Saeco Syntia Super-automatic espresso machine HD8837/09
Contents
1. Jurnthe selector dial counter clockwise tosetit to the amp position Froth the milk by gently swirling the cup After dispensing steam for the desired time turn the selector dial clockwise and set it back to the position to stop dispensing steam e The same procedure can be used to heat other beverages After using the steam hot water wand Pannarello if supplied wash it as de scribed in the Cleaning and Maintenance section After using steam to prepare a beverage it is possible to brew coffee or to dispense steam straight after If the selector dial is left on the central position the machine in order to save energy au tomatically reaches the temperature needed to dispense coffee CLEANING AND MAINTENANCE General cleaning Empty and clean the dregdrawer daily with the machine turned on Maintenance and cleaning operations can only be carried out when the ma chine is cold and disconnected from the power supply Donot immerse the machine in water Do not wash any of its parts in the dishwasher Do not use sharp objects or harsh chemical products solvents for clean ing Usea soft dampened cloth to clean the machine Do not dry the machine and or its components using a microwave and or standard oven After frothing milk bever ages dispense hot water from the steam h2. Remove the dregdrawer Open the service door To remove the brew group pull it by the handle and press the PUSH button The brew group must be washed only with lukewarm water no detergent Soap is necessary Wash the brew group with lukewarm water and carefully clean the upper filter Thoroughly wash and dry all the parts of the brew group Thoroughly clean the inside of the machine Make sure that the brew group is in rest position The two references must match The lever on the rear part of the brew group must be in contact with the base Press the PUSH button to make sure that the brew group is in the correct position Lubricate the brew group af ter approximately 500 brew ing cycles The brew group lubricant may be purchased at authorized service centers Lubricate the brew group guides using the supplied lubricant only Apply the lubricant evenly on both side guides SJ Insert the brew group in its seat until it locks into place WITHOUT pressing the PUSH button Insert the dregdrawer Close the service door el7e DESCALING Limescale build up is normal with the use of this appliance The display informs you when descaling is necessary Only use the Saeco descaling solution It has been spe cifically developed to preserve perfor mance and functionality throughout the lifetime of
3. the wand and repeat the procedure After adding the descaling solution in the tank turn the selector dial clockwise to position 2 to start the descaling cycle The machine will start dispensing at regular intervals the descaling solution the bar shows the cycle progress O G Red e When the solution in the tank is finished dispensing the icon on the side is displayed to indicate that the selector dial must be brought back to the P position The icon indicates that the tank must be rinsed and filled Rinse the water tank thoroughly and refill it with fresh drinking water Empty the container used to collect the liquid dispensed by the machine and place it under the steam wand When inserting the tank filled with water in the machine the icon on the side is displayed turn the selector dial clockwise to position The machine starts the rinse cycle When the water in the tank is finished dispensing the icon on the side is displayed to indicate that the selector dial must be brought back to the position The icon indicates that the tank must be rinsed and filled Rinse the water tank thoroughly and refill it with fresh drinking water Empty the container used to collect the liquid dispensed by the machine and place it under the steam wand Red END Red fata When insert
4. If the machine is being used for the first time or after a long period of inactivity follow the operations described in the follow ing section Using the machine for the The following icon will be displayed 5 first time or after a long Wp period of inactivity These simple operations will make it pos Green sible to always brew excellent coffee l l 9 Dispense water until the no water sig 1 Place a large container under the nal is displayed then turn the selector dispensing spout switch counter clockwise to set it to the P position 2 Before starting the procedure check that the following icon is displayed 10 At the end fill the water tank again Then the products can be brewed as described in the following sections 3 Select the pre ground coffee function by pressing the o button one or more times 7 Do not add the pre ground coffee to the compartment Rinse Self Cleaning Cycle This cycle will rinse coffee circuits with fresh water The icon will appear on the display The cycle is carried out At machine start with cold boiler 4 Press the button to brew a long cof After priming the water circuit with fee cold boiler 5 Wait until brewing is completed and During the stand by mode if a coffee empty the water tank product has been brewed Ifthe machine is turned off by pressing the ON OFF button if a coffee product has been bre
5. ences Large Dot Coarse Grind Small Dot Fine Grind Adjusting the Coffee Quantity The machine allows you to adjust the amount of brewed coffee according to your tastes and or the size of your cups Each time you press and release button or the machine brews a pre programmed amount of coffee This y amount may be reprogrammed to your taste Each button may be individually programmed for a specific brew setting As an example the following procedure describes the programming of the button which is normally associated with espresso coffee Place a cup under the dispensing head Press and hold the button until the relevant icon is displayed At this point the machine is programming it The machine begins the dispensing phase The icon will be displayed to show which button is being pro grammed e Press the button with the icon again when the desired amount of coffee in the cup is reached At this point the button is pro grammed each time it is pressed and released the machine will brew the same amount of coffee that was just pro grammed Stand By The machine is designed for energy sav ing The machine automatically turns off after 60 minutes of inactivity Note During the switching off phase the machine per forms a rinse cycle if a coffee product has been brewed To turn the machine on again simply press
6. the ON OFF button and then switch the power button to 0 Remove the plug from the socket Wait for the machine to cool down Never immerse the machine in water It is strictly forbidden to tamper with the internal parts of the machine Water left in the tank for several days should not be consumed Wash the tank and fill it with fresh drinking water If the machine will not be used for a long time dispense water from the steam wand and care fully clean the Pannarello if supplied then turn it off and unplug it Store it in a dry place out of the reach of children Keep it protected from dust and dirt Servicing Maintenance In case of failure problems or a suspected fault resulting from the falling of the machine imme diately remove the plug from the socket Never attempt to operate a faulty machine Servicing and repairs may only be carried out by authorized service centers All liability for damages resulting from work not carried out by professionals is declined Fire Safety Precautions In case of fire use carbon dioxide Co extinguishers Do not use water or dry powder extin guishers Coffee bean hopper lid Coffee bean hopper Control panel Dispensing head Pre ground bypass doser Drip tray LIEN Full drip tray indicator NANN ssss SSS i j SS Service door Brew group Dregdrawer Wand protective gripper H lla Steam
7. the machine and to ensure with regular use ahigh quality delivered product Warning Never drink the des caling solution or any prod ucts dispensed until the cycle has 1 been carried out to the end Never use vinegar as a descaling solution Before descaling remove the Pannarello attachment from the steam hot water wand as described in the Cleaning and Maintenance section Turn the machine on by pressing the ON OFF button Wait for the machine to finish its rinse cycle and warm up Warning Remove the Intenza filter before adding the des caling solution Hold the o button for 5 seconds The display will show the icon on the side If you press the Ou button by mistake use the button to quit Press button to confirm the activation of the descaling cycle From this point forward the descaling cycle must be completed before proceeding Pour the entire content of the Saeco concentrated descaling solution into the water tank and then fill the tank with fresh drinking water up to the MAX level Place the tank back in the machine e Insert a container below the steam hot water wand Use a large container for this process If you do not have a container of this capacity once it is lt gt Sy filled close the knob empty the con tainer and then place it again under i H als J gt MEMO Red
8. water hardness value as specified in the pro gramming section Intenza Water Filter To improve the quality of the used water it is recommended that you install the water filter Remove the small white filter from the tank and store it in a dry place sheltered from dust Remove the water filter from its packag ing immerse it vertically with the open ings positioned upwards in cold water and gently press its sides so as to let the air bubbles out Set the Intenza Aroma System as specified on the box A Soft water B Hard water standard C Very hard water Insert the filter in the empty tank The reference mark and the groove must match Push firmly until it is completely inserted Fill the tank with fresh drinking water and re insert it into the machine Dispense the water in the tank by using the hot water function see section Hot Water Dispensing Fill the water tank again Press the ON OFF button to change the machine status to stand by mode N gt OFF 4 RESET MENU gt Black When the icon appears press the o button to access the machine program ming menu Press the E button until the follow ing page is displayed W Press the button to select ON and press the _ button to confirm In this way the machine has been pro grammed to inform the user of the need to replace the fi
9. ORY SETTINGS This function allows you to reset all fac tory values MENU Black MENU Black Programming example In this example we want to explain how to programme the display contrast Pro ceed in a similar manner to change the other functions Change the machine status to stand by mode When the machine is in stand by mode press the button to access pro gramming The first page is displayed Press the ue button until the CON TRAST function is displayed Press the button 1 one time to increase the contrast Press the a button to confirm per w Press the ON OFF button to exit the pro gramming mode At this point the function is programmed and will be active the next time the ma chine is started 21e Green 22e CONTROL PANEL DISPLAY eady Signals The machine is ready for whole bean coffee brewing and hot water dispensing e The machine is ready for pre ground coffee brewing e The machine is in the steam dispensing phase e The machine is in the hot water dispensing phase The machine is brewing 1 espresso coffee The machine is brewing 1 long coffee The machine is brewing 2 espresso coffees The machine is brewing 2 long coffees The machine is programming the amount of coffee to be brewed Warning Signals The machine is warming up to brew coffee and dispense hot
10. Register your product and get support at www philips com welcome LA Type HD8836 HD8837 SUP 037DR OPERATING INSTRUCTIONS a n READ THESE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE PHILIPS CE Saeco IMPORTANT SAFEGUARDS When using electrical appliances basic satety precautions should always be followed including the following l 2 3 8 9 Read all instructions Do not touch hot surtaces Use handles or knobs To protect against fire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug from outlet when not in use and before cleaning Allow to cool before putting on or taking off parts and before cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance maltunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surtaces 10 Do not place on or near a hot gas or electric burner or in a heated oven 11 Always attach plug to appliance first then plug cord into wall outlet To d
11. ach time the O button is pressed and released the aroma changes by one degree D Mild aroma 0g D Medium aroma Green O Strong aroma Selection must be made prior to brewing the coffee The system sets the aroma ac cording to the personal taste of the user After selecting Strong Aroma the func tion for brewing coffee with pre ground coffee is displayed This selection is displayed by the icon on the side Refer to the relevant section to use this function Using Coffee Beans To brew coffee press and release one of the following buttons the button to select the desired oe arom the button for an espresso cof MEMO fee the button for a long coffee MEMO The brewing cycle then starts To dispense 1 cup of coffee press the button once This icon will be displayed To dispense 2 cups of coffee press the button twice This icon will be displayed To brew 2 coffees the ma chine automatically grinds and doses the correct amount of coffee Brewing two coffees requires two grinding cycles and two brewing cycles which the machine carries out automatically After the prebrewing cycle coffee begins to come out of the dispensing head Coffee brewing stops automatically when the pre programmed level is reached however it is possible to in terrupt coffee brewing by pressing the button i
12. at other beverages Danger of scalding Brewing may be preceded by small spurts of hot water The steam hot water wand may reach high temperatures Never touch it with bare hands Important Note After using the steam hot water wand to froth milk immediately clean the wand or Pannarello when pro vided When the machine is ready dispense a small amount of hot water in a glass and clean the steam wand or Pannarello when provided EU gi Tle externally In this way all parts will be perfectly cleaned and free of any milk residue e Place a container under the steam hot water wand Pannarello if supplied When the machine is ready to brew coffee turn selector dial counter clockwise to set it onto the en posi tion Residual water may dispense from the steam hot water wand Pannarello if supplied The following icon is displayed during the preheating time required by the machine Steam dispensing will begin when the following icon is displayed soon after only steam will begin to come out Turn the selector dial clockwise and set it back to the B position to stop dispensing steam e Fill 1 3 of the container you wish to use to prepare the cappuccino with cold milk Use cold milk for better results when preparing a cappuccino 15 6 16 6 Immerse the steam hot water wand Pannarello if supplied in the milk to be heated
13. e shop where you purchased the product RE See label on the inside of the service door E SA E E Thermoplastic material Metal e a a a ee 10 x 12 5 x 16 256 x 315 x 415 mm EEEE EE P EEEE EEE E 20 Ibs 9 kg E E E E EEE A E EET 47 1 2m e E nee eee ta nana sdateaes Front side Neeegybaduaveveuapeeehuadven tees lad oety secede Special for cappuccinos E E T 1 2 litres Removable type EEEE EEEE EE E E ETT ans 9 2 0z 260 g E E E EE E E Stainless steel type E EAE E E E E ALNE NA Thermal fuse EC DECLARATION OF CONFORMITY YEAR 09 EC 2006 95 EC 2004 108 SAECO INTERNATIONAL GROUP S P A Via Torretta 240 40041 Gaggio Montano Bo Italy declare under our responsibility that the product AUTOMATIC COFFEE MAKER SUP 037DR towhich this declaration relates is in conformity with the following standards or other normative documents Safety of household and electrical appliances General requirements EN 60335 1 2002 A1 2004 A2 2006 A11 2004 A12 2006 A13 2008 Safety of household and electrical appliances Part 2 15 Particular requirements for appliances for heating liquids EN 60335 2 15 2002 A1 2005 A2 2008 Household and similar electrical appliances Electromagnetic fields methods for evaluation and measurement EN 62233 2008 Household and similar electrical appliances safety Part 2 14 Particular requirements for kitchen machines EN 60335 2 14 2006 A1 2008 E
14. equires the brewing of a certain number of coffees to allow the machine to adjust the compactness of the ground coffee Attention should be given to special blends which require grinder adjust ments in order to optimize the extrac tion of the coffee see section Coffee Grinder Adjustment Coffee Grinder Adjustment Warning The grinder adjust ment knob inside the coffee bean hopper must be turned only when the grinder is working Do not pour ground and or instant coffee into the coffee bean hopper Do not insert any material other than coffee beans into the hopper The grinder contains moving parts that may be dangerous Therefore do not insert fingers and or other objects Only grind setting by means of the knob is permitted Turn off the machine and unplug it from the socket before carrying out any type of operation inside the coffee e111 bean hopper Do not pour coffee beans when the coffee grinder is working The machine allows slight adjustments to the coffee grinder to adapt it to the kind of coffee used To make any adjustment press and turn the knob inside the coffee bean hopper Press and turn the knob by one notch at a time and brew 2 3 cups of coffee this is the only way to notice differences in grind The reference marks inside the coffee bean hopper indicate the grind setting 4 There are 5 different grind settings to choose from with the following refer
15. gh No hot water or steam is dispensed The coffee has little crema see note The machine takes a long time to warm up or the amount of water dispensed from the wand is too little The brew group does not come out The machine grinds the coffee beans but no coffee comes out See note The coffee is too weak see note Coffee is brewed slowly see note Coffee leaks out of the dispensing head Note These problems can be considered normal if the coffee blend has been changed or if the machine has just been installed Causes The machine is not connected to the power source The cups are cold The hole of the steam wand is clogged Pannarello is dirty if supplied The coffee blend is unsuitable the coffee is not freshly roasted or the grind is too coarse The machine circuit is obstructed by limescale build up The brew group is out of place Dregdrawer is inserted Water tank is empty Brew group is dirty Circuit is not primed Rare event that occurs when the machine is auto matically adjusting the dose The dispensing head is dirty Rare event that occurs when the machine is auto matically adjusting the dose The coffee grind is too fine The circuit is not primed The brew group is dirty The dispensing head is clogged Solutions Connect the machine to the power source Warm the cups with hot water Clean the hole of the steam wand using a pin Make sure that the machine i
16. he brewing cycle then starts After the pre brewing cycle coffee begins to come out of the dispensing head After dispensing the product the ma chine defaults back to the whole coffee bean configuration Repeat the operations de scribed above to brew other coffees DISPENSING HOT WATER Warning Dispensing may be preceded by short spurts of hot water and scalding is possible The steam hot water wand may reach high temperatures Do not touch with bare hands Use the appropriate handle only e Before dispensing hot water check that the following icon is displayed When the machine is ready proceed as follows Place a container under the steam hot water wand Pannarello if supplied Oe E telel m z o v z Orange Turn the selector dial clockwise to the position The following icon will be displayed Fill the cup with hot water to the desired level to stop hot water dis pensing turn selector dial counter clockwise back to the B position The machine returns to the normal operat ing mode Occasionally after turning the selector dial hot water may not be dispensed and the fol lowing icon may be displayed Simply wait until the end of the warm up phase at which point hot water will be dispensed from the wand Pannarello if supplied STEAM DISPENSIN e Steam may be used to froth milk for a cappuccino as well as to rehe
17. hot water wand SES Power switch SS es lt SSE Drip tray m Water tank Brew group lubricant Pre ground coffee scoop Power cord LCD Display Intenza water filter Strong coffee brew button Ca ON OFF button Long coffee brew button Aroma Pre ground coffee Teena selector button Coffee hot water steam dial INSTALLATION For your own and for other people s safety carefully follow the instruc tions provided in the Safety Regula tions section Machine Packaging The original packaging has been designed and constructed to protect the machine during transport We recommend keep ing the packaging material for possible future transport Preliminary Operations Remove the coffee bean hopper lid and the drip tray with grill from the packaging Remove the coffee machine from the packaging and position it in a place that meets the requirements described in the safety regulations Place the drip tray with grill into its appropriate seat on the machine Make sure it is fully inserted and clicks into place e Place the coffee bean hopper lid on the bean hopper Note Insert the plug in the machine and in the wall so cket only when indicated and check that the power button is switched to 0 Important Note Carefully read the explanations of all the warnings displayed on the LCD control panel section LCD Display Warnings Never remo
18. ing the water tank in the machine turn the selector switch clockwise to position gt Dispense the entire tank as previously described At the end fill the tank again When inserting the water tank again the icon on the side is displayed Press the O button to exit the descaling cyde e The machine now carries out the warm up and rinse cycle to prepare for product brewing Empty the container used to collect the liquid dispensed by the machine The descaling solution must be disposed of according to the manufacturer s instructions and or regulations in force in the country of use After completing the descal ing cycle wash the brew group as described in the Brew group section in the Cleaning and maintenance section 1 Reassemble the external part of the Pan narello 19 6 20 PROGRAMMING The user can change some of the ma chine operating parameters to suit his her needs Enter the menu The programming menu can only be ac cessed when the machine is in stand by mode To change the machine status to stand by mode press the ON OFF button When the machine is in stand by mode press the button to access pro gramming The first page that is displayed is shown here MENU Black Programming commands Changes can be made on each page The and buttons allow you to change the value of the function among tho
19. is set to the Q position if this is not the case set it to that position Press the ON OFF button to turn the machine on The display indicates that the circuit must be primed Note Before starting the machine after long periods of inactivity the water circuit must be primed A z z z s S oS Red Green m a 5 eT e eja Priming the Water Circuit To prime the water circuit place a container under the steam hot water wand Pannarello if supplied e Turn the selector dial clockwise to set it to the position The machine starts the automatic priming of the circuit by letting out a preset quantity of water through the steam hot water wand Pannarello if supplied The bar under the icon shows the operation progress At the end of the priming process the display shows an icon see fig ure indicating that the selection dial must be brought back to the central P position The display then shows the machine warm up icon as shown in the figure When warm up is complete the machine performs a rinse cycle of the internal circuits In this phase this icon will be dis played When the operations described above are complete this icon will be dis played The machine is then ready to brew beverages To brew coffee dispense hot water or steam and for a proper use of the ma chine carefully follow the instructions provided
20. isconnect turn any control to off then remove plug from wall outlet 12 Do not use appliance for other than intended use 13 Save these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is for household use only Any servicing other than cleaning and user maintenance should be pertormed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only l Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting trom becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if care is exercised in their
21. lectromagnetic compatibility EMC Requirements for household appliances electric tools and similar apparatus Part 1 Emission EN 55014 1 2006 Electromagnetic compatibility EMC Part 34 Limits Section 2 Limits for harmonic current emissions equipment input current lt 16A for phase EN 61000 3 2 2006 Electromagnetic compatibility EMC Part 3 Limits Section 3 Limitation of voltage changes voltage fluctuations and flicker in public low voltage sup ply systems for equipment with rated current lt 16 A for phase and not subject to conditional connection EN 61000 3 3 1995 corr 1997 A1 2001 A2 2005 Electromagnetic compatibility Requirements for household appliances elec tric tools and similar apparatus Part 2 Immunity Product family standard EN 55014 2 1997 A1 2001 following the provisions of the Directives EC 2006 95 EC 2004 108 Gaggio Montano li 28 04 2009 26 e 27e PHILIPS The manufacturer reserves the right to change the features of the product without prior notice www philips com saeco Rev 0O del 15 03 10 Type HD8836 HD8837 Cod 15002481
22. lter Note When an Intenza filter must be replaced with a new one the function must be reset Re place the filter as previously shown After that enter the programming menu until the indicated window is displayed and select the RESET option then press the _9 button The machine is now programmed to manage a new filter Note If the filter is already installed and you want to remove it without replacing it select the OFF option and then press the O button To exit press the ON OFF button until the stand by page is displayed Note If there is no Intenza water filter insert the small white filter previously removed into the water tank ADJUSTMENTS The machine that you have bought allows for certain adjustments that will permit you to use it to its full potential Saeco Adapting System Coffee is a natural product and its char acteristics may change according to its origin blend and roast The Saeco coffee machine is equipped with a self adjusting system that allows the use of all types of coffee beans available on the market not including flavored or carmelized The machine automatically adjusts itself in order to optimize the extrac tion of the coffee ensuring perfect compression of the beans to obtain a creamy espresso coffee that is able to release all the aromas regardless of the type of coffee used The optimization process is a learning process that r
23. nitially pressed 13 6 14 The machine is adjusted to brew a true Italian espresso coffee This feature may slightly lengthen the brewing time allowing the intense flavor of the coffee to develop fully Using Pre Ground Coffee This function allows using pre ground and decaffein ated coffee Pre ground coffee must be poured into the bypass doser positioned next to the coffee bean hopper Only use coffee ground for espresso machines and never coffee beans or instant coffee ES f no pre ground coffee is poured into the bypass doser only water will be dispensed If the dose is excessive and 2 or more measuring scoops of coffee are used the machine will not brew the product In this case the machine will run an empty cycle and discharge any ground coffee into the dregdrawer To brew coffee Press and release the button to select the pre ground coffee function Lift the pre ground bypass doser cover Add only 1 scoop of pre ground coffee to the compartment Use the measur ing scoop supplied with the machine to perform this operation Then close the cover Warning Only add pre ground coffee to the bypass doser Other substances and objects may cause severe damages to the ma chine Such damages will not be covered by warranty Press and release the button for an espresso cof MEMO fee the button for a long coffee T
24. ns of the product Nominal Voltage Power Rating Power Supply 0 ceceeeeeees Housing material ee SIZE WANN Oeren eaa e A EE EAEE Wai Power Cord Length 4st maces tantcudendiekasauciaws iaewbe mecatownd ad Control Panel 7 as Pannarello only available for certain models Watertank et Coffee Bean Hopper Capacity cc ccseeee cece eeeeeeeeeeeneeees Dregdrawer Capacity 7 Pump pressure 2 cc2ai cecsgee eeeeasdacdwereesseecabwieseasessdaertass DUNK Safety MOCHANISING lt ccincagudaaaudinenganatedstedionnaatcaudccioenne MACHINE DISPOSAL The packing materials can be recycled Appliance Unplug the appliance and cut the power cord Deliver the appliance and power cord to a service center or public waste disposal facility This product complies with eu directive 2002 96 ec H The symbol mmama On the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help pre vent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or th
25. ot water wand Pannarello if supplied to obtain a thorough cleaning Every day after frothing the milk remove the external part of the steam hot water wand and wash it with fresh drinking water Clean the steam wand weekly In order to do this you have to Remove the external part of the Pannarello for standard cleaning Remove the upper part of the Pannarello from the steam wand Wash the upper part of the Pannarello with fresh drinking water Wash the steam wand with a wet cloth and remove any milk residue Replace the upper part in the steam wand make sure it is completely inserted Reassemble the external part of the Pannarello 1 SR CN TA A Up ae i FN iN 3 It is recommended to clean the water tank daily Remove the small white filter in the water tank and wash it under running drinking water Reposition the small white filter in its housing by gently pressing and turning it at the same time Fill the water tank with fresh drinking water Empty and clean the drip tray daily Perform this operation also when the float is raised Also clean the seat of the tray every week through the openings on the bottom of the machine Brew Group The brew group must be cleaned at least once a week Turn off the machine by pressing the ON OFF button and remove the plug from the socket
26. s turned off and has cooled before performing this ope ration Clean the Pannarello Change coffee blend or adjust the grind as explained in the Coffee Grinder Adjustment section Descale the machine Turn the machine on Close the service door The brew group automatically returns to the correct position Remove the dregdrawer first then the brew group Fill the water tank and prime the circuit section Using the Machine for the First Time Clean the brew group section Brew Group Prime the circuit section Using the Machine for the First Time Brew a few coffees as described in section Saeco Adapting System Clean the dispensing head Brew a few coffees as described in section Saeco Adapting System Change coffee blend or adjust the grind as ex plained in the Coffee Grinder Adjustment sec tion Prime the circuit section Using the Machine for the First Time Clean the brew group section Brew Group Clean the dispensing head and its holes In this case wait until the machine performs a self adjusting operation as described in section Saeco Adapting System Please contact Saeco Customer Service or an authorized service center for any problems not covered in the above table or when the suggested solutions do not solve the problem 24 TECHNICAL SPECIFICATIONS The manufacturer reserves the right to make changes to the technical specificatio
27. se appearing on the page The button allows you to scroll the functions and to store the changes that were made Note Changes can be stored only after the displayed value is changed when the displayed value is changed the OK message appears The ON OFF button allows you to exit the change or programming mode Exit programming mode To exit the programming mode press the ON OFF button until the stand by page is displayed Note The machine will exit the programming mode if the user does not do anything for 30 seconds The settings that were changed but not confirmed will not be stored YES gt NO 4 ESC ean Functions COFFEE TEMPERATURE This function allows you to adjust the cof fee brewing temperature TIMER STAND BY This function allows you to adjust the time the machine will go into stand by mode after the last brewing CONTRAST This function allows you to adjust the contrast of the display to better view the messages WATER HARDNESS This function allows you to adjust the water hardness in order to better manage machine maintenance very soft water wh soft water hh hard water hh very hard water For more details see the Water hardness measure ment section INTENZA WATER FILTER This function allows you to manage the Intenza water filter For more details see the section related to filter handling FACT
28. temperature outside the operating temperature range 15 C 45 C The use of non original spare parts and accessories In these cases the warranty shall be deemed null and void SAFETY REGULATIONS Never allow water to come into contact with any of the electrical parts of the machine Danger of short circuit Steam and hot water may cause scalding Do not direct the steam hot water wand towards body parts Carefully handle the steam hot water wand by its grip Danger of scalding Intended Use The coffee machine is intended for domestic use only Do not make any technical changes or use the machine for unauthorized purposes since this would create serious hazards The appliance is not to be used by persons including children with reduced physical mental or sensory abilities or with limited experience and or expertise unless they are supervised by a person responsible for their safety or they are instructed by this person on how to properly use the machine Power Supply Power Cord Only connect the coffee machine to a suitable socket The voltage must correspond to that indicated on the machine label located on the inside of service door Never use the coffee machine if the power cord is defective or damaged If damaged the power cord must be replaced by the manufacturer or an authorized service center Do not pass the power cord around corners over sharp edges or over hot objects and keep it away from oil Do not use the po
29. the ON OFF button if the power switch is set to l In this case the ma chine will go through the rinse cycle only if the boiler is cold COFFEE BREWING Note Should the machine not brew coffee make sure that the water tank contains water Before brewing coffee check the messages on the display Check that the water tank and coffee been hopper are full Leave the dial on the coffee position 9 during the dis pensing phase Before brewing the coffee adjust the height of the brew ing head according to your needs and select the aroma or the pre ground coffee ET BA 6 f LP Dispensing Head Adjust ment Most cups on the market can be used with this coffee machine The height of the dispensing head may be adjusted to better fit the dimensions of the cups that you wish to use Manually move the dispensing head up or down to adjust its height by placing your fingers as shown in the figure D The recommended positions are For use with small cups For use with big cups Two cups mugs can be placed under the dispensing head for brewing two coffees at the same time Aroma Adjustment Aroma adjusts the quantity of coffee to be ground or sets the use of pre ground coffee Four choices are possible by pressing and releasing the a button mild medi um or strong aroma and ground coffee Selection can be made when the beans appear on the display E
30. use If a long detachable power supply cord or extension cord is used l The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 It the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over lt GENERAL INFORMATION The coffee machine is suitable for preparing espresso coffee using either coffee beans or ground coffee and is equipped with a device to dispense steam and hot water The structure of the ma chine has been designed for domestic use only and is not suitable for continuous professional type operation Keep these operating instructions in a safe place and make them available to anyone who may use the coffee machine For further information or in case of problems that are not included or not completely explained in these instructions please contact an authorized service center AN Warning No liability is held for damage caused by Incorrect use not in accordance with the intended purposes Repairs not carried out by authorized service centers Tampering with the power cord e Tampering with any parts of the machine Storage or use of the machine at a
31. ve the drip tray when the machine is turned on Wait a couple of minutes after turning on off since the machine will be carrying out a rinse self cleaning cycle see section Rinse Self cleaning Cycle Remove the water tank and install the Intenza water filter as recommended on page 27 Fill the tank with fresh drinking water Do not exceed the max level indi cated on the water tank Once filled place the tank back into the machine Fill the tank only with fresh non sparkling water Hot wa ter or any other liquid may damage the tank and or the machine Do not turn on the machine when the tank is empty Make sure there is enough water in the tank Remove the coffee bean hopper lid Note The hopper may be pro vided with different safety features according to the regula tions of the country of use of the machine Slowly pour the coffee beans into the hopper Only coffee beans may be put into the coffee bean hopper Ground coffee instant coffee or any other object may damage the machine Replace the coffee bean hopper lid Insert the plug into the socket on the back of the machine Insert the plug of the other end of the cable into a wall socket with suitable power voltage e o SABO Qe Turn the machine ON by pressing the mr power switch to The display shows the ON OFF icon Make sure the ON OFF button
32. water or steam The machine is performing the rinse cycle Wait until the machine automatically stops brewing the beverage The machine must be descaled The brew group is being reset due to machi ne reset The coffee bean hopper needs to be refilled with coffee beans to restart the brewing cycle The Intenza filter must be replaced with a new one p 0 i This message will only be dis played if the function is activated in the programming mode The alarm is deactivated only if it is RE SET in the programming mode Red Red Alarm Signals Return the hot water steam knob to its proper position e Close the service door Refill the coffee bean hopper e Turn the machine off After 30 seconds turn it back on Try 2 or 3 times If the machine does NOT start contact an authorized service center Insert the brew group in the machine Problems with the water circuit Insert the dregdrawer Empty the dregdrawer and the drip tray Fill the water tank Red Start screen for descaling cycle activation Press OK to continue or ESC to quit Open the knob to carry out the operation described Descaling cycle in progress Descaling cycle ended Press the e button to quit the descaling cycle Fill the water tank e236 TROUBLESHOOTING Machine Actions The machine does not turn on The coffee is not hot enou
33. wed 6 Repeat the operations from step 1 to step 5 for 3 times then continue with step 7 7 Place a container underthe steam wand Pannarello if supplied A small amount of water will be dis pensed to rinse and heat all the machine components in this phase this icon is displayed Wait for the cycle to finish automatically You can stop dispensing as well by pressing either coffee button and or 8 Turn the selector switch clockwise to set the ON OFF button it to the WP position TT TD E SS ie 10 Water hardness measurement The water hardness measurement is very important in order to correctly manage the Intenza filter and the frequency with which the machine must be descaled Immerse the water hardness test strip provided with the machine in water for 1 second Note The test strip is only valid for one measurement Check how many squares change colour and refer to the table The letters correspond to the references that are located in the base of the Intenza filter The filter must be adjusted based on this measurement Intenza Aroma System Machine water hardness setting The numbers correspond to the settings that are found for the water hardness ad justment that is shown in the program ming section More precisely 1 amp very soft water 2 hh Soft water 3 k k k hard water 4 gh dab very hard water Once this value is known set the
34. wer cord to carry or pull the coffee machine Do not pull out the plug by the power cord or touch it with wet hands Do not let the power cord hang freely from tables or shelves For the Safety of Others Keep children under control to prevent them from playing with the product Children are not aware of the risks related to electric household appliances Do not leave the machine packaging materials within the reach of children 6inches 6 inches Danger of Burns Never direct the steam hot water wand towards yourself or others Danger of scalding Always use the handles or knobs provided Machine Location Suitable Location for Operation and Maintenance For best use it is recommended to Choose a safe level surface where there will be no danger of overturning it or being inju red Choose a location that is sufficiently well lit clean and near an easily reachable socket Provide for a minimum distance from the sides of the machine as shown in the illustration During machine turning on off it is recommended to place an empty glass under the dispen sing head Do not keep the machine at a temperature below 0 C 32 F Frost may damage the machine Do not use the coffee machine outdoors In order to prevent its housing from melting or being damaged do not place the machine on very hot surfaces and close to open flames Storing the Machine Cleaning Before cleaning the machine turn it off by pressing
Download Pdf Manuals
Related Search