be borne by Customer The one way cost of packing transport and insurance related to shipping of the repaired or replacement Product or part to Customer shall be borne by Barco 41 1 3 The Customer shall return freight prepaid the defective equipment or subassemblies in its original packaging with the assigned RMA number for repair to the Barco nv MID Customer support centre or an authorised service centre 1 4 Replacement parts used shall be new or equivalent to new parts for the revision level of the equipment A replacement LCD panel will be new or similar run time The warranty period for the replacement parts will expire at the same moment as the original warranty period of the equipment All parts replaced hereunder and returned to Barco nv MID or an authorised service centre shall become the property of Barco nv MID or the authorised service centre 1 5 The repaired equipment shall be returned to the Customer by regular freight at Barco nv MID s charge 1 6 Barco nv MID will replace a product that fails within 90 days after shipment from Barco with a new one ensuring color matching in the event of a diagnostic multi head display configuration Barco aims to ship the new replacement prod
29. tem DPMS of your display in the display s Settings menu will optimize its diagnostic lifetime by automatically switching off the backlight when the display is not used for a specified period of time By default DPMS is enabled on your display but it also needs to be activated on your workstation To do this go to Power Options Properties in the Control Panel Barco recommends setting DPMS activation after 20 minutes of non usage 2 Use a screen saver to avoid image retention Prolonged operation of an LCD with the same content on the same screen area may result in a form of image retention You can avoid or significantly reduce the occurrence of this phenomenon by using a screen saver You can activate a screen saver in the Display properties window of your workstation Barco recommends setting screen saver activation after 5 minutes of non usage A good screen saver displays moving content In case you are working with the same image or an application with Static image elements for several hours continuously so that the screen saver is not activated change the image content regularly to avoid image retention of the static elements 3 Understand pixel technology LCD displays use technology based on pixels As a normal tolerance in the manufacturing of the LCD a limited number of these pixels may remain either dark or permanently lit without affecting the diagnostic performance of the product To ensure o
30. the provisions of clause 2 repair and replacement of defects in material and or workmanship under this warranty shall be accomplished in our works according to the terms and conditions as set forth hereafter 11 Any claim under the Warranties must be notified to Barco in writing within 8 days from the date the defect or failure has been discovered or noticed the first time The Customer upon the occurrence of any equipment failure shall contact Barco nv MID customer support centre or an authorised service centre by telephone fax or e mail and shall provide the applicable customer support person with a complete description of the problem being encountered including the model and serial number of the equipment in which the problem has arisen 1 2 The customer support person shall diagnose the problem experienced by the Customer and shall advise the Customer on how to proceed Customer support may ask to return the faulty equipment or faulty subassemblies to the Barco nv or a MID customer support centre or an authorised service centre for repair activities In no event shall Customer return a defective Product or part thereof to Barco without Barco s prior written approval In the event the return to Barco of the defective Product is authorized by Barco Barco shall issue to Customer an RMA Return Material Authorization The Customer shall apply for an RMA number to the closest Barco nv MID Customer support centre or an authorised se
31. u DisplayPort input DVI I input USB upstream USB downstream DC Power input 00000 Kensington Security Slot The display can be secured to your desk or any other fixed object with Kensington lock security products Kensington lock itself is not included Installation Connecting the display Use only the power adapter power cord and the video cables shipped with this display To setup this display please refer to the following figure and procedures 1 Be sure all equipment is turned off 2 Connect the DC power cord to the power connector plug one end of the AC power cord into the power adapter and the other end into an electrical outlet 3 For a PC with DisplayPort output connect the DisplayPort signal cable from the display DisplayPort input connector to the DisplayPort connector of your host computer 4 Fora PC with DVI digital output connect the DVI signal cable from the display DVI I input connector to the DVI connector of your host computer Tighten the screws 5 Turn on your computer display and video source 19 B A LU y L Note To ensure the LCD Display will work well with your computer please configure the display mode of your graphics card to make it less than or equal to the native resolution and make sure the timing of the display mode
32. uct within 2 business days after receipt of the Customers Notification in writing ARTICLE 2 CONDITIONS PRECEDENT FOR WARRANTY AND ITEMS EXCLUDED FROM WARRANTY A The Warranties shall apply only to the extent the Products or any parts thereof have i been transported and stored at all times in the original packaging in the conditions as specified by Barco such as covered and secure location minimum and maximum temperature maximum humidity or in absence thereof at least in conditions consistent with generally accepted practice for this type of products ii been handled at all times in accordance with Barco s instructions in absence thereof at least with the care and caution consistent with generally accepted practice for this type of products iii been installed strictly in accordance with the instructions and directions given by Barco if and to the extent the Products have not been installed by Barco or its authorized subcontractors iv not been subject to any unauthorized access alteration modification or repair or attempts thereto v been at all times normally used for the intended purpose and operated in strict accordance with the operating instructions set forth in the operating manual of the Product in question and shall not have been otherwise misused abused damaged For the purpose hereof normally used shall mean a regular ordinary and routine usage of the Product in question as intended and or recommen
33. use of separate recycling collection services CAUTION Read the accompanying text carefully for proper operation and maintenance of the display system DIRECT CURRENT ALTERNATING CURRENT RELATIVE HUMIDITY Storage amp transport 5 90 No condensation Operating 8 80 TEMPERATURE Storage amp transport 20 to 60 Operating 0 35 C Introduction About the product Thank you for choosing Barco The MDRC 2124 is an LCD display with an active matrix thin film transistor TFT liquid crystal display LCD This product also demonstrates the following outstanding features e DVI I and DisplayPort signal e 24 diagonal Screen e 1920x1200 high resolution e Wide Viewing Angle Technology e 31 5 80 kHz horizontal scan e 59 61 Hz refresh rate e Auto Adjustment and Re scaling function e High quality full screen re scaling capability e Multilingual OSD user controls e VESA DPMS power saving e Kensington lock capability 15 Package overview User manual USA Power Cord EUR Power Cord China Power Cord DisplayPort Signal DVI D Signal Cable Power Adapter Cable Display parts controls and connections Front View Power LED 1 Green indicates the display is turned on 2 Orange indicates the display is in stand by mode Back View Control wheel 1 Press the control wheel for 1 sec to power off to the LCD Display 2 Swivel the control wheel for OSD men
34. y model is calibrated at during the production process This figure is printed on the Warranty certificate of each display or can be requested at your local Barco office c Lamps optical components in projectors d Replacement because of i image retention as a result of not correctly using screen saver and or Display Power Management System DPMS as explained in the user manual prolonged operation of the display with a static image on the same screen area ii anumber of missing pixels that is lower than the total allowable number as mentioned in the product specifications iii difference in color temperature that is lower than the total allowable difference as mentioned in the product specifications 43 iv difference in color temperature as a result of not using all displays of a multi head configuration at the same rate v LCD luminance uniformity that is in within the product specifications or luminance uniformity performance that is inherent to LCD technology Barco nv MID does not warrant a minimum life time nor a performance of any of the consumables 2 6 Replacement of moveable parts such as power cords remote controls 2 7 Any product disassembly and installation costs at the operation site travel expenses and travel time to and from the operation site for the personnel in charge of the repair works and transport charges 2 8 Any failures resulting from an accident negligence such as but not limited to re
Download Pdf Manuals
Related Search