Home
Gigabyte GA-MA74GMT-S2
Contents
1. Due to CPU limitation read the following guidelines before installing the memory in Dual Channel mode 1 Dual Channel mode cannot be enabled if only one DDR3 memory module is installed 2 When enabling Dual Channel mode with two memory modules it is recommended that memory of the same capacity brand speed and chips be used Hardware Installation 16 1 4 2 Installing a Memory Before installing a memory module make sure to turn off the computer and unplug the power AN cord from the power outlet to prevent damage to the memory module DDR3 and DDR2 DIMMs are not compatible to each other or DDR DIMMs Be sure to install DDR3 DIMMs on this motherboard E eE az EI DDR3 DIMM DDR3 memory module has a notch so it can only fit in one direction Follow the steps below to correctly install your memory modules in the memory sockets Step 1 Note the orientation of the memory module Spread the retaining clips at both ends of the memory socket Place the memory module on the socket As indicated in the picture on the le
2. 14 CLR_CMOS Clearing CMOS Jumper Use this jumper to clear the CMOS values e g date information and BIOS configurations and reset the CMOS values to factory defaults To clear the CMOS values place a jumper cap on the two pins to temporarily short the two pins or use a metal object like a screwdriver to touch the two pins for a few seconds 8 Open Normal a Short Clear CMOS Values e Always turn off your computer and unplug the power cord from the power outlet before clear A ing the CMOS values After clearing the CMOS values and before turning on your computer be sure to remove the jumper cap from the jumper Failure to do so may cause damage to the motherboard e After system restart go to BIOS Setup to load factory defaults select Load Optimized De faults or manually configure the BIOS settings refer to Chapter 2 BIOS Setup for BIOS configurations Hardware Installation 28 15 BAT Battery The battery provides power to keep the values such as BIOS configurations date and time information in the CMOS when the computer is turned off Replace the battery when the battery voltage drops to a low level o
3. T SATA2 0 1 2 3 SATA 3Gb s Connectors The SATA connectors conform to SATA 3Gb s standard and are compatible with SATA 1 5Gb s standard Each SATA connector supports a single SATA device The AMD SB710 controller supports RAID 0 RAID 1 RAID 10 and JBOD Refer to Chapter 5 Configuring SATA Hard Drive s for instructions on configur ing a RAID array SATA2 0 7 Pin No Definition GND TXP TXN GND RXN RXP GND 1 SATA2 2 0 4 SATA2 1 NED Oo BB ow ND gt Please connect the L shaped end of the SATA cable to your SATA hard drive e A RAID 0 or RAID 1 configuration requires at least two hard drives If more than two hard drives are to be used the total number of hard drives must be an even number e ARAID 10 configuration requires at least four hard drives and the total number of hard drives must be an even number Hardware Installation 294 8 F_PANEL Front Panel Header Connect the power switch reset switch speaker chassis intrusion switch sensor and system status indicator on the chassis to this header according to the pin assign
4. Hardware Installation 22 3 4 CPU FAN SYS FAN Fan Headers 5 The motherboard has a 4 pin CPU fan header CPU_FAN and a 3 pin SYS_FAN system fan headers Most fan headers possess a foolproof insertion design When connecting a fan cable be sure to connect it in the correct orientation the black connector wire is the ground wire The motherboard supports CPU fan speed control which requires the use of a CPU fan with fan speed control design For optimum heat dissipation it is recommended that a system fan be installed inside the chassis gx oo t CPU FAN ja SYS FAN CPU FAN Pin No Definition 1 GND 2 12V Speed Control 3 Sense 4 Speed Control SYS_FAN Pin No Definition 1 GND 2 12V 3 Sense e Be sure to connect fan cables to the fan headers to prevent your CPU and system from over heating Overheating may result in damage to the CPU or the system may hang e These fan headers are not configuration jumper blocks Do not place a jumper cap on the headers FDD Floppy Disk Drive Connector This connector is used to connect a floppy disk
5. TT 5 1 3 Installing the SATA RAID AHCI Driver and Operating System T9 5 2 Configuring Audio Input and Output 83 5 2 1 Configuring 2 4 5 1 7 1 Channel Audio 83 9 2 2 CONMOUNNG 3s PDF AIM OURS ANA ANG 86 5 2 3 Configuring Microphone Recording nananana sanan 88 5 2 4 Using the Sound Recorder nennen 90 s TOM Si NG MT DU 91 5 3 14 Frequently Asked Questions screens 91 5 3 2 Troubleshooting PTOCedUle uec etn eec sar eben 92 5 4 Regulatory Statements sess 94 Box Contents M GA MA74GMT S2H or GA MA74GMT S2 motherboard M Motherboard driver disk MI User s Manual MI One IDE cable vI Two SATA cables V I O Shield The box contents above are for reference only and the actual items shall depend on the product package you obtain The box contents are subject to change without notice The motherboard image is for reference only Optional Items Floppy disk drive cable Part No 12CF1 1FD001 7 R 2 port USB 2 0 bracket Part No 12CR1 1UB030 5 R 2 port SATA power cable Part No 12CF1 2SERPW 0 R O S PDIF In and Out cable Part No 12CR1 1SPINO 1 R COM port cable Part No 12CF1 1CM001 3 R GA MA74GMT S2H GA MA74GMT S2 Motherboard Layout BHBBE F AUDIO PCIEX1 n C PCIEX16 CDC CT ora RTL81 1D E PCI SPDIF_IO SYS FAN CLR CMOS F USB2 F USB1 Only for GA MA74GMT S2H GA MA74GMT S2H GA MA74GMT S2 Motherboard Block Diagra
6. E will appear Enter a passkey 8 16 digits recommended which will be used for pairing Mer with the cell phone Then enter the same passkey on your cell phone NT Nu Configuration Configuring other Bluetooth settings pam 4 On the Other Settings tab you can set how much time it takes to scan your Bluetooth pem cell phone key how many times to rescan the key to make sure it is in range of your meg Duran pibe Mean Formae QN Rb pari in d EF R computer and when to turn off the hard drive if the system energy saving state lasts Too over the predetermined period of time After completing the settings click Set for the iher 3 mina settings to take effect and then click Exit to quit Device Scan Time sec Set the length of time Auto Green scans your Bluetooth cell phone key ranging from 5 to 30 seconds in 5 second increment Auto Green searches for the key based on the length of time you set Rescan Times Set how many times Auto Green will rescan your Bluetooth cell phone key if it does not detect it ranging from 2 to 5 times Auto Green will keep rescanning according to the times you set When the times limit is reached and your Bluetooth cell phone key is still not detected the system will enter the selected energy saving mode e Turn off HD Set when to turn off the hard drive If the system inactivity time exceeds the specified time
7. No The power supply CPU or 9 3 When the computer is turned on is the CPU cooler running En CPU socket might fail Yes The problem is verified and solved The graphics card Check if there is display on your monitor expansion slot or monitor might fail The problem is verified and solved Turn off the computer Plug in the keyboard and mouse and restart the computer Check if the keyboard is working properly No The keyboard or keyboard connector might fail The problem is verified and solved Yes Press lt Delete gt to enter BIOS Setup Select Load Fail Safe De faults or Load Optimized Defaults Select Save 4 Exit Setup to save changes and exit BIOS Setup The IDE SATA device Turn off the computer and connect the IDE SATA devices Check if the system can boot successfully connector or cable might fail Yes The problem is verified and solved Reinstall the operating system Reinstall other devices one by one install one device at one time and then boot the system to see if the device works successfully dealer for help Or go to the Support amp Downloads Technical Service Zone page to submit your e the procedure above is unable to solve your problem contact the place of purchase or local question Our customer service staff will reply you as soon as possible 93 Appendix 5 4 Regulatory Statements Regulatory Notices This document must not be copied
8. To configure 7 1 channel audio you have to use an HD front panel audio module and enable themulti channel audio feature through the audio driver Refer to the instructions on setting up a 2 4 5 1 7 1 channel audio configuration in Chapter 5 Configuring 2 4 5 1 7 1 Channel Audio When removing the cable connected to a back panel connector first remove the cable from your device and then remove it from the motherboard When removing the cable pull it straight out from the connector Do not rock it side to side to prevent an electrical short inside the cable connector Em 1 7 Internal Connectors 1 ATX 12V 9 F AUDIO 2 ATX 10 CD IN 3 CPU FAN 11 SPDIF IO 4 SYS FAN 12 F USB F USB2 5 FDD 13 COM 6 IDE 14 CLR CMOS 7 SATA2 0 1 2 3 15 BAT 8 F PANEL Read the following guidelines before connecting external devices First make sure your devices are compliant with the connectors you wish to connect Before installing the devices be sure to turn off the devices and your computer Unplug the power cord from the power outlet to prevent damage to the devices After installing the device and before turning on the computer make sure the device cable has been securely attached to the connector on the motherboard 227 Hardware Installation 1 2 ATX_12V ATX 2x2 12V Power Connector and 2x12 Main Power Connector With the use of the power connector the power supply can supply enough
9. Co AX oL OT ee ba Step 1 Step 2 First attach the connector at the end of the cable Secure the metal bracket to the chassis back to the SPDIF IO header on your motherboard panel with a screw B Configuring S PDIF In The S PDIF In jacks on the SPDI F In and Out cable allow you to input digital audio signals to the computer for audio processing Step dpi Rash mD Jas iua Cas After connecting the S PDIF In device access the Digital In Bees we ED put screen Click the Default Format tab to select the default lat E format Click OK to complete mm 3 E e ect Fu suma er rd db b ud ha sr m del om i Note The actual locations of the SPDIF In and SPDIF Out connectors may differ by model Appendix 86 C Configuring S PDIF Out The S PDIF Out jacks can transmit audio signals to an external decoder for decoding to get the best audio quality To output S PDIF digital audio signals to an external decoder connect a S PDIF coaxial cable or a S PDIF optical cable either one to the optical coxial S PDIF out connector on the motherboard back panel or on the optional S PDIF In and Out cable C 1 Conneting a S PDIF Out Cable S PDIF Coaxial Cable S PDIF Optical Cable C 2 Configuring S PDIF Out Step On the Digital Output screen click the Default Format tab and then select the sample rate and bit depth Click OK to complete diee pea oca ig edel nd fa Rem d aa hem pacem cac PEU ar cusam
10. FAX 1 626 854 9339 Correo soporte gigabyte usa com Tech Support http rma gigabyte us Web address http latam giga byte com e Giga Byte SINGAPORE PTE LTD Singapore WEB address http www gigabyte sg e Thailand WEB address http th giga byte com e Vietnam WEB address http www gigabyte vn 99 e NINGBO G B T TECH TRADING CO LTD China WEB address http www gigabyte cn Shanghai TEL 86 21 63410999 FAX 86 21 63410100 Beijing TEL 86 10 62102838 FAX 86 10 62102848 Wuhan TEL 86 27 87851061 FAX 86 27 87851330 GuangZhou TEL 86 20 87540700 FAX 86 20 87544306 Chengdu TEL 86 28 85236930 FAX 86 28 85256822 Xian TEL 86 29 85531943 FAX 86 29 85510930 Shenyang TEL 86 24 83992901 FAX 86 24 83992909 GIGABYTE TECHNOLOGY INDIA LIMITED India WEB address http www gigabyte in e Saudi Arabia WEB address http www gigabyte com sa e Gigabyte Technology Pty Ltd Australia WEB address http www gigabyte com au Appendix e G B T TECHNOLOGY TRADING GMBH Germany e Hungary WEB address http www gigabyte de WEB address http www giga byte hu e G BT TECH CO LTD UK Turkey WEB address http www giga byte co uk WEB address http ww gigabyte com tr e Giga Byte Technology B V The Netherlands Russia WEB address http www giga byte nl WEB addr
11. b gt Any KEY Press any key on the keyboard to turn on the system gt gt Keyboard 98 Press POWER button on the Windows 98 keyboard to turn on the system lt gt KB Power ON Password Set the password when Power On by Keyboard is set to Password Press lt Enter gt on this item and set a password with up to 5 characters and then press lt Enter gt to accept To turn on the system enter the password and press lt Enter gt Note To cancel the password press lt Enter gt on this item When prompted for the password press lt En ter gt again without entering the password to clear the password settings lt AC Back Function Determines the state of the system after the return of power from an AC power loss gt gt Soft Off The system stays off upon the return of the AC power Default gt gt Full On The system is turned on upon the return of the AC power bp Memory The system returns to its last known awake state upon the return of the AC power lt Power On by Alarm Determines whether to power on the system at a desired time Default Disabled If enabled set the date and time as following gt Date of Month Alarm Turn on the system at a specific time on each day or on a specific day in a month Resume Time hh mm ss Set the time at which the system will be powered on automatically Note When using this function avoid inadequate shutdown from the operating system or removal of the AC power or the settings ma
12. users can quickly create backups of changed data files 1 or copy files from a spe cific backup on PATA and SATA hard drives partitioned on NTFS file system in Windows Vista m Instructions wie In the main menu click the Config button to open the Smart Recov n g ery Preference dialog box The Smart Recovery Preference dialog box PRG RE segs Button Function CE Enable Enables automatic daily backup gt Schedule Sets a daily backup schedule 2 Capacity Sets the percentage of hard drive space used for saving backups N3 The hard drive must have more than 1 CB of capacity ER Each partition can accommodate up to 64 backups the actual limit depends on the size of each partition When this limit is reached the oldest backup will be ovewritten Instructions for copying files folders from a backup To browse through your backups made at different time select a backup time using the time scroll bar on the right or at the bottom of the screen If you want to copy back a file folder select the file folder you wish to copy and click the Copy button The files folders listed on the screen are read only so you cannot edit their contents Note 1 The changed data refers to the data that has been modified deleted or newly added since the last backup Note 2 The system will make an automatic backup on changed data only once everyday If the computer is turned on for a long time the backup wi
13. 1984 2010 Award Software SMART LAN Start detecting at Port Item Help Part1 2 Status Open Length Menu Level bb Part3 6 Status Open Length Part4 5 Status Open Length Part7 8 Status Open Length Ne Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults This motherboard incorporates cable diagnostic feature designed to detect the status of the attached LAN cable This feature will detect cabling issue and report the approximate distance to the fault or short Refer to the following information for diagnosing your LAN cable o When No LAN Cable Is Attached If no LAN cable is attached to the motherboard the Status fields of all four pairs of wires will show Open and the Length fields show 0m as shown in the figure above lt gt When LAN Cable Is Functioning Normally If no cable problem is detected on the LAN cable connected to a Gigabit hub or a 10 100 Mbps hub the following message will appear Start detecting at Port Link Detected gt 100Mbps Cable Length 30m gt gt Link Detected Displays transmission speed gt Cable Length Displays the approximate length of the attached LAN cable Note The Gigabit hub will only operate at a speed of 10 100 Mbps in MS DOS mode it will operate at a normal speed of 10 100 1000 Mbps in Windows mode or when the LAN Boot ROM is activated o When a Cable Problem Occu
14. Chapter 3 Drivers Installation Before installing the drivers first install the operating system ER After installing the operating system insert the motherboard driver disk into your optical drive The driver Autorun screen is automatically displayed which looks like that shown in the screen shot below If the driver Autorun screen does not appear automatically go to My Computer double click the optical drive and execute the Run exe program 3 1 Installing Chipset Drivers E Now Loading Please wait After inserting the driver disk Xpress Install will automatically scan your system and then list all the drivers that are recommended to install You can click the Install All button and Xpress Install will install all the rec ommended drivers Or click Install Single Items to manually select the drivers you wish to install Install Chipset Drivers We pec enne Eat you ral te derer ntes Eden l or your meorherbeard Please chek Talal AT lo restat al Th drivers Samalt al Ci Eos Congal Leslie Venen 11 13 0 Size 6 TME ny agieren the internet mah axeerienzs kad en your country and languag and adda orina gru 15 ur TILA a o AT RSTI VGA NOU NULL 1 Size 144 SUR ATi AETH VA Dri kor Vida A Windows T m Peabek HO Adio Driver Mansion Ra 456133 ates high Dainetion Audi Dea mi Reset ETTIESES LAM driver ce gigabit Vista anions 238 022 2010 pr Wara used 5 la when Xpress Install is install
15. F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults lt Date mm dd yy Sets the system date The date format is week read only month date and year Select the desired field and use the up arrow or down arrow key to set the date Time hh mm ss Sets the system time For example 1 p m is 13 0 0 Select the desired field and use the up arrow or down arrow key to set the time o IDE Channel 0 Master Slave gt IDE HDD Auto Detection Press lt Enter gt to autodetect the parameters of the IDE SATA device on this channel gt gt IDE Channel 0 Master Slave Configure your IDE SATA devices by using one of the two methods below Auto Lets the BIOS automatically detect IDE SATA devices during the POST Default None If no IDE SATA devices are used set this item to None so the system will skip the detection of the device during the POST for faster system startup Access Mode Sets the hard drive access mode Options are Auto default CHS LBA Large lt IDE Channel 2 3 Master Slave gt gt IDE Auto Detection Press Enter to autodetect the parameters of the IDE SATA device on this channel Extended IDE Drive Configure your IDE SATA devices by using one of the two methods below Auto Lets the BIOS automatically detect IDE SATA devices during the POST Default None If no IDE SATA devices are used set this item to None so the system will skip the detection of the device during the POST for fas
16. Off by Power button Instant off Menu Level gt USB Wake Up from S3 Enabled Modem Ring Resume Disabled PME Event Wake Up Enabled HPET Support N Enabled Power On By Mouse Disabled Power On By Keyboard Disabled lt KB Power ON Password Enter AC Back Function Soft Off Power On by Alarm Disabled Date of Month Everyday Resume Time hh mm ss 0 0 0 ErP Support Disabled 112 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults c ACPI Suspend Type Specifies the ACPI sleep state when the system enters suspend gt gt S1 POS Enables the system to enter the ACPI S1 Power on Suspend sleep state In S1 sleep state the system appears suspended and stays in a low power mode The system can be resumed at any time b gt S3 STR Enables the system to enter the ACPI S3 Suspend to RAM sleep state default In S3 sleep state the system appears to be off and consumes less power than in the S1 state When signaled by a wake up device or event the system resumes to its working state exactly where it was left off c Soft Off by Power button Configures the way to turn off the computer in MS DOS mode using the power button gt gt Instant Off Press the power button and then the system will be turned off instantly Default Delay 4 Sec Press and hold the power button for 4 seconds to turn off the system If the power button i
17. Up 4 Down ESC Exit Space Change Ctrl Y Save PgUp Dn Page Change Figure 5 Appendix 14 In the following procedure we ll create RAID 0 as an example Under the RAID Mode section press the SPACE key to select RAID 0 Set the Stripe Block size 64 KB is the default Under the Drives Assignments section press the up or down arrow key to highlight a drive Press the lt SPACE gt key or lt Y gt to change the Assignment option to Y This action adds the drive to the disk array The Total Drv section will show the number of disks assigned 5 Press lt Ctrl gt lt Y gt keys to save the information The window below will appear B N Fast Initialization option has been selected It will erase the MBR data of the disk Press Ctrl Y key if you are sure to erase it gt Press any other key to ignore this option Figure 6 6 Press lt Ctrl gt lt Y gt to clear the MBR or press other keys to ignore this option Then the window below will appear Press Ctrl Y to Modify Array Capacity or press any other key to use maximum capacity Figure 7 7 Press lt Ctrl gt lt Y gt to set the capacity of the RAID array or press other keys to set the array to its maxi mum capacity 8 After the creation is complete the screen will return to Define LD Menu where you will see the newly created array 9 Press lt Esc gt to return to Main Menu and press lt Esc gt again if you want to e
18. a cd nim mut am GIGABYTE i 87 Appendix 5 2 3 Configuring Microphone Recording Step 1 After installing the audio driver the HD Audio Manager icon Bil will appear in the notification area Double click the icon to access the HD Audio Manager cs 5 45 PM Step 2 Connect your microphone to the Mic in jack pink on the back panel or the Mic in jack pink on the front panel Then configure the jack for microphone function ality Note The microphone functions on the front panel and back panel cannot be used at the same time Step 3 Go to the Microphone screen Do not mute the record ing volume or you ll not be able to record the sound To hear the sound being recorded during the recording process do not mute the playback volume It is recom mended that you set the volumes at a middle level If you want to change the current sound input default device to microphone right click on Mi crophone and select Set Default Device Appendix 88 Step 4 To raise the recording and playback volume for the microphone click the Microphone Boost icon on the right of the Recording Volume slider and set the Microphone Boost level Step 5 After completing the settings above click Start point to All Programs point to Accessories and then click Sound Recorder to begin the sound recording Enabling Stereo Mix If the HD Audio Manager does not display the recording device yo
19. and may differ by BIOS version ER If you do not find the settings you want in the Main Menu or a submenu press lt Ctrl gt lt F1 gt to 33 BIOS Setup The Functions of the lt F11 gt and lt F12 gt keys For the Main Menu Only gt F11 Save CMOS to BIOS This function allows you to save the current BIOS settings to a profile You can create up to 8 profiles Profile 1 8 and name each profile First enter the profile name to erase the default profile name use the SPACE key and then press lt Enter gt to complete gt F12 Load CMOS from BIOS If your system becomes unstable and you have loaded the BIOS default settings you can use this function to load the BIOS settings from a profile created before without the hassles of reconfiguring the BIOS settings First select the profile you wish to load then press lt Enter gt to complete MB Intelligent Tweaker M I T Use this menu to configure the clock frequency and voltages of your CPU memory etc Standard CMOS Features Use this menu to configure the system time and date hard drive types floppy disk drive types and the type of errors that stop the system boot etc Advanced BIOS Features Use this menu to configure the device boot order advanced features available on the CPU and the pri mary display adapter Integrated Peripherals Use this menu to configure all peripheral devices such as IDE SATA USB integrated audio and inte grated LAN etc Power Manag
20. assigned to arrays press lt 1 gt to enter the View Drive Assignments window To create an array press lt 2 gt to enter the Define LD window To delete an array press lt 3 gt to enter the Delete LD window To view controller settings press lt 4 gt to enter the Controller Configuration window Main Menu View Drive Assignments Define LD Delete LD Controller Configuration Keys Available Press 1 4 to Select Option ESC Exit Figure 3 73 Appendix Create Arrays Manually To create a new array press s27 to enter the Define LD Menu window Figure 4 The Define LD selection from the Main Menu allows users to begin the process of manually defining the drive elements and RAID levels for one or multiple disk arrays Option ROM Utility c 2008 Advanced Micro Devices Inc Define LD Menu No RAID Mode Total Drv Capacity GB Status Keys Available 1 Up 4 Down ESC Exit Enter Select Figure 4 In Figure 4 use the up or down arrow key to move to a logical disk set and press lt Enter gt to enter the RAID configuration menu Figure 5 Option ROM Utility c 2008 Advanced Micro Devices Inc Define LD Menu RAID Mode Total Drv ED RAID 0 0 Stripe Block 64 KB Fast Init ON Gigabyte Boundary ON Cache Mode WriteThru Drives Assignments Channel ID Capabilities Capacity GB Assignment BEA OA DE 10100 DPA ENIN SATA 3G 79 89 Ni AVER Keys Available 1
21. be monibanrd or controlled va a Face Wizard provides utility for custamining BOS Boot up sonen 3 3 Technical Manuals This page provides GIGABYTE s application guides content descriptions for this driver disk and the mother board manuals GIGABYTE Eua ce D Drivers Installation 56 3 4 Contact For the detailed contact information of the GIGABYTE Taiwan headquarter or worldwide branch offices click the URL on this page to link to the GIGABYTE website GIGABYTE 3 5 System This page provides the basic system information GIGABYTE Gigabyte Technology Co Lid GAMATAGUT 82 GA MATIGMT S2 Fig AMD Phenom E X4 945 Processor Total physical memory 593 NG AND NEW T SERIES Driver DVO 1 3 200 0708 1 5 Drivers Installation 3 0 Download Center To update the BIOS drivers or applications click the Download Center button to link to the GIGABYTE website The latest version of the BIOS drivers or applications will be displayed GIGABYTE Install Chipset Drivers We past erue est pou natal the diers ined balas kor your motherboard Please click Talal AIT lo Plan al The divers automatic ally k var F ss UL a T pr aa ee 4 a mamam aa B F set EVES LAM driver ba gigabit Ni 3 7 New Utilities This page provides a quick link t
22. the settings to defaults gt gt All Cores Configures Advanced Clock Calibration for all CPU cores gt Per Core Individually configures Advanced Clock Calibration for each CPU core Value All Cores This option is configurable only when Advanced Clock Calibration is set to All Cores Options are 12 12 Value Core 0 Value Core 1 Value Core 2 Value Core 3 This option is configurable only when Advanced Clock Calibration is set to Per Cores Options are 12 12 CPU core Control Allows you to determine whether to manually enable disable CPU Core 1 2 3 4 5 Manual allows the CPU Core 1 2 3 4 5 items below to be configurable gt gt Auto Lets the BIOS to enable all CPU cores number of cores available depends on the CPU being used Default Manual Allows you to individually enable disable CPU Core 1 2 3 4 5 CPU core 1 2 3 4 5 Note Enables or disables CPU Core 1 2 3 4 5 Default Enabled HT Link Frequency Allows you to manually set the frequency for the HT Link between the CPU and chipset gt gt Auto BIOS will automatically adjust the HT Link Frequency Default gt gt 200 MHz 1 GHz Sets HT Link Frequency to 200 MHz 1 GHz CPU Clock Ratio Allows you to alter the clock ratio for the installed CPU The adjustable range is dependent on the CPU being used CPU NorthBridge Freq t9 Allows you to alter the North Bridge controller frequency for the installed CPU The adjustable range is depend
23. to BIOS Setup to make any required BIOS changes for your expansion card s T Install the driver provided with the expansion card in your operating system D M ga GO De zt Example Installing and Removing a PCI Express Graphics Card e Installing a Graphics Card Gently push down on the top edge of the card until it is fully inserted into the PCI Express slot Make sure the card is securely seated in the slot and does not rock e Removing the Card Gently push back on the lever on the slot and then lift the card straight out from the slot Hardware Installation 18 1 6 Back Panel Connectors C 00000 00000 e USB 2 0 1 1Port The USB port supports the USB 2 0 1 1 specification Use this port for USB devices such as a USB key board mouse USB printer USB flash drive and etc PS 2 Keyboard Mouse Port Use this port to connect a PS 2 Keyboard or mouse D Sub Port The D Sub port supports a 15 pin D Sub connector Connect a monitor that supports D Sub connection to this port DVI D Port Note 2 The DVI D port conforms to the DVI D specification and supports a maximum resolution of 1920x1200 the actual resolutions supported depend on the monitor being used Connect a monitor that supports DVI D con nection to this port HDMI Port D The HDMI High Definition Multimedia Interface provides an all digital audio video interface to transmit the uncompressed audio video signals an
24. to set the South Bridge voltage gt gt Normal Supplies the South Bridge voltage as required Default pp 0 1V 0 3V The adjustable range is from 0 1V to 0 3V lt CPU NB VID Control Note Allows you to set the CPU Northbridge VID voltage Auto sets the CPU Northbridge VID voltage as re quired The adjustable range is dependent on the CPU being installed Default Normal Note Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU c CPU Voltage Control Allows you to set the CPU voltage Auto sets the CPU voltage as required The adjustable range is de pendent on the CPU being installed Default Normal Note Increasing CPU voltage may result in damage to your CPU or reduce the useful life of the CPU Normal CPU Vcore Displays the normal operating voltage of your CPU Note This item appears only if you install a CPU that supports this feature 39 BIOS Setup 2 4 Standard CMOS Features CMOS Setup Utility Copyright C 1984 2010 Award Software Standard CMOS Features Date mm dd yy Tue Jul 13 2010 Item Help Time hh mm ss oH Menu Level gt IDE Channel 0 Master IDE Channel 0 Slave IDE Channel 2 Master IDE Channel 2 Slave IDE Channel 3 Master IDE Channel 3 Slave Drive A 1 44M 3 5 Floppy 3 Mode Support Disabled Halt On All But Keyboard Base Memory 640K Extended Memory 894M 142 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help
25. without our written permission and the contents there of must not be imparted to a third party nor be used for any unauthorized purpose Contravention will be prosecuted We believe that the information contained herein was accurate in all respects at the time of printing GIGABYTE cannot however assume any responsibility for errors or omissions in this text Also note that the informa tion in this document is subject to change without notice and should not be construed as a commitment by GIGABYTE Our Commitment to Preserving the Environment In addition to high efficiency performance all GIGABYTE motherboards fulfill European Union regulations for RoHS Restriction of Certain Hazardous Substances in Electrical and Electronic Equipment and WEEE Waste Electrical and Electronic Equipment environmental directives as well as most major worldwide safety requirements To prevent releases of harmful substances into the environment and to maximize the use of our natural resources GIGABYTE provides the following information on how you can responsibly recycle or reuse most of the materials in your end of life product Restriction of Hazardous Substances RoHS Directive Statement GIGABYTE products have not intended to add and safe from hazardous substances Cd Pb Hg Cr 6 PBDE and PBB The parts and components have been carefully selected to meet RoHS requirement More over we at GIGABYTE are continuing our efforts to develop products that
26. 008 Advanced Micro Devices Inc RAID Mode Total Drv Capacity GB Status Stripe Block Cache Mode s Channel ID Drive Model Capabilities Capacity GB Press Ctrl Y to delete the data in the disk or press any other key to abort ee NN Figure 9 Appendix 16 5 1 2 Making a SATA RAID AHCI Driver Diskette Required for AHCI and RAID Mode To successfully install operating system onto SATA hard drive s that is are configured to RAID AHCI mode you need to install the SATA controller driver during the OS installation Without the driver the hard drive may not be recognized during the Windows setup process First of all copy the driver for the SATA controller from the motherboard driver disk to a floppy disk For installing Windows Vista you also can copy the SATA con troller driver from the motherboard driver disk to a USB flash drive See the instructions below about how to copy the driver in MS DOS and Windows mode In MS DOS mode Prepare a startup disk that has CD ROM support and a blank formatted floppy disk Steps 1 Boot from the startup disk 2 Remove the startup disk and insert the prepared floppy disk and the motherboard driver disk here we as sume that the drive letter for your optical drive is D 3 At the A3 prompt type the following command Press Enter after the command Figure 1 Ary gt copy dirXbooturvXisbxxx x86 Nos Figure 1 Note Type the driver directory bas
27. 854 9339 hereby declares that the product Product Name Motherboard Model Number GA MA74GMT S2H GA MA74GMT S2 Conforms to the following specifications FCC Part 15 Subpart B Section 15 107 a and Section 15 109 a Class B Digital Device Supplementary Information This device complies with part 15 of the FCC Rules Operation is subject to the following two conditions 1 This device may not cause harmful and 2 this device must accept any inference received including that may cause undesired operation Representative Person s Name ERIC LU Signature ric Li Date Jul 9 2010 Copyright 2010 GIGA BYTE TECHNOLOGY CO LTD All rights reserved The trademarks mentioned in this manual are legally registered to their respective owners Disclaimer Information in this manual is protected by copyright laws and is the property of GIGABYTE Changes to the specifications and features in this manual may be made by GIGABYTE without prior notice No part of this manual may be reproduced copied translated transmitted or published in any form or by any means without GIGABYTE s prior written permission Documentation Classifications In order to assist in the use ofthis product GIGABYTE provides the following types of documentations m For detailed product information carefully read the User s Manual M For instructions on how to use GIGABYTE s unique features read or download the information on from the Support amp DownloadsWothe
28. A74GMT S2H Hardware Installation mi Internal goe Connectors 9 2 9 9 1 x 24 pin ATX main power connector 1 x 4 pin ATX 12V power connector 1 x floppy disk drive connector 1 x IDE connector 4 x SATA 3Gb s connectors 1 x CPU fan header 1 x system fan header 1 x front panel header 1 x front panel audio header 1 x CD In connector 1 x S PDIF In Out header 2 x USB 2 0 1 1 headers 1 x serial port header 1 x clearing CMOS jumper lt Back Panel Connectors 1 x PS 2 keyboard mouse port 1 x D Sub port 1 x DVI D port Note 2 Note 3 1 x HDMI port QD es 3 8 x USB 2 0 1 1 ports 1 x RJ 45 port 3 x audio jacks Line In Line Out Microphone O 1 0 Controller Hard Monit ardware Moni i ITE IT8718 chip System voltage detection CPU System temperature detection CPU System fan speed detection CPU overheating warning CPU System fan fail warning CPU fan speed control 9 BIOS NTG 9 2 x 8 Mbit flash Use of licensed AWARD BIOS Support for DualBIOS PnP 1 0a DMI 2 0 SM BIOS 2 4 ACPI 1 0b Only for GA MA74GMT S2H 11 Hardware Installation Unique Features Support for BIOS Support for Q Flash Support for Xpress BIOS Rescue Support for Download Center e Support for Xpress Install e Support for Xpress Recovery2 Support for EasyTune N0 9 e Support for Smart Recovery e Support for Auto Green Supp
29. Advanced BIOS Features Set Supervisor Password Integrated Peripherals Set User Password Power Manageme PnP PCI Configur Enter Password PC Health Status ESC Quit le Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Change Set Disable Password Press lt Enter gt on this item and type the password with up to 8 characters and then press lt Enter gt You will be requested to confirm the password Type the password again and press lt Enter gt The BIOS Setup program allows you to specify two separate passwords Supervisor Password When a system password is set and the Password Check item in Advanced BIOS Features is set to Setup you must enter the supervisor password for entering BIOS Setup and making BIOS changes When the Password Check item is set to System you must enter the supervisor password or user password at system startup and when entering BIOS Setup User Password When the Password Check item is set to System you must enter the supervisor password or user password at system startup to continue system boot In BIOS Setup you must enter the supervisor password if you wish to make changes to BIOS settings The user password only allows you to view the BIOS settings but not to make changes To clear the password press lt Enter gt on the password item and when requested for the password press lt Enter gt again The message PASSWORD DISABLED will appear ind
30. EM FAN Fail Warning Allows the system to emit warning sound if the CPU system fan is not connected or fails Check the fan condition or fan connection when this occurs Default Disabled c CPU Smart FAN Control Enables or disables the CPU fan speed control function Enabled allows the CPU fan to run at different speed according to the CPU temperature You can adjust the fan speed with EasyTune based on system requirements If disabled the CPU fan runs at full speed Default Enabled BIOS Setup 50 CPU Smart FAN Mode Specifies how to control CPU fan speed This item is configurable only if CPU Smart FAN Control is set to Enabled gt gt Auto Lets the BIOS automatically detect the type of CPU fan installed and sets the optimal CPU fan control mode Default Voltage Sets Voltage mode for a 3 pin CPU fan bp PWM Sets PWM mode for a 4 pin CPU fan lt System Smart FAN Control Enables or disables the system fan speed control function Enabled allows the system fan to run at dif ferent speed according to the system temperature If disabled system fan runs at full speed Default Enabled 51 BIOS Setup 2 10 Load Fail Safe Defaults CMOS Setup Utility Copyright C 1984 2010 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Peripherals Set User Password Power Manageme il PnP PCI Configur Lo
31. EM FAN Speed 0 RPM CPU Warning Temperature Disabled CPU FAN Fail Warning Disabled SYSTEM FAN Fail Warning Disabled CPU Smart FAN Control Enabled CPU Smart FAN Mode Auto System Smart FAN Control Enabled Ti lt e Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Reset Case Open Status Keeps or clears the record of previous chassis intrusion status Enabled clears the record of previous chassis intrusion status and the Case Opened field will show No at next boot Default Disabled Case Opened Displays the detection status of the chassis intrusion detection device attached to the motherboard CI header If the system chassis cover is removed this field will show Yes otherwise it will show No To clear the chassis intrusion status record set Reset Case Open Status to Enabled save the settings to the CMOS and then restart your system c Current Voltage V Vcore DDR3 1 5V 3 3V 12V Displays the current system voltages lt gt Current System CPU Temperature Displays current system CPU temperature lt Current CPU SYSTEM FAN Speed RPM Displays current CPU system fan speed lt CPU Warning Temperature Sets the warning threshold for CPU temperature When CPU temperature exceeds the threshold BIOS will emit warning sound Options are Disabled default 60 C 140 F 70 C 158 F 80 C 176 F 90 C 194 F c CPU SYST
32. ESD wrist strap when handling electronic com ponents such as a motherboard CPU or memory If you do not have an ESD wrist strap keep your hands dry and first touch a metal object to eliminate static electricity Prior to installing the motherboard please have it on top of an antistatic pad or within an electrostatic shielding container Before unplugging the power supply cable from the motherboard make sure the power sup ply has been turned off Before turning on the power make sure the power supply voltage has been set according to the local voltage standard Before using the product please verify that all cables and power connectors of your hard ware components are connected To prevent damage to the motherboard do not allow screws to come in contact with the motherboard circuit or its components Make sure there are no leftover screws or metal components placed on the motherboard or within the computer casing Do not place the computer system on an uneven surface Do not place the computer system in a high temperature environment Turning on the computer power during the installation process can lead to damage to sys tem components as well as physical harm to the user If you are uncertain about any installation steps or have a problem related to the use of the product please consult a certified computer technician 9 Hardware Installation 1 2 Product Specifications 6 CPU GO Hyper Transport Bus Support
33. GA MA74GMT S2H GA MA74GMT S2 AM3 socket motherboard for AMD Phenom II processor AMD Athlon II processor User s Manual Rev 1401 12ME MA74GMT2 1401R Declaration of Conformity We Manufacturer importer full asd waa G B T Technology Trading GMbH Bullenkoppel 16 22047 Hamburg Germany declare that the product descripton of the apparatus system installaton to which 8 refers Motherboard GA MA74GMT S2H GA MA74GMT S2 is in conformity with reference to the specification under which conformity is declared in accordance with 2004 106 EC EMC Directive D EN 5011 Limits and methods of measurement EN 61000 3 2 Disturbances in supply systems caused of radio Osturbance characteristics of industrial scientific and medical ISM EN 61000 3 3 Disturbances in supply systems caused high frequency equapmen by household apphances and serdar lectrical equipment Voltage fluctuatons D EN 55013 Limits and methods of measurement O EN 55024 Infoemation Technology of mao Gsturhance characteristics of equpment Immuniy broadcast receivers aod associated characteristics Lim ts and methods of equipment measurement O EN 5014 4 Limits and methods of measurement C EN 50082 1 Generic immunity standard Part 1 of radio sturbance characteristics of Residual commercial and light industry household electrical applances portable tools and similar electrical C EN 50082 2 Generic immunity standard Part 2 apparatus Industrial enveonment
34. Lets the AMD Cool n Quiet driver dynamically adjust the CPU clock and VID to reduce heat output from your computer and its power consumption Default gt gt Disabled Disables this function Hard Disk Boot Priority Specifies the sequence of loading the operating system from the installed hard drives Use the up or down arrow key to select a hard drive then press the plus key lt gt or lt PageUp gt or the minus key lt gt or lt PageDown gt to move it up or down on the list Press lt Esc gt to exit this menu when finished lt gt First Second Third Boot Device Specifies the boot order from the available devices Use the up or down arrow key to select a device and press Enter to accept Options are Floppy LS120 Hard Disk CDROM ZIP USB FDD USB ZIP USB CDROM USB HDD Legacy LAN Disabled Password Check Specifies whether a password is required every time the system boots or only when you enter BIOS Setup After configuring this item set the password s under the Set Supervisor User Password item in the BIOS Main Menu gt gt Setup password is only required for entering the BIOS Setup program Default b gt System password is required for booting the system and for entering the BIOS Setup program D Only for GA MA74GMT S2H Note This item appears only if you install a CPU that supports this feature BIOS Setup 42 lt HDD S M A RIT Capability Enables or disables the S M A R T Self Monit
35. O EN 55015 Limits and methods of measurement O EN 55014 2 Immunity recueenments for household of radio Gsturbance characteristics of appliances tools and similar apparatus fluorescent lames and luminaries D EN 55020 Immunity from radio interterence of O EN 50091 2 EMC requirements for uninterruptible broadcast receivers and assocated power systems UPS equipment E EN 55022 Limits and methods of measurement of rito disturbance characteristics of information technology equipment D DIN VDE 0855 Cabied distribution systems Equipment D part 10 for receiving andor distribution from O part 12 Sound and television signals CE I CE marking EC conformity marking The manufacturer also declares the conformity of above mentioned product with the actual required safety standards in accordance with LVD 2006 95 EC D EN 60065 Safety roqurements for mains operated EN 60950 Safety for information technology equipment electronic and related apparatus for inciuding electrical business equipment household and siriar genera use D EN 60335 Safety of household and sima O EN 50091 1 General and Safety requirements for electncal apoharces uninterruptible power systems UPS Manufacturer lmporter suture Timmy Huang Stamp Date Jul 9 2010 Name Timmy Huang DECLARATION OF CONFORMITY Per FCC Part 2 Section 2 1077 a FC Responsible Party Name G B T INC U S A Address 17358 Railroad Street City of Industry CA 91748 Phone Fax No 818 854 9338 818
36. SB Controllers USB Legacy Function USB Storage Function Onboard Serial Port 1 Enabled Item Help RAID Menu Level gt Disabled Enabled Disabled Press Enter Enabled Enabled Enabled Enabled 3F8 IRQ4 142 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Figure 1 Step 2 Save changes and exit BIOS Setup The BIOS Setup menus described in this section may differ from the exact settings for your moth erboard The actual BIOS Setup menu options you will see shall depend on the motherboard you have and the BIOS version Appendix 72 C Configuring RAID set in RAID BIOS Enter the RAID BIOS setup utility to configure a RAID array Skip this step and proceed with the installation of Windows operating system for a non RAID configuration Step 1 After the POST memory test begins and before the operating system boot begins look for a message which says Press lt Ctrl F gt to enter FastBuild tm Utility Figure 2 Press Ctrl lt F gt to enter the RAID BIOS setup Utility RAID Option ROM Version 3 0 1540 47 c 2008 Advanced Micro Devices Inc All rights reserved No Array is defined Press lt Ctrl F gt to enter FastBuild tm Utility Figure 2 Step 2 Main Menu This is the first option screen when you enter the BIOS RAID Setup utility Figure 3 To view the disk drives
37. The system boot will not stop for a keyboard or a floppy disk drive error but it will stop for all other errors Memory These fields are read only and are determined by the BIOS POST Base Memory Also called conventional memory Typically 640 KB will be reserved for the MS DOS operating system gt Extended Memory The amount of extended memory 41 BIOS Setup 2 5 Advanced BIOS Features CMOS Setup Utility Copyright C 1984 2010 Award Software Virtualization AMD K8 C ool Quiet control Hard Disk Boot Priority First Boot Device Second Boot Device Third Boot Device Password Check HDD S M A R T Capability Away Mode Backup BIOS Image to HDD Init Display First lt Surround View Graphics Display Mode Advanced BIOS Features Disabled Item Help Auto Menu Level gt Press Enter Hard Disk CDROM Floppy Setup Disabled Disabled Disabled PCI Slot Disabled D SUB DVI Internal Graphics Mode Auto Frame Buffer Size Auto Current UMA Size 128MB Ti lt Move Enter Select F5 Previous Values PU PD Value F10 Save ESC Exit F1 General Help F6 Fail Safe Defaults F7 Optimized Defaults c Virtualization Virtualization allows a platform to run multiple operating systems and applications in independent parti tions With virtualization one computer system can function as multiple virtual systems Default Disabled AMD K8 Cool amp Quiet control gt gt Auto
38. Vista e Xpress Recovery and Xpress Recovery2 are different utilities For example a backup file created ER with Xpress Recovery cannot be restored using Xpress Recovery2 e USB hard drives are not supported e Hard drives in RAID AHCI mode are not supported Installation and Configuration Turn on your system to boot from the Windows Vista setup disk A Installing Windows Vista and Partitioning the Hard Drive Step 1 Step 2 Click Drive options Click New Note Xpress Recovery2 checks the first physical hard drive in the following sequence The first PATA IDE connector the second PATA IDE connector the first SATA connector the second SATA connector and so forth For example when hard drives are attached to the first IDE and the first SATA connectors the hard drive on the first IDE connector is the first physical drive When hard drives are attached to the first and second SATA connectors the hard drive on the first SATA connector is the first physical drive 59 Unique Features Step 3 Step 4 When partitioning your hard drive make sure to After the operating system is installed right click leave unallocated space 10 GB or more is recom the Computer icon on your desktop and select mended actual size requirements vary depending Manage Go to Disk Management to check disk on the amount of data and begin the installation of allocation the operating system rr Steps EE pe BES see Xpress Recover
39. ad Fail Safe Defaults Y N N PC Health Status ESC Quit T7 Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Load Fail Safe Defaults Press Enter on this item and then press the Y key to load the safest BIOS default settings In case system instability occurs you may try to load Fail Safe defaults which are the safest and most stable BIOS settings for the motherboard 2 11 Load Optimized Defaults CMOS Setup Utility Copyright C 1984 2010 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Peripherals Set User Password Power Manageme o PnP PCI Configur Load Optimized Defaults Y N N PC Health Status ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Load Optimized Defaults Press lt Enter gt on this item and then press the lt Y gt key to load the optimal BIOS default settings The BIOS defaults settings help the system to operate in optimum state Always load the Optimized defaults after updating the BIOS or after clearing the CMOS values BIOS Setup 52 2 12 Set Supervisor User Password CMOS Setup Utility Copyright C 1984 2010 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults
40. allation you can pro ceed with the Windows XP installation 79 Appendix B Installing Windows Vista The procedure below assumes that only one RAID array exists in your system Step 1 Restart your system to boot from the Windows Vista setup disk and perform standard OS installation steps When a screen similar to that below appears RAID hard drive will not be detected at this stage select Load Driver Figure 3 el See Free Space Type Figure 3 Step 2 Insert the motherboard driver disk Method A or the removable storage device such as USB flash drive that contains the SATA RAID AHCI driver Method B then specify the location of the driver Figure 4 Note For users using a SATA optical drive be sure to copy the driver files from the motherboard driver disk to a USB flash drive before installing Windows Vista go to the BootDrv folder and save the whole SBxxxV folder to the USB flash drive Then use Method B to load the driver Method A Insert the motherboard driver disk into your system and browse to the following directory BootDrv SBxxxV LH For Windows Vista 64 bit browse to the LH64A folder Method B Insert the USB flash drive containing the driver files and browse to the LH for Windows Vista 32 bit or LH64A for Windows Vista 64 bit folder Figure 4 Appendix 80 Step 3 When a screen as shown in Figure 5 appears select AMD AHCI Compatible RAID Controller and press N
41. an header CPU FAN on the motherboard CPU cooler and CPU may adhere to the CPU Inadequately removing the CPU cooler may damage ER cn extreme care when removing the CPU cooler because the thermal grease tape between the the CPU Hardware Installation 1 4 Installing the Memory Read the following guidelines before you begin to install the memory e Make sure that the motherboard supports the memory It is recommended that memory of the same capacity brand speed and chips be used Go to GIGABYTE s website for the latest supported memory speeds and memory modules Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage e Memory modules have a foolproof design A memory module can be installed in only one direc tion If you are unable to insert the memory switch the direction 1 4 1 Dual Channel Memory Configuration This motherboard provides two DDR3 memory sockets and supports Dual Channel Technology After the memory is installed the BIOS will automatically detect the specifications and capacity of the memory En abling Dual Channel memory mode will double the original memory bandwidth The two DDR3 memory sockets are divided into two channels and each channel has one memory socket as following gt Channel 0 DDR3 1 gt Channel 1 DDR3 2
42. at is unable to start 3 Donot use the G O M GIGABYTE Online Management function when using BIOS 4 GIGABYTE product warranty does not cover any BIOS damage or system failure resulting from an inad equate BIOS flashing B Using BIOS eios le eee anG Flash Memory Size po Update BIOS from File I BIOS Sign on Message annee BIOS Vendor tm m9 KA Load CMOS detautt atter BIOS update fg ciear omi data Pool 1 Update the BIOS Using the Internet Update Function Click Update BIOS from GIGABYTE Server select the BIOS server site closest to your location and then download the BIOS file that matches your motherboard model Follow the on screen instructions to complete If the BIOS update file for your motherboard is not present on the BIOS server site please CA download the BIOS update file from GIGABYTE s website and follow the instructions in Update the BIOS without Using the Internet Update Function below 2 Update the BIOS without Using the Internet Update Function Click Update BIOS from File then select the location where you save the BIOS update file obtained from the Internet or through other source Follow the on screen instructions to complete 3 Save the Current BIOS File Click Save Current BIOS to File to save the current BIOS file 4 Lee cmos detaut atter Bios update Load BIOS Defaults after BIOS Update Select the Load CMOS default after BIOS update check box and then the system will automatically
43. atures essent 40 2 5 Advanced BIOS Features cccccsssesssscssssssessesssessessessessesssesesasseesaseseess 42 26 integrated Peripherals AA AA 44 2 7 Power Management Setup 47 2 8 PnP PCI Configurations cono tete rn Fahne ku eet reb Re Rete Kan 49 2 9 PCA Status sa tm otn RI er itu ERE UR ERE oru mate 50 2 10 Load Fail Safe Defaults aaa 52 2 11 Load Optimized Defaults aman 02 2 12 Set Supervisor User Password aaa 59 2 19 Save amp Exif Setup ioris BANGAG AA UP FEDES SUO INFE nee 54 2 14 Exit Without Saying mamamana maana nman 54 Chapter 3 Drivers Installation 55 3 1 Installing Chipset Drivers aman 55 3 2 Application SONWANE suc ctae KANA UU tre ANAN a 56 d3 Technical WAIN ANS RTT 56 S BECCA AA 57 UE Cl CR r iiini 57 SOMMER oi PRU 58 NIN a KN 58 Chapter 4 Unique FealuleS i eec aaa 59 d l Xpress RECOV La PA 99 4 2 BIOS Update DIIS iius ti EEUU Dt EUH QUU aO Eae IUE 62 4 2 1 Updating the BIOS with the Q Flash Utility 62 4 2 2 Updating the BIOS with the BIOS Utility 65 2 9 CE Ud sd inu tus 66 2 RES PB 67 4 b SMART RECOVERY aman ttr rr etos cen ix eai i rtt 68 BRUNO GI RR 69 CRD OE OE 71 5 1 Configuring SATA Hard Drive s eese nnns 71 5 1 1 Configuring the Onboard SATA Controller 71 5 1 2 Making a SATA RAID AHCI Driver Diskette
44. ays disables the onboard graphics whether or not a PCI Express card is installed gt gt Auto Outputs from the onboard graphics if no PCI Express graphics card is installed Always outputs from the PCI Express graphics card when a PCI Express graphics card is installed Default lt Frame Buffer Size Frame buffer size is the total amount of system memory allocated solely for the onboard graphics con troller MS DOS for example will use only this memory for display Options are Auto default 64MB 128MB 256MB 512MB lt Current Buffer Size When Frame Buffer Size is set to Auto this item will show the system memory size automatically allocated for the onboard graphics controller If you manuanlly change the Frame Buffer Size this item will show the memory size you set D Only for GA MA74GMT S2H Note This item appears only if you install a CPU that supports this feature 43 BIOS Setup 2 6 Integrated Peripherals CMOS Setup Utility Copyright C 1984 2010 Award Software Integrated Peripherals OnChip SATA Controller OnChip SATA Type Green LAN Onboard LAN Function Onboard LAN Boot ROM SMART LAN Onboard Audio Function USB Controllers USB Legacy Function USB Storage Function Enabled Item Help Native IDE Menu Level gt Disabled Enabled Disabled Press Enter Enabled Enabled Enabled Enabled Onboard Serial Port 1 3F8 IRQ4 Ne Move Enter Select PU PD Value F10 Save ESC Exi
45. contained in all homogenous materiale of this part is below the limit requirement SJ T 11363 2006 X Gon RUE ET TORRE PS m LHSU TIET363 2006 ERE eX Indicates that this hazardous substance contained in at least one of the homogenous materials of this part ig above the limit requirement in SJ T 11363 2006 HMMM RRP RBH AE RRS EX miam BES Ha ERS A ATA Re This table shows where these substances may be found in the supply chain of our electronic information products as of the date of the sale of the enclosed products Note that some of the component types listed above may or may not be a part of the enclosed product 95 Appendix Appendix 96 97 Appendix Appendix 98 Contact Us e GIGA BYTE TECHNOLOGY CO LTD Address No 6 Bau Chiang Road Hsin Tien Taipei 231 Taiwan TEL 886 2 8912 4000 FAX 886 2 8912 4003 Tech and Non Tech Support Sales Marketing http ggts gigabyte com tw WEB address English http www gigabyte com WEB address Chinese http www gigabyte tw e G B T INC U S A TEL 1 626 854 9338 FAX 1 626 854 9339 Tech Support http rma gigabyte us Web address http www gigabyte us e G B T INC USA Mexico Tel 1 626 854 9338 x 215 Soporte de habla hispano
46. d Blu ray Discs Hardware Installation In order to get better playback quality when playing the HD DVD or Blu ray discs refer to the recom mended system requirements or better below e CPU AMD Phenom X3 processor or above e Memory Two 1 GB DDR3 1066 MHz memory modules with dual channel mode enabled BIOS Setup At least 256 MB of UMA Frame Buffer Size refer to Chapter 2 BIOS Setup Advanced BIOS Features for more information e Playback software CyberLink PowerDVD 8 0 or later e HDCP compliant monitor s RJ 45 LAN Port The Gigabit Ethernet LAN port provides Internet connection at up to 1 Gbps data rate The following de scribes the states of the LAN port LEDs Connection Speed LED Activity LED Connection Speed LED Activity LED State Description State Description Ez T Orange 1 Gbps data rate Blinking Data transmission or receiving is occurring Green 100 Mbps data rate Off No data transmission or receiving is occurring LAN Port Off 10 Mbps data rate Line In Jack Blue The default line in jack Use this audio jack for line in devices such as an optical drive walkman etc Line Out Jack Front Speaker Out Green The default line out jack Use this audio jack for a headphone or 2 channel speaker This jack can be used to connect front speakers in a 4 5 1 channel audio configuration Mic In Jack Pink The default Mic in jack Microphones must be connected to this jack
47. d is HDCP compliant Connect the HDMI audio video device to this port The HDMI Technology can support a maximum resolution of 1920x1080p but the actual resolutions supported depend on the monitor being used After installing the HDMI device make sure the default device for sound playback is the HDMI ER device The item name may differ from operating system Refer to the figures below for details and enter BIOS Setup then set Graphics Display Mode to D SUB HDMI under Advanced BIOS Features Please note the HDMI audio output only supports AC3 DTS and 2 channel LPCM formats AC3 and DTS require the use of an external decoder for decoding amp Sound a In Windows Vista select Start gt Control Panel gt Sound PP cm sana select Realtek HDMI Output and then click Set Default Select a playback device below to modify its settings Speakers 3 Rentet Dogital Output Realtek HOMI Output Note 1 The DVI D port does not support D Sub connection by adapter Note 2 Simultaneous output for DVI D and HDMI is not supported D Only for GA MA74GMT S2H 19 Hardware Installation A Dual Display Configurations This motherboard provides three ports for video output DVI D HDMI and D Sub The table below shows the supported dual display configurations Dual Combination Supported or Not Display DVI D D Sub Yes DVI D HDMI No HDMI D Sub Yes B Playback of HD DVD an
48. dio driver successfully For Windows XP only Step 1 First make sure Service Pack 1 or Service Pack 2 has been installed check in My Computer gt Properties gt Gen eral gt System If not please update it from Microsoft s website Then make sure the Microsoft UAA Bus Driver for High Definition Audio has been installed successfully check in My Computer gt Properties gt Hardware gt Device Manager gt System Devices Step 2 Check if Audio Device on High Definition Audio Bus or Unknown device is present in Device Manager or Sound video and game controllers If yes please disable this device If not skip this step Step 3 Then go back to My Computer gt Properties gt Hardware gt Device Manager gt System devices and right click on Microsoft UAA Bus Driver for High Definition Audio and select Disable and Uninstall Step 4 In Device Manager right click on the computer name and select Scan for hardware changes When the Add New Hardware Wizard appears click Cancel Then install the onboard HD audio driver from the motherboard driver disk or download the audio driver from GIGABYTE s website to install For more details go to the Support amp Downloads Motherboards FAQ page on our website and search for onboard HD audio driver What do the beeps emitted during the POST mean The following Award BIOS beep code descriptions may help you identify possible computer problems For reference only 1 short System boot
49. do not use internationally banned toxic chemicals Waste Electrical amp Electronic Equipment WEEE Directive Statement GIGABYTE will fulfill the national laws as interpreted from the 2002 96 EC WEEE Waste Electrical and Elec tronic Equipment directive The WEEE Directive specifies the treatment collection recycling and disposal of electric and electronic devices and their components Under the Directive used equipment must be marked collected separately and disposed of properly WEEE Symbol Statement The symbol shown below is on the product or on its packaging which indicates that this product must not be disposed of with other waste Instead the device should be taken to the waste collection centers for activation of the treatment collection recycling and disposal procedure The separate collection and recycling of your waste equipment at the time of disposal will help to conserve natural resources and ensure that it is recycled in a manner that protects human health and the environment For more information about where you can drop off your waste equipment for recycling please contact your local government office your household waste disposal service or where you purchased the product for details of environmentally safe recycling When your electrical or electronic equipment is no longer useful to you take it back to your local or regional waste collection administration for recycling f you need further assis
50. down arrow key to select Update BIOS from Drive and press lt Enter gt The Save Main BIOS to Drive option allows you to save the current BIOS file A Q Flash only supports USB flash drive or hard drives using FAT 32 16 12 file system e Ifthe BIOS update file is saved to a hard drive in RAID AHCI mode or a hard drive attached to an independent IDE SATA controller use the End key during the POST to access Q Flash 2 Select Floppy A and press Enter Q Flash Utility v2 15 Flash TV GG S126 asa makaaasa ansabe SST 25VF080B IM 0 file s found 3 Select the BIOS update file and press Enter A Make sure the BIOS update file matches your motherboard model Step 2 The process of the system reading the BIOS file from the floppy disk is displayed on the screen When the message Are you sure to update BIOS appears press lt Enter gt to begin the BIOS update The monitor will display the update process e Donot turn off or restart the system when the system is reading updating the BIOS e Do not remove the floppy disk USB flash drive or hard drive when the system is updat ing the BIOS Step 3 When the update process is complete press any key to return to the main menu Q Flash Utility v2 15 SST 25VF080B 63 Unique Features Step 4 Press lt Esc gt and then lt Enter gt to exit Q Flash and reboot the system As the system boots you should see the new BIOS version is present on t
51. drive The types of floppy disk drives supported are 360 KB 720 KB 1 2 MB 1 44 MB and 2 88 MB Before connecting a floppy disk drive be sure to locate pin 1 of the connector and the floppy disk drive cable The pin 1 of the cable is typically designated by a stripe of different color For purchasing the optional floppy disk drive cable please contact the local dealer az E m Hardware Installation 6 IDE IDE Connector The IDE connector supports up to two IDE devices such as hard drives and optical drives Before attach ing the IDE cable locate the foolproof groove on the connector If you wish to connect two IDE devices remember to set the jumpers and the cabling according to the role of the IDE devices for example master or slave For information about configuring master slave settings for the IDE devices read the instructions from the device manufacturers Ed
52. e 2 Save allows you to save the current settings to a new profile txt file Load allows you to load previous settings from a profile After making changes in Easy mode Advanced mode be sure to click Set for these changes to take effect or click Default to restore to default values lt P Graphics The Graphics tab allows you to change the core clock and memory clock for your ATI or NVIDIA graphics card B smart The Smart tab allows you to specify a Smart Fan mode Smart Fan allows the CPU fan speed to be changed linearly based on the CPU temperature thresholds you set Bann Monitor The HW Monitor tab allows you to monitor hardware temperature voltage and fan speed and set temperature fan speed alarm You can choose the alert sound from the buzzer or use your own sound file wav file Note 1 Restart the computer after enabling Core Boost for the settings to take effect Note 2 The number of CPU cores that can be enabled disabled depends on the CPU being used not configurable or the function is not supported Incorrectly doing overclock overvoltage may result in damage to the hardware components such as CPU chipset and memory and reduce the useful life of these components Before you do the overclock overvoltage make sure ER Available functions in EasyTune 6 may differ by motherboard model Grayed out area s indicates that the item is A that you fully know each function of EasyTune 6 or system instab
53. e space will be freed up F Exiting Xpress Recovery2 re GIGABYTE TECH KH OLO GY Select REBOOT to exit Xpress Recovery2 61 Unique Features 4 2 BIOS Update Utilities GIGABYTE motherboards provide two unique BIOS update tools Q Flash and BIOS GIGABYTE Q Flash and BIOS are easy to use and allow you to update the BIOS without the need to enter MS DOS mode Additionally this motherboard features the DualBIOS design which enhances protection for the safety and stability of your computer by adding one more physical BIOS chip What is DualBIOS Led Motherboards that support DualBIOS have two BIOS onboard a main BIOS and a backup BIOS Normally the system works on the main BIOS However if the main BIOS is corrupted or damaged the backup BIOS will take over on the next system boot and copy the BIOS file to the main BIOS to ensure normal system operation For the sake of system safety users cannot update the backup BIOS manually What is Q Flash een With Q Flash you can update the system BIOS without having to enter operating ENS systems like MS DOS or Window first Embedded in the BIOS the Q Flash tool frees you from the hassles of going through complicated BIOS flashing process What is QBIOS EIOS BIOS allows you to update the system BIOS while in the Windows environ ment BIOS will download the latest BIOS file from the nearest BIOS server site and update the BIOS 4 2 41 Updat
54. ed on the operating system to be installed Refer to the following table for the SATA driver directories for different Windows operating systems Operating System Directory Windows XP 32 bit Bootdrv S Bxxx x86 Windows XP 64 bit Bootdrv SBxxx x64 Windows Vista 32 bit AHCI mode Bootdrv SBxxxV AHCI LHx86 Bootdrv SBxxxV RAID LH Windows Vista 64 bit AHCI mode Windows Vista 64 bit RAID mode Windows 7 32 bit AHCI mode Bootdrv SBxxxW7 AHCI Win7x86 Windows 7 32 bit RAID mode Bootdrv SBxxxW7 RAID W7 Windows 7 64 bit AHCI mode Bootdrv SBxxxW7 AHCI Win7x64 Windows 7 64 bit RAID mode Bootdrv SBxxxW7 RAID W764A Bootdrv SBxxxV AHCI LHx64 Bootdrv SBxxxV RAID LH64A Windows Vista 32 bit RAID mode fT Appendix In Windows mode Steps 1 Use an alternative system and insert the motherboard driver disk 2 From your optical drive folder double click the Menu exe file in the BootDrv folder Figure 2 Command Prompt window will open similar to that in Figure 3 3 Insert the blank formatted disk Select the controller driver by pressing the corresponding letter from the menu and press lt Enter gt For example from the menu in Figure 3 to install Windows XP to the RAID AHCI hard drives select 3 ATi AHCI RAID Driver for XP Your system will then automatically copy the driver files to the floppy disk Press any key to exit when finished Figure 3
55. ement Setup Use this menu to configure all the power saving functions PnP PCI Configurations Use this menu to configure the system s PCI amp PnP resources PC Health Status Use this menu to see information about autodetected system CPU temperature system voltage and fan speed etc Load Fail Safe Defaults Fail Safe defaults are factory settings for the most stable minimal performance system operations Load Optimized Defaults Optimized defaults are factory settings for optimal performance system operations Set Supervisor Password Change set or disable password It allows you to restrict access to the system and BIOS Setup A supervisor password allows you to make changes in BIOS Setup Set User Password Change set or disable password It allows you to restrict access to the system and BIOS Setup A user password only allows you to view the BIOS settings but not to make changes Save amp Exit Setup Save all the changes made in the BIOS Setup program to the CMOS and exit BIOS Setup Pressing lt F10 gt can also carry out this task Exit Without Saving Abandon all changes and the previous settings remain in effect Pressing Y to the confirmation mes sage will exit BIOS Setup Pressing lt Esc gt can also carry out this task BIOS Setup 34 2 3 MB Intelligent Tweaker M I T CMOS Setup Utility Copyright C 1984 2010 Award Software MB Intelligent Tweaker M I T gt Advanced Clock Calibration N Pre
56. ent on the CPU being used Note This item appears only if you install a CPU that supports this feature BIOS Setup 36 CPU Host Clock Control Enables or disables the control of CPU host clock Auto default allows the BIOS to automatically adjust the CPU host frequency Manual allows the CPU Frequency MHz item below to be configurable Note If your system fails to boot after overclocking please wait for 20 seconds to allow for automated system reboot or clear the CMOS values to reset the board to default values c CPU Frequency MHz Allows you to manually set the CPU host frequency The adjustable range is from 200 MHz to 500 MHz Im portant It is highly recommended that the CPU frequency be set in accordance with the CPU specifications lt PCIE Clock MHz Allows you to manually set the PCle clock frequency The adjustable range is from 100 MHz to 150 MHz Auto sets the PCle clock frequency to standard 100 MHz Default Auto VGA Core Clock MHz Allows you to manually set the VGA Core clock The adjustable range is from 200 MHz to 600 MHz lt Set Memory Clock Determines whether to manually set the memory clock Auto lets BIOS automatically set the memory clock as required Manual allows the memory clock control item below to be configurable Default Auto Memory Clock This option is configurable only when Set Memory Clock is set to Manual gt gt X4 00 Sets Memory Clock to X4 00 b gt X5 33 Sets Memory Clock to X5 33 b
57. enu use the up arrow key lt T gt or the down arrow key lt J gt to select the first boot device then press Enter to accept Function Keys To exit Boot Menu press lt Esc gt The system will directly boot from the device configured in Boot Menu Note The setting in Boot Menu is effective for one time only After system restart the device boot order will still be based on BIOS Setup settings You can access Boot Menu again to change the first boot de vice setting as needed lt END gt Q FLASH Press the lt End gt key to access the Q Flash utility directly without having to enter BIOS Setup first BIOS Setup 32 2 2 The Main Menu Once you enter the BIOS Setup program the Main Menu as shown below appears on the screen Use ar row keys to move among the items and press lt Enter gt to accept or enter a sub menu Sample BIOS Version GA MA74GMT S2 F7g CMOS Setup Utility Copyright C 1984 2010 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Peripherals Set User Password Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Status ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Change CPU s Clock amp Voltage BIOS Setup Program Function Keys lt T gt lt gt
58. er and operating system m UQOUscgp z Before you begin Please prepare At least two SATA hard drives to ensure optimal performance it is recommended that you use two hard drives with identical model and capacity If you do not want to create RAID you may prepare only one hard drive An empty formatted floppy disk e Windows Vista XP setup disk Motherboard driver disk 5 1 1 Configuring the Onboard SATA Controller A Installing SATA hard drive s in your computer Attach one end of the SATA signal cable to the rear of the SATA hard drive and the other end to available SATA port on the motherboard Then connect the power connector from your power supply to the hard drive Note 1 Skip this step if you do not want to create RAID array on the SATA controller Note 2 Required when the SATA controller is set to AHCI or RAID mode 71 Appendix B Configuring SATA controller mode in BIOS Setup Make sure to configure the SATA controller mode correctly in system BIOS Setup Step 1 Turn on your computer and press Delete to enter BIOS Setup during the POST Power On Self Test Un der Integrated Peripherals make sure OnChip SATA Controller is enabled To enable RAID set OnChip SATA Type to RAID CMOS Setup Utility Copyright C 1984 2010 Award Software Integrated Peripherals OnChip SATA Controller OnChip SATA Type Green LAN Onboard LAN Function Onboard LAN Boot ROM SMART LAN Onboard Audio Function U
59. er will make the device unable to work or even damage it a For HD Front Panel Audio For AC 97 Front Panel Audio Pin No Definition Pin No Definition L 1 MIC2_L 1 MIC 2 GND 2 GND 3 MIC2 R 3 MIC Power 4 ACZ_DET 4 NC E MM 5 LINE2 R 5 Line Out R I j 6 GND 6 NC U 7 oa 7 NC B 8 No Pin 8 No Pin 9 LINE2 L 9 Line Out L 10 GND 10 NC front panel audio module refer to the instructions on how to activate AC 97 functionality via the audio software in Chapter 5 Configuring 2 4 5 1 7 1 Channel Audio Audio signals will be present on both of the front and back panel audio connections simultane ously If you want to mute the back panel audio only supported when using an HD front panel audio module refer to Chapter 5 Configuring 2 4 5 1 7 1 Channel Audio e Some chassis provide a front panel audio module that has separated connectors on each wire instead of a single plug For information about connecting the front panel audio module that has different wire assignments please contact the chassis manufacturer GA The front panel audio
60. ess http ww gigabyte ru GIGABYTE TECHNOLOGY FRANCE France Poland WEB address http www gigabyte fr WEB address http www gigabyte pl e Sweden Ukraine WEB address http www gigabyte se WEB address http ww gigabyte ua e Italy e Romania WEB address http www giga byte it WEB address http www gigabyte com ro e Spain e Serbia WEB address http www giga byte es WEB address http ww gigabyte co rs Greece e Kazakhstan WEB address http www gigabyte com gr WEB address http www gigabyte kz Czech Republic WEB address http www gigabyte cz You may go to the GIGABYTE website select your language in the language list on the top right corner of the website e GIGABYTE Global Service System GIGABYTE Welcome to GIGABYTE Service system If you want to submit new question OF check oor response please enter your I Mail address and press the buton to loy in Eto tro sn Appendix To submit a technical or non technical Sales Market ing question please link to http ggts gigabyte com tw Then select your language to enter the system 100
61. ext Select the driver 16 be inatabed gem Bm Figure 5 Step 4 After the driver is loaded the RAID drive will appear Select the RAID drive and then press Next to continue the OS installation Figure 6 Figure 6 ER The install menus described in this chapter are for reference only and may differ by driver version 81 Appendix Rebuilding an Array Rebuilding is the process of restoring data to a hard drive from other drives in the array Rebuilding applies only to fault tolerant arrays such as RAID 1 or RAID 10 arrays To replace the old drive make sure to use a new drive of equal or greater capacity The procedures below assume a new drive is added to replace a failed drive to rebuild a RAID 1 array While in the operating system make sure the chipset drivers and ATi RAID Utility have been installed from the motherboard driver disk Then launch the AMD RAIDXpert from All Programs in the Start Menu Step 1 Step 2 Enter the login ID and password default admin Select the RAID array to be rebuilt under Logical and then click Sign in to launch AMD RAIDXpert Drive View and click the Rebuild tab in the Logi cal Drive Information pane pan 4 PM Step 3 Step 4 Select one available drive and click Start Now to The rebuilding progress is displayed on the start the rebuilding process screen and you can select Pause Resume Abort Restart during the rebuild
62. for AM3 processors AMD Phenom II processor AMD Athlon I processor Go to GIGABYTE s website for the latest CPU support list 2000 MT s Chipset North Bridge AMD 740G South Bridge AMD SB710 2 x 1 5V DDR3 DIMM sockets supporting up to 8 GB of system memory Dual channel memory architecture Support for DDR3 1333 O C 1066 800 MHz memory modules Support for non ECC memory modules Go to GIGABYTE s website for the latest supported memory speeds and memory modules Integrated in the North Bridge p Onboard Graphics 1 x D Sub port A 1 X DVI D port Note 2 Note 3 1 x HDMI port e Audio Realtek ALC888B codec High Definition Audio 2 4 5 1 7 1 channel Support for S PDIF Out Support for S PDIF In Support for CD In LAN 1 x Realtek RTL 8111D E chip 10 100 1000 Mbit Expansion Slots 1 x PCI Express x16 slot running at x16 1 x PCI Express x1 slot 2 x PCI slots Storage Interface South Bridge 1xIDE connector supporting ATA 133 100 66 33 and up to 2 IDE devices 4xSATA 3Gb s connectors supporting up to 4 SATA 3Gb s devices Support for SATA RAID 0 RAID 1 RAID 10 and JBOD ITE IT8718 chip 1x floppy disk drive connector supporting up to 1 floppy disk drive KO USB South Bridge Up to 12 USB 2 0 1 1 ports 8 on the back panel 4 via the USB brackets connected to the internal USB headers D Only for GA M
63. ft place your fin gers on the top edge of the memory push down on the memory and insert it vertically into the memory socket Step 2 The clips at both ends of the socket will snap into place when the memory module is securely inserted 17 Hardware Installation 1 5 Installing an Expansion Card Read the following guidelines before you begin to install an expansion card A e Make sure the motherboard supports the expansion card Carefully read the manual that came with your expansion card e Always turn off the computer and unplug the power cord from the power outlet before installing an expansion card to prevent hardware damage PCI Express x1 Slot Fm PCI Express x16 Slot a mut PCI Slot Follow the steps below to correctly install your expansion card in the expansion slot Locate an expansion slot that supports your card Remove the metal slot cover from the chassis back panel Align the card with the slot and press down on the card until it is fully seated in the slot Make sure the metal contacts on the card are completely inserted into the slot Secure the card s metal bracket to the chassis back panel with a screw After installing all expansion cards replace the chassis cover s Turn on your computer If necessary go
64. g Options are Auto default 1T 2T c TwTr Command Delay Options are Auto default 4T 7T o Trfc0 for DIMM1 Options are Auto default 90ns 110ns 330ns 350ns o Trfc2 for DIMM2 Options are Auto default 90ns 110ns 330ns 350ns lt gt Write Recovery Time Options are Auto default 5T 12T c Precharge Time Options are Auto default 4T 7T Row Cycle Time Options are Auto default 11T 42T lt gt RAS to RAS Delay Options are Auto default 4T 7T c CKE Power Down Mode Enables or disables the CKE Power Down Mode Default Disabled Note This item appears only if you install a CPU that supports this feature BIOS Setup 98 serene System Voltage Optimized System Voltage Control Determines whether to manually set the system voltages Auto lets the BIOS automatically set the system voltages as required Manual allows all voltage control items below to be configurable Default Manual lt gt DDR3 Voltage Control Allows you to set memory voltage gt gt Normal Supplies the memory voltage as required Default gt gt 0 050V 0 750V The adjustable range is from 0 050V to 0 750V Note Increasing memory voltage may result in damage to the memory o NorthBridge Volt Control Allows you to set the North Bridge voltage bp Normal Supplies the North Bridge voltage as required Default b gt 0 1V 0 3V The adjustable range is from 0 1V to 0 3V c SouthBridge Volt Control Allows you
65. gt X6 66 Sets Memory Clock to X6 66 b gt X8 00 Sets Memory Clock to X8 00 DRAM Configuration CMOS Setup Utility Copyright C 1984 2010 Award Software DRAM Configuration DCTs Mode Vote Unganged Item Help DDR3 Timing Items Auto Menu Level gt gt CAS latency Auto RAS to CAS R W Delay Auto Row Precharge Time Auto Minimum RAS Active Time Auto 1T 2T Command Timing Auto TwTr Command Delay Auto Trfc0 for DIMMI Auto Trfc2 for DIMM2 Auto Write Recovery Time Auto Precharge Time Auto Row Cycle Time Auto RAS to RAS Delay Auto CKE Power Down Mode Disabled X X X X X X X X X X X X 112 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Note This item appears only if you install a CPU that supports this feature 37 BIOS Setup c DCTs Mode Allows you to set memory control mode gt gt Ganged Sets memory control mode to single dual channel bp Unganged Sets memory control mode to two single channel Default lt gt DDR3 Timing Items Manual allows all DDR3 Timing items below to be configurable Options are Auto default Manual gt CAS latency Options are Auto default 4T 12T lt RAS to CAS R W Delay Options are Auto default 5T 12T Row Precharge Time Options are Auto default 5T 12T lt Minimum RAS Active Time Options are Auto default 15T 30T lt 1T 2T Command Timin
66. hasing the optional USB bracket please contact the local dealer Pin No Definition Power 5V Power 5V USB DX USB DY USB DX USB DY GND GND No Pin NC Oo oo BR n5 a ce Donot plug the IEEE 1394 bracket 2x5 pin cable into the USB header A Prior to installing the USB bracket be sure to turn off your computer and unplug the power cord from the power outlet to prevent damage to the USB bracket 27 Hardware Installation 13 COM Serial Port Header The COM header can provide one serial port via an optional COM port cable For purchasing the op tional COM port cable please contact the local dealer Pin No Definition NDCD NSIN NSOUT NDTR GND NDSR NRTS NCTS NRI No Pin Oo BR RN
67. he POST screen Step 5 During the POST press lt Delete gt to enter BIOS Setup Select Load Optimized Defaults and press lt Enter gt to load BIOS defaults System will re detect all peripheral devices after a BIOS update so we recommend that you reload BIOS defaults CMOS Setup Utility Copyright C 1984 2010 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS Features Load Optimized Defaults Advanced BIOS Features Set Supervisor Password Integrated Peripherals Set User Password Power Manageme 9 PnP PCI Configur Load Optimized Defaults Y N Y PC Health Status ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Load Optimized Defaults Press lt Y gt to load BIOS defaults Step 6 Select Save 4 Exit Setup and then press Y to save settings to CMOS and exit BIOS Setup The proce dure is complete after the system restarts Unique Features 64 4 2 2 Updating the BIOS with the BIOS Utility A Before You Begin 1 In Windows close all applications and TSR Terminate and Stay Resident programs This helps prevent unexpected failures when performing a BIOS update 2 During the BIOS update process ensure the Internet connection is stable and do NOT interrupt the Internet connection for example avoid a power loss or switching off the Internet Failure to do so may result in a corrupted BIOS or a system th
68. header supports HD audio by default If your chassis provides an AC 97 10 CD IN CD In Connector You may connect the audio cable that came with your optical drive to the header Pin No Definition CD L GND GND CD R GH BIDIN CR a BS az Hardware Installation 26 11 SPDIF IO S PDIF In Out Header This header supports digital S PDIF In Out Via an optional S PDIF In and Out cable this header can connect to an audio device that supports digital audio out and an audio system that supports digital au dio in For purchasing the optional S PDIF In and Out cable please contact the local dealer o Pin No Definition 6 5 1 Power Il 2 J1 2 No Pin 3 SPDIF 4 SPDIFI 5 GND nn 6 GND C3 ry e 12 F USB1 F USB2 USB Headers The headers conform to USB 2 0 1 1 specification Each USB header can provide two USB ports via an optional USB bracket For purc
69. icating the password has been can celled 53 BIOS Setup 2 13 Save amp Exit Setup CMOS Setup Utility Copyright C 1984 2010 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS I tults Advanced BIOS I Save to CMOS and EXIT Y N Y ord Integrated Periphe Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Status ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Save Data to CMOS Press lt Enter gt on this item and press the lt Y gt key This saves the changes to the CMOS and exits the BIOS Setup program Press lt N gt or lt Esc gt to return to the BIOS Setup Main Menu 2 14 Exit Without Saving CMOS Setup Utility Copyright C 1984 2010 Award Software MB Intelligent Tweaker M I T Load Fail Safe Defaults Standard CMOS I tults Advanced BIOS F Quit Without Saving Y N N ord Integrated Periphe Power Management Setup Save amp Exit Setup PnP PCI Configurations Exit Without Saving PC Health Status ESC Quit TL Select Item F11 Save CMOS to BIOS F8 Q Flash F10 Save amp Exit Setup F12 Load CMOS from BIOS Abandon all Data Press Enter on this item and press the Y key This exits the BIOS Setup without saving the changes made in BIOS Setup to the CMOS Press lt N gt or Esc to return to the BIOS Setup Main Menu BIOS Setup 54
70. ility or other unexpected results may occur Unique Features 66 4 4 Q Share Q Share is an easy and convenient data sharing tool After configuring your LAN connection settings and Q Share you are able to share your data with computers on the same network making full use of Internet resources GIGABYTE Ge Q Share Ver 1 0 Directions for using Q Share After installing Q Share from the motherboard driver disk go to Start gt All Programs gt GIGABYTE gt Q Share exe to launch the Q Share tool Find the Q Share icon sa in the notification area and right click on this icon to configure the data sharing settings Connect s Enable Incoming Folder Diable Incoming Folder Incoming folder F a atan COSMET au Exil Figure 1 Data Sharing Disabled Figure 2 Data Sharing Enabled Options Descriptions Option Description Connect Displays the computers with data sharing enabled Enable Incoming Folder Enables data sharing Disable Incoming Folder Disables data sharing Open Incoming Folder Accesses the shared data folder CAQ ShareFolder Change Incoming Folder Changes the data folder to be shared 9 CAQ ShareFolder Update Q Share Updates Q Share online About Q Share Displays the current Q Share version Exit Exits Q Share Note This option is available only when data sharing is NOT enabled 67 Unique Features 4 5 SMART Recovery With SMART Recovery
71. ing Speakers The following instructions use Windows Vista as the example operating system Step 1 After installing the audio driver the HD Audio Manager icon Bil will appear in the notification area Double click the icon to access the HD Audio Manager yor ee CM3 5 45 PM Note 2 4 5 1 7 1 Channel Audio Configurations Refer to the following for multi channel speaker configurations e 2 channel audio Headphone or Line out e 4 channel audio Front speaker out and Rear speaker out e 5 1 channel audio Front speaker out Rear speaker out and Center Subwoofer speaker out e 7 1 channel audio Front speaker out Rear speaker out Center Subwoofer speaker out and Side speaker out Please refer to the configurations on next page 83 Appendix The pictures to the right show the 7 1 channel speaker 7 1 Channel Speakers configurations Front Speaker Out Rear Speaker Out Center Sub woofer Speaker Out Side Speaker Out Step 2 Connect an audio device to an audio jack The The cur rent connected device is dialog box appears Select the device according to the type of device you connect Then click OK a CMS ASS a D OC dm omar gd c La Step 3 On the Speakers screen click the Speaker Configura tion tab In the Speaker Configuration list select Stereo Quadraphonic 5 1 Speaker or 7 1 Speaker according to the type of speaker configuration you wish to set up Then the speaker setup is c
72. ing process Step 5 When done the array s status on the Information page in the Logical Drive Information pane will display as Functional Appendix 82 5 2 Configuring Audio Input and Output 5 2 1 Configuring 2 4 5 1 7 1 Channel Audio The motherboard provides three audio jacks on the back panel Xi which support 2 4 5 1 7 1 9 channel audio The picture to the e lis right shows the default audio jack assignments Ens fn va The integrated HD High Definition audio provides jack retask e De ES ing capability that allows the user to change the function for e each jack through the audio driver Me Lu jack for microphone functionality Audio signals will be present on both of the front and back panel audio connections simultane ously If you want to mute the back panel audio only supported when using an HD front panel audio module refer to instructions on page 85 GA To install a microphone connect your microphone to the Mic in jack and manually configure the High Definition Audio HD Audio HD Audio includes multiple high quality digital to analog converters DACs that support 44 1KHz 48KHz 96KHz 192KHz sampling rate HD Audio features multistreaming capabilities that allow multiple audio streams in and out to be simultaneously processed For example users can listen to MP3 music have an Internet chat make a telephone call over the Internet and etc all at the same time A Configur
73. ing the BIOS with the Q Flash Utility A Before You Begin 1 From GIGABYTE s website download the latest compressed BIOS update file that matches your moth erboard model 2 Extract the file and save the new BIOS file e g 7 4 GMTS2H F1 to your floppy disk USB flash drive or hard drive Note The USB flash drive or hard drive must use FAT32 16 12 file system 3 Restart the system During the POST press the End key to enter Q Flash Note You can access Q Flash by either pressing the End key during the POST or pressing the F8 key in BIOS Setup However if the BIOS update file is saved to a hard drive in RAID AHCI mode or a hard drive attached to an independent IDE SATA controller use the End key during the POST to access Q Flash Award Modular BIOS v6 00PG An Energy Star Ally Copyright C 1984 2010 Award Software Inc GA MA74GMT S2 F7g DEL BIOS Setup F9 XpressRecovery2 lt F12 gt Boot Menu End Qflash 07 12 2010 RS740 SB710 6A669G0DC 00 Because BIOS flashing is potentially risky please do it with caution Inadequate BIOS flashing may result in system malfunction Unique Features 62 B Updating the BIOS When updating the BIOS choose the location where the BIOS file is saved The following procedure as sumes that you save the BIOS file to a floppy disk Step 1 1 Insert the floppy disk containing the BIOS file into the floppy disk drive In the main menu of Q Flash use the up or
74. ing the drivers Failure to do so may affect the driver installation e Some device drivers will restart your system automatically during the driver installation After the system restart Xpress Install will continue to install other drivers After Xpress Install installs all of the drivers a dialog box will appear asking whether to install new GIGABYTE utilities Click Yes to automatically install the utilities Or click No if you want to manually select the utilities to install on the Application Software page later For USB 2 0 driver support under the Windows XP operating system please install the Windows XP Service Pack 1 or later After installing the SP1 or later if a question mark still exists in Universal Serial Bus Controller in Device Manager please remove the question mark by right clicking your mouse and select Uninstall and restart the system The system will then autodetect and install the USB 2 0 driver B Please ignore the popup dialog box es e g the Found New Hardware Wizard displayed 55 Drivers Installation 3 2 Application Software This page displays all the utilities and applications that GIGABYTE develops and some free software You can click the Install button on the right of an item to install it GIGABYTE Chek the Teta button on the right of an application te install i wir based Sy nT bool ihai allows chant syrien hardware miima such CPU and memory and graphics card and much mone ip
75. limit the hard drive will be turned off m Selecting a system energy saving mode i Depending on your needs select a system power saving mode on the Auto Green SA uto main menu and click Save be ara the settings Green Button Description Lau Standby Enters Power on Suspend mode Suspend Enters Suspend to RAM mode mate Disable Disables this function m E The Bluetooth dongle included in the motherboard package allows og you to wake up the system from Suspend to RAM mode without the need to press the power button first kso sam GIGABYTE Note 1 If your cell phone has been configured as the Auto Green key you ll not be able to use it to connect to other Blu etooth device s when Auto Green is enabled Note 2 Whether the Bluetooth dongle is included depends on the motherboard models Before installing the Bluetooth dongle be sure to turn off other Bluetooth receiver on your computer 69 Unique Features Unique Features 70 Chapter 5 Appendix 5 1 Configuring SATA Hard Drive s To configure SATA hard drive s follow the steps below Install SATA hard drive s in your computer Install SATA hard drive s in your computer Configure SATA controller mode in BIOS Setup Configuring RAID set in RAID BIOS Note 1 Note 2 Make a floppy disk containing the SATA RAID AHCI driver for Windows XP ot 2 Install the SATA RAID AHCI driv
76. ll be performed at the scheduled backup time If the computer is turned off before the scheduled backup time the backup will be performed on the next boot Note 3 We recommend that you preserve at least 25 percent of the hard drive space to optimize the storage space for the backups The backups of the changed data will be stored in the original partition of the data Unique Features 68 4 6 Auto Green Auto Green is an easy to use tool that provides users with simple options to enable system power savings via a Bluetooth cell phone When the phone is out of the range of the computer s Bluetooth receiver the sys tem will enter the specified power saving mode r Configuration The Configuration dialog box First you have to set your Bluetooth cell phone as a portable key On the Auto Green main menu click Configure and then click Configure BT devices Select the Blu etooth cell phone that you want to use as the portable key If the screen doesn t display your Bluetooth cell phone click Refresh to let Auto Green re detect the device Before creating a Bluetooth cell phone key make sure your motherboard has a Bluetooth receiver and you have turned on the search and Bluetooth functions on your phone Configuring the Bluetooth cell phone key Q After you select a cell phone the Add Bluetooth Device Wizard as shown on the left ldem Dae pasan Har tus ni hs d cris
77. load BIOS defaults after BIOS update and after the system restarts C After Updating the BIOS Restart your system after updating the BIOS Make sure that the BIOS file to be flashed matches your motherboard model Updating the BIOS with an incorrect BIOS file could cause your system not to boot 65 Unique Features 4 3 EasyTune 6 GIGABYTE s EasyTune 6 is a simple and easy to use interface that allows users to fine tune their system settings or do overclock overvoltage in Windows environment The user friendly EasyTune 6 interface also includes tabbed pages for CPU and memory information letting users read their system related information without the need to install additional software The EasyTune 6 Interface Uose emp ace Seance Reset Tabs Information Tab Function c The CPU tab provides information on the installed CPU and motherboard ie Memory The Memory tab provides information on the installed memory module s You can select memory module on a specific slot to see its information Qe The Tuner tab allows you to change system clock settings and voltages Easy mode allows you to adjust the CPU FSB only Advanced mode allows you to individually change system clock settings and voltages settings using the sliders e Core Boost is configurable only in Advanced mode With Core Boost enabled you can unlock hidden CPU cores or disable the cores that have been activated Not
78. lt lt gt lt gt Move the selection bar to select an item Enter Execute command or enter the submenu Esc Main Menu Exit the BIOS Setup program Submenus Exit current submenu Page Up Increase the numeric value or make changes Page Down Decrease the numeric value or make changes F1 Show descriptions of the function keys F2 Move cursor to the Item Help block on the right submenus only F5 Restore the previous BIOS settings for the current submenus F6 Load the Fail Safe BIOS default settings for the current submenus F7 Load the Optimized BIOS default settings for the current submenus F8 Access the Q Flash utility F9 Display system information lt F10 gt Save all the changes and exit the BIOS Setup program lt F11 gt Save CMOS to BIOS lt F12 gt Load CMOS from BIOS Main Menu Help The on screen description of a highlighted setup option is displayed on the bottom line of the Main Menu Submenu Help While in a submenu press lt F1 gt to display a help screen General Help of function keys available for the menu Press lt Esc gt to exit the help screen Help for each item is in the Item Help block on the right side of the submenu access more advanced options When the system is not stable as usual select the Load Optimized Defaults item to set your system to its defaults The BIOS Setup menus described in this chapter are for reference only
79. m CPU CLK 200 MHz PCle CLK AM3 CPU 100 MHz DDR3 1333 O C 1066 800 MHz Dual Channel Memory 1 PCI Express x16 Hyper Transport Bus GFX CLK 100 MHz PCI Express x16 DVI D HDMI 2 PCI Express Bus AMD 740G PCle CLK 100 MHz i 12 USB Ports 1 PCI Express x1 NS _ ATA 133 100 66 33 IDE Channel co AMD SB710 L 4 SATA 3Gb s NN puros IT8718 PS 2 KB Mouse 2 PCI SOLO PSG 3 5 a PCI CLK d 33 MHz D Only for GA MA74GMT S2H Note Simultaneous output for DVI D and HDMI is not supported 8 Chapter 1 Hardware Installation 1 1 Installation Precautions The motherboard contains numerous delicate electronic circuits and components which can become damaged as a result of electrostatic discharge ESD Prior to installation carefully read the user s manual and follow these procedures Prior to installation do not remove or break motherboard S N Serial Number sticker or warranty sticker provided by your dealer These stickers are required for warranty validation Always remove the AC power by unplugging the power cord from the power outlet before installing or removing the motherboard or other hardware components When connecting hardware components to the internal connectors on the motherboard make sure they are connected tightly and securely When handling the motherboard avoid touching any metal leads or connectors It is best to wear an electrostatic discharge
80. ments below Note the positive and negative pins before connecting the cables Message Power Power Sleep LED Switch PW SPEAK SPEAK Er allt t E 2 TIWwlO 3 ai 2c o a a ie Chassis Intrusion Header Hard Drive Reset Activity LED Switch e MSG PWR Message Power Sleep LED Yellow Purple System Status LED Connects to the power status indicator on the chassis front panel The LED S0 On is on when the system is operating The LED keeps blinking when the sys S1 Blinking tem is in S1 sleep state The LED is off when the system is in S3 S4 sleep S3 S4 S5 Off state or powered off S5 PW Power Switch Red Connects to the power switch on the chassis front panel You may configure the way to turn off your system using the power switch refer to Chapter 2 BIOS Setup Power Management Setup for more information e SPEAK Speaker Orange Connects to the speaker on the chassis front panel The system reports system startup status by is suing a beep code One single short beep will be heard if no problem is detected at system startup If a problem is detected the BIOS ma
81. more FAQs for your motherboard please go to the Support amp Downloads Motherboard FAQ page on GIGABYTE s website Q A O In the BIOS Setup program why are some BIOS options missing Some advanced options are hidden in the BIOS Setup program Press Delete to enter BIOS Setup during the POST In the Main Menu press lt Ctrl gt lt F1 gt to show the advanced options Why is the light of my keyboard optical mouse still on after the computer shuts down Some motherboards provide a small amount of standby power after the computer shuts down and that s why the light is still on How do clear the CMOS values For motherboards that have a CMOS SW button press this button to clear the CMOS values before doing this please turn off the computer and unplug the power cord For motherboards that have a clearing CMOS jumper refer to the instructions on the CLR CMOS jumper in Chapter 1 to short the jumper to clear the CMOS values If your board doesn t have this jumper refer to the instructions on the motherboard battery in Chapter 1 You can temporarily remove the bat tery from the battery holder to stop supplying power to the CMOS which will clear the CMOS values after about one minute Why do still get a weak sound even though have turned my speaker to the maximum volume Make sure your speaker is equipped with an internal amplifier If not try a speaker with power amplifier Why cannot install the onboard HD au
82. ng Ds hg le ass i Figure 2 Appendix 78 5 1 3 Installing the SATA RAID AHCI Driver and Operating System With the SATA RAID AHCI driver diskette and correct BIOS settings you are ready to install Windows Vista XP onto your hard drive s The followings are examples of Windows XP and Vista installation on the AMD SB750 SATA controller A Installing Windows XP Step 1 Restart your system to boot from the Windows XP setup disk and press lt F6 gt as soon as you see the mes sage Press F6 if you need to install a 3rd party SCSI or RAID driver Figure 1 A screen will then appear asking you to specify additional device Windows Setup Press F6 if you need to install a third party SCSI or RAID driver Figure 1 Step 2 Insert the floppy disk containing the SATA RAID AHCI driver and press S Then a controller menu similar to Figure 2 below will appear Select AMD AHCI Compatible RAID Controller x86 platform and press Enter Windows Setup You have chosen to configure a SCSI Adapter for use with Windows using a device support disk provided by an adapter manufacturer Select the SCSI Adapter you want from the following list or press ESC to return to the previous screen AMD AHCI Compatible RAID Controller x86 platform AMD AHCI Compatible RAID Controller x64 platform ENTER Select F3 Exit Figure 2 Step 3 On the next screen press Enter to continue the driver installation After the driver inst
83. o GIGABYTE s lately developed utilities for users to install You can click the Install button on the right of an item to install it GIGABYTE Install Programa Chk th stall buton on the nghi of an application te install it Drivers Installation 58 Chapter 4 Unique Features 4 1 Xpress Recovery2 pres Before You Begin e Xpress Recovery2 will check the first physical hard drive for the operating system Xpress Recovery2 can only back up restore the first physical hard drive that has the operating system installed As Xpress Recovery2 will save the backup file at the end of the hard drive make sure to leave enough un allocated space in advanced 10 GB or more is recommended actual size requirements vary depending on the amount of data e t is recommended to back up your system soon after the operating system and drivers are installed The amount of data and hard drive access speed may affect the speed at which the data is backed up restored e It takes longer to back up a hard drive than to restore it Xpress Recovery is a utility that allows you to quickly compress and back up your system data and perform restoration of it Supporting NTFS FAT32 and FAT16 file systems Xpress Recovery2 can back up data on PATA and SATA hard drives and restore it System Requirements Atleast 512 MB of system memory e VESA compatible graphics card Windows XP with SP1 or later Windows
84. of thermal grease on the surface of the CPU Do not turn on the computer if the CPU cooler is not installed otherwise overheating and dam age of the CPU may occur Set the CPU host frequency in accordance with the CPU specifications It is not recommended that the system bus frequency be set beyond hardware specifications since it does not meet the standard requirements for the peripherals If you wish to set the frequency beyond the standard specifications please do so according to your hardware specifications including the CPU graph ics card memory hard drive etc 1 3 1 Installing the CPU A Locate the pin one denoted by a small triangle of the CPU socket and the CPU A Small Triangle Mark Denotes Pin One of the Socket AM3 Socket L a aa B O s A Small Triangle Marking Denotes CPU Pin One oY Gro LATE bna Hd244EB JY DINI ISUTXIMIONEEE Le INL xl aw E Y milan ma mi bira 13 Hardware Installation B Follow the steps below to correctly install the CPU into the motherboard CPU socket Before installing the CPU make sure to turn off the computer and unplug the power cord f
85. ompleted B Configuring Sound Effect You may configure an audio environment on the Sound Effects tab Appendix 84 C Activating an AC 97 Front Panel Audio Module If your chassis provides an AC 97 front panel audio mod ule to activate the AC 97 functionality click the tool icon on the Speaker Configuration tab On the Connector apr ia a rr EB que os ya po kaaa pected Mints Bre m Patina rm Settings dialog box select the Disable front panel jack detection check box Click OK to complete ma Gi Connecter Lertngs HA 5 ET D Muting the Back Panel Audio For HD Audio Only Click Device advanced settings on the top right corner on the Speaker Configuration tab to open the Device advanced settings dialog box Select the Mute the rear output device when a front headphone plugged in check box Click OK to complete Dee ha reer asia device whens bori hepdghona plugged in Mabe Peet ad rede duia Bees playback Ecol Henne ichs di pue CRE Recording Hrica Dh Teup sare Et al au gda m di de ul device pa al pot jacks os rrcepencent input depen 85 Appendix 5 2 2 Configuring S PDIF In Out The S PDIF In and Out cable optional provides S PDIF In and S PDIF Out functionalities aai Optical S PDIF Out Optical Coaxial S PDIF In SIPDIF Out Coal S PDIFIn Installing the S PDIF In and Out Cable al v
86. oring and Reporting Technology capability of your hard drive This feature allows your system to report read write errors of the hard drive and to issue warnings when a third party hardware monitor utility is installed Default Disabled o Away Mode Enables or disables Away Mode in Windows XP Media Center operating system Away Mode allows the system to silently perform unattended tasks while in a low power mode that appears off Default Disabled c Backup BIOS Image to HDD Allows the system to copy the BIOS image file to the hard drive If the system BIOS is corrupted it will be recovered from this image file Default Disabled c Init Display First Specifies the first initiation of the monitor display from the installed PCI graphics card PCI Express graphics card or the onboard graphics gt gt PCI Slot Sets the PCI graphics card as the first display Default b gt OnChipVGA Sets the onboard graphics as the first display PEG Sets the PCI Express graphics card as the first display Surround View Enables or disables the Surround View function This option is configurable only if an ATI graphics card is installed Default Disabled lt Graphics Display Mode Specifies the graphics display of the onboard graphics output from the D SUB DVI D or D SUB HDMI bp D SUB DVI Sets the D SUB DVI D as the graphics display Default bp D SUB HDMI Sets the D SUB HDMI as the graphics display o Internal Graphics Mode bp Disabled Alw
87. ort for ON OFF Charge Support for Q Share Bundled Software Norton Internet Security OEM version Operating System Support for Microsoft Windows 7 Vista XP Micro ATX Form Factor 24 4cm x 22 0cm Note 1 Due to Windows 32 bit operating system limitation when more than 4 GB of physical memory is installed the actual memory size displayed will be less than 4 CB Note 2 The DVI D port does not support D Sub connection by adapter Note 3 Simultaneous output for DVI D and HDMI is not supported Note 4 To configure 7 1 channel audio you have to use an HD front panel audio module and enable themulti channel audio feature through the audio driver Note 5 Whether the CPU fan speed control function is supported will depend on the CPU cooler you install Note 6 Available functions in EasyTune may differ by motherboard model Hardware Installation 12 1 3 In As stalling the CPU and CPU Cooler ad the following guidelines before you begin to install the CPU Make sure that the motherboard supports the CPU Go to GIGABYTE s website for the latest CPU support list Always turn off the computer and unplug the power cord from the power outlet before installing the CPU to prevent hardware damage Locate the pin one of the CPU The CPU cannot be inserted if oriented incorrectly Or you may locate the notches on both sides of the CPU and alignment keys on the CPU socket Apply an even and thin layer
88. r the CMOS values may not be accurate or may be lost You may clear the CMOS values by removing the battery 1 Turn off your computer and unplug the power cord 2 Gently remove the battery from the battery holder and wait for one minute Or use a metal object like a screwdriver to touch the positive and negative terminals of the battery holder making them short for 5 seconds 3 Replace the battery 4 Plug in the power cord and restart your computer e Always turn off your computer and unplug the power cord before replacing the battery A e Replace the battery with an equivalent one Danger of explosion if the battery is replaced with an incorrect model e Contact the place of purchase or local dealer if you are not able to replace the battery by your self or uncertain about the battery model e When installing the battery note the orientation of the positive side and the negative side of the battery the positive side should face up e Used batteries must be handled in accordance with local environmental regulations 29 Hardware Installation Hardware Installa
89. ration No CMOS Setup Utility Copyright C 1984 2010 Award Software Advanced Clock Calibration EC Firmware Selection Normal Item Help Advanced Clock Calibration Disabled Menu Level bb Value All Cores 2 Value Core 0 Value Core 1 Value Core 2 Value Core 3 2 CPU core Control Auto CAL Cow D Enabled CPU Core OS Enabled 0 2808 00 P AD Enabled CPU Core 3 Neto Enabled CPU Core 4 Mio Enabled CPU Core 5 Neto Enabled TL Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults Note This item appears only if you install a CPU that supports this feature 35 BIOS Setup EC Firmware Selection Allows you to select the EC firmware version when Advanced Clock Calibration is enabled After the selection select Save amp Exit Setup in the BIOS Main Menu and then press Y A message which says BIOS Is Updating EC Firmware Don t Turn Off Or Reset System will appear Wait for a few seconds and the system will automatically restart for the settings to take effect gt gt Normal Uses the standard AMD EC firmware version Default gt gt Hybrid Uses the specific AMD EC firmware version Advanced Clock Calibration Allows you to determine whether to enable Advanced Clock Calibration when using an AMD Black Edi tion CPU gt gt Disabled Disables this function Default gt gt Auto Lets the BIOS to configure
90. rboard Technology Guide page on our website For product related information check on our website at http www gigabyte com Identifying Your Motherboard Revision The revision number on your motherboard looks like this REV X X For example REV 1 0 means the revision of the motherboard is 1 0 Check your motherboard revision before updating motherboard BIOS drivers or when looking for technical information Example Table of Contents POLO ea un 6 OO AA RH 6 GA MA74GMT S2H GA MA74GMT S2 Motherboard Layout T GA MA74GMT S2H GA MA74GMT S2 Motherboard Block Diagram 8 Chapter 1 Hardware Installation sse 9 tr installation mk e RA menu 9 t2 POUCES D CIDE ee ds cms eium oi Mme EDI 10 1 3 Installing the CPU and CPU Cooler 13 t31 Installing the CPU 13 1 3 2 Installing the CPU C00 aaa ad en en 15 1 4 Installing the Memory daa GAGANA AKA KAL 16 1 4 1 Dual Channel Memory Configuration sens 16 14 2 Installing o TL 17 1 5 Installing an Expansion Card seen 18 1 6 Back Panel Connectors 19 tr tema COR eee scares basse to easauee ee eecaaaceteeuaaeee 21 Chapter 2 BIOS SOM AA AA AA 31 Pa ele CIC cscs EE SE a 32 2 2 The MAIN MONU ses a ea delere vsus Jo 2 3 MB Intelligent Tweaker M IL T maman 35 2 4 Standard CMOS Fe
91. rom the power outlet to prevent damage to the CPU Do not force the CPU into the CPU socket The CPU cannot fit in if oriented incorrectly Adjust the CPU orientation if this occurs CPU Socket Locking Lever Hardware Installation Step 1 Completely lift up the CPU socket locking lever Step 2 Align the CPU pin one small triangle marking with the triangle mark on the CPU socket and gently insert the CPU into the socket Make sure that the CPU pins fit perfectly into their holes Once the CPU is positioned into its socket place one finger down on the middle of the CPU lowering the locking lever and latching it into the fully locked position 1 3 2 Installing the CPU Cooler Follow the steps below to correctly install the CPU cooler on the CPU The following procedure uses the GIGABYTE cooler as the example 066066044000 Step 1 Apply an even and thin layer of thermal grease on the surface of the installed CPU Hook the CPU cooler clip to the mounting lug on one side of the retention frame On the other side push straight down on the the CPU cooler clip to hook it to the mounting lug on the reten tion frame Step 5 Step 4 Turn the cam handle from the left side to the right side as the picture above shows to lock into place Refer to your CPU cooler installation manual for instructions on installing the cooler Finally attach the power connector of the CPU cooler to the CPU f
92. rs If a cable problem occurs on a specified pair of wires the Status field will show Short and then length shown will be the approximate distance to the fault or short Example Part1 2 Status Short Length 2m Explanation A fault or short might occur at about 2m on Part 1 2 Note Part 4 5 and Part 7 8 are not used in a 10 100 Mbps environment so their Status fields will show Open and the length shown is the approximate length of the attached LAN cable 45 BIOS Setup lt Onboard Audio Function Enables or disables the onboard audio function Default Enabled If you wish to install a 3rd party add in audio card instead of using the onboard audio set this item to Disabled USB Controllers Enables or disables the integrated USB controllers Default Enabled Disabled will turn off all of the USB functionalities below USB Legacy Function Allows USB keyboard to be used in MS DOS Default Enabled USB Storage Function Determines whether to detect USB storage devices including USB flash drives and USB hard drives during the POST Default Enabled c Onboard Serial Port 1 Enables or disables the first serial port and specifies its base I O address and corresponding interrupt Options are Auto 2F8 IRQ3 3F8 IRQ4 default 3E8 IRQ4 2E8 IRQ3 Disabled BIOS Setup 46 2 7 Power Management Setup CMOS Setup Utility Copyright C 1984 2010 Award Software Power Management Setup ACPI Suspend Type S3 STR Item Help Soft
93. s pressed for less than 4 seconds the system will enter suspend mode o USB Wake Up from S3 Allows the system to be awakened from ACPI S3 sleep state by a wake up signal from the installed USB device Default Enabled lt Modem Ring Resume Allows the system to be awakened from an ACPI sleep state by a wake up signal from a modem that supports wake up function Default Disabled lt gt PME Event Wake Up Allows the system to be awakened from an ACPI sleep state by a wake up signal from a PCI or PCle de vice Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead Default Enabled Note Supported on Windows 7 Vista operating system only 47 BIOS Setup c HPET Support Note Enables or disables High Precision Event Timer HPET for Windows 7 Vista operating system Default Enabled Power On By Mouse Allows the system to be turned on by a PS 2 mouse wake up event Note To use this function you need an ATX power supply providing at least 1A on the 5VSB lead gt gt Disabled Disables this function Default gt gt Double Click Double click on left button on the PS 2 mouse to turn on the system lt gt Power On By Keyboard Allows the system to be turned on by a PS 2 keyboard wake up event Note you need an ATX power supply providing at least 1A on the 5VSB lead gt Disabled Disables this function Default gt Password Set a password with 1 5 characters to turn on the system
94. s successfully 1 long 3 short Keyboard error 2 short CMOS setting error 1 long 9 short BIOS ROM error 1 long 1 short Memory or motherboard error Continuous long beeps Graphics card not inserted properly 1 long 2 short Monitor or graphics card error Continuous short beeps Power error 91 Appendix 5 3 2 Troubleshooting Procedure If you encounter any troubles during system startup follow the troubleshooting procedure below to solve the problem Turn off the power Remove all peripherals connecting cables and power cord etc Make sure the motherboard does not short circuit with the chassis or other metal objects Yes Isolate the short circuit No The problem is verified and solved Secure the CPU cooler No on the CPU Connect the Check if the CPU cooler is attached to the CPU securely Is the pow er connector of the CPU cooler connected to the CPU_FAN header properly CPU cooler power cable to the motherboard Yes The problem is verified and solved Correctly insert the Check if the memory is installed properly on the memory slot memory into the memory socket Yes Insert the graphics card Connect the ATX main power cable and the 12V power cable Turn on the power to start the computer Make sure the graphics card is securely seated in the expansion slot and power connectors are firmly attached The problem is verified and solved Continued Appendix 92
95. ss Enter Item Help HT Link Frequency Auto Menu Level gt CPU Clock Ratio Auto CPU NorthBridge Freq Auto CPU Host Clock Control Auto CPU Frequency MHz 200 PCIE Clock MHz Auto VGA Core Clock MHz 400 Set Memory Clock Auto x Memory Clock x4 00 800Mhz gt DRAM Configuration Press Enter wack System Voltage Optimized kx System Voltage Control Auto DDR3 Voltage Control Auto NorthBridge Volt Control Auto SouthBridge Volt Control Auto CPU NB VID Control Auto CPU Voltage Control Auto Normal CPU Vcore 1 2500V 142 Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults dent on your overall system configurations Incorrectly doing overclock overvoltage may result in damage to CPU chipset or memory and reduce the useful life of these components This page is for advanced users only and we recommend you not to alter the default settings to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs clear the CMOS values and reset the board to default values When the System Voltage Optimized item blinks in red it is recommended that you set the System Voltage Control item to Auto to optimize the system voltage settings i Whether the system will work stably with the overclock overvoltage settings you made is depen lt Advanced Clock Calib
96. stable power to all the components on the motherboard Before connecting the power connector first make sure the power supply is turned off and all devices are properly installed The power connector possesses a foolproof design Connect the power supply cable to the power connector in the correct orientation The 12V power connector mainly supplies power to the CPU If the 12V power connector is not connected the computer will not start To meet expansion requirements it is recommended that a power supply that can withstand high power consumption be used 500W or greater If a power supply is used that does not provide the required power the result can lead to an unstable or unbootable system ATX 12V j j Pin No Definition 1 GND 2 GND BH 3 12V 4 12V ATX_12V ATX Pin No Definition Pin No Definition 1 3 3V 13 3 9V 2 3 3V 14 12V 3 GND 15 GND 4 5V 16 PS_ON soft On Off 5 GND 17 GND 6 5V 18 GND T GND 19 GND 8 Power Good 20 5V 9 5VSB stand by 5V 21 5V 10 12V 22 5V 11 12V Only for 2x12 pin ATX 23 5V Only for 2x12 pin ATX 12 3 3V Only for 2x12 pin ATX 24 GND Only for 2x12 pin ATX
97. sult in system malfunction e BIOS will emit a beep code during the POST Refer to Chapter 5 Troubleshooting for the beep codes description It is recommended that you not alter the default settings unless you need to to prevent system instability or other unexpected results Inadequately altering the settings may result in system s failure to boot If this occurs try to clear the CMOS values and reset the board to default values Refer to the Load Optimized Defaults section in this chapter or introductions of the battery clearing CMOS jumper in Chapter 1 for how to clear the CMOS values 91 BIOS Setup 2 1 Startup Screen The following screens may appear when the computer boots Award Modular BIOS v6 00PG An Energy Star Ally Copyright C 1984 2010 Award Software Inc GA MA74GMT S2 F7g Motherboard Model BIOS Version lt DEL gt BIOS Setup lt F9 gt XpressRecovery2 lt F12 gt Boot Menu lt End gt Qflash 0 12 2010 RS740 SB710 6A669G0DC 00 Function Keys lt DEL gt BIOS SETUP Press the lt Delete gt key to enter BIOS Setup F9 XPRESS RECOVERY2 If you have ever entered Xpress Recovery2 to back up hard drive data using the driver disk the F9 key can be used for subsequent access to Xpress Recovery2 during the POST For more information refer to Chapter 4 Xpress Recovery2 lt F12 gt BOOT MENU Boot Menu allows you to set the first boot device without entering BIOS Setup In Boot M
98. t F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults c OnChip SATA Controller Enables or disables the integrated SATA controller Default Enabled lt OnChip SATA Type SATA2 0 SATA2 3 connectors Configures the operating mode of the integrated SATA2 0 SATA2 3 controller gt gt Native IDE Allows the SATA controller to operate in Native IDE mode Default Enable Native IDE mode if you wish to install operating systems that support Native mode bp RAID Enables RAID for the SATA controller gt gt AHCI Configures the SATA controllers to AHCI mode Advanced Host Controller Interface AHCI is an interface specification that allows the storage driver to enable advanced Serial ATA features such as Native Command Queuing and hot plug Green LAN When the onboard LAN function and Green LAN are enabled the system will dynamically detect if a LAN cable is connected or not If not the corresponding LAN controller will be disabled automatically Default Disabled lt Onboard LAN Function Enables or disables the onboard LAN function Default Enabled If you wish to install a 3rd party add in network card instead of using the onboard LAN set this item to Disabled lt Onboard LAN Boot ROM Allows you to decide whether to activate the boot ROM integrated with the onboard LAN chip Default Disabled BIOS Setup 44 SMART LAN LAN Cable Diagnostic Function CMOS Setup Utility Copyright C
99. tance in recycling reusing in your end of life product you may contact us at the Customer Care number listed in your product s user s manual and we will be glad to help you with your effort Appendix 94 Finally we suggest that you practice other environmentally friendly actions by understanding and using the energy saving features of this product where applicable recycling the inner and outer packaging including shipping containers this product was delivered in and by disposing of or recycling used batteries properly With your help we can reduce the amount of natural resources needed to produce electrical and electronic equipment minimize the use of landfills for the disposal of end of life products and generally improve our quality of life by ensuring that potentially hazardous substances are not released into the environment and are disposed of properly China Restriction of Hazardous Substances Table The following table is supplied in compliance with China s Restriction of Hazardous Substances China RoHS requirements LTE PO TRA ANA GM Management Methods on Control of Pollution from Electronic Information Products China RoHS Declaration PFugscd EE VOLEMERBREBEE Hazardous Substances Table EE WARE ETEL ka Cr Wii PEE PBDE BP FIT PE UP Mechanical parts and Fan Egi AE F RHEHH Flux older Paste Label and other DATER A OUR ERA SR hA EEST 0ER ERA T Indicates that this hazardous substance
100. ter system startup br Access Mode Sets the hard drive access mode Options are Auto default Large BIOS Setup 40 The following fields display your hard drive specifications If you wish to enter the parameters manually refer to the information on the hard drive bp Capacity Approximate capacity of the currently installed hard drive bp Cylinder Number of cylinders bp Head Number of heads gt gt Precomp Write precompensation cylinder bp Landing Zone Landing zone gt gt Sector Number of sectors Drive A Allows you to select the type of floppy disk drive installed in your system If you do not install a floppy disk drive set this item to None Options are None 360K 5 25 1 2M 5 25 720K 3 5 1 44M 3 5 2 88M 3 5 Floppy 3 Mode Support Allows you to specify whether the installed floppy disk drive is 3 mode floppy disk drive a Japanese standard floppy disk drive Options are Disabled default Drive A Halt On Allows you to determine whether the system will stop for an error during the POST gt gt All Errors Whenever the BIOS detects a non fatal error the system boot will stop gt gt No Errors The system boot will not stop for any error gt gt All But Keyboard The system boot will not stop for a keyboard error but stop for all other errors Default gt gt All But Diskette The system boot will not stop for a floppy disk drive error but stop for all other errors gt gt All But Disk Key
101. tion 30 Chapter 2 BIOS Setup BIOS Basic Input and Output System records hardware parameters of the system in the CMOS on the motherboard Its major functions include conducting the Power On Self Test POST during system startup saving system parameters and loading operating system etc BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features When the power is turned off the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS To access the BIOS Setup program press the Delete key during the POST when the power is turned on To see more advanced BIOS Setup menu options you can press Ctrl F1 in the main menu of the BIOS Setup program To upgrade the BIOS use either the GIGABYTE Q Flash or BIOS utility e Q Flash allows the user to quickly and easily upgrade or back up BIOS without entering the operating system e BIOS is a Windows based utility that searches and downloads the latest version of BIOS from the Internet and updates the BIOS For instructions on using the Q Flash and BIOS utilities refer to Chapter 4 BIOS Update Utilities Because BIOS flashing is potentially risky if you do not encounter problems using the current A version of BIOS it is recommended that you not flash the BIOS To flash the BIOS do it with caution Inadequate BIOS flashing may re
102. u wish to use refer to the steps below The following steps explain how to enable Stereo Mix which may be needed when you want to record sound from your computer Step 1 Locate the Volume icon in the notification area and right click on this icon Select Recording Devices CM5 5 45 PM Step 2 On the Recording tab right click on an empty space and select Show Disabled Devices ha pA nG hiki r Bais AA Pa EH aro pr Birra 3 atri Heb Davies fue Wai Do basi o 89 Appendix Step 3 When the Stereo Mix item appears right click on this item and select Enable Then set it as the default de vice Step 4 ss 1 b port Jo que euo e m Now you can access the HD Audio Manager to config lint y ure Stereo Mix and use Sound Recorder to record the baa c sound pa a rm F e dE B gt E ARTE 5 2 4 Using the Sound Recorder N Sound Recorder A Recording Sound 1 Make sure you have connected the sound input device e g microphone to the computer 2 To record the audio click the Start Recording button ss 3 To stop recording audio click the Stop Recording button ses Be sure to save the recorded audio file upon completion B Playing the Recorded Sound You can play your recording in a digital media player program that supports your audio file format Appendix 90 5 3 Troubleshooting 5 3 1 Frequently Asked Questions To read
103. xit the RAID BIOS utility View Drive Assignments The View Drive Assignments option in the Main Menu displays whether the attached hard drives are as signed to a disk array or are unassigned Under the Assignment column drives are labeled with their as signed disk array or shown as Free if unassigned Option ROM Utility c 2008 Advanced Micro Devices Inc View Drives Assignments Channel ID Drive Model Capabilities i Assignment WDC WD800JD 22LSA0 SATA 3G Extent 1 WDC WD800JD 22LSA0 SATA 3G Extent 1 Keys Available 1 Up 4 Down ESC Exit Ctrl H Secure Erase PEUp Dn Page Change Figure 8 75 Appendix Delete an Array The Delete Array menu option allows for deletion of disk array assignments Deleting an existing disk array could result in loss of data Record all array information including the array type the disk members and stripe block size in case you wish to undo a deletion 1 To delete an array press lt 3 gt in the Main Menu to enter the Delete LD Menu Then highlight the array you wish to delete and press the Delete key or the lt Alt gt lt D gt keys 2 The View LD Definition Menu will appear as shown in Figure 9 showing which drives are assigned to this array Press lt Ctrl gt lt Y gt if you are sure to delete the array or other keys to abort 3 When the array is deleted the screen will return to Delete LD Menu Press lt Esc gt to return to Main Menu Option ROM Utility c 2
104. y issue beeps in different patterns to indicate the problem Refer to Chapter 5 Troubleshooting for information about beep codes e HD Hard Drive Activity LED Blue Connects to the hard drive activity LED on the chassis front panel The LED is on when the hard drive is reading or writing data e RES Reset Switch Green Connects to the reset switch on the chassis front panel Press the reset switch to restart the computer if the computer freezes and fails to perform a normal restart e Cl Chassis Intrusion Header Gray Connects to the chassis intrusion switch sensor on the chassis that can detect if the chassis cover has been removed This function requires a chassis with a chassis intrusion switch sensor The front panel design may differ by chassis A front panel module mainly consists of power ER non reset switch power LED hard drive activity LED speaker and etc When connecting your chassis front panel module to this header make sure the wire assignments and the pin assign ments are matched correctly 25 Hardware Installation 9 F AUDIO Front Panel Audio Header The front panel audio header supports Intel High Definition audio HD and AC 97 audio You may connect your chassis front panel audio module to this header Make sure the wire assignments of the module con nector match the pin assignments of the motherboard header Incorrect connection between the module connector and the motherboard head
105. y not be effective o ErP Support Determines whether to let the system consume less than 1W power in S5 shutdown state Default Disabled Note When this item is set to Enabled the following four functions will become unavailable PME event wake up power on by mouse power on by keyboard and wake on LAN Note Supported on Windows 7 Vista operating system only BIOS Setup 48 2 8 PnP PCI Configurations CMOS Setup Utility Copyright C 1984 2010 Award Software PnP PCI Configurations PCI1 IRQ Assignment Auto Item Help PCI2 IRQ Assignment Auto Menu Level Ne Move Enter Select PU PD Value F10 Save ESC Exit F1 General Help F5 Previous Values F6 Fail Safe Defaults F7 Optimized Defaults lt PCI1 IRQ Assignment Auto BIOS auto assigns IRQ to the first PCI slot Default b gt 3 4 5 7 9 10 11 12 14 15 Assigns IRQ 3 4 5 7 9 10 11 12 14 15 to the first PCI slot c PCI2 IRQ Assignment gt gt Auto BIOS auto assigns IRQ to the second PCI slot Default bo 3 4 5 7 9 10 11 12 14 15 Assigns IRQ 3 4 5 7 9 10 11 12 14 15 to the second PCI slot 49 BIOS Setup 2 9 PC Health Status CMOS Setup Utility Copyright C 1984 2010 Award Software PC Health Status Reset Case Open Status Disabled Item Help Case Opened No Menu Level Vcore 1 364V DDR3 1 5V 1 600V TIN 3 280 V ar PAY 12 048V Current System Temperature 38 C Current CPU Temperature 36 C Current CPU FAN Speed 1962 RPM Current SYST
106. y2 will save the backup file to the unallocated o space black stripe along the top Please note that if there is no enough unallocated space Xpress Recovery2 cannot save the backup file B Accessing Xpress Recovery2 1 Boot from the motherboard driver disk to access Xpress Recovery2 for the first time When you see the following message Press any key to startup Xpress Recovery2 press any key to enter Xpress Recovery2 2 After you use the backup function in Xpress Recovery2 for the first time Xpress Recovery2 will stay permanent in your hard drive If you wish to enter Xpress Recovery2 later simply press lt F9 gt during the POST C Using the Backup Function in Xpress Recovery2 ps PEDE IM Hai m GIGABYTE fh TE CH K LLL LLL mm Step 1 Step 2 Select BACKUP to start backing up your hard drive When finished go to Disk Management to check data disk allocation Unique Features 60 D Using the Restore Function in Xpress Recovery2 b E Select RESTORE to restore the backup to your hard drive in A GIGABYTE ase ne system pigaka down The RESTORE option will not be TECHNOLOGY present if no backup is created before b eee ww m ie ee cu Uxd waMw agama GIGABYTE TECHHOLOG Step 1 E Step 2 If you wish to remove the backup file select After the backup file is removed no backup image REMOVE file will be present in Disk Management and hard driv
Download Pdf Manuals
Related Search
Related Contents
Entraînement Décodage CP ≈ Module 1 Télécharger - IAM Air Transport District 140 Mode d`emploi MKT 5510 C - Migros Manual de instalación, funcionamiento y mantenimiento Discovery Copyright © All rights reserved.