Caliber MCD 795
Contents
1. End user can press the MODE button repeatedly until the MAIN MENU appear on the screen then press the mode button to get into the GPS NAVIGATION MODE Media Or end user when in any mode short pressing the GPS MODE TA button on the front panel to get into the GPS NAVIGATION MODE Unit should start to load the GPS NAVIGATION SOFTWARE If the GPS NAVIGATION has not been activated before or the GPS NAVIGATION is not in used and the ATTENTION SCREEN should appear Sometimes the loading of the GPS NAVIGATION SOFTWARE may take a while but this is normal End user should read the ATTENTION CONTENT CAREFULLY before pressing the ACCEPT button Navigation Operation Attention If you are using the software product during driving or transportation we strongly advise you to direct all your attention to driving or transportation and to Especially do not try to operate enter data into or obtain data from the software product while driving because such presents a life hazard and the lack of proper attention may cause death injury or matertal damge 4 Once pressd the ACCEPT BUTTON unit will get into the GPS NAVIGATION MODE and the below screen will appear And now end user is ready to enjoy the GPS NAVIGATION SYSTEM of this unit z Cockpit TE settings No GPS signal ro o About 05 VA rind amp Go Exit 5 For the details operat2. Note Please refer to the Installing the GPS Aerial For the proper mounting or installation of this GPS AERIAL TD n 5 Tm JN LL e e VIDEO INPUT YELLOW VIDEO IN 1 LL VCR or DVD AUDIO INPUT RIGHT RED AUDIOINR lt v AUDIO IN R GAME CONSOLE AUDIO INPUT LEFT SUB W OUT GPS AERIAL Connecting the System Wiring Diagram Power Speakers FUSE 20 PIN AUDIO POWER HARNESS See Figure 1 IU 0 Not supplied ANTENNA EXTENDER CABLE ANTENNA Not supplied T RCA TO RCA a 9 GREY WHITE _ CABLES REAR 5 as CHANNEL L ue S a CU z H 9 fy BLACK WHITE FRONT m H CHANNEL LA RED g BLUE WHITE T TRIPE il 1 2 Connect to power amplifier If not used T dr dm POWER T b d f wi ll AMPLIFIER ape bare end of wire 9 PINK Brake Switch PARKING BRAKE Connect to Parking Brake 2 5m extension wire Ground ISO CONNECTOR See Figure 2 HOLO3NNOO V HOLO3NNOO Figure 2 ISO CONNECTOR 4 PIN 8 PIN FEMALE WITH MALE TERMINAL ISO CONNECTOR WIRING CHART PIN WIRE COLOR FUNCTION LABEL A4 YELLOW BATTERY A5 BLUE POWER ANTENNA A7 RED_ IGNITION ACC GROUND A8 BLACK
3. to cycle through each possible option or display a list of the available options TV Dispaly The Display setting allows the user to select the TV display The following options are available Media Player TV Type Display ______ 5 Normal LB gt le Angle mark Wide le Screensaver TV display mode setup Normal LB The Display setting allows the user to select the TV type The following options are available Angle Mark Display E Tv display NTSC ie Ange eer PAL gt Auto gt Screen saver 7 TV standard setup NTSC The Display setting allows the user to select the Angle mark on off mode Media Player Screen Saver End user can use this function to turn on or off the screen saver Rifai Screen saver setup Off Audio Setting Press on the remote control or touch screen W buttons move to the Audio button The list of Audio optional will appear as follow CIS Use the buttons to select the setting Usethe YW buttons to change among the avaitable settings Press Ok or touch screen to cycle through each possible option or display a list ofthe available options Media Player Downmix The Audio setting allows the user to select the Downmix and set downmix setup stereo analog output of this Player Downmix setup Stereo Dual Mono The Audio setting allows the user to s
4. Use only the parts included with the unit to ensure proper installation The use of unauthorized parts can cause malfunctions or permanent damage to the unit Consult with your nearest dealer if installation requires the drilling of holes or other modifications ofthe vehicle Install the unit where it does not get in the driver s way and cannot injure the passenger if there is a sudden stop like an emergency stop 30 If installation angle exceeds 30 Psi from horizontal the unit might not give its optimum performance Avoid installing the unit where it would be subject to high temperature such as from direct sunlight or from hot air from heater or where it would be subject to dust dirt or excessive vibration Be sure to remove the front panel before installing the unit Din front rear mount This unit can be property installed either from Front conventional DIN Front mount or Rear DIN Rear mount installation utilizing threaded screw holes the sides of the unit chassis For details refer to the following illustrated installation methods Aand B Din front mount Method A No Content 1 Dashboard 2 Holder After inserting the half sleeve into the dashboard select the appropriate tab according to the thickness of the dashboard material and bend them inwards to secure the holder in place 3 Screw Installation the Unit No Content Dashboard Nut bmm opring washer Screw 4X12mm Screw Su
5. When the entered password is not matching the Passwords do no match message will appear i Parental j Change Parent e Default Change password End user should try to re enter the password again and press the OK or touchscreen to confirm Parental em _ chanse Parent 8 Default Change password Parental Level This function is to enter the Parental level control setup Media Player amp Parental Change EHBENHENNB 8 Aduit Set to 8 Adult Press the OK or touch screen to enter the password amp Parental I change ETAT Set to 8 If the password is not correct the Wrong Password message will appear SE Parental 18 T 8 Set to 8 Adult End user should try to re enter the correct password again and press the OK or touch screen to confirm Media Player Parental e ri x E Dn gt E Change Change e Parent e Default Change password Default Setting the Default function will reset all options and your personal settings to the factory defaults and all your personal settings will be erased Use the buttons to select the setting Parental e Change Parent EX Load factory settings Press the OK or touch screen to confirm the selection SELECT MENU LANGUAGE Ma
6. INSTRUCTION MANUAL MODEL NO MCD795 In Car Navigation Media Player Important Safety Information End user must read this section before operating this unit Operation of the unit is permitted only if traffic conditions are suitable and you are absolutely sure that you your passengers or other motorists are not endangered obstructed or inconveni ienced In all cases all applicable road traffic regulations must be obeyed DESTINATIONS MAY ONLY BE ENTERED WHEN THE VEHICLE IS STATIONARY The navigation system is only an aid Errors may occur in individual data items entries At all times the driver must decide whether or not to heed the information provided We do not accept liability for erroneous data provided by the navigation system Due to continual changes in traffic routing or deviations in the data it may occur that imprecise or erroneous information is given Therefore actual road signs and traffic regulations must always be observed In particular the navigation system can not be used as an orientation aid at times of poor visibility Theunit may only be used for its intended purpose The volume of the radio navigation system should be adjusted so that external noise is still audible Use the proper power supply this product is designed to operate with a 12 volt DC negative ground battery system Protect the disc mechanism avoid inserting any foreign objects into the slot of this player Failure
7. Eject Open closed panelorto slide up close an opened panel Loading a CD Panel in the slide down position the disc slot become accessible Insert a CD through the disc slot the CD will be automatically load and the panel will also close automatically amp playback will begin If no CD is inserted press Open button again to slide up the panel Ejecting a CD Press Open button to slide down the panel if a CD is loaded it will be ejected automatically No further key press is needed If the ejected CD is not being removed after 10 seconds it will be reloaded automatically And the panel will automatically slide up after disc has been reloaded Caution If the ejected disc remains in the slot the Open button will not function so closing the panel by using Open button is prevented unless the disc is removed or reloaded Panel angle Adjustment End user can adjust the panel viewing angle of the display to obtain the optimum viewing angle inside the vehicle There are TWO sb can be adjusted by Long pressing the panel Eject Open button 1stlong press to into Angle 1 2nd long press to get into Angle 2 3rd long press to resume to the normal position Caution Please always use the OPEN button to slide up down the front panel Please never try to slide up or down the front panel manually this will cause serious amp permanent damage to the slide down mechanism and this will void the warranty Please do not
8. domain domain attribute File attribute selection In non search state press remote control or tap touch screen lt gt button to move the cursor to file attribute domain then press on remote control or tap touch screen A or V button to select Audio Image Video file attribute and press OK button on remote control or tap touch screen button to determine the attribute you selected Folder File selection Press on remote control or tap touch screen 4 gt button to move the cursor to folder or file domain By pressing number A W key to select the song you want to play then press OK button on remote control or tap touch screen key to play the selected song Also you may press PREV 8 or NEXT 7 key to play the previous or the next song while play and pause Media Player Note Other operation are the same as CD VCD like repeat program and so on Please refer to the CD VCD Disc Operation section 10811 Up Down Right Left Enter Press on remote control or tap touch screen 4 4 gt button to move the cursor Press OK button on remote control or tap touch screen button to confirm the selection OSD MMN Video OSD information item Press OSD state change 1 OSD gt 2 OSD gt 3 OSD gt OSD off 1 OSD 0 1358 0 52 30 2 OSD 2640x490 S 3 OSD Subtitle Play mode E 3rd OSD Current File Time Title Time Remain File Time Media Player
9. earth more than one product together with the earth from another product For example you must separately earth any amplifier unit away from the earth of this navigation system Connecting earths together can cause a fire and or damage the products if their earths became detached Before installing this navigation system This navigation system is for vehicles with a 12 volt battery and negative earthing Please check the battery voltage of your vehicle before installation To avoid shorts in the electrical system be sure to disconnect the battery cable before beginning installation Fors Connecting the System About Parking Wire Caution In order to avoid any accident the driver must not watch video while driving This unit is designed to not allow watching moving video while driving Park your car in a safe place and engage the parking brake before watching moving video Note If watch moving video from Disc or AV In source but Parking Brake IS NOT PROPERLY CONNECTED the video signal will be blocked by the system and the below display will be shown on the unit screen Reminder Video Lock Engage Parking Brake to enjoy Video Note The Video Blocking system under Parking Brake NOT ENGAGED only control this unit s display This system will not affect the Video Output thru the rear RCA Video Output Connecting the System Wiring Diagram Audio Video Connections GPS AERIAL
10. 60dB 1khz Video Color System NTSC PAL Video Output Composite 1 0 Vp p 0 2 75 ohm Video Input Composite 1 0 Vp p 0 2 75 ohm Audio Max Output Power 75W x4 channels Load Impedance speakers 4 ohms Digital Output 900mV Line outlevel load 400mV 10k ohm load Line out Impedance 200 ohm Auxiliary Input Frequency response 20Hz to 20KHz 3dB Input Maximum Voltage 1200mV Input Impedance 4 7 k ohm GPS Navigation GPS Receiver Reception system 20 channel multi channel reception system Reception frequency 1575 42 MHZ Sensitivity 130 dBm Position update frequency Approx once per second GPS aerial Patch Antenna 25mm x 25mm x 2 Aerial cable 5 0 meter Dimensions W x Hx D 40x 16x 50mm Trouble Shooting Before going through the check list check wiring connection If any of the problems persist after check list has been made consult your nearest service dealer Symptom No power The car ignition is not on If the power supply is properly connected to the car accessory terminal switch the ignition key to ACC The fuse is blown Replace the fuse Disc cannot be Presence of CD disc Remove the disc in the player loaded or inside the player then put a new one Seco Inserting the disc in Insert the compact disc with the reverse direction label facing upward Compact disc is extremely Clean the disc or try to play a dirty or defective disc new one Temperature inside Cool off or until the am
11. B1 VIOLET RIGHT REAR SPEAKER VIOLET B2 VIOLET BLACK RIGHT REAR SPEAKER GREY B4 GREY BLACK RIGHTFRONTSPEAKER Bs WHITE _LEFTFRONT SPEAKER B6 WHITE BLACK LEFTFRONTSPEAKER B7 GREEN 11 12 13 14 15 Pin View Figure 1 20 PIN AUDIO POWER HARNESS WIRECOLOR FUNCTION LABEL 1 GREY BLACK RIGHTFRONTSPEAKER 2 GREY RIGHT FRONT SPEAKER 3 VIOLET RIGHT REAR SPEAKER 4 VIOLET BLACK RIGHTREARSPEAKER 5 PINNK PARKINGBRAKEC 6 GREEN LEFT REAR SPEAKER 8 RED JIGNITION ACC 9 BLACK REAR PRE AMPLIFIER LINE OUT COMMON 10 RED RIGHT REAR PRE AMPLIFIER LINE OUT 11 WHITE LEFT FRONT SPEAKER 12 WHITE BLACK_ LEFTFRONTSPEAKER 13 BLUE WHITE POWERAMPLIFIERREMOTE 14 BLUE POWERANTENNA 15 YELLOW BATTERY 16 BLACK CHASSIS GROUND 18 RED RIGHT FRONT PRE AMPLIFIER LINE OUT 19 BLACK FRONTPRE AMPLIFIER LINE OUT COMMON 20 WHITE LEFTREARPRE AMPLIFIER LINE OUT Installing the GPS Antenna Aerial Parts Supplied Setting Description Cc GPS aerial lt gt Metal sheet Clamp 5 pcs LF Waterproof pad When installing the aerial inside the vehicle on the rear shelf Affix the metal sheet on as level a surface as possible where the GPS antenna aerial faces
12. IN Mode 2 Aceess to MAIN MENU and tap li MEDIAPLAYER the following buttons to start playing the desired media sources ig button to play files in USB 0 button to playing the Disc R Button to play the files in SD card Media Player Note If any media device is not avaiable in this unit this media souurce will not appear during Mode switch or on the touch screen Note This unit only can playback the SD Card which is inserted in the main unit Please refere to the page Overview of the unit for more details of the SD card slot for media player use Color setting during DVD video disc playback Tapping touch screen button to access into the DVD video color setting The below Set Up menu will appear COLOR lt X BRIGHTNESS _ lt E Ver CONTRAST rm gt HUE x E a 54 Change setting for Color 4 Change setting for Brightness Change setting for Contrast RESET Reset to default setting TRAST mm Change setting for Hue x Exit Color configuration menu Media Player Navigation While Media Player Playback Y Navigation Voice Guidance on or off under Media Player playback This unit will automacitally MUTE the audio output of the Media player when there is announcement from the navigation voice guidance This function can be activated or deactivated by tapping on th
13. SYSTEM Long Long Long Long Long Press Press Press Press Press Open amp Close Audio System pes NM Up Volume Down MEL TM __ 1 1 Fast Fast Fast Up Forward Forward Forward Tune Fast Fast Fast Down Backward Backward Backward awo pj te gp re go CDL pL RID eI 2 __ ___ __ Down Down a EN 0 pe m m om a emm om 9 em m Remote Control Operations OOOO oO oo 2000000990000090 5 Oo m ooo s ooo 99 eccegoccece OOOO OPERATIONS SYSTEM TUNER CD MP3 WMA EM Short Long Short Long Long Short Long Press Press Press Press Press Press Press Memory Track NO Access 5 File NO Access Memory Track NO Access 6 File NO Access Track NO Access 25 ___ _ OO Track NO Access File NO Access Lu NO Access File NO Access Track NO Access E a Eie NO Access Numerico PE USERS onion NENNEN UR 32 Repeat NE cz mum CES _ 1 gt NEN Mode General Operations 4 96 5 3 Main Menu Media GPS CLE eo 1 2 7 8 1 Power On Off Button Long press the POWER button for more than 3 seconds or
14. button to play files in USB Inserting and Removing USB Drive Warning Never Detach the Panel when a Always remove the USB stick before detach Inserting the USB stick USB stick was plug on the socket the panel Mode change to USB MODE Under any other mode while inserting a USB Stick into the USB connector this unit will automatically switches from the current mode to USB mode Once the unit read the USB Stick successfully the first audio music file on the USB stick will automatically startto play Caution Before removing the USB stick from the USB connector Please always remember to switch off the unit s power or switch to other mode then unplug the USB Stick Never try to remove the USB Stick while playing music file on the USB stick may damage the USB Stick and sometimes will caused the unit system to lock up Note About Music Flash Player with USB Interface usually the unit takes longer time to read this kind of player than normal USB Stick Especially if the USB MP3 player is with built in power battery sometimes it may takes 20 30 seconds to start up the playback Navigation Operation What is GPS Navigation The term navigation is generally understood to mean the location of a vehicle the determination of the direction and distance from the desired destination and the required route As navigation aids stars prominent landmarks compass and sat ellites are used This unit location
15. from the satellites The position of satelites rela tive to your vehicle is bad
16. map inside the INTERNAL BUILT IN FLASH MEMORY Please refer to page Navigation Operation _ Digital Map for more details System Setting Operation System Information Tap button on the settings menu screen to view the detail system information including serial number of this unit The system information screen as follow These information may different from unit to unit System Information E OS Version 06 01 20 Processor SAMSUNG ARM 920T S3C2443 400MHz MemoryTotal 46752 KB RAM free 29988 KB Storage free 980 KB SW Version v01 03 00 08 07 08 RadioVersion v01 03 03 Serial Num System Setting Operation Upgrade Setting Tap button on the settings menu screen to access into the upgrade menu the below menu will appear Upgrade Settings E Map System Upgrade C Upgrade Note Insert SD card with the upgrade files stored before proceeding with the upgrade and then tap on desired upgrade feature button in Upgrade mode Map Upgrade Setting Tap button on the upgrade settings screen to access into the Map upgrade menu the below menu will appear Upgrade Settings 4a System Setting Operation Setting Control This Upgrade should only be performed te MAP by approved sevice center or techinal support from authorized dealer End user should never try to APP MAP the unit by themselves This Upgrade should only be performed TH APP
17. option or display a list of the options OSD language The OSD language setting provide the end user the selection of preferred language for the OSD menu and messages The following options are available i Language OIRE OSDLANG gt English 8 Audio 5 8 pisc Version OSD language setup English Media Player Subtitle The Subtitle setting allows the end user to select a preferred language and to change the subtitle language setup 1 Language 8 ospLANc 2 _______ cess pw Spanish French 8 visc gt Chinese e Version Others Off Subtitle language setup English Audio The Audio setting allows the user to select a preferred language and to change the Audio language setup Disc The Disc setting allows the user to select a preferred language and to change the Disc menu language setup Media Player 1 Language 8 ospLANG LETT I Audio English __________ Version French Chinese Others Automatic Disc menu language setup English Display Setting Press on the remote control or touch screen W buttons to move to the Display button The list of Display options will appear as follow 2 Display TV display le TV Type Angle mark Screen saver Use the buttons to select the setting Usethe YW buttons to change among the avaitable settings Press Ok or touch screen
18. short press any other button on the front of the panel except the Eject Open to turn on the unit Long press the POWER button for more than 3 seconds to turn Off the unit 1 Mute Button Short press the MUTE button less than 3 seconds to mute the audio output and Mute will appear on the screen Press the mute button again to resume the audio output to the previous level 2 Encoder Volume Button To increase the volume rotate the volume control knob clockwise To decrease the volume rotate the volume control knob counter clockwise When the volume is adjusted the volume level will be shown on the screen Tip The navigation voice guidance level is adjustable Please refer to page Navigation Operation Hightlight Features for more details 3 Eject Button Short press the EJECT buttonlessthan 3 seconds to ejectthe Disc General Operations 3 Panel Angle Adjustment End user can adjust the panel viewing angle of the display to obtain the optimum viewing angle inside the vehicle There are TWO angles can be adjusted by Long pressing the panel Eject Open button 1 1st long press to get into Angle 1 2 2nd long press to get into Angle 2 3 3rd long press to resume to the normal position 4 Panel Release Button Press this button to remove detach the control panel 5 Main Menu Screen Starts by displaying the Main Menu This is the root of the screen hierarchy and can simply access to all features by tapping on the touch sc
19. this is not used the reception sensitivity will be poor Do not cut the accessory metal sheet This would reduce the sensitivity of the GPS aerial Installing the GPS Antenna Aerial e care not to pull the antenna aerial lead when removing the GPS aerial The magnet attached to the aerial is very powerful and the lead may become detached The GPS antenna aerial is installed with a magnet When installing the GPS antena aerial be careful not to scratch the vehicle body When installing the GPS antenna aerial on the outside of the vehicle always put it in the vehicle when going through an automatic vehicle wash f it is left on the outside it may be knocked off and scratch the vehicle body Don t paint the GPS antenna aerial as this may affect its performance Note When attaching the metal sheet do not cut it into small pieces Some vehicles use window glass that does not allow signals from GPS satellites to pass through On such vehicles install the GPS antenna aerial on the outside of the vehicle When installing the aerial outside the vehicle on the body Put the GPS aerial in a position as level as possible such as on the roof or boot lid The GPS aerial is fastened with a magnet GPS antenna aerial Installation the Unit Before finally installing the unit connect the wiring temporarily and make sure it is all connected up properly and the unit and system work properly
20. try to detach remove the front panel by pressing the detach button or attach the front panel when the panel is in the slide down position This may cause serious amp permanent damage to the unit amp panel Only attach or detach the front panel when the panel is in the slide up position Overview the Unit Front panel main control Panel Eject Open Release IR Receiver Panel Angle adjust REL Volume Knob Touch Screen Display USB SD Card slot for MEDIA PLAYER Detach the Front Panel p A Insert the Memory 2 Card with Label up 25 side into the SD Ce Card slot on main unit Detach the Front Panel BE Mw 2 ard wi abel up side into the SD Card slot behind the front panel Resetting the unit After releasing the front panel use a pencil or any ET S non metalic object to press amp hold the reset button for five seconds to unit Disc Can Supports Discs can play with this unit No Content Digital Versatile Discs DVDs 2 Video CDs VCDs 3 Digital Versatile Discs Recordable DVD R ERES 4 Digital Versatile Discs Rewritable DVD RW x m 5 Compact Digital Video VCD cise Se DICITAL AUDIO 6 Compact Discs Cds 7 Recordable CD R 8 CD Rewritable CD RW Discs which can notbe played Note on region code 8cm Disc amp X DVD players and DVD CDV CDI Video discs have their own Region Code e L
21. D numbers This unit can e DVD RAM play the disc of all region code numbers Disc maintenance Before playing wipe the disc using a clean cloth working from the center hole towards the outside edge Never use benzene thinners cleaning luids or antistatic liquids or any other solvent Note A disc may become somewhat scratched although not enough to make it unusable depending on you handle it and conditions in the usage environment Note these scratches are not an indication of any problem with the player Label side Up bend Never touch the Wipe the disc under side of a surface from the diec center to the edge aL An 3 Formats Can Playback Audio format can playback Playback CD DA and MP3 or WMA digital music file on CD ROM or DVD ROM or USB Memory Note of MP3 and WMA e Support Maximum 2000 files e Maximum 30 characters display e Supported Sampling frequencies 32kHz 44 1kHz 48kHz e Supported Bit Rates MP3 8 320kbps variable bit rate WMA 32 192kbps variable bit rate Video format can playback Playback IMAGE JPEG DVD Video AVI MPEG4 on CD ROM or DVD ROM or USB or Memory Card Note of the MPEG4 e Supported decoding MPEG4 video defined by ISO 14496 2 Standard A Simple Profile SP B Advance Simple Profile ASP e Supported file format MP4 and M4A audio only Remote Control Operations OOOO OPERATIONS
22. MMN gt IMAGE View gt Slide In Slide mode when the key ENTE PLAY is pressed the player will show pictures or photos one by one from current picture It will stop and return back when the last one has been shown Press STOP button or tap touch screen button to stop the slide show mode NE amp 24 24 00000 amp IM010024 JPG 10001 mrs m 2PARTS 18 1 010018 E a THUM NEA Ee 20 IMO10020 JP 21 1 010021 22 1 010022 Fa 23 1 010023 fe 24 1 010024 JP MMN gt IMAGE View gt Rotate By using the Rotate function the picture or photo can be shown in different angle and press on remote control or tap touch screen A V lt gt key to switch among these angles Rotate angle A 0 P 90 W Rotate 180 lt q Rotate 270 EN NI TH Rotate 90 2 24 Media Player DVD Disc Operation 1 7 4 12 13 14 151617 18 9 NE m SET E 0 0 0 me R 23 6 8 2 7 10 11 Once a DVD disc is inserted into the unit the unit will automatically start the playback from the beginning of the disc and then the DVD MENU or ROOT or TITLE in the DVD disc will appear on the TFT monitor and ROOT will be displayed on the TFT of the unit Tip When the DVD Menu or Root or Title is show on the screen end user can use remote control or tap touch screen 4 7 x gt but
23. ON ys 1 Turn the Power off 2 2 Press the Panel Release Button prEP Remove the D F P 1 Insert the right side of the D F P Into the main unit Note The D F P Must be attached into the T Joint 2 Press the D F P on to the left side of middle of D F P until a clicK sound is heard Caution Do not insert the D F P from the left side Doing so may damage it The D F P can easily be damaged by shocks After removing it place it in a protective case and be careful not to drop it or subject it to strong shocks When the release button is pressed and the D F P is unlocked the cars vibrations may cause it to fall To prevent damage to the D F P always store it in a protective case after detaching It The rear connector that connects the main unit and the D F P is an extremely important part Be careful not to damage it by pressing onit with fingernails pens screwdrivers etc Note If the D F P is dirty wipe off the dirt with soft dry cloth only And use a cotton swab soaked in isopropyl alcohol to clean the socket on the back ofthe D F P Panel Open Close Operation The unit is equipped with the most advanced full logic motorized slide down system You can enjoy the advance technology with a single press of the Eject Open button Please read carefully the following operation instruction before operating the unit Open close the panel Press the Eject Open button to slide down
24. This unit ONLY CAN ACCEPT RUN those digital map purchased from authorized dealers agents Any non authorized digital map is CANNOT BE USED on this unit Navigation Operation Start Navigation Mode Caution For safety reasons you can not use some of navigation functions while your vehicle is in motion To enable these funcions you must stop in a safe place and apply the handbrake Park your vehicle in a safe place and apply the handbrake y How to get into the GPS Navigation system Please read the below instruction carefully before operating the unit 1 First power on the unit by pressing the POWER MUTE button 2 There are several ways to get into the GPS NAVIGATION MODE e When in the Tuner Radio mode end user can press on the button ON THE TOUCH SCREEN to get into the GPS NAVIGATION MODE F FM1 104 00 FMSELECT 10600 10800 8750 e When in Media Player mode CD DVD USB SD end user can tap on the touch screen to bring up the menu and then press on the button ON THE TOUCH SCREEN to get into the GPS NAVIGATION MODE Aft 1 Mi bil v Navigation Operation When in AV IN Mode end user can tab on the touch screen 3 N to bring up the menu and then press the NAVI button ON THE TOUCH SCREEN to get into the GPS NAVIGATION MODE NAVI 4 IJ
25. bient the car is too high temperature returns to normal Condensation Leave the player to off for an hour or so then try again Adjust volume to a desired level Wiring is not properly Check wiring connection connected The operation The built in microcomputer Press the RESET button keys do not work is not operating properly Front panel is not properly fixed into due to noise its place Sound skips The installation angle is Adjust the installation angle to less more than 30 degrees than 30 degrees The disc is extremely dirt Clean the compact disc Then try to ordefective disc play a new one The radio does The antenna cable is not Insert the antenna cable firmly not work connected SS Tan The signals are too weak Select a station manually does not work Press the eject button to correct the problem If the error code does not disappear consult your nearest service dealer Disc Error Maybe disc dirty disc You cannot The quality of signals from Check the GPS signal reception position Your the GPS satellites is poor and the position of the GPS aerial vehicle on the causing reduced positioning if necessary or continue driving until accuracy Such a loss of AR I apor the signal quality may happen reception improves Keep the aerial positioning error forthe following reasons Clear is large e The GPS aerial is in an unsuitable location e Obstacles are blocking sign als signals
26. by approved sevice center or techinal support from authorized dealer End user should never try to APP the unit by themselves This Map Upgrade is useful for end user d whenever there is a newest version of digital map released by the authorized dealers agents Note Map Upgrade is useful for end user whenever there is a newest version of digital map released by the authorized dealers agents and End User can upgrade the new digital map to the internal memory as the default map Before making the Map Upgrade please make sure this unit s internal memory size is big enough for loading the new digital map To check the internal memory size for digital map please referto section Navigation Operation Digital Map formore details Note This unit only can be upgraded thru the SD Card interface The SD card contained the upgrade data or digital map data must be inserted into the panel s SD Card slot Please refer to the Overview of the unit for more details of the SD card slot for upgrade purpose System Setting Operation System Upgrade Setting Tap button on the upgrade settings screen to access into the System upgrade menu the below menu will appear Note System Upgrade should only be performed by approved sevice center or techinal support from authorized dealer End user should never try to System Upgrade the unit by themselves Memory Operation 1 Press the MODE button repeatedly
27. ch screen gt I button when playing a disc a chapter DVD a track VCD SVCD CD a song WMA a picture JPEG or a video file AVI MPEG4 MPG DAT is skipped forward accordingly 8 PREV Function Pressing PREV button or tap touch screen M4 button will play the current chapter DVD current track VCD SVCD CD current song MP3 WMA or current video file AVI MPEGA MPG DAT from the beginning if the already played time is less than four seconds If already played time is more than four seconds Pressing PREV button will skip a chapter DVD a track VCD SVCD CD a song MP3 WMA a picture JPEG or a video file AVI MPEG4 MPG DAT backwardly 7 8 Fast Forward 4 Fast Back Forward Function e Long press FAST FORWARD or touch screen M for more than 3 seconds to fast forward through the disc Each time the button is pressed a new speed 2X 4X 8X or 16X will be activated e Press PLAY or touch screen button Jto resume normal playback e Long press FAST BACKWARD ortouch screen button 144 to fast reverse through the disc Each time the button is pressed a new speed 2X 4X 8X or 16X will be activated Press PLAY or touch screen button n to resume normal playback Number 0 9 On Remote Control By pressing the Number 0 1 2 3 4 5 6 7 8 9 button End user can access into the desired track or chapter Also it is widely used in different search domain title search cha
28. cle s wheels spin such as on a rough track or in snow If trees or other obstacles block the GPS sig nals for a considerable period If your vehicle is turned on a turntable or simi lar structure If you put on chains or change your tyres for ones with a different size If you drive very slowly or in a start and stop manner as in a traffic jam Navigation Operation e f you join the road after e When you go round a driving around a large roundabout car park Whenstarting driving immediately after start ing the engine fyouturn your navigation system on while driving oome types of vehicles may not output a speed signal while driving at just a few kilometres per hour In such a case the current location of your vehicle may not be displayed correctly while in a traffic jam or in a car park Navigation Operation Digital Map This unitis pre loaded with the below digital map marked with Yes inside the INTERNAL BUILT IN FLASH MEMORY Maps Pre Loaded Eastern Europe Western Europe Yes Yes Yes Yes Yes Yes Yes Yes Yes 6 0 0 Oo o Note End ser can purchase the authorized digital map and stored it into SD Memory Card This unit ONLY CAN RUN THE AUTHORIZED DIGITAL MAP PURCHASED FROM AUTHORIZED AGE NT OR DEALER on SD card Tips Please refer to page SETTING _ Run GPS Map for details on howto run the digital map on SD Card Note
29. croVision V122 English Espanol d 4 Francais Mode Caution In order to avoid any accident the driver must not watch video while driving This unit is designed to not allow watching moving video while driving Park your car in a safe place and engage the parking brake before watching moving video Note If watch moving video from Disc or AV In source but Parking Brake IS NOT PROPERLY CONNECTED the video signal will be blocked by the system and the below display will be shown on the unit display Reminder ideo Lock Engage Parking Brake to enjoy Video Select the AV mode 1 Press the MODE button repeatedly on panel or remote control to switch between Tuner gt Disc gt USB gt SD Card gt AV IN Mode 2 Aceess to MAIN MENU and tap AV Mode Tap the following buttons to start playing the desired media sources button to start the Navigation mode button to activale the Navigation Voice guide Button to set the color preference Button to quit the player System Setting Operation To adjust the system Settings of this unit tap on the main menu screen button to enter into the setting menu the below menu will appear Settings Ri i My 43 wes Info Display lt gt 6 GPS map Upgrade Sound Setting Tap button on setting menu screen to access into the sound setting menu the below menu will appear for selection Balance Fad
30. e screen button y Navigation Voice Guidance Volume level control The sound level of the navigation voice guidance can be adjusted by pressing the NAVI VOICE button and When display on screen there is around 10 seconds time out to adjust the desired sound level by rotating the encoder volume knob Tips This NAVI VOICE sound level adjustment will not affect the Tuner or Media Player volume level Tips Long pressing NAVI VOICE button to switch this NAVI VOICE guidance ON or OFF Y Switch TFT display mode between GPS Map to Media Player End user can switch the TFT display between the playback mode and GPS NAVIGATION MAP screen by following 1 Shortpressing the GPS MODE button on panel 2 Taping onthe touch screen button NAVI Media Player CD VCD Disc Operation NAVI SET e iy T IR EE ICE SUN E A Track File Press the TRACK FILE UP 7 TRACK FILE DOWN 8 button or touch screen 1 7 I44 8 for less than 1 second to move to the next or previous track on the CD The selected track number will appear on the screen Press and Hold TRACK UP 7 TRACK DOWN 8 button or touch screen bpl 7 8 for more than 1 second to fast forward or fast reverse through the disc Playback will resume when the button is released 1 Pause Play Fuction e Press PLAY PAUSE button or tap touch screen button Pill to start the playback of t
31. edia Player volume level Long pressing NAVI VOICE button to switch this NAVI VOICE guidance ON or OFF Tuner operations 4 2 96 3 5 Lo dL Cc lane nce e A 9g w 2 FM1 104 00 Bu FMSELECT p RM RM RM NM MM 1 Band Function Press panel BAND button or touch screen to change between FM bands and AM MW bands 2 amp 3 Tuning Up Down Manual Tuning Press amp Hold the panel UP DOWN Tuning button or tapping touch screen button to move the radio frequency number up or down by one step Auto Seek Tuning Press the panel UP DOWN Tuning button or tapping touch screen button I tomovetonextstation automatically 4 Preset Stations Press the panel 6 numbered preset buttons or tap touch screen button to store and recall stations for each band 5 Automatically store preset scan AS PS Automatically select 6 strongest stations and store them in the current band Long press panel AS PS button for more than 3 the new stations replace stations already stored in that and Preset Scan To Scan the stations already stored in the current band Short press panel AS PS button for less than 3 seconds the unit will for 10 seconds at each preset station Press panel AS PS utton again to stop scanning when the desired station is reached Tuner operations RDS Function The unit is equi
32. elect the Dual mono and set dual mono 1 1 setup stereo output of this Player Audio my Downmix Dualmono Stereo le Dynamic L mono R mono Mix mono Dual mono 1 1 setup Stereo The Audio setting allows the user to select the Dynamic and set the dynamic sound output high volume outputs are softened Media Player Parental Setting Press the or touch screen W buttons move to the Parental button The list of Parental optional will appear as follow Parental fal e Parent le Default Use the buttons to select the setting Usethe YW buttons to change among the avaitable settings Press Ok or touch screen to cycle through each possible option or display a list ofthe available options Change Password This feature is used for Parental Control Enter your four digit password when a hint is displayed on the screen Media Player Parental Change password Once entered the wrong password the Wrong Password message will appear i Parental e i e Change Change Parent Default Change password To re enter the correct password end user need to move to Enter Password again and try again Once entered the correct password press OK or touch screen and the correct password message will appear Media Player Parental T Change Parent E petaun Change password
33. er Treble Setting Control m Left and Right Speaker Balance Fader Front and Rear Speaker Fader Bass Level Treble Level Treble System Setting Operation Tap level button on the sound setting menu screen to select the Tap button to enter the next page the below menu will appear for selection Sound Setting E Sub Woofer Output Note Tap button to be return to the previous page Setting Control ERG Beep Tone ERG Sub Woofer Output Tap EN bar on the sound setting menu screen to turn on or off ofthese functions Tip Tap button to exit the sound setting menu System Setting Operation Display Setting Tap button on the setting menu screen to access into the Display setting menu the below menu will appear Setting Control Screen Brightness Tap AL button on the Display Setting menu screen to select the level Date amp Time Setting E on the Display Setting menu screen to access into the Date amp Time menu the below menu will appear Date amp Time Setting E Year Month Day on Hour Min Time FF TT 11 31 P Format 12 Hour Mode Tap button to select the Year Month Day of the Date mode and Hour Min of the Time mode then tap E button to change the date amp time System Setting Operation Tap bar to change time format to 24 hours Calibration Tap bar o
34. f signals cannot be received from more than two GPS satellites GPS positioning does nottake place In some driving conditions signals from GPS satellites may not reach your vehicle In this case it is impossible for the system to use GPS positioning The following are some examples 4 In tunnels or Under elevated enclosed parking garages roads or similar structures a WE a When driving When driving through among high buildings a dense forest or tall trees Navigation Operation Conditions Likely to Cause Noticeable Positioning Errors For various reasons such as the state of the road you are travelling on and the state of reception of the GPS signal the actual position of your vehicle may differ from the position displayed on the map screen e f you make a slight turn e f there is a parallel road f there is another road f you take a recently very nearby such as in opened road that is not the case of an elevated on the map motorway Navigation Operation f you drive in zig zags e f the road has connected hairpin bends e fthere is a loop or similar f you take a ferry road configuration f you are driving on a long If you are on a steep straight road or a gently mountain road with many curving road height changes Navigation Operation f you enter or exit a multi storey car park or similar using a spiral ramp If your vehi
35. he disc During title menu root menu pause resume stop stop slow forward fast forward fast backward mode Press PLAY PAUSE button or tap touch screen button 1 Jto pause the playback Press PLAY PAUSE again to resume the playback Media Player 2 Stop Function Press STOP button or tap touch screen button to stop pla ying When playback is stopped the unit can keep the memory of where the STOP was pressed Press PLAY and the playback will resume from this point Press STOP button again RESUME function will be cancelled and the unit is now in full stop mode If PLAY button is pressed now it will play from the beginning RESUME function is suitable for discs showing playing time during playback Press STOP twice state changes play gt resume stop gt full stop 3 Repeat Function Press REPEAT button during playback to activate the repeat play function e CD Repeat Press REPEAT state changes repeat all gt repeat track e VCD SVCD Repeat Short press REPEAT state changes repeat off gt repeat track Long press REPEAT state changes repeat off gt repeat all 4 Random function e Normal Random on repeat default e Random gt Normal on repeat default 7 amp 8 Fast Forward Fast Reverse Press FAST FORWARD FAST REVERSE button during play back the disc will fast forward or backward in different times of normal playing speed There are 5 levels of speed available X2 X4 X8 X16 X32 mea
36. ion of the GPS NAVIGATION SYSTEM of this unit please refer to the GPS NAVIGATION SYSTEM USER MANUAL provided together with this unit Tips End user can switch to GPS NAVIGATION MODE or GPS MAP SCREEN at any time in any mode by pressing the GPS MODE button on the front panel And pressing this GPS MODE button to switch back to the previous mode Tips End user can turn on or off the GPS NAVIGATION VOICE GUIDE by pressing the NAVI VOICE button on the front panel Once this NAVI VOICE GUIDE is turned on whenever there is any NAVI VOICE GUIDE the current mode s audio output will be cut and switch to the NAVI VOICE GUIDE then switch back to the current mode s audio output Navigation Operation Highlight Features The following are the highlight navigation features Y Navigation Voice Guidance under Tuner or Media Player playback During the navigation mode music of Tuner or Media player can still be heard This unit will automacitally MUTE the music of tuner or Media player when there is announcement from the navigation voice guidance This function can be activate or deactivate by Long pressing the NAVI VOICE button on panel Tapping on the touch screen buttons 1 Under Tuner Mode tap the screen EFAS 2 Under Media player or AV in mode tap the screen 9 Navigation Voice Guidance Volume level control The sound level of the navigation voice guidance is EI by press the NAVI VOICE button a
37. is determined with the GPS receiver GPS Global Positioning System The direction and distance from the destination are determined by using a digital road map a navigation computer and sensors A speedometer signal and a reverse signal are additionally used to calculate the route What is GPS The Global Positioning System GPS uses a network of satellites orbiting the Earth Each of the satellites which orbit at a height of 68 900 000 feet 21 000 km continually broadcasts radio signals giving time and position information This ensures that signals from at least three can be picked up from any open area on the earth s surface The accuracy of the GPS information depends on how good the reception is When the signals are strong and reception is good GPS can determine latitude longitude and altitude for accurate positioning in three dimensions But if signal quality is poor only two dimensions latitude and longitude can be obtained and positioning errors are somewhat greater OC Ej on C 6 7 MN u ki ANTES Jt amp YS Navigation Operation To receive GPS signals successfully e You have a clear sight of sky e The GPS antenna is not covered e The weather is good enough GPS signal is weaker in bad weather conditions e The time needed for establishing a GPS connection ranges from seconds to minutes You are outdoor When the positioning by GPS is impossible I
38. n the Display Setting menu screen to start the Calibration setting Carefully press and briefly hold stylus on the center of the target Repeat as the target moves around the screen When the target moves to another position tap and hold at the center of the new target Repeat each time to complete the calibration process Once completed tap anywhere on screen to go back to menu screen Note This Calibration is for the display touch screen If found the touch screen buttons sensitive became low the re calibration 15 necessary System Setting Operation Tuner Setting Radio Tap button on setting menu screen to access into the Tuner Radio setting menu the below menu will appear Tuner Setting EJ Seeking Mode Local Tuner Area Setting Control Seeking Mode Change Tuner seeking in Local or Local Distant mode Local Set the unit to select only strong local stations during automatic tuning Distant Allowing the radio to stop at a broader range of signals Tuner Area Change Tuner Frequency Area Europe gt USA Asia gt Latin America Note End user should make sure to select the Tuner Frequency Area which is correct for his area region Otherwise radio will not perform correctly Tap EH button to change the setting System Setting Operation GPS Map Setting This setting is for end user to select for run the digital Map which is stored into SD memory card o
39. nd When display on screen there is around 10 seconds time out to the desired sound level by rotating the encoder volume knob Tips This sound level adjustment will not affect the Tuner or Media Player volume level Tips Long pressing NAVI VOICE button can switch this voice guidance ON or OFF Y Switch TFT display mode from GPS Map to Tuner or Media Player By short pressing the GPS MODE button on panel By tapping on the touch screen buttons 1 Under Tuner Mode tap screen 2 Under Media player or AV in mode tap screen Nav Specification General Operating Voltage Grounding System Fuse Operating Temperature Unit Mounting Angle TFT Screen DC 11 14 4V Negative Ground 15 Amp Mini ATM Type 0 01050 lt 30 ocreen Size 3 5 Measured Diagonally ocreen Type TFT Liquid Crystal Display active matrix Resolution 960 W x 324 H Radio FM Frequency Range Usable Sensitivity Stereo Separation S N Ratio AM or MW Frequency Range Usable Sensitivity S N Ratio 87 5 108 0 MHz 50 kHz Space lt 15dB at S N 30 dB 25 dB at 1KHz 50 dB 022 1620 Khz 9 kHz Space 40dB at S N 20dB 40 dB Specification Media Player DVD CD Compatible Disc Format See Disc Note for more details description oignal to Noise Ratio gt 90 dB Dynamic Range gt 90 Frequency Response 20Hz to 20Khz 3dB Channel Separation 2 Channel Stereo
40. ns multiply with the normal speed To return back to normal play while in FAST FORWARD or FAST BACKWARD mode just press PLAY button on the panel or the remote control Press FAST FORWARD speed changes normal speed X2 gt X4 gt X8 gt X16 gt X32 gt normal speed Press FAST REVERSE speed changes normal speed X2 gt X4 gt X8 gt X16 X32 normal speed Media Player PBC On remote control Press PBC button on remote control to choose a VCD disc play mode PBC_ON or PBC_OFF when you playing a VCD disc When pressing PBC button and the player change to PBC _ON playing mode a PBC list of the disc will be displayed on TV or monitor In PBC list use number button to select a track to play or direction press PLAY button to start to the playback OSD VCD SVCD CD OSD information item Press OSD state change 1 OSD gt 2 OSD gt 3 OSD gt OSD off 1 050 CIIM 27 2 osD AT 60 00 23 0 39 17 3 OSD Track Time 0 00 25 0 0136 2nd OSD Disc Time 3rd OSD Current Track Time PBC Remain Track Time Play Mode L R Stereo Current Disc Time Media Player Music Image Video File Playback Operation The following display information will appear Multi Media disc or USB or SD is inserted into this unit 1 7 A g File Info Playi statue domain domain 2 songs MCI 795 23 8 Folder Image browse File
41. on panel or remote control to switch between Tuner gt Disc gt USB gt SD Card gt AV IN Media 2 Aceess to MAIN MENU and tap Tul z 2 MEDIA PLAYER Tap the following buttons to start the playback of the desired media sources M Button to play the files in SD card Note Please read below before you start the operation of Memory Card Inserting SD or MMC card on the main unit Detach the Insert the Memory Card Push in till heard a click Front Panel with Label up side Removing the SD or MMC card on the main unit Detach the Push in till heard a click Remove the Memory Card Front Panel Mode change to MEMORY CARD MODE After a SD or MMC card was inserted into the main unit card slot Press panel Mode button or tap touch screen BJ to select card mode The unit will starts playing the files contained on the Memory Card Once the unit read the Memory Card successfully the first file on the Memory Card will automatically start to play Note If no any Memory is inserted into the main unit card slot Pressing the mode button will automatically skip the SD card mode USB Operation 1 Press the MODE button repeatedly on panel or remote control to switch between Tuner Disc gt USB gt SD Card gt AV IN Mode 2 Aceess to MAIN MENU and tap 2 MEDIA PLAYER Tap the following buttons to start playing the desired media sources
42. pped with the following RDS function AF Alternative Frequencies CT Clock Time PI Program identifications PS Program service name PTY Program Type REG Regional Change TA Traffic Announcement Traffic program 6 AF function Short pressing panel AF button less than 3 seconds to select AF ON OFF AF icon will light up on the screen Under AF mode if the tuned in station signal is getting weak the unit will automatically switches to a different frequency on the same network with stronger signal Note Factory default setting is AF ON 8 TAFunction Short pressing panel GPS MODE TA button less than 3 seconds to switch on TA standby mode The icon will light up on the screen In the stand by mode when a traffic announcement broadcast starts the traffic announcement broadcast will be received as top priority regardless of the function mode When a traffic announcement starts TRAFFIC INFO will show on the screen press the button can cancelled the broadcast reception while a traffic announcement broadcast is being received The unit will go back to the previous mode and TA goes into stand by mode again Tuner operations 7 PTY Function Long press the SUB W PTY button for more than 3 seconds to set into the PTY mode And then press this button repeatedly to different PTY group as listed below Once the desired PTY is shown on the preset memory M1 to M6 press this p
43. pport Strap Be sure to use the support strap to secure the back of the unit in place The strap can be bent by hand to the desired angle T Plain washer By Removing the unit No Content 1 Frame 2 Insert fingers into the groove in the front of frame and pull out to remove the frame When re attaching the frame point the side with a groove down wards and attach it 3 Insert the levers supplied with the unit into the grooves at both sides of the unit as shown in figure until they click Pulling the levers makes it possible to remove the unit from the dashboard Installation the Unit Trim Plate Installation Push the trim plate against the chassis until it is fitted You must do this before you install the front panel otherwise it can t be attached Din rear mount method B Installation using the screw holes on the sides ofthe unit Fastening the unitto the factory radio mounting bracket No 1 gt OJN Content Select a position where the screw holes of the bracket and the screw holes of the main unit become aligned are fitted and tighten the screws at 2 places on each side Screw Factory radio mounting bracket Dashboard or Console Hook Remove this part jJ Note The mounting box outer trim ring and half sleeve are not used for method B installation Detachable Front Panel D F P Removing the detachable front panel D F P BUTT
44. pter search track search time search and program function Media Player Subtitle On Remote Control Pressing the SUBTITLE button on remote control End user may select one of the subtitles language to show it on the screen or to turn off the SUBTITLE This function is invalid for VCD SVCD WMA and JPEG Subtitle 01 02 English 9 DVDOSD D e Short Press AS PS button once to display the amount of time played and time remaining on the disc e Short Press AS PS button twice to display the disc type current chapter DVD or track VCD SVCD Audio CD and total number of chapters or tracks Also displayed for DVD only the current title total number of titles audio language type of channels subtitle language and angle selection 9 DVDSetUp D Press the SET UP button on the remote control or long press the AS PS button for more than 3 seconds on the main unit to enter into the Setup Menu mode The options included in General Setup menu are Language Display Audio Parental Media Player Language Setting Press the or touch screen W buttons move to the Language button Thelistof available language will appear Language 6 ospLanc 8 8 Audio Disc Version Use the buttons to select the setting Usethe VW buttons to change among the available language Press Ok or touch screen lt to cycle through each possible
45. r in the built in internal memory Tap button on setting menu screen to access into the GPS Map setting the below menu will appear GPS MAP Setting E Run GPS Map on Internal Memory Run GPS Map on SD Card Setting Control Run GPS Map on Internal Memory Select to run Digital Map on internal memory Run GPS Map on Select to run Digital Map on SD memory card Important To activates run the Digital Map on the SD Card End user must switch off the GPS Navigation Access to GPS Navigation Main Cudle x Menu and tap to switch off EXE SD Card the GPS Navigation After switched off the GPS Navigation end user then tap geen _____ SD Map O About a205 AJP Find amp Go This time re entry to GPS Navigation the system is automatic run the Map which stored on SD Card Exit dd as the confirmation of the selection System Setting Operation Note End user can purchase the authorized digital map and Store it into SD Memory Card Note This unit ONLY CAN ACCEPT RUN those digital map purchased from authorized dealers agents Any non authorized digital map CANNOT BE USED on this unit Note This unit only can run the SD Card contained with digital map which is inserted into the panel s SD card slot Please refer to the page Overview of the unit for more details of the SD card slot for Digital Map use Note This unit is pre loaded with digital
46. reen button the below menu will be appear Media i Player p Setting Button Control Access into GPS Navigation Access into Media Player mode Access into Tuner mode LIS Access into AV In mode Enter into the Setting menu 6 Loud Button Short press the Loud button for less than 3 seconds to select the Loud On to increase bass output the default is Off General Operations 7 Sub woofer Short press the SUB W button for less than 3 seconds to turn on the Sub woofer function Press the SUB W button again to turn off the Sub woofer function 8 GPS Mode End user can switch the TFT display between the playback mode and GPS NAVIGATION MAP screen by following 1 Shortpressingthe GPS MODE button on panel FEPER 90 00 106 00 108 00 87 50 9 Navi Voice This unit will automacitally MUTE the audio output of the Media player when there is announcement from the navigation voice guidance This function can be activated or deactivated by tapping on the screen Or VOICE The sound level of the Davison et voice guidance can be adjus can be by pressing the NAVI VOICE button and When J display on screen there is around 10 seconds Es out to adjust the desired sound level by rotating the encoder volume knob Button Control Navigation Voice guide on Navigation Voice guide off Tips This NAVI VOICE sound level adjustment will not affect the Tuner or M
47. reset memory number to activate the searching of this PTY the PTY name will appear onthe6 preset buttons LIGHT M CLASSICS OTHER M SPORT EDUCATE DRAMA GROUP 1 GROUP 2 CULTURE SCIENCE VARIED SOCIAL RELIGION PHONE WEATHER FINANCE CHILDREN TRAVEL LEISURE DOCUMENT GROUP 3 GROUP 4 EE COUNTRY NATION M OLDIES FOLK M rw GROUP 5 If no station with the selected PTY broadcast can be found for 5 seconds the system then returns to the previous mode Media Player This Multi Media player unit can support the playback of CD Disc DVD disc USB Host SD Memory Card Note For more details of this unit supporting playback disc and format Please see pages of Disc Can support amp Format can playback Caution In order to avoid any accident the driver must not watch video while driving This unit is designed to not allow watching moving video while driving Park your car in a safe place and engage the parking brake before watching moving video Note If watch moving video from Disc or AV In source but Parking Brake IS NOT PROPERLY CONNECTED the video signal will be blocked by the system and the below display will be shown on the unit display Reminder Video Lock Engage Parking Brake to enjoy Video Select the Media Soruces for playing 1 Press the MODE button repeatedly on panel or remote control to switch between Tuner gt Disc gt USB gt SD Card gt AV
48. the window Place the GPS antenna aerial on the metal sheet The GPS antenna aerial is fastened with its magnet Metal Sheet GPS anteanna aerial Peel off the protective sheet on the rear Make sure the surface is free of moisture dust grime oil etc before affixing the metal sheet Note The metal sheet contains a strong adhesive which may leave a mark on the surface if it is removed Clamps Use clamps to secure the lead where necessary inside the vehicle Installing the GPS Antenna Aerial End user must read this section before installing the GPS Antenna Aerial Caution Do not cut the GPS antenna aerial lead to shorten it or use an extension to make it longer Altering the aerial cable could result in a short circuit or malfunction and permanent damage to the navigation system Connecting the Sag Antenna Aerial to the unit GPS AERIAL Note Always use the provided screw to fasten the GPS Antenna Aerial Installation Notes e The aerial should be installed on a level surface where radio waves Will be blocked as little as possible Radio waves cannot be received by the antenna aerial if reception from the satellite is blocked Installation on the vehicle roof or boot lid is recommended to optimism reception Roof Rear shelf e When installing the GPS antenna aerial inside the vehicle be sure to use the metal sheet provided with your system If
49. to follow this may cause malfunction or permanent damage due to the precise mechanism of this unit Incorrect installation may result in damage to the unit or to the vehicle Specialist knowledge and skills are required to install the unit and its components We strongly recommend that you have the unit installed by a specialist workshop Risk of injury Installing the components incorrectly may lead to injuries in the event of a road traffic accident or render safety devices ineffective Please refer to the instructions provided by the vehicle manufacturer Connecting the System Important notes Do not route wires where they will be exposed to high temperatures If the insulation heats up wires may become damaged resulting in a short circuit or malfunction and permanent damage to the navigation system Do not cut the GPS aerial cable to shorten it or use an extension to make it longer Altering the aerial cable could result in a short circuit or malfunction Do not shorten any leads If you do the protection circuit fuse holder fuse resister or filter etc may fail to work properly Never feed power to other electronic products by cutting the insulation of the power supply lead of the navigation system and tapping into the lead The current capacity of the lead will be exceeded causing overheating The black lead is earth Please earth this lead separately from the earth of high current products such as power amps Do not
50. ton to move the cursor and the button as OK button 1 Play Pause Function e Press PAUSE or touch screen Il to pause playback e Press PAUSE or touch screen n to single step forward to the next picture in the video DVD and VCD only Press PLAY or touch screen to resume normal playback Media Player 2 Stop Function e Press STOP or touch screen button to stop playback and show the logo screen The player will memorize the last position where playback is stopped Press PLAY or touch screen Coy to resume playback from the positon where playback is stopped DVD VCD 1 1 VCD 2 0 and audio CD e Pressing STOP twice or touch screen 8 to resume playback from the beginning of the disc 3 Repeat Function Short press REPEAT button less than 3 seconds to change from repeat off gt repeat chapter Long press REPEAT button more than 3 seconds to change from repeat off gt repeat title 4 DVD Menu Press DVD MENU button less than 3 seconds to bring up the DVD MENU or ROOT on the DVD disc Tip When the DVD Menu or Root or Title is show on the screen end user can use remote control or tap touch screen 4 x gt button to move the cursor and the button as OK button 5 DVD Audio Press DVD AUDIO you can choose audio streams if the DVD disc or AVI MPEGA has multi audio streams Audio 2 2 AC32CHEnglish AES Media Player 7 Next Function Press NEXT button or tap tou
Download Pdf Manuals
Related Search