APart SDQ5PIR-BL loudspeaker
Contents
1. and the amplifier is not ready it will answer STANDBY ON Please wait until the speaker is operational green led at the back is lit and resend the instruction WWW APART AUDIO COM CD EE RS232 COMMANDS SDQLVL Volume level GET SET INC OFF 64 DEC 63 to 0 MAXLVL Maximum GET SET BACK OFF 64 BACK allowed level 63 to 0 BALANCE Left right GET SET balance RS232line feed GET SET RS232 GET SET backspace VALFB RS232 value GET SET feedback BACKCT Back panel GET SET control WALLCT Wall panel GET SET control IRRMCT Infrared remote GET SET control AUTOPW Auto power off GET SET AUPTRG Auto power GET SET trigger level settings GET information HWVRSN Hardware GET version ET A B WI at 0 AB at 2 NA NA SWVRSN NA RESTORE Restore factory S defaults INFO APART AUDIO COM CD EE ir Remote Control The included infrared remote control unit is powered by a standard CR2025 3V lithium battery Before first use carefully remove the transparent battery saver When the battery is empty replace with the same type only Slide out the battery holder from the remote control unit remove the empty battery and put a fresh one in place The battery holder has a mark on it Make sure you insert the battery and holder in the right way Eye receiver If you don t use the remote for an extended period of time remove the battery and store it in a safe location This will a2. due to transport and rough handling is not covered by the manufacturers warranty The SDQ5Pir complies with CE regulations WWW APART AUDIO COM CD EE Rear panel 1 Power switch turn mains E power on and off AP 2 Power cord inlet attach the power cord supplied to this H socket The inlet also contains REMOTE CONTROL POSSUBLEVIA the mains fuse A CE 3 Multifunction led this led is orange in standby mode green pe when the speaker is active Annana oj and red when an overload or E clipping occurs 4 Treble control push the OFF Nemo or button once to increase or d decrease the treble tone control in steps of 2 dB Push both and buttons simultaneously to reset the tone control to neutral position 5 Bass control push the or button once to increase or decrease the bass tone control in steps of 2 dB Push both and buttons simultaneously to reset the tone control to neutral position 6 Master volume control this volume control sets the level of the SDQ5Pir speaker 7 Wall panel connector standard RJ45 connector for connection of an optional wall control panel This connection is NOT COMPATIBLE with other networks such as computer networks etc Do not attempt to connect anything else but the optional SDQ5Pir wall control panels 230VAC BOVATM AX F USE F 1A WALL PANEL 8 Right speaker out
3. APart SDQ5Pir ouam Ae a g SDQ5Pir INFO APART AUDIO COM CD EE Features The APart SDQ5Pir powered loudspeaker set is a versatile and very compact easy to use plug and play sound system It consists of an amplified loudspeaker with a 5 25 woofer a high frequency unit and a second linkable passive loudspeaker powered by the second amplifier built into the active speaker The speakers are magnetically shielded The speakers can be remote controlled via the included infrared remote control RS232 serial port or an optional wall control panel with or without local input The auto power off function switches off the power amplifier when no audio signal is present for a certain time This time window can be adjusted using RS232 commands Further benefits are presettable maximum level dual inputs unbalanced on minijack and balanced on euroblock additional input via optional wall control unit All inputs can be gain adjusted used individually or mixed together except optional wall control panel local input source this input can not be mixed with the A or B or A B inputs The automatic power on function will power up the speaker automatically from the standby position when a sufficiently strong audio signal is present The threshold can be adjusted via RS232 control to suit your needs Active 2 way bass reflex speaker system Ideal for monitor Audio Video applications multimedia applications Pow
4. ART AUDIO COM
5. Y OFF After that resend the command and it will be executed An instruction has at least a command and an attribute many cases there are extra values needed like a source lettre or a value From here we assume that you are familiar with RS232 communication protocols and connections If not please read the user manual of your control device first Instructions always have to be ended with CR carriage return Line feed lt LF gt characters will always be omitted however SDQ5Pir can use and echo lt LF gt after a CR Instructions are not case sensitive The 4 possible commands are SET GET INC and DEC With the INC and DEC command a step value can be specified See the table below for details in the value column Operating Settings SDQLVL is the volume level of the speaker system Possible values are OFF mute or any value between 63 lowest and 0 highest volume level E g you want to set the volume to 20 SET SDQLVL 20 CR The unit will reply SDQLVL 20 MAXLVL is the maximum allowed volume level E g if you don t want anyone to set the SDQ level higher than 10 set the MAXLVL parameter to 10 All volume related commands will ALWAYS be related to the MAXLVL setting E g if the MAXLVL is 10 and you enter the command SET SDQLVL 20 the SDQ5Pir will set the level relative to the MAXLVL which was 10 Please note that the absolute maximum number of volume steps is limited to 64 steps 1 volume step co
6. choed back This can be handy when programs like hyperterminal are used LF is Line Feed Line Feed is an ASCII character which is sometimes used to let the cursor jump to the next line SDQ5Pir always omits the line feed character However when LF is on there will be put lt LF gt character behind each CR character This is both the case for echoing as for messages sent by SDQBSPir Please take a look to following example in both cases the user sends the following string get sdqlvl lt CR gt With ECHO on and LF off this will be returned by SDQ5Pir get sdqivi lt CR gt command SDQLVL 16 lt CR gt reply In case both ECHO and LF are on it will be like this get sdglvi CR LF SDQLVL 16 lt CR gt lt LF gt BS is Back Space This is also an ASCII character In case BS and ECHO is on SDQ5Pir will reply lt 5 gt lt 5 gt lt 5 gt each time when a BS is received SP is the space character This setting is only intended to have a nice text when used with programs like Hyperterminal VALFB means value feedback Possible values are on or off When value feedback in on the SDQSPir will reply its setting after a value has been changed such as SDQLVL Version information HWVRSN will return the hardware version number GET HWVRSN lt CR gt SWVRSN will return the hardware version number GET SWVRSN CR Control settings set the controls at the back of the unit on o
7. erfull HiFi 5 25 woofer and 1 tweeter Mounting brackets IR remote control and power cord included e 2 x 30 watts RMS output power 200 Watts PMPO dynamic e Enhanced bass response by DTB reflex tuning Multifunction led indicator standby orange on green overload red off led not lit Hi Q balanced inputs Stereo inputs on standard 3 2 mm mini stereo jack compatible with headphone outputs and line inputs Computer MP3 players Input sources A B or via optional wall panel Inputs A and B can be mixed together or selected individually by infrared remote control or RS232 Magnetically shielded e Stylish design suited for placement in corners Very high efficiency high output e Standby mode for low power consumption Controllable via infrared remote included RS232 wall panels optional e RS232 control for increased integration in automated audio systems using standard 9 pin serial cable RJ45 remote wall panel connector not compatible with computer networks or other types of remote control cabling These speakers have been carefully packed at the factory Open the carton box and remove the speakers from the packing Do not use sharp objects Place the speakers on a flat surface The mounting brackets infrared remote control unit power cord and speaker interconnection wire are included in the packing When the product shows signs of damage caused by transportation contact your dealer immediately Damage
8. n good condition Should you ever need to ship the unit use only the original factory packing Do not spill water or other liquids into or on the unit Make sure power outlets conform to the power requirements listed on the back of the unit Do not use the unit if the electrical power cord is frayed or broken Always operate the unit with the AC ground wire connected to the electrical system ground Have gain controls on amplifiers turned down during power up to prevent speaker damage if there are high signal levels at the inputs Do not connect the inputs outputs of amplifiers or consoles to any other voltage source such as a battery mains source or power supply regardless of whether the amplifier or console is turned on or off Power down amp disconnect units from mains voltage before making connections Do not use the unit near stoves heat registers radiators or other heat producing devices Do not remove the cover Removing the cover will expose you to potentially dangerous voltages Do not drive the inputs with a signal level higher than that required to drive equipment to full output In case of mal function this device should be serviced by qualified service personnel only INFO APART AUDIO COM GDam EE Company names product names and names of formats etc are the trademarks or registered trademarks of their respective owners 2009 APart Audio specifications subject to change without notice WWW AP
9. put output to the passive slave loudspeaker right channel on euroblock Connect the Right LS out to the euroblock connector of the slave unit passive speaker 9 Balanced input input B right channel balanced input on euroblock 10 Balanced input input B left channel balanced input on euroblock 11 Mono stereo selector switch to stereo for normal operation For mono operation switch to upper position In this case the left input signal only is used on both channels 12 Input A minijack standard 3 2 mm stereo minijack connector for input A 13 RS232 connector standard SUB D9 connector for serial control 14 Heatsink INFOCAPART AUDIO COM CD EE RS232 communication Communication with SDQ5Pir via RS232 is done with simple ASCII Commands and Replies The port settings are 19200 Baudrate 8 databits no parity and 1 stop bit The physical connection is as described below Standard 9 pin serial cable wired straight through no null modem cable Maximum wire length depends on cable quality and influence from external interference Pin 2 TX data data transmission output Pin 3 RX data data reception input Pin 5 GND ground Other pins are not used NOTE when the unit is in standby mode it may not respond to the first command sent to the unit unless you send the command SET STANDBY OFP If you want to send any other command while the unit is in standby mode it will wake up from standby and reply STANDB
10. r off NOTE when set to off you can NOT operate the unit from the back panel controls WALLCT set the control of the optional wall control panel on or off IRRMCT set the control by infrared remote on or off AUTOPW set the time for the auto power off function When no audio signals are detected the speaker will go to standby mode after the AUTOPW time has elapsed When set to 0 the AUTOPW function in not active Values between 0 and 30 can be specified 0 inactive 1 auto power off after 1 minute etc Default value is 15 minutes INFO APART AUDIO COM CD EE Restore Factory Settings The factory defaults are shown in the 5232 commands table In order to restore the factory default settings enter the following command SET RESTORE ON lt CR gt This function can also be executed without using RS232 commands In that case power off the speaker While pushing BASS and buttons on the rear panel simultaneously power up the speaker with the power switch The multifunction led will be orange Release the BASS and buttons one second after powering up All factory defaults will be restored Standby The SDQ5Pir can be switched to Standby mode with the IR remote control or with the SET STANDBY lt gt instruction Leaving Standby mode can also be done with IR remote controller or the SET STANDBY OFF CR instruction If an RS232 instruction is sent when the amplifier is in Standby mode or during power on
11. rresponds to 1 25 dB The MAXLVL parameter is therefore considered as the master volume If you want to mute the speaker you can set the MAXLVL parameter to OFF BALANCE sets the balance between left and right channel Possible values vary between 31 and 31 Equalizer EQBASS sets the level of the bass EQTREB sets the level of the treble The value must be between 14 and 14 in steps of 2 If a different value is used e g 5 it will be changed to the closest match WWW APART AUDIO COM CD EE Configuration Settings SELECT is input source selection a possible command could look like this Set select AB lt CR gt In this case both inputs and B will be mixed together by the SDQ5Pir unit Possible values are A B AB WI WI is the local input of the optional waal control IPGAIN is input gain Each source input has its own gain setting so the source A B or WI needs to be specified The value can be between 0 and 3 in steps of 1 If an invalid value is used or no source is specified ERROR Value Invalid lt CR gt will be replied Otherwise the reply will be Command Executed CR A command to set the input gain of source A to 1 looks like this SET IPGAIN A 1 lt CR gt AUPTRG auto power trigger level Range from O to 30 Higher values will increase the trigger level RS 232 Settings All RS 232 settings are binary values they can be ON or OFF If ECHO is on all received characters are e
12. void possible damage or corrosion from battery leakage Warning Do not attempt to recharge disassemble or incinerate this type of battery Keep all batteries away from children Dispose of used batteries promptly and as regulated by applicable laws WWW APART AUDIO COM CD EE ir Commands Pare ue TREBLE TREBLE SDQ5Pir SPEAKER SYSTEM SDQ5Pir SPEAKER SYSTEM SDQSPir LR REMOTE CONTROL LR REMOTE CONTROL I MOTE CONTROL Function 9 me 9 SDQ5Pir device code is 807F TrebleUP 0D Infrared commands have been coded according to the protocol INFO APART AUDIO COM EE Technical specifications Speaker type Input impedance minijack input A Input sensitivity minijack input A Input impedance balanced input B Input sensitivity balanced input B Tone control treble Frequency range Dimensions h x w x d mm Net weight 2 85 kg active 1 75 kg slave control unit connection wire Remote control unit battery type WWW APART AUDIO COM CD EE ortant safety instructions Please check the carton box for any kind of damage on reception of the goods In case of a damaged carton please contact your dealer before opening the carton Read all documentation before operating your equipment Keep all documentation for future reference Save the carton and packing material even if the equipment has arrived i
Download Pdf Manuals
Related Search