Sharkoon Bandit
Contents
1. Mainboard mounting panel C Installation opening for CPU coolers D Quick fasteners for ODDs E Removable HDD cage A Card reader USB connector B Audio connectors for a HD Audio b AC 97 Connectors for f l t r Power Switch Reset Switch Power LED HDD LED Power LED D USB connector of the USB front hub E eSATA connector F 3 pin and 4 pin fan connector Note 3 Remove the mainboard and screw the stand offs into the respective drillings For more information on how to install the intended devices refer to their of the mounting panel fig 3 respective documents 5 Installation of a mainboard 1 Open the case by loosening the thumb screws on the case s back side and removing the left side panel Lay down the case sidewise on an even surface 2 The mainboard s mounting panel inside the case provides various drillings to fix the stand offs fig 1 fig 3 fig 1 4 Press the I O shield delivered with the mainboard into the I O shield opening in the case s back side 5 Place the mainboard back onto the stand offs and screw the mainboard to The mainboard contains special screw openings fig 2 them fig 4 Place the mainboard to the mounting panel A stand off must be screwed into every drilling of the mounting panel visible through the mainboard s screw openings 6 Plug the connectors of the case s front bezel to the respective conn2. Back side of case 1x 120mm or 1x 80mm fan optional Top panel 1x 180mm LED fan pre installed Package contents ATX case Bandit 1x 120mm LED fan in the case front 1x 180mm LED fan in the top panel and card reader pre installed Accessory kit Stand offs for Screws for drive Screws for HDD Screws with mainboard mainboard mounting PSU mounting coarse thread View from above A Topl O a Reset button b 1x eSATA connector and c 2x USB2 0 connectors d Powerbutton e f g Quick fasteners for Lock attachment A speaker optical drives B and plastic case feet pre installed black self adhesive C SATA docking station LEDs 1x headphone and microphone connector Mounung mame One 5 25 bezel with opening for 3 5 devices devices B Pre installed 180mm LED fan Note If you are missing any of the items listed above please contact customer service via e mail at support sharkoon com or call 49 0 6403 775 6100 4 Thecase ata glance Front view Side view closed left Pre installed card reader 5 25 mounting bays behind the front bezel pre installed 120mm LED fan OWD I A Fan brackets 120 mm and 140 mm BANDIT Side view opened left Back side view A Opening for I O shield B Fan bracket for 80mm or 120mm fan C Slot bezels D PSU bracket E Thumb screws A Mounting bays for 5 25 devices B
3. diharkoor m lt _ lt x Content Features Fan configuration Package contents The case at a glance Installation of a mainboard Installation of a PSU Installation of a HDD Installation of an optical device Installation of an additional 3 5 device 10 Installation of an add on card 11 The pre installed fans 12 Installation of additional fans optimized airflow 13 The docking station for SATA HDDs in the case s top panel SOHO SONS Dear customer Congratulations for purchasing one premium quality SHARKOON product For a long life time and to take full advantage of this product we recommend that you read this manual completely Have a good time with our product SHARKOON Technologies Features ATX case 5x 5 25 drive bays external 3x 3 5 drive bays internal Top I O with 2x USB2 0 1x eSATA 1x headphone and 1x microphone connector power and reset button as well as LEDs for power and HDD activity Installed SATA docking station in case top for 2 5 and 3 5 HDDs Pre installed card reader with USB2 0 connector supported card formats SD SDHC MS MMC CF 7 slots for add on cards Mesh front panel for optimized cooling Quick fasteners for optical drives Dimensions 485 x 485 x 200 mm L x H xW Weight 6 6 kg Fan configuration 1x 120mm LED fan with 3 pin and 4 pin connector Case front pre installed Side panel 2x 140mm or 2x 120mm fans optional
4. ectors of 7 Installation of a HDD the mainboard also refer to vour mainboard s manual for further information 1 Remove the case s right side panel Note l 2 Remove the front bezel s fixation screws on both sides fig 7 The eSATA cable connected to the front eSATA connection should not exceed 50 cm of length otherwise transmission errors may occur With premium quality eSATA cables this maximum length may be exceeded 6 Installation of a PSU 1 Set up the case in front of you and put the PSU from the inside against the PSU bracket on the case s back side fig 5 L Ilum ME A im min a Ce oe a fig 7 fig 5 3 Remove the case s front panel by gently dragging it towards you fig 8 2 Screw the PSU to the case from the outside fig 6 Screws for PSU mounting k blu fig 8 4 Loosen the attachment screws of the HDD cage fig 9 fig 11 7 Slide the HDD cage back into the case and screw it from both sides fig 12 and 13 fig 10 6 Slide the HDD into a mounting bav of the HDD cage and fixate it from both sides fig 11 Screws for HDD mounting fig 13 8 Connect the HDD to the power supply and the mainboard BANDIT 8 Installation of an optical device 1 Remove the case s front panel by gently dragging it towards you fig 14 fig 14 2 Dismantle the 5 25 front bezel from the mounting bay in which you intend to ins
5. lease act according to vour local rules and do not dispose of vour old products with vour normal household waste The correct disposal of vour old product will help prevent potential negative consequences to the environment and human health SHARKOON Technologies 2010 www sharkoon com
6. nt side bottom and blown out on its back side top The PC components with the highest heat development should be placed directly within the airflow BANDIT 13 The docking station for SATA HDDs in the case s top panel 1 Connect the docking station s internal SATA plugs to the respective connectors of the mainboard and the power supply fig 29 SATA power connector 15 pin SATA data connector 7 pin UP fig 29 2 Insert either a 2 5 or a 3 5 SATA HDD into the SATA docking station fig 30 and fig 31 fig 30 fig 31 Legal disclaimer As acontinuing policy of product improvement at SHARKOON the design and specifications are subject to change without prior notice National specifications may vary All rights reserved especially also in extracts for translation reprinting repro duction by copying or other technical means Infringements will lead to com pensation All rights reserved especially in case of assignation of patent or utility patent Means of delivery and technical modifications reserved Disposal of your old product Your product is designed and manufactured with high quality materials and components which can be recycled and reused A When this crossed out wheeled bin svmbol is attached to a product it means the product is covered bv the European Directive 2002 96 EC Please be informed about the local separate collection svstem for electrical and electronic products P
7. r ODDs fig 24 il pe ja TETE im Kemanzj iil fig 20 fig 21 Carefully take out an optionally present metal bezel covering the drive bay bv using a gripper fig 23 fig 24 Note If you intend to transport the case we recommend securing additionally the installed drives mABRIMI QANW l AmA i l OJ Una f oe Ea E 5 Connect the 3 5 device to the power supply and the mainboard 6 Screw the 5 25 bezel with 3 5 opening into the front panel and place it back onto the case 5 25 bezel with 3 5 opening 10 Installation of an add on card 1 Press the slot bezel out of its attachment fig 25 2 Insert the add on card into the mainboard s respective slot and screw it to the case fig 26 Screw with coarse thread 11 The pre installed fans 1 The pre installed case fans provide a 4 pin PSU connector and a 3 pin mainboard plug each 2 Connect one of both plugs to either the respective PSU or to control the fan speed via the mainboard the matching mainboard connector 12 Installation of additional fans optimized airflow 1 Place the fan against the respective bracket from the inside e g the back side fig 27 2 Screw the fan to the attachment from the outside fig 28 fig 28 3 Connect the fan s power plug to the PSU or the mainboard Note While installing fans make sure that cool air is taken in on the cases fro
8. tall the drive by loosening its screws and pushing the bezel to the inside fig 15 Remove the quick fasteners fig 16 fig 15 Carefully take out an optionally present metal bezel covering the 3 5 drive bay by using a gripper 3 Slide the optical drive into the case s drive bay fig 17 l Cenc CET fie b 1 CLLD LI i L G N f es on pi fe MOTA fe ait EIl m fig 17 4 Attach the optical device from both sides using the quick fasteners fig 18 fig 18 Note If you intend to transport the case we recommend securing additionally the installed drives Screws for 5 25 drive mounting 5 Connect the optical drive to the power supply and the mainboard Put the front bezel back onto the case BANDIT 9 Installation of an additional 3 5 device 3 Place the 3 5 device into the mounting frame for 3 5 devices and screw it to the mounting frame from both sides fig 22 1 Remove the case s front panel by gently dragging it towards you fig 19 Mounting frame for 3 5 devices fig 19 2 Dismantle the 5 25 front bezel from the mounting bay in which you intend to install the drive by loosening its screws and pushing the bezel to the inside fig 20 Remove the quick fasteners fig 21 fig 22 4 Slide the mounting frame with installed 3 5 device into the case s drive bay fig 23 and attach it to the drive bay from both sides using the quick fasteners fo
Download Pdf Manuals
Related Search