Moxa TCF-142-M-SC-RM
Contents
1. TCF 142 ST a o O O s o EN ERA RAR AAA SB A 8 98 ATTENTION Electrostatic Discharge Warning To protect the product from damage due to electrostatic dead discharge we recommend wearing a grounding device when handling your TCF 142 RM slide in modules module series Pin Assignment and Connector 9 pin D sub Female 5 1 TER 9 6 Pin RS 232 RS 422 485 4w RS 485 2W 1 DCD RxD A Data A 2 TxD RxD B Data B 3 RxD TxD B z 4 DSR TxD A 5 GND GND GND 6 DTR 7 CTS 8 RTS 7 9 5 z Fiber Cable SC Port Pinouts SC Port to SC Port Cable Wiring A A HE ir core Tx EL tr B B H Cable Wiring Rx A A ST Port to ST Port Cable Wiring A i Se rs B Cable Wiring A B ATTENTION This is a Class 1 Laser LED product Do not stare into the Laser Beam Switch Settings There are 2 sets of DIP switches on the board One set for fiber and another for the connector Following are the settings for the 4 connector DIP switches Serial Connection Switch 1 Switch 2 RS 232 ON default ON default RS 422 ON OFF 2 wire RS 485 OFF ON 4 wire RS 485 OFF OFF 120Q Terminator Switch 3 En2. slide in module can be hot swapped which means the chassis doesn t have to power off or be removed during installation Align the slide in module with the chassis installation slot so that the panel fastener screw is at the top of the module Carefully slide the slide in module into the slot while aligning the module s circuit board with the installation guide Ensure the slide in module is firmly seated inside the chassis Push in and rotate the attached panel fastener screw clockwise to secure the module to the chassis Features e Ring or Point to Point transmission e Extend RS 232 422 485 transmission distance gt up to 40 km with single mode TCF 142 S XX RM slide in modules series gt up to 5 km with multi mode TCF 142 M XX RM slide in modules series Slide in modules of NRack system e Decrease signal interference e Protect against electrical degradation and chemical corrosion Support baudrate up to 921 6 Kbps Package Checklist Before installing the TCF 142 RM slide in module verify that the package contains the following items e TCF 142 RM slide in module Fiber Converter e Quick Installation Guide e Warranty Card NOTE Please notify your sales representative if any of the above items are missing or damaged Mounting Dimensions Unit mm TCF 142 SC An T KO O a BAAR AAA ASAS ASAS FEAR 898 124 3 129 3
3. TCF 142 RM Series Hardware Installation Guide Second Edition May 2010 MOXA 2010 Moxa Inc All rights reserved Reproduction without permission is prohibited F1 4 No 135 Lane 235 Pao Chiao Rd Shing Tien City Taipei Taiwan R O C TEL 886 2 8919 1230 P N 1802001420621 Overview Introduction The TCF 142 RM series fiber converters are slide in modules that can be installed in the NRack System s rackmount chassis such as the TRC 190 series The slide in module is equipped with a multiple interface circuit that can handle RS 232 or RS 422 485 serial interfaces and multi mode or single mode fiber The TCF 142 RM series slide in modules are used to extend serial transmission distance up to 5 km TCF 142 M XX RM with multi mode fiber or up to 40 km TCF 142 S XX RM with single mode fiber Why Convert Serial to Fiber Fiber communication not only extends the communication distance but also provides many advantageous features IMMUNITY FROM ELECTRICAL INTERFERENCE Fiber is not affected by electromagnetic interference or radio frequency interference It provides a clean communication path and is immune to cross talk INSULATION Optical fiber is an insulator the glass fiber eliminates the need for using electric currents as the communication medium SECURITY Fiber cannot be tapped by conventional electric means and is very difficult to tap into optically Furthermore radio and satellite communication signals c
4. able ON Disable OFF default Fiber Mode Switch 4 Ring Mode ON Point to Point Mode OFF default ATTENTION For Fiber Ring Users Before you plug the slide in module into the chassis make sure the DIP switch settings are correct before inserting the slide in module into the chassis and connecting the serial and fiber cables If the Rx LEDs of the converter glow continuously remove the fiber cable and reconnect NOTE Ring Mode can only be used for half duplex applications Following are the settings for the 2 fiber DIP switches Switch Pull Low Switch 2 Pull High 150KQ OFF OFF 1KQ ON Default ON Default LED Indicators There are 3 LEDs on the front bracket of the TCF 142 RM slide in modules LED Color Function PWR Green Steady ON Power is ON Fiber Tx Green When sending serial data from the fiber port Fiber Rx Yellow When receiving data from the fiber port Specifications Serial Communication Signals for RS 232 Signals for RS 422 Signals for 4 wire RS 485 Signals for 2 wire RS 485 Baudrate ESD protection Fiber Communication Connector type Distance Support Cable Wavelength TX Output RX Sensitivity Point to Point Transmission Multi drop Transmission Environmental Operating Temperature Storage Temperature Power Input Power Voltage Power Consumption Mechanical Dimensions W x D x H Material Gross Weight Reg
5. an be captured easily for decoding RELIABILITY amp MAINTENANCE Fiber is immune to adverse temperature and moisture conditions does not corrode or lose its signal and is not affected by short circuits power surges or static electricity No Configuration Required for Baudrate Settings The TCF 142 RM slide in modules work under any baudrate from 50 bps to 921 6 Kbps The TCF 142 RM slide in modules simply convert the signal back and forth between serial RS 232 RS 422 or RS 485 and fiber and since the TCF 142 RM slide in modules do not need to interpret the signal it does not need to know the baudrate of the transmitting device For this reason the TCF 142 RM slide in modules do not have any DIP switches or jumpers for setting the baudrate Ring Mode To allow one half duplex serial device to communicate with multiple half duplex devices connected to a fiber ring you should configure the TCF 142 RM slide in modules for ring mode by setting DIP switch SW3 to the On position The Tx port of a particular TCF 142 RM slide in modules unit connects to the neighboring converter s Rx port to form the ring Note that when one node transmits a signal the signal travels around the ring until it returns to the transmitting unit which then blocks the signal Users should ensure that the total fiber ring length is less than 100 km when using either single mode models or multi mode models Installation The media converter
6. ulatory Approvals CE FCC EMS Free fall TxD RxD SGND TxD TxD RxD RxD SGND TxD TxD RxD RxD SGND Data Data SGND 50 bps to 921 6 Kbps 15 KV ESD ST or SC Single mode fiber for 40 km Multi mode fiber for 5 km 8 3 125 8 7 125 9 125 or 10 125 um single mode 50 125 62 5 125 or 100 140 um multimode Single mode 1310 nm Multimode 850 nm Single mode gt 5 dBm Multimode gt 5 dBm Single mode 25 dBm Multimode 20 dBm Half or Full duplex Half duplex fiber ring 0 to 60 C 32 to 142 F 5 to 95 RH 20 to 75 C 4 to 185 F 5 to 95 RH 12 VDC 150 mA 12V 86 8 136 46 21mm SPCC 80g Class B Part 15 sub part B Class A EN61000 4 2 ESD Criteria B Level 4 EN61000 4 3 RS Criteria A Level 2 EN61000 4 4 EFT Criteria B Level 3 EN61000 4 5 Surge Criteria A Level 3 EN61000 4 6 CS Criteria A Level 2 En61000 4 8 PFMF Criteria A Level 3 IEC 60068 2 32 Technical Support Contact Information Www moxa com support Moxa Americas Toll free 1 888 669 2872 Tel 1 714 528 6777 Fax 1 714 528 6778 Moxa Europe Tel 49 89 3 70 03 99 0 Fax 49 89 3 70 03 99 99 Moxa China Shanghai office Toll free 800 820 5036 Tel 86 21 5258 9955 Fax 86 21 5258 5505 Moxa Asia Pacific Tel 886 2 8919 1230 Fax 886 2 8919 1231 9
Download Pdf Manuals
Related Search