Miele DA 489-4 Ext
Contents
1. Cleaning and care m To remove the side vapour plates hold on the side pull out of the holder at the bottom 1 then slide towards the middle and pull downwards 2 m See the notes under Housing for how to clean the vapour plates dai2107 m Pull the grease filter by the hand hold forwards and out Cleaning the grease filter by hand m Clean the filter with a soft nylon brush in a mild solution of hot water and a small amount of washing up liquid Do not use undiluted washing up liquid Do not use cleaning agents containing descaling agents powder cleaners cream cleaners or abrasive all purpose cleaning agents oven sprays Cleaning the grease filter in the dishwasher m Place the filter with the short side upright in the lower basket and wash in a 65 programme using a mild dishwasher detergent ensuring the spray arm is not obstructed Depending on the cleaning agent used cleaning the grease filter in a dishwasher can cause permanent discolouration to the surface However this will not affect the functioning of the filter in any way m After cleaning leave the filter to dry for a while on an absorbent surface before putting it back in place 23 Cleaning and care When removing the filter for cleaning also clean off any residues of oil or fat from the now accessible housing to prevent the risk2. 330 m3 h Level IV Intensive Setting 490 m3 h Special accessory for recirculation mode Conversion kit DUW 20 Miele charcoal filter DKF 12 1 For EXT models the connected load and extraction power will depend on the type of external motor fitted EXT models Length of connection cable to external MOL o ic keen Ree Res 1 9m 39 United Kingdom Miele Co Ltd Fairacres Marcham Road Abingdon Oxon OX14 1TW Tel 01235 554455 Fax 01235 554477 Customer Contact Centre Tel 08707 554466 E mail info miele co uk Internet www miele co uk Australia Miele Australia Pty Ltd ABN 96 005 635 398 1 Gilbert Park Drive Knoxfield VIC 3180 Tel 03 9764 7130 Fax 03 9764 7149 Internet www miele com au China Miele Shanghai Suite 4105 06 Plaza 66 1266 Nanjing Road West Jing An District Shanghai 200040 PRC Tel 86 21 6288 4200 Fax 86 21 6288 4100 E mail mieleshanghai cn miele com Internet www miele cn Hong Kong Miele Hong Kong Limited AIA Plaza 24 Floor 18 Hysan Avenue Causeway Bay Tel 852 2610 1331 Fax 852 2610 1013 E mail mielehk miele com hk nternet www miele hk Ireland lele Ireland Ltd Broomhill Road Tallaght Dublin 24 Tel 01 461 0710 Fax 01 461 07 97 E Mail info miele ie nternet www miele ie New Zealand Miele New Zealand Limited Unit L 10 20 Sylvia Park Road Mt Wellington 1060 Auckland NZ
3. Overheated oil and fat can ignite and could set the cooker hood on fire P Do not use the cooker hood without the filters in place This way you will avoid the risk of grease and dirt getting into the appliance and hindering its smooth operation P gt The filters should be regularly cleaned or changed as appropriate Saturated filters are a fire hazard See Cleaning and care P Do not use a steam cleaner to clean this appliance Steam could reach the electrical components and cause a short circuit Correct installation P gt Refer to the cooker or hob manufacturer s instructions as to whether a cooker hood may be operated above the cooker hob P gt The minimum safety distances between the top of the cooker or hob and the bottom of the cooker hood given in the Appliance dimensions section of this booklet must be maintained unless the hob manufacturer states that a greater safety distance is required If more than one cooking appliance is fitted beneath the cooker hood and they have different minimum safety distances to the cooker hood select the greater distance Warning and Safety instructions gt gt Safety regulations prohibit the fitting of a cooker hood over solid fuel stoves gt All ducting pipework and fittings must be of non flammable material These can be obtained from the Miele Spare Parts department or from builders merchants gt The appliance must not be connected to a chimney or
4. All the indicator lamps will go out If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the original setting Operation To activate and alter the charcoal m Use the controls to select the filter operating hours counter desired time in recirculation mode The charcoal filter is needed for recirculation mode On delivery the operating hours counter Apa m Confirm the selection by pressing the for the charcoal filter is deactivated charcoal filter control For recirculation mode the operating hours counter needs to be set to suit the type of cooking you do All the indicator lamps will go out If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the original setting m Press the On Off control to switch the fan off 5115 Y amp gt m Press the run on option and the charcoal filter controls at the same time The indicator lamp for the charcoal filter control and one of the lamps above the controls will flash S M The control lamps show the time which has been set tst lamp from the left 120 hours 2nd lamp from the left 180 hours 3rd lamp from the left 240 hours Ath lamp from the left deactivated Operation Resetting the charcoal filter operating hours counter The indicator lamp for the charcoal filter control will light up after the cooker hoo
5. Tel 0800 264 353 Fax 0800 463 453 Internet www miele co nz South Africa Miele Pty Ltd 63 Peter Place Bryanston 2194 P O Box 69434 Bryanston 2021 Tel 27 0 11 548 1900 Fax 27 0 11 548 1935 E mail info miele co za Internet www miele co za Singapore Miele Southeast Asia Miele Pte Ltd 163 Penang Road 04 02 03 Winsland House ll Singapore 238463 Tel 65 6735 1191 Fax 65 6735 1161 E Mail infosea miele com sg Internet www miele sg United Arab Emirates Miele Appliances Ltd P O Box 11 47 82 Gold amp Diamond Park Sheikh Zayed Road Building 6 Offices Nos 6 214 to 6 220 Dubai Tel 971 4 341 84 44 Fax 971 4 341 88 52 E Mail info miele ae Internet www miele ae Alteration rights reserved 1209 CE M Nr 07 286 900 02
6. The cooker hood should be installed according to local building regulations Seek approval from the building inspector where necessary All ducting pipework and fittings must be of non flammable materials The exhaust ducting should be as short and straight as possible To ensure efficient air extraction the diameter of the exhaust ducting should not be less than 150 mm If exhaust ducting with a diameter of less than 150 mm or if flat ducting is used the noise level of the cooker hood will increase and extraction will be less efficient Only reduce the diameter of the ducting if absolutely necessary e g where narrower ducting has already been installed Only use wide radius bends Tight bends reduce the air throughput of the cooker hood Only use smooth pipes or flexible hoses made from non flammable materials for extraction connection If the exhaust ducting is secured to the exhaust stub by a hose clip ensure that it is fitted correctly Do not overtighten Otherwise the exhaust stub could buckle and the non return flap could become jammed Where ducting is horizontal it must be laid to slope away at at least 1 cm per metre This is to ensure that condensate cannot drain back into the cooker hood If the exhaust air is to be ducted into the open air the installation of a telescopic wall vent is recommended o S 2 isi ki HHH lf the exhaust air is to be duct
7. a 1 lever for dismantling the tower 31 Installation Before installation it is important to read the information given on the following pages as well as the Appliance dimensions and the Warning and Safety instructions at the beginning of this book This is particularly crucial when using the cooker hood at the same time as a heating appliance that relies on air from the same room as this could result in the build up of toxic fumes Installation instructions See enclosed Installation sheet for instructions on how to install this appliance Protective foil on stainless steel appliances Some of the housing components have protective foil around them to prevent them being damaged during transport m Please remove this foil before fitting the housing components It can be peeled off easily 32 Dismantling Should the appliance ever need to be dismantled follow the installation instructions in reverse order as described on the installation sheet A lever is supplied to assist with the removal of the tower dai0920 m Push the lever between the tower and the extension piece to lever the tower out of its fixings Connection for air extraction Important To avoid the danger of toxic fumes please observe the Warning and Safety instructions This is especially crucial when using the cooker hood at the same time as another heating appliance which relies on air from the same room
8. vent flue which is in use Neither should it be connected to ducting which ventilates rooms with fireplaces gt If exhaust air is to be extracted into a chimney or ventilation duct no longer used for other purposes seek professional advice Accessories gt Only use genuine Miele spare parts and accessories with this appliance If spare parts or accessories from other manufacturers are used this will invalidate the guarantee and Miele cannot accept liability The manufacturer cannot be held liable for damage caused by non compliance with these Warning and Safety instructions Guide to the appliance ae Wami zama mai ma Ce o of ecoe aa T o G 2 Guide to the appliance Telescopic extension piece 2 Recirculation grille only for recirculation mode 3 Tower Canopy Control panel Hob lighting Grease filter Charcoal filter special accessory for recirculation mode Vapour plates 49 Touch control for hob lighting This control switches the lighting on and off and is also a dimmer switch 4 On Off touch control for the fan 423 Touch controls to select fan power level 43 Touch control for the run on option To activate the run on option The fan can be set to continue running and to switch off automatically after either 5 or 15 minutes 42 Touch control for the grease filter The indicator lamp for
9. Green yellow earth Blue neutral Brown live WARNING THIS APPLIANCE MUST BE EARTHED 35 Operation with DSM 400 control module The Miele DSM 400 control module can be used to combine the cooker hood with other components It enables the following Connection to a window contact switch If adequate ventilation to the room can only be ensured by having a window open when the cooker hood is in use at the same time as a heating appliance which depends on the air from the same room then the control module can be used to connect a window contact switch not supplied to the appliance Once connnected the cooker hood can only be operated when the window is sufficiently open see also Warning and Safety instructions When the window is closed the cooker hood fan cannot be switched on The indicator lamp for the On Off touch control on the cooker hood will flash The same applies to operation with an external motor depending on model The cooker hood lighting is not affected by this EXT models can also be connected to a window contact switch Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain 36 If the control module is disconnected in order to operate the cooker hood without the window contact switch e g after moving house the cooker hood electronics must be reset by a Miele service technician Potential free connect
10. Miele Operating and installation instructions Cooker hood DA 489 4 DA 489 4 EXT To avoid the risk of accidents en GB AU NZ or damage to this appliance it is essential to read these instructions before it is installed and used for the first time M Nr 07 286 900 Contents Caringfortheenvironment 3 Warning and Safety instructions 4 Guide to the appliance 10 Modesofoperation 12 Mieledehome 13 AA IY oreas aep EAEE Ale Byler USEA CES ALALA KUNUNUA WE 13 Operation AAA LR Pee ROE Cee DOs 14 TOSWITGHANG TAN OM EIA oy ata E ews Oe Be S 14 Toselecta power level joa ea 2 cciet ee any whats Boe wena dee Oe eet 14 INTENSIVE soting IAA KIWA 14 AI ya yA AA Ta AAA AA AAA Gerke Oia ee AAA 15 TOSWitch thetaMm AA anak ei we II Ee ee a ee 15 To switch the hob lighting on IIIA 16 Te dinyvithe hob liGhting III UHAI 16 To switch the hob lightingoff 16 Filter operating hours counter IAA 17 Cleaning and care 21 PIOQUSING IA II WA WA IIIA 21 General NOES sacia eat aaa a a AN dedanesd eae awe e tae 21 Important for appliances with stainless steel housing 21 Vapour plates and grease
11. be mounted flush with the ceiling make sure there is adequate space below it for working See maximum minimum appliance height 29 Installation Assembly parts Installation 3 protective sheets for use when fitting the tower 2 2 hose clips for securing the exhaust ducting 3 1 reducing collar for exhaust ducting 2 125 mm 1 non return flap for fitting into the exhaust connection on the motor unit not needed for recirculation mode Telescopic wall bracket for securing the cooker hood to the wall Damper to protect the glass canopy when it is tilted up and down Conversion kit for recirculation mode including directional unit and flexible aluminium hose the conversion kit is not supplied with the cooker hood but is available as an optional extra See Technical data Installation instructions Q m gt 8 large headed screws 5 x 40 mm and 8 x S 8 plugs for securing the retaining plates and the appliance unit The screws and plugs are designed for use in solid walls For other types of wall construction alternative fixings will be required Make sure the wall is strong enough to bear the weight of the cooker hood 2 x M6 self tapping nuts for securing the appliance k 8 screws M 4 x 16 mm for securing the canopy and the filter housing ISS 1 hexagonal Allen key for adjusting the height of the appliance
12. d has operated for the number of hours set The charcoal filter must then be replaced with a new one see Cleaning and care Afterwards the charcoal filter operating hours counter must be reset oO m Press and hold the charcoal filter control for about 3 seconds while the fan is switched on The indicator lamp for the control will go out 20 Reading the charcoal filter operating hours counter To check the percentage of time set already used o m Press the On Off control to switch the fan on m Press and hold the charcoal filter control S M O E One or more of the indicator lamps for the controls will flash The number of flashing lamps shows the percentage of the operating time which has already been used up ilamp 25 2lamps 50 3lamps 75 4lamps 100 The number of operating hours used remains in the memory even when the appliance is switched off or there is a power cut Cleaning and care Before carrying out any cleaning or maintenance work disconnect the cooker hood from the mains supply Ensure that itis switched off at the isolator or at the wall socket and the plug removed or the fuse is withdrawn from the fused spur connection unit or the mains fuse is withdrawn or the screw out fuse is removed in countries where this is applicable A range of Miele branded cleaning and conditioning agents are available to order
13. e mains supply make sure that the voltage and frequency details given on the data plate correspond with the on site electricity supply otherwise the appliance could be damaged Consult a qualified electrician if in any doubt gt gt The electrical safety of this appliance can only be guaranteed when continuity is complete between it and an effective earthing system which complies with current local and national safety regulations It is most important that this basic safety requirement is present and tested regularly and where there is any doubt the household wiring system should be inspected by a qualified electrician The manufacturer cannot be held liable for the consequences of an inadequate earthing system e g electric shock P gt For safety reasons this appliance may only be used when it has been fully installed gt Only open the housing as described in the instructions given in the installation sheet and in the Cleaning and care section of this booklet Under no circumstances should any other parts of the housing be opened Tampering with electrical connections or components and mechanical parts is highly dangerous to the user and can cause operational faults gt gt Installation maintenance and repairs may only be carried out by a Miele authorised person in accordance with current national and local safety regulations Repairs and other work by unqualified persons could be dangerous The manufacturer ca
14. ed into a vent flue the ducting must be directed in the flow direction of the flue 33 Connection for air extraction Important Cooker hoods designed for use with an external motor EXT models have an If the exhaust ducting is to run through integrated condensate trap rooms ceiling space etc where there may be great variations in temperature between the different areas the Silencer problem of condensation will need to optional accessory for EXT models be addressed The exhaust ducting only will need to be suitably insulated Condensate trap optional accessory dai2003 To achieve even further reductions in noise levels EXT models can have a special silencer fitted in the ducting system It can be sited at any suitable position SH in the ducting system between the sss cooker hood and the external motor In addition to insulating the exhaust ducting we recommend that a suitable condensate trap is installed to collect and evaporate any condensate which may occur Condensate traps are available for 125 mm or 2 150 mm ducting When installing a condensate trap ensure that it is positioned vertically and if possible directly above the exhaust connection The arrow on the housing indicates the direction of air flow 34 Electrical connection All electrical work should be undertaken by a suitably gualified and competent person in strict accordance wit
15. en it is switched on The Miele DSM 400 control module offers the possibility of combining other components with the cooker hood see Operation with Control module DSM 400 It is available to purchase as an optional extra If in any doubt the advice of a qualified builder gas fitter Corgi registered in the UK or electrician must be sought If the hood is being operated in recirculation mode the above restrictions do not apply Warning and Safety instructions Correct use gt Never use an open flame beneath the cooker hood To avoid the danger of fire do not flamb or grill over an open flame When switched on the cooker hood could draw flames into the filter Fat particles drawn into the cooker hood present a fire hazard P When using the cooker hood over a gas hob ensure that any burners in use are always covered by a pan Switch the cooking zone off when a pan is removed even for a short time Regulate the flame so that it does not burn up the sides of the pan Do not allow the pans to overheat excessively e g when using a wok The cooker hood can become damaged when exposed to excessive heat PD Always switch the cooker hood on when a cooking zone is in use otherwise condensation may collect in the hood which could cause corrosion P gt When cooking with oil or fat chip pans and deep fat fryers etc do not leave the pans unattended Never leave an open grill unattended when grilling
16. f or if the appliance is under guarantee please contact your Miele Dealer or the Miele Service Department see back cover for contact details When contacting the Service Department please quote the model and serial number of your appliance These are shown on the data plate which is visible when the vapour plates are removed For GB Please note that telephone calls may be monitored and recorded for training purposes 38 Technical data Total connected load 280 W Fan motor 200 W Hob lighting 4x 20W VONAGE IA AC 230 V FICQUCNGY nis banat ood aoe ss 50 Hz Fuse rating GB 13A AUS NZ Plug rating esr rcir eee taaa 10A Test marks Electrical safety ee ee AREA C Tick Mark Electrically suppressed according to AS NZS 1044 Weight DA 489 4 34 5 kg DA 489 4 EXT 31 5 kg Fan performance Extraction power according to EN 61591 Extraction system 2 150 mm Level ck cs cece ae oo ee 200 m h LOVEW Wicca ep carsind Sean 300 m3 h Level Il 400 m3 h Level IV Intensive Setting 640 m3 h Extraction system 2 125 mm KUA te Seen eee 180 m3 h OVEN Wiest cen tae aes ee esate 280 m3 h Level WI 380 m3 h Level IV Intensive Setting 580 m3 h Unrestricted 690 m3 h Recirculation with charcoal filter Levell 150 m3 h Levelli EE 210 m h Level Il
17. f the cooker hood is connected for recirculation a charcoal filter must be inserted in addition to the grease filter This is designed to absorb cooking odours It is fitted in the canopy above the grease filter New filters can be purchased from your Miele Dealer Chartered Agent or from the Miele Spare Parts Department See back cover for contact details and Technical data for the model number of the filter m Before fitting or replacing the charcoal filter the vapour plates and the grease filter must first be taken out See previous section for instructions on how to do this m Take the charcoal filter out of its packaging EEE dai2108 m Slide it in above the guides for the grease filter m Replace the grease filter and vapour plates 25 Cleaning and care When fitting for the first time m Activate the operating hours counter see Operation Always replace the charcoal filter im mediately if the indicator lamp for the charcoal filter lights up or if itis no longer effective in absorbing kitchen odours It should however be replaced at least every 6 months Used charcoal filters can be disposed of with the normal household waste m After fitting the new charcoal filter press the charcoal filter touch control for approximately 3 seconds to reset the operating hours counter The charcoal filter indicator lamp will go out m f the charcoa
18. filter 22 GlaSS SUNACES aii piani ate EA eed doles ER Hobe ew E 25 Fitting and replacing the charcoal filter 25 Changing the halogen lamps 27 Appliance dimensions 28 Safety distance between hob and cooker hood S 29 Installation 22 eee 30 Connection for air extraction 33 Condensate trap 34 SUN IA AAA Ia 34 Electrical connection 35 Operation with DSM 400 control moduee 36 Connection to a window contact switch 36 Potential free connection 36 Connectiontoalightswitch 37 After sales service 38 Technical data II ds bes se heeds ea Ree bernie Bent 39 2 Caring for the environment Disposal of the packing material The transport and protective packing has been selected from materials which are environmentally friendly for disposal and can normally be recycled Packaging e g cling film polystyrene and plastic wrappings must be kept out of the reach of babies and young children Danger of suffocation Dispose of or recycle all packa
19. ging materials safely as soon as possible Disposal of your old appliance Electrical and electronic appliances often contain materials which if handled or disposed of incorrectly could be potentially hazardous to human health and to the environment They are however essential for the correct functioning of your appliance Please do not therefore dispose of it with your household waste Please dispose of it at your local community waste collection recycling centre or contact your dealer for advice Ensure that it presents no danger to children while being stored for disposal It should be unplugged or disconnected from the mains electricity supply by a competent person Warning and Safety instructions This appliance complies with all relevant local and national safety reguirements Inappropriate use can however lead to personal injury and damage to property To avoid the risk of accidents and damage to the appliance please read these instructions carefully before using it for the first time They contain important information on the safety installation use and maintenance of the appliance Keep these instructions in a safe place and ensure that all users are familiar with the contents Pass them on to any future owner of the appliance Correct application P gt This appliance is intended for domestic use only Any other usage is at the owner s risk and could be dangerous The manufacturer cannot be
20. h national and local safety regulations BS 7671 in the UK Installation repairs and other work by unqualified persons could be dangerous for which the manufacturer cannot be held liable Ensure power is not supplied to the appliance until after installation or repair work has been carried out Do not connect the appliance to the mains electricity supply by an extension lead These do not guarantee the required safety of the appliance The voltage and connected load are given on the data plate This is visible when the vapour plates are removed Ensure that these match the household mains supply Connection of this appliance should be made via a suitable isolator or a double pole fused spur connection unit which complies with national and local safety regulations and the On Off switch should be easily accessible after the appliance has been built in When switched off there must be an all pole contact gap of 3 mm in the switch including switch fuses and relays according to EN 60 335 If the switch is not accessible after installation depending on country an additional means of disconnection must be provided for all poles For extra safety it is advisable to install a residual current device RCD with a trip current of 30 mA Important This appliance is supplied for connection to an a c 230 V single phase 50 Hz supply The wires in the mains lead are coloured in accordance with the following code
21. have side reflectors The halogen lamp must be positioned with the reflector at the top so that the light is directed downwards m Refit the lamp cover using the two screws 27 Appliance dimensions 1 Extraction 2 Recirculation 3 Ventilation grille positioned at the top for recirculation 28 ka uo ee ge 4 and 5 5 is not required for recirculation mode cooker hoods The shaded area represents the wall or ceiling area for the vent cut out for fitting the connection socket and on EXT models for feeding the connection cable through to the external motor For recirculation mode only a connection socket needs to be fitted Connection for air extraction 150 mm or 125 mm with reducing collar Appliance dimensions Safety distance between hob and cooker hood S The safety distance between the top of a cooker or hob and the bottom of the cooker hood glass canopy must measure at least 350 mm unless a greater distance is specified by the manufacturer of your cooking appliance See Warning and Safety instructions Account should also be taken of the height of the person who will be using the hood most often The person should have sufficient space to work comfortably at the hob and also be able to reach the hood controls with ease If positioned too high extraction will be inefficient If you want the top of the cooker hood to
22. held liable for damage resulting from incorrect or improper use or operation P gt This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience or knowledge unless they are supervised whilst using it or have been shown how to use it correctly by a person responsible for their safety Safety with children gt This appliance is only intended for use by adults who have read these instructions gt This appliance is not a toy To avoid the risk of injury keep children well away and do not allow them to play with it or to use the controls They will not understand the potential dangers posed by it They should be supervised whenever you are working in the kitchen P Older children may use the cooker hood only when its operation has been clearly explained to them and they are able to use it safely recognising the dangers of misuse PD Please be aware that on cooker hoods with halogen lighting the lamps will get very hot during use and remain hot for some time after switching off To safeguard against burning keep children well away from the lamps at all times Warning and Safety instructions Technical safety gt gt Before installation check the cooker hood for visible signs of damage Under no circumstances should you use a damaged appliance A damaged appliance is dangerous gt gt Before connecting the appliance to th
23. ion This enables a further appliance to be controlled by the switch setting on the cooker hood fan For instance it can be used to ensure a sufficient supply of fresh air when the cooker hood and a heating appliance which also depends on the air in the room are being used together by switching on an air intake fan or opening a motorised inlet flap as soon as the cooker hood fan is switched on It is important to ensure that the fan power is sufficient and that the air intake has a suitable cross sectional diameter Ifa sufficient air intake cannot be guaranteed then the potential free contact will enable a heating appliance which depends on air in the same room as a cooker hood to be switched off when the cooker hood is in operation See also Warning and Safety instructions Operation with DSM 400 control module Connection to a light switch The control module can be used to switch on the cooker hood lighting and also to dim it via a light switch in the house Installation dai1874 The tower needs to be removed before the control module can be fitted to the fan unit A fixing bracket is required for fitting the control module This is available as an optional accessory M Nr 8363350 The control module is supplied with its own detailed operating and installation instructions 37 After sales service In the event of a fault which you cannot correct yoursel
24. l green indicator lamps are usually sufficient for normal cooking Intensive setting When frying or cooking food with a strong aroma you may wish to select the Intensive setting level IV yellow indicator lamp for a short period 14 Automatic switch off of the Intensive setting You can set the Intensive setting so that it only runs for 10 minutes before reverting automatically to level Ill m To Set this option both the fan and the hob lighting must be switched off 515 m Press the run on option control for approximately 10 seconds The first fan setting indicator will light up m Then press in turn the hob lighting control 0000 the control and finally the hob lighting control again Operation The indicator lamps for fan power levels and IV will flash if the automatic switch off for the Intensive setting is not activated 0000 m Press the control to activate auto matic switch off The indicator lamps for fan power levels and IV will now light up constantly Press the control to deactivate the automatic switch off function 5215 m Press the run on option control to confirm your selection If you do not confirm your selection within 4 minutes the cooker hood will automatically revert to the original setting Run on option It is advisable to run the fan for a few minutes after cooking has finished to neutralise a
25. l filter is replaced before the operating hours counter has reached its maximum the charcoal filter touch control should be pressed for approximately 6 seconds to reset the counter 26 Cleaning and care Changing the halogen lamps Disconnect the cooker hood from the mains supply by switching it off at the isolator or at the wall socket and removing the plug or withdrawing the fuse from the fused spur connection unit or withdrawing the mains fuse or removing the screw out fuse in countries where this is applicable Exercise caution when changing halogen lamps They get very hot during use and remain hot for some time after being switched off Do not touch the surface directly when changing a lamp as grease particles from your fingers will adhere to the surface and damage it Please follow the manufacturer s instructions dai1749 m Remove the cover to the lamp To do this loosen the screws to the left and right of the cover unhook the lamp cover and take it downwards and off To avoid damaging the lighting or the hob below make sure you hold the lamp cover and halogen lamps securely at all times when handling them g A dai1756 m Pull the halogen lamp out of its socket m Gently push the new halogen lamp into the socket 20 W with G 4 connector and side reflector e g Osram MINISTAR with side reflector It is important that the halogen lamps
26. module XKM 2000 KM The hob transmits information about its operating status to the cooker hood via the household power supply Powerline When the hob is switched on the cooker hood lights and the fan also comes on During cooking the cooker hood automatically sets its power level according to the number of cooking zones in operation and their power levels After switching the hob off the fan and the lighting on the cooker hood will switch off automatically after a period of time For detailed information about this function please read the separate instruction booklet supplied with the XKM 2000 DA communication module The communication module is fitted to the cooker hood in the area of the motor and is connected to the controls of the cooker hood This module must be installed by a Miele service technician or suitably qualified electrician Operation To switch the fan on m Press the On Off control The fan runs at power level II The indicator lamp will come on If the cooker hood has been connected to a window contact switch via the Miele DSM 400 control module then the fan cannot be switched on if the window is shut The indicator lamp will flash To select a power level 0000 m Use the controls to select the power level required control control higher setting lower setting Depending on the intensity of the cooking vapours levels to II
27. nnot be held liable for unauthorised work P gt Faulty components must only be replaced by genuine Miele original parts The manufacturer can only guarantee the safety of the appliance when Miele replacement parts are used gt During installation maintenance and repair work the appliance must be disconnected from the mains electricity supply It is only completely isolated from the electricity supply when itis switched off at the isolator or the screw out fuse is removed in countries where this is applicable or the mains fuse is disconnected or it is switched off at the wall socket and the plug withdrawn or the fuse from the fused spur connection unit is withdrawn Warning and Safety instructions gt Do not connect the appliance to the mains electricity supply by a multi socket unit or an extension lead These do not guarantee the required safety of the appliance e g danger of overheating P gt For appliances with an external fan motor fitted EXT models the connection of the two units must be made using the connection cable and the plug connectors These models may only be combined with a Miele external motor P gt This appliance may only be used in mobile installations such as ships caravans aircraft etc if a risk assessment of the installation has been carried out by a suitably qualified engineer P In areas which may be subject to infestation by cockroaches o
28. ny lingering odours in the air whether you are using air extraction or recirculation mode The fan can be set to switch off automatically after either 5 or 15 minutes 5115 m After cooking has finished press the run on option control whilst the fan is still running Press once The fan will switch off after 5 minutes left hand indicator lamp Press twice The fan will switch off after 15 minutes right hand indicator lamp To switch off the run on option press the run on option control again The appliance will then not switch off automatically To switch the fan off L 0 m Press the On Off control to switch the fan off The indicator lamp will go out Operation To switch the hob lighting on The hob lighting can be switched on and off independently of the fan m Briefly press the lighting control to switch on the hob lighting The indicator lamp will come on The hob lighting will switch on at maximum brightness To dim the hob lighting The brightness of the lighting can be adjusted m With the lighting switched on press and hold the hob lighting control in The brightness will gradually dim until you release the control m Press the control in again to increase the brightness to the level required and then release it If you keep the control pressed in the light will continually change between bright and dim 16 To switch the hob ligh
29. of these catching fire m Replace the grease filter dai1803 m Replace the vapour plates First slide the side vapour plates in atthe top push sideways into place and click into place at the bottom dai1751 a m Fit the middle vapour plate into the slots at the top 1 then click into place at the bottom 2 24 o m After replacing the grease filter press the grease filter control for approximately 3 seconds to reset the operating hours counter The indicator lamp will go out m f the vapour plates and grease filter are cleaned before the operating hours counter has reached its maximum the grease filter touch control should be pressed for approximately 6 seconds to reset the counter to zero Cleaning and care Glass surfaces m Glass surfaces can be cleaned using a proprietary non abrasive cleaning agent designed specifically for use on glass Avoid oven sprays dai1753 m The glass canopy can be tilted forwards in order to clean it at the back Pull the lower edge forwards until it is vertical If you cannot pull the glass canopy forwards it is possible that the transport locking devices have not been loosened Follow the fitting instructions m After cleaning tilt the glass canopy back into position carefully You will feel a slight resistance when doing SO Fitting and replacing the charcoal filter I
30. oker hood is switched on the non return flap opens for the cooking vapours to be blown directly outside 12 air recirculation requires a conversion kit and charcoal filter see Technical Data ARR The air is drawn in and cleaned first by the vapour plates and the grease filter and then by a charcoal filter The cleaned air is then recirculated back into the kitchen through grilles in the top of the cooker hood extension piece Charcoal filters are available to order through your Dealer Chartered Agent or the Miele Spare Parts Department See back cover for contact details and Technical Data for model number Before using the cooker hood in recirculation mode ensure that the charcoal filter is in place See Cleaning and care an external motor EXT models only ARR EXT models are designed to be connected to an external motor located outside the room The external motor is connected to the cooker hood by means of a control cable and is operated by the controls on the cooker hood Miele home Con ctivity dai2385 This cooker hood is communication enabled Communication module XKM 2000 DA available as an optional extra enables the operation of the cooker hood to be automatically controlled by the operating status of a Miele electric hob with onset controls For communication to take place the hob must be fitted with communication
31. om when the cooker hood and the heater are in operation simultaneously an underpressure of 0 04 mbar 4 pa is the maximum permissible in the room dai1477 Ventilation can be maintained by air inlets which must not be blocked in windows doors and outside wall vents Or by other technical measures such as ensuring that the cooker hood can only be switched on when the heating appliance is switched off or vice versa A ventilation brick alone is not generally sufficient to ensure safe ventilation The overall ventilation condition of the dwelling must be taken into account If in any doubt the advice of a competent builder or for gas a qualified gas fitter Corgi registered in the UK must be sought One of the following technical measures may be necessary to ensure safe operation If the only way of ensuring adequate ventilation is via an open window a window contact switch should be fitted to ensure that the cooker hood can only operate when the window is opened sufficiently Take care when ventilating the room through an open window that ventilation is not impaired by a closed blind or curtain The cooker hood can be set up to automatically switch on an air intake fan or open a motorised inlet flap when it is switched on The cooker hood can be set up to automatically switch off a heating appliance which also depends on the air from the room wh
32. on the packaging 21 Cleaning and care Controls The controls may suffer discolouration or damage if soiling is left on them for too long Remove any soiling straight away Observe the General notes on cleaning earlier in this section Do not use stainless steel cleaning agents on the controls Vapour plates and grease filter The vapour plates and the re useable metal grease filter remove solid particles from the kitchen vapours grease dust etc preventing soiling of the cooker hood o The vapour plates and grease filter should be cleaned regularly at least every 3 4 weeks to avoid a build up of grease but always clean immediately if the grease filter control lamp comes on An oversaturated filter is a fire hazard Switch the hob lighting off and allow to cool down before removing the vapour plates to avoid any risk of burning yourself on the lighting 22 To avoid damaging the filter or the hob below make sure you hold the filter securely at all times when handling it dai1750 m First remove the vapour plate in the middle To do this pull the vapour plate out of its holder at the bottom 1 then press on the top and bring it down to remove it 2 z _ Ve Ai dai1808 Do not attempt to remove the side vapour plates by pulling down on the lower edge If the lighting is still hot there is danger of burning yourself
33. r other vermin pay particular attention to keeping the appliance and its surroundings in a clean condition at all times Any damage which may be caused by cockroaches or other vermin will not be covered by the guarantee Using at the same time as other heating appliances that depend on the air from the room Warning danger of toxic fumes Aa RE 7 B Great care should be taken when using the cooker hood at the same time and in the same room or area of the house as another heating appliance which depends on the air in the room Such appliances include gas oil wood or coal fired boilers and heaters continuous flow or other water heaters gas hobs cookers or ovens which draw air in from the room and duct exhaust gases out through a chimney or extraction ducting When used in extraction mode with or without an external motor fitted the appliance draws air in from the room in which it is installed and from neighbouring rooms If there is insufficient air an underpressure will occur The heating appliance may be starved of oxygen impairing combustion dai1474 Harmful gases could be drawn out of the chimney or extraction ducting back into the room with potentially fatal consequences Warning and Safety instructions In order to ensure safe operation and to prevent gases given off by the heating appliances from being drawn back into the ro
34. rating time which has already been used up tlamp 25 2lamps 50 3lamps 75 4lamps 100 The number of operating hours used remains in the memory even when the appliance is switched off or there is a power cut Operation Altering the grease filter operating hours counter The grease filter operating hours counter is set at the factory for 30 hours This can be lengthened or shortened to suit the type of cooking you do You can choose 20 30 40 or 50 hours Select a short time if you roast or fry a lot If you use very little fat for cooking select a longer time If you only cook occasionally we recommend that you still select a short time because grease which has built up gradually over a long period of time will harden on the filter and make cleaning more difficult O o m Press the On Off control to switch the fan off s45 co e m Press the run on option control and the grease filter control at the same time The indicator lamp for the grease filter control and one of the indicator lamps will flash 18 0060 The indicator lamps show the time which has been set tst lamp from the left 20 hours 2nd lamp from the left 30 hours 3rd lamp from the left 40 hours Ath lamp from the left 50 hours m Use the controls to select the desired time m Confirm the selection by pressing the grease filter control
35. the grease filter touch control lights up when the vapour plates and grease filter need to be cleaned The touch control is used to reset the operating hours counter every time the grease filter and vapour plates are cleaned see Cleaning and care It can also be used to check and alter the operating hours counter 43 Touch control for the charcoal filter The indicator lamp for the charcoal filter lights up when the charcoal filter used in recirculation mode needs to be replaced For this to happen the operating hours counter needs to be activated before the appliance is used for the first time The touch control is used to reset the operating hours counter every time the charcoal filter is replaced see Cleaning and care It can also be used to check and alter the operating hours counter For information about using the appliance see Operation 11 Modes of operation The cooker hood works with air extraction WRU The air is drawn in through the vapour plates cleaned by the grease filter and directed outside If the on site ventilation system does not have a non return flap then the non return flap supplied with the appliance must be fitted in the exhaust socket in the motor unit Having a non return flap fitted in the ducting ensures that air once ducted to the outside cannot get back into the room again The flap is closed when the cooker hood is switched off When the co
36. through your Miele Dealer Chartered Agent the Miele Spare Parts Department or via the internet on www miele shop com Housing General notes The surfaces and controls are susceptible to scratches and abrasions Please observe the following cleaning instructions m All external surfaces and controls can be cleaned using a Miele E Cloth or with warm water and a small amount of washing up liquid applied with a well wrung out soft sponge or cloth m Wipe the surfaces dry using a soft cloth Do not use too much water when cleaning the controls Water could penetrate into the electronics and cause damage Do not use cleaning agents containing soda acids chlorides or solvents abrasive cleaning agents e g powder cleaners or cream cleaners and abrasive sponges as well as pot scourers or sponges which have been used previously with abrasive cleaning agents These will damage the surface material Please observe the instructions below for cleaning the stainless steel housing the controls and glass surfaces Important for appliances with stainless steel housing This infomation does not apply to the controls Stainless steel surfaces can be cleaned using the Miele E Cloth or with a proprietary non abrasive cleaning agent designed specifically for use on stainless steel To help prevent re soiling a conditioning agent for stainless steel can also be used Follow the manufacturer s instructions
37. ting off m Press the hob lighting control briefly to switch the lighting off The indicator lamp will go out Safety cut out Should the cooker hood be left on the fan will switch off automatically after 10 hours The lighting will remain on Dau m Pressing the On Off control will switch the fan back on again Operation Filter operating hours counter The number of hours the appliance has been in operation is stored in memory The operating hours counter tells you when the grease filter or charcoal filter need to be cleaned or replaced Resetting the grease filter operating hours counter o After 30 hours of operation or another time if the operating hours counter has been altered the grease filter indicator lamp will light up The vapour plates and the grease filter must then be cleaned Afterwards the filter operating hours counter must be reset m Todo this press and hold the grease filter control for approximately 3 seconds while the fan is switched on The indicator lamp for the control will go out Reading the grease filter operating hours counter To check the percentage of time set already used Dune m Press the On Off control to switch the fan on m Press and hold the grease filter control 0006 One or more of the indicator lamps for the controls will flash The number of flashing lamps shows the percentage of the ope
Download Pdf Manuals
Related Search