Moxa CP-114EL
Contents
1. Click the sign next to Multi port serial adapters right click on MOXA CP 114EL Series PCI Express Bus select Properties then choose Port Configuration Click the port to configure Interface RS 232 RS 422 2 wire RS 485 4 wire RS 485 and Termination Resistor 120Q Enable or Disable If there are warning marks such as a question mark or exclamation point in front of the board or port icons examine the Event Log to determine the problem Linux Driver Installation 1 Execute the following commands from the Linux prompt mount dev cdrom mnt cdrom cd mkdir moxa cd moxa cp mnt cdrom lt driver directory gt driv_linux_smart_vx x_build_yymmddhh tgz tar xzvf driv_linux_smart_vx x_build_yymmddhh tgz 2 cd mxser make clean make install 3 cd moxa mxser driver msmknod 4 modprobe mxupcie 5 Use the Moxa Port Configuration Tool to set Interface and Termination Resistor for the MUE series The MUE series includes CP 102E CP 102EL CP 132EL CP 132EL I CP 114EL and CP 114EL I Usage muestty lt operation gt device Device The MUE series device node Operation h Help g Get interface and terminator type i intf Set interface type with options below t value Set termination resistor with options below intf RS232 RS 232 mode RS422 RS 422 mode RS4852W RS 485 2 wire mode RS4854W RS 485 4 wire mode value NONTERM Non termination resistor 120TERM 120ohm termination resistor For example2. To set the MUE interface muestty i RS422 dev ttyMUE2 To set the MUE termination resistor muestty t 120TERM dev ttyMUE2 6 Use the Moxa diagnostic utility to verify the driver status cd moxa mxser utility diag msdiag 7 Use the Moxa terminal utility to test the tty ports cd moxa mxser utility term msterm 5 Pin Assignments The CP 114EL and CP 114EL I boards come equipped with a female DB44 connector Cables with different connectors are available to help you connect your device to the board Male DB9 Device side Pin Assignments CBL M44M9x4 50 Male DB9 1 5 b Ga 4 6 9 pin RS 232 RS 422 amp 2 wire RS 485 p 4 wire RS 485 1 DCD TxD A 2 RxD TxD B e 3 TxD RxD B Data B 4 DTR RxD A Data A 5 GND GND GND 6 DSR 4 7 RTS Z 8 CTS 9 e Male DB25 Device side Pin Assignments CBL M44M25x4 50 Male DB25 13 14 25 Pin RS 232 RS 422 amp 2 wire RS 485 4 wire RS 485 2 TxD RxD B Data B 3 RxD TxD B 4 RTS 5 CTS 6 DSR i GND GND GND 8 DCD TxD A 20 DTR RxD A Data A 22 6 Specifications Hardware Connectors Female DB44 Comm Controller 16C550C compatible Interface Bus Interface PCI Express x 1 Number of Ports 4 Max No of Boards 4 Signal RS 232 TxD R
3. MOXA CP 114EL CP 114EL I PCI Express Multiport Serial Board Quick Installation Guide First Edition July 2008 1 Overview Moxa s new CP 114EL and CP 114EL I PCI Express multiport serial boards are designed for POS and ATM applications and for use by industrial automation system manufacturers and system integrators The boards are compatible with all popular operating systems Each board also supports data rates of up to 921 6Kbps and provides full modem control signals ensuring compatibility with a wide range of serial peripherals In addition the CP 114EL and CP 114EL I work with PCI Express x1 allowing the boards to be installed in any available PCI Express slot including x1 x2 x4 x8 x16 and x32 2 Package Checklist Before installing the PCI Express board verify that the package contains the following items e 1 PCI Express serial board e Documentation and Software CD e Quick Installation Guide e Low Profile Bracket Notify your sales representative if any of the above items is missing or damaged 3 Hardware Installation Procedure The PCI Express board MUST be plugged into the PC before the driver is installed Follow these steps to install the board in the PC STEP 1 Power off the PC STEP 2 Plug the board firmly into an open PCI Express slot STEP3 Fasten the holding screw to fix the control board in place STEP 4 Connect the connection cable STEP5 Power on the PC the BIOS will automatically set
4. ick the sign next to Hardware and then check Multi port serial adapters and Ports COM amp LPT Click the sign next to Multi port serial adapters right click on Moxa CP 114EL Series PCI Express Bus select Properties then choose Port Configuration Click the port to configure Interface RS 232 RS 422 2 wire RS 485 4 wire RS 485 and Termination Resistor 120 Enable or Disable If there are warning marks such as a question mark or exclamation point in front of the board or port icons examine the Event Log to determine the problem Windows 2003 XP 32 bit 64 bit Driver Installation 1 After powering on your PC Windows 2003 XP will automatically detect the PCIe board 2 Insert the PCIe software CD in your CD ROM drive 3 Select Install from a list or specific location Advanced 4 After selecting Search for the best driver in these locations select the Include this location in the search and then click Browse If the system is a 32 bit x86 platform navigate to the CP 114EL Series Software Windows XP_2003 x86 folder on the CD if the system is 64 bit x64 platform navigate to the CP 114EL Series Software Windows XP_2003 x64 folder on the CD and then click Next to continue 5 Click Continue Anyway in response to any warnings that the 2 software has not passed Windows Logo testing 6 After the board has been installed the installation wizard will guide you through the port installation procedure star
5. the IRQ and I O address P N 1802001142330 4 Software Installation Information The board MUST be plugged in before installing the driver See the previous section for instructions on how to install the board in your PC Refer to the PCI Express Board User s Manual for detailed instructions on installing the drivers for this board NOTE The following procedure shows how to install the CP 114EL driver Windows 2008 Vista 32 bit 64 bit Driver Installation 1 After powering on your PC Windows 2008 will automatically detect the PCIe board 2 Insert the PCIe software CD in your CD ROM drive 3 Select Locate and install driver software recommended 4 After selecting Search for driver software in this location select the Include subfolders and then click Browse If the system is a 32 bit x86 platform navigate to the CP 114EL Series Software Windows 2008_Vista x86 folder on the CD if the system is 64 bit x64 platform navigate to the CP 114EL Series Software Windows 2008_Vista x64 folder on the CD and then click Next to continue 5 Click Install this driver software anyway in response to any warnings that the software has not passed Windows Logo testing 6 After the board has been installed the installation wizard will guide you through the port installation procedure Port installation procedure is complete when Port 0 has been set up 7 Use the Device Manager to check the installation of the board and ports Cl
6. ting with port 0 7 Use the Device Manager to check the installation of the board and ports Click the sign next to Hardware and then check Multi port serial adapters and Ports COM amp LPT Click the sign next to Multi port serial adapters right click on MOXA CP 114EL Series PCI Express Bus select Properties then choose Port Configuration Click the port to configure Interface RS 232 RS 422 2 wire RS 485 4 wire RS 485 and Termination Resistor 120Q Enable or Disable If there are warning marks such as a question mark or exclamation point in front of the board or port icons examine the Event Log to determine the problem Windows 2000 Driver Installation 1 After powering on your PC Windows 2000 will automatically detect the PCle board 2 Insert the PCIe software CD in your CD ROM drive Select Search for a suitable driver for my device recommended A9 Under Optional search location select specify a location Navigate to the CP 114EL Series Software Windows 2K folder on the software CD 5 Click Continue Anyway in response to any warnings that the software has not passed Windows Logo testing 6 After the board has been installed the installation wizard will guide you through the port installation procedure starting with port 0 7 Use the Device Manager to check the installation of the board and ports Click the sign next to Hardware and then check Multi port serial adapters and Ports COM amp LPT
7. xD RTS CTS DTR DSR DCD GND RS 422 TxD B TxD A RxD B RxD A GND RS 485 4 Wire RS 485 2 Wire Performance Baudrate Configuration Data Bits Stop Bits T O address IRQ Parity Flow Control Environment Operating Temperature Operating Humidity Storage Temperature ESD Protection TxD B TxD A RxD B RxD A GND Data B Data A GND 50 bps to 921 6 Kbps 5 6 7 8 1 1 5 2 BIOS assigned None Even Odd Space Mark RTS CTS XON XOFF 0 to 55 C 32 to 132 F 5 to 95 RH 20 to 85 C 4 to 185 F Embedded 15 KV ESD Protection 5 Optical Isolation Regulatory Approvals Warranty MOXN 2 KV only for CP 114EL I EN55022 EN55024 EN61000 3 2 EN61000 3 3 EN61000 6 2 IEC 61000 4 2 TEC 61000 4 3 IEC 61000 4 4 IEC 61000 4 5 TEC 61000 4 6 IEC 61000 4 8 IEC 61000 4 11 FCC Part 15 Class B 5 years Click here for online support www moxa com support The Americas Europe Asia Pacific China 1 714 528 6777 toll free 1 888 669 2872 49 89 3 70 03 99 0 886 2 8919 1230 86 21 5258 9955 toll free 800 820 5036 2008 Moxa Inc all rights reserved Reproduction without permission is prohibited 6
Download Pdf Manuals
Related Search