TFA 30.3150 digital body thermometer
Contents
1. Viewing Pressure and Altitude Data In Pressure and Weather Forecast Mode each press of SET rotates display between Sea level pressure Local pressure Local altitude Setting the Sea Level Pressure 1 In Pressure and Weather Forecast Mode press SET until the sea level pressure is displayed 2 Press and hold SET The Sea Level Pressure display should be flashing 3 Set Sea Level Pressure Press UP or DOWN to adjust value Press and hold either button for fast advance Press SET to confirm your selection 4 Upon completion the display will be returned to Pressure and Weather Forecast Mode 47 Setting the Pressure and Altitude Units 1 In Pressure and Weather Forecast Mode press SET until local pressure is displayed 2 Press and hold MEMORY The pressure unit should be flashing 3 Set Local Pressure Units Press UP or DOWN to adjust unit Press MEMORY to confirm your selection 4 Set Altitude Units Press UP or DOWN to adjust value Press MEMORY to confirm your selection 5 Set Sea Level Pressure Units Press UP or DOWN to adjust value Press MEMORY to confirm your selection 6 Upon completion the display will be returned to Pressure and Weather Forecast Mode Viewing the Sea Level Pressure History 1 In all modes pressing HISTORY will toggle the sea level pressure display 2 When sea level pressure is displayed press HISTORY repeatedly to view sea level pressure data for each of the last 24 hours 3 If no buttons2. displays OFF if single alarm deactivated Pre Alarm Time displays OFF if pre alarm deactivated 2 When the above alarms are displayed pressing UP or DOWN will activate deactivate the corresponding alarm Note Press SET anytime during alarm selection mode to return to normal clock display a up the Time Alarms 1 In Clock and Alarm Mode press ALARM CHART to select alarm which you wish to configure 2 Press and hold ALARM CHART until hour starts flashing in the display 3 Set Alarm Hour Press UP or DOWN to adjust value Press and hold either button for fast advance Press ALARM CHART to confirm your selection 4 Set Alarm Minutes Press UP or DOWN to adjust value Press and hold either button for fast advance Press ALARM CHART to confirm your selection 5 Set Duration of Snooze Function all three alarms share same snooze time duration Press UP or DOWN to adjust value Press and hold either button for fast advance Press ALARM CHART to confirm your selection 6 Upon completion the display will be returned to the alarm selection screen Note Pre alarm cannot be activated if weekday alarm or single alarm is not enabled 51 Disabling Entering Snooze when Time Alarms are Activated To Enter Snooze Press SNOOZE to enable snooze function Note Alarm will automatically enter snooze mode if no key is pressed after the alarm sounds for 2 minutes This will occur for a maximum of three times To Disable Alarm s Press AL
3. iai a Wind Direction Compass Points Wind Speed Gust NE Beatings Max Wind speed wt ors Max Gust DAILY MAX ALARM H Vw S Wind Direction in Wind Alert Gust Alert GUST Compass Points Ai JIE Erh Bearing mph knots OC Eu Customizing your Weather Station To fully customize the weather station to your local settings and personal preferences the following settings are required Please refer to the appropriate sections for detailed instructions Required Setting Pressure Parameters during Initial Start Up Pressure and Weather Forecast Mode Setting up the Time Date and Language Clock and Alarm Mode Setting up the Location Data Sunrise Sunset Mode Optional Setting up the Time Alarms Clock and Alarm Mode Setting up the Temperature Alerts Temperature and Humidity Mode Setting up the Daily Rainfall Alerts Rain Mode Setting up the Wind Alerts Winds Mode Navigating between Different Modes There are 6 modes available on the main console unit and each one displays a different category of data When display is in a certain mode its corresponding icon will start flashing To navigate between the different modes from the main console unit press UP to cycle through the modes in a clockwise direction or DOWN to cycle through the modes in an anti clockwise direction 46 Using the Different Weather Modes 1 Pressure and Weather Forecast Mode This part of the display indicate
4. last week and last month inch or mm Daily rainfall alert if rainfall for the current day exceed pre specified amount Section VI Wind Temperature at place of anemometer Temperature adjusted to wind chill factor C or F Wind direction compass display Wind direction angles available as compass points or bearings Average wind speed and gust speed mph m s knots and km h Daily Maximum wind speed and gust speed memory Wind speed alert for average wind speed and wind gust speed 43 Description of Graphics Pressure and Weather Forecast Mode Current pressure trend and history bar chart Weather forecast Moon phase MOONPHASE Pressure and Weather MOON EHASELWENTBES l et Forecast Mode icon gt I Moon Phase E Weather Forecast Pressure Trend SEA LEVEL HISTORY 2 mB hPa History selection for PRESSURE Pressure and Moon Phase 5 Humidity 24 18 12 6 3 2 1 0 hPamBar Local Pressure Sea Level Pressure History Bar chart for Pressure Temperature 1a0d es ee T Altiude LA Clock and Alarm Mode Radio Controlled clock showing current time and calendar Single alarm weekday alarm and pre alarm Clock Module icon TIME PM 1 e nl i p E ne a as MS Single Alarm Radio Controlled IL IL mom uw Weekly Alarm Clock Signal Status ye S Weekday City Second Time Date Display Yea
5. Ohio CLE 5 Columbus Ohio CMH 5 Dallas Tex DAL 6 Denver Colo DEN 7 Detroit Mich DTW 5 El Paso Tex ELP 7 Houston Tex HOU 6 Indianapolis Ind IND 5 Jacksonville Fla JAX 5 Las Vegas Nev LAS 8 Los Angeles Calif LAX 8 Memphis Tenn MEM 6 Miami Fla MIA 5 Milwaukee Wis MKE 6 Minneapolis Minn MSP 6 SU SU SU SU SU SU SU SU SU SU SU NO SU SU SU SU SU SU SU City Code Montreal Que Can YMX Nashville Tenn BNA New Orleans La MSY New York N Y NYC Oklahoma City Okla OKC Omaha Neb OMA Ottawa Ont Can YOW Philadelphia Pa PHL Phoenix Ariz PHX Pittsburgh Pa PIT Portland Ore PDX San Antonio Tex SAT San Diego Calif SAN San Francisco Calif SFO San Jose Calif SJC Seattle Wash SEA St Louis Mo STL Tampa Fla TPA Toronto Ont Can YTZ Vancouver B C Can YVR Vancouver Canada VAC Washington D C DCA 62 Zone Offset DST SU SU SU SU SU SU SU SU NO SU SU SU SU SU SU SU SU SU SU SU SU SU World Cities City Addis Ababa Ethiopia Adelaide Australia Algiers Algeria Amsterdam Netherlands Ankara Turkey Asuncion Paraguay Athens Greece Bangkok Thailand Barcelona Spain Beijing China Belgrade Yugoslavia Berlin Germany Birmingham England Bogota Colombia Bordeaux France Bremen Germany Brisbane Australia Brussels Belgium Bucharest Romania Budapest Hungary Buenos Aires Argentina Code AD
6. mph m s or knots Viewing Wind Statistics In Wind Mode each press of MEMORY rotates wind speed display between Current wind speed Daily maximum wind speed DAILY MAX is displayed Gust speed GUST is displayed Daily maximum gust speed GUST DAILY MAX is displayed Resetting the Wind Statistics Memory In Wind Mode press and hold MEMORY to reset all wind statistics 57 Activating Deactivating Wind Alerts 1 In Wind Mode each press of ALARM CHART rotates wind speed display between Current wind speed Wind speed alert ALARM HI displayed Gust alert GUST ALARM HI displayed If the alert is deactivated OFF will be shown otherwise the alert value is shown 2 When a wind alert is displayed pressing UP or DOWN will activate deactivate it Setting up the Wind Alerts 1 In Wind Mode press ALARM CHART to select alarm which you wish to configure 2 Press and hold ALARM CHART until alert and corresponding icon starts flashing in the display 3 Set Value for Alert Press UP or DOWN to adjust value Press and hold either button for fast advance Press ALARM CHART to confirm your selection 4 Upon completion the display will be returned to the wind alert selection screen Disabling when Wind Alert is Activated To Disable Wind Alert Press ALARM CHART to disable the alert PC Connection e Delivered with setup CD ROM in English and German and 2 metres of cable for the base compu
7. the indoor temperature and humidity data to compute a comfort level rating of Wet Comfort or Dry A temperature alert function is available for each channel It can be programmed to sound if the channel temperature exceeds or falls below the pre configured upper and lower limits Note The temperature alerts have a 0 5 C hysteresis to prevent the alerts from sounding constantly due to small fluctuations near the alert value This means that after the temperature reaches the alert value it will have to fall below the alert value plus the hysteresis to deactivate the alert Accessing Temperature and Humidity Mode From the main console unit Press UP or DOWN until the IN icon and the OUT icon on the upper right of the display starts flashing Viewing Temperature and Humidity Display for each Channel For Static Display In Temperature and Humidity Mode each press of CHANNEL rotates display between different channels For Cycling Display To enable automatic rotating between different channel displays press and hold CHANNEL until the G icon is displayed Each valid channel will now be alternately displayed for 5s Press and hold CHANNEL to deactivate ist Rotating Between Temperature and Dew Point Display In Temperature and Humidity Mode each press of SET rotates temperature display between Temperature and Relative Humidity Dew Point Temperature and Relative Humidity Setting Units for Temperature Display C or F In Tem
8. ARM CHART to disable the alarm s Note For weekday alarm pressing ALARM CHART will only disable the alarm for the current day The alarm will be activated again the next day if it falls within Monday to Friday Activating Deactivating Radio Clock Reception The main console unit synchronizes the time and date with radio clock broadcasts to maintain atomic clock precision To turn this function on off Press and hold UP If RC reception is activated a triangular tower icon will start flashing beside the clock icon If RC reception is deactivated the triangular tower icon will disappear Icon RC Reception Strength NI 7E Blinks Undefined data 7 N Reception failed for 24 hours Nay amp Weak signal but can be decoded Q Strong signal Note The radio controlled signal for time DCF 77 is transmitted from the central atomic clock in Frankfurt Main in short intervals It has a reception range of approx 1500 km Obstructions such as concrete walls can reduce the signal range 3 Sunrise Sunset Mode The main console unit computes the sunrise and sunset times from the user configured location data This includes the longitude latitude time zone and DST Daylight Saving Time Choosing a suitable city code for your area will automatically generate the correct values for the location data Should you wish to input your own location data or if a suitable city code could not be found choose USR as the city code during setu
9. Calendar and sunrise sunset Times Calendar and longitude latitude Viewing Sunrise Sunset Times for Different Dates 1 In Sunrise Sunset Mode press MEMORY 2 The date should be flashing Press UP or DOWN to adjust date Press and hold either button for fast advance The corresponding sunrise and sunset times will be displayed for the selected date 3 Press MEMORY or SET to return display to Sunrise Sunset Mode Understanding the Sunrise Sunset Display The sunrise time being displayed differs during the morning and the afternoon night From 12 am to 12 pm The sunrise time for the current day will be displayed From 12 pm to 12 am The sunrise time for the next day will be displayed NEXT DAY icon will be displayed above the sunrise time 33 At certain locations especially those at high latitudes sunrise and sunset events may not occur within a 24 hour time frame Display Sunrise status Display Sunset status FULL Sunrise at previous day FULL Sunset at next day or later No sunrise for the whole day No sunset for the whole day 4 Temperature and Humidity Mode The weather station supports up to 5 remote thermo hygro sensors each sensor corresponding to a separate channel for the temperature and relative humidity display The temperature may be shown in degrees Celsius C or degrees Fahrenheit F The trend rising steady or falling of all values is also indicated on the display The main console unit uses
10. D ADL ALG AMS AKR ASU ATH BKK BCN BEJ BEG BER BHX BOG BOD BRE BNE BRU BBU BUD BUA Zone Offset 9 5 ie OAAgm inn DST NO SA NO SE SE sp SE NO SE NO SE SE SE NO SE SE NO SE SE SE NO City Cairo Egypt Calcutta India as Kolkata Cape Town South Africa Caracas Venezuela Chihuahua Mexico Copenhagen Denmark Cordoba Argentina Dakar Senegal Dublin Ireland Durban South Africa Frankfurt Germany Glasgow Scotland Guatemala City Guatemala Hamburg Germany Havana Cuba Helsinki Finland Hong Kong China Irkutsk Russia Jakarta Indonesia Johannesburg South Africa Kingston Jamaica 63 Code CAI CCU CPT CCS CUU CPH COR DKR DUB DUR FRA GLA GUA HAM HAV HEL HKG IKT JKT JNB KIN Zone Offset 5 5 DST sg NO NO NO SU SE NO NO SE NO SE SE NO SE SH SE NO SK NO NO NO City Code Time DST City Zone Kinshasa Congo FIH 1 NO Oslo Norway Kuala Lumpur Malaysia KUL 8 NO Panama City Panama La Paz Bolivia LPB 4 NO Paris France Lima Peru LIM 5 NO Perth Australia Lisbon Portugal LIS 0 SE Prague Czech Republic Liverpool England LPL 0 SE Rangoon Myanmar London England LON 0 SE Reykjavyk Iceland Lyon France LYO 1 SE Rio de Janeiro Brazil Madrid Spain MAD 1 SE Rome Italy Manila Philippines MNL 8 NO Salvador Brazil Marseille France MRS 1 SE Santiago Chile Melbourne Australia MEL 10 SA Sao Pau
11. Professional Weather Center Ut PE ad rr sole JE BL MON ww Aig coe m 3 y 3 ES 3 PEN ar go 75 USER S MANUAL 35 Introduction Congratulations on your purchase of the SINUS WEATHER STATION The weather station consists of a main console unit as well as an assortment of remote sensors which collect and transmit a wide range of weather data including outdoor temperature humidity wind speed wind direction and rain amount The main console unit stores around 200 weather records without a computer connection When linked to a computer using the USB cable and software provided an unlimited number of weather records can be displayed and saved onto the computer CESS weather sy ec ts We el 3 in ME Mice Jy 5 ERA wino cHILL on IE Fe MON Fr TT FEAR Main Console Unit The main console unit features a radio controlled atomic precision clock with alarm and weather forecast It measures indoor temperature and humidity and displays weather data collected by the remote weather sensors It also provides indication of the indoor outdoor temperature pressure and humidity trends and celestial information such as moon phase and sunrise set times Remote Weather Sensors The remote weather sensors include a thermo hygrometer anemometer wind sensor and rain sensor All data collected by the sensors i
12. R amp TTE Directive applied standard s EN 300 220 3 2000 Electromagnetic compatibility Article 3 1 b of the R amp TTE Directive applied standard s EN 301 489 1 3 2000 Low voltage directive applied standard s EN 60950 1 2001 Additional information The product is therefore conform with the EMC Directive 89 336 EC and R amp TTE Directive 1999 5 EC appendix II and carries the respective CE marking RTTE Compliant Countries All EU countries Switzerland CH 61 Power Main unit Remote Thermo Hygro unit Remote Anemometer unit Remote Rain gauge unit Weight Main unit Remote Thermo Hygro unit Remote Anemometer unit Remote Rain gauge unit Dimension Main unit Remote Thermo Hygro unit Remote Anemometer unit Remote Rain gauge unit Appendix use 4 pcs UM 3 or AA 1 5V battery use 2 pes UM 3 or AA 1 5V battery use 2 pcs UM 3 or AA 1 5V battery use 2 pes UM 3 or AA 1 5V battery 231g without battery 65g without battery 315g without battery 290g without battery 185 8 L x 136 9 H x 32 D mm 55 5 L x 101 H x 24 D mm 405 L x 375 H x 160 D mm 163 L x 177 H x 119 D mm DST SU SU SU SU City Codes US and Canadian Cities City Code Zone Offset Atlanta Ga ATL 5 Austin Tex AUS 6 Baltimore Md BWI 5 Birmingham Ala BHM 6 Boston Mass BOS 5 Calgary Alba Can YYC 7 Chicago IL CGX 6 Cincinnati Ohio CVG 5 Cleveland
13. are pressed for 5s the display automatically returns to Pressure and Weather Forecast Mode Viewing the Pressure Temperature Humidity Bar Charts The bar chart on the display can be configured to display the history data for sea level pressure temperature or humidity for channel 1 In Pressure and Weather Forecast Mode press and hold ALARM CHART to toggle the bar chart between Sea level pressure PRESSURE should be displayed Temperature Thermometer icon and CH1 should be displayed Humidity RH icon and CH1 should be displayed Viewing Moon Phase History and Forecast 1 In Pressure and Weather Forecast Mode press MEMORY 2 0 days should be flashing 3 View Moon Phase History Forecast Press UP or DOWN to choose number of days forward days or backward days from current date Press and hold either button for fast advance The corresponding moon phase will be shown 4 To exit press MEMORY Otherwise if no buttons are pressed for 5s the display automatically returns to Pressure and Weather Forecast Mode Understanding the Moon Phase Diagram OOOOO O DVDIO Full moon New moon 48 Understanding the Weather Forecast Display Display Weather Forecast Status ALL Sunny a lt l oS Partly Cloudy dat dot ad A 4 Unstable Weather amp g NOTE 1 The accuracy of a general pressure based weather forecast is about 70 2 The weather fore
14. ature at the anemometer or the temperature adjusted with a wind chill factor The lower left of the wind display indicates the average wind speed for the last 10 minutes as well as gust wind speed alert and gust alert information It can also show records of the maximum values of wind speed and gust attained for the current day The wind speed and gust alert functions can be programmed to sound if the wind speed or gust exceeds a pre configured limit The wind speed may be displayed in km h mph m s or knots Note The wind speed alert has a 5 mph hysteresis and the wind gust speed alert has a 7 mph hysteresis The hysteresis is to prevent the alerts from sounding constantly due to small fluctuations near the alert value This means that after the wind speed reaches the alert value it will have to fall below the alert value plus the hysteresis to deactivate the alert Accessing Wind Mode From the main console unit Press UP or DOWN until the WIND icon EM on the display starts flashing Configuring Wind Display In Wind Mode each press of SET rotates display between Temperature with wind chill wind direction in bearings Temperature with wind chill wind direction in compass points Temperature at anemometer wind direction in compass points Temperature at anemometer wind direction in bearings Setting Units for Wind Speed Display km h mph m s or knots In Wind Mode press and hold SET to convert wind speed units between km h
15. be cleaned on a weekly basis since dirt and debris will affect sensor accuracy Setting up the Thermo Hygro Sensor s 1 Open the latch at the base of the thermo hygro sensor 2 Set the channel with a slide switch 3 Insert two 2 x UM 3 or AA size 1 5V batteries 4 Use a pin to press the RESET key which is in the battery compartment of thermo hygro Sensors 5 Replace the latch and mount unit at desired location Placement tips The thermo hygro sensor should be in an area with free air circulation and sheltered from direct sunlight and other extreme weather conditions Place the unit in a shaded area such as under a roof Avoid placing the sensor near sources of heat such as chimneys Avoid any areas which collect and radiate heat in the sun such as metal brick or concrete structures paving patios and decks Ideally place the sensor above natural surfaces such as a grassy lawn The international standard height for measurements of air temperature is at 1 25m 4 ft above ground level Setting up the Rain Sensor 1 Unlock the funnel shaped top of the rain sensor by turning both knobs on the sides of the rain sensor in an anti clockwise direction 2 Lift the top off the base and insert two 2 x UM 3 or AA size 1 5V batteries into the battery holder 3 Remove the adhesive tape from the see saw 4 Replace the lid and secure into place by turning the knobs clockwise 5 Place the rain sensor in a lo
16. casts It may not necessarily reflect the current situation 3 The Sunny icon as applies to night time implies clear weather 49 2 Clock and Alarm Mode The main console unit can be configured to display the time calendar or UTC time There are three time alarms available on the console unit Single alarm activated once at specified time Weekday alarm activated everyday from Monday to Friday at specified time Pre alarm activated at specified time interval 30 min ahead of weekday alarm if channel 1 temperature falling to 2 C or below The snooze duration for the above alarms can also be programmed 0 15 min Accessing Clock and Alarm Mode From the main console unit Press UP or DOWN until the clock icon beside the time date display starts flashing sae up the Time Date and Language 1 In Clock and Alarm Mode press and hold SET to enter clock and calendar setup 2 The day of week should start flashing in the display Set Language Press UP or DOWN to select language for day of week English German French Italian Spanish or Dutch Press SET to confirm your selection 3 Select City Code Press UP or DOWN to select city code for your local area Refer to P 63 for a list of available codes Press SET to confirm your selection 4 if USR was chosen for city code Set Minute for Latitude You will be asked to enter your latitude in minutes Press UP or DOWN to adjust value Press and hold either button for fast ad
17. cation such that precipitation can fall directly into the sensor ideally 2 3 ft 1m above the ground 6 It may be secured into place by using the four screws provided 7 The sensor must be accurately level for optimum performance To check if the sensor is level remove the lid and check if the ball bearing inside is at the midpoint of the leveler Additionally a bubble level or carpenter s level may be used 8 Attach the protective screen onto the top of the lid The screen will prevent any debris entering the sensor 38 Placement tips The rain sensor should be placed in an open area away from walls fences trees and other coverings which may either reduce the amount of rainfall into the sensor deflect the entry of wind blown rain or create extra precipitation runoff Trees and rooftops may also be sources of pollen and debris To avoid rain shadow effects place the sensor at a horizontal distance corresponding to two to four times the height of any nearby obstruction It is important that rain excess can flow freely away from the sensor Make sure that water does not collect at the base of the unit The rainfall measurement mechanism utilizes a magnet hence do not place any magnetic objects around the proximity of the sensor Setting up the Anemometer wind sensor 1 Plug the wind wheel on the pin at the bottom of the anemometer Please note the shape of the pin With the enclosed Allen wrench tool tighten the scre
18. ding to the polarities shown 3 Reattach the latch 4 If placing the console unit on a table or horizontal surface mount the enclosed table stand 5 If mounting the console unit on a wall or vertical surface use the fitting provided Placement tips Make sure that the console unit is within receiving range of all remote sensors Ideally sensors should be within the line of sight of the console unit Transmission range may be affected by trees metal structures and electronic appliances Test reception before permanently mounting your weather station The console unit measures indoor temperature humidity pressure and receives signals from all remote sensors and radio clock broadcasts Avoid placing the console unit in the following areas Direct sunlight and surfaces which radiate and emit heat Near heating and ventilation devices such as heating ducts or air conditioners Areas with interference from wireless devices such as cordless phones radio headsets baby listening devices and electronic appliances Starting up the Main Console Unit Once the console unit is properly powered the display will start showing some data and weather parameters Wait for a few minutes for the console to finish self calibration and for the sensor readings to show up If is still displayed for the sensor reading s check the wireless transmission path and the batteries for the corresponding sensor 40 Using your Weather Stati
19. h 5 3mph 33 seconds 11 seconds 0 0 to 1999 9 mm 78 73 inch 0 to 19999 mm 787 3 inch 10s 10s English and German 2metres Windows 98 or above 65
20. hr or mm hr Resetting the Rainfall Statistics Memory In Rain Mode press and hold MEMORY to reset all rainfall statistics Setting Units for Rain Display inch or mm In Rain Mode press and hold SET to convert units between mm and inches Activating Deactivating the Daily Rainfall Alert 1 In Rain Mode each press of ALARM CHART rotates display between the current rainfall statistics and the daily rainfall alert ALARM HI will be displayed If the alert is deactivated OFF will be shown otherwise the rainfall alert value is shown 2 When the rainfall alert is displayed pressing UP or DOWN will activate deactivate it Setting up the Daily Rainfall Alert 1 In Rain Mode press ALARM CHART to display rainfall alert 2 Press and hold ALARM CHART until rainfall alert and ALARM HI starts flashing in the display 3 Set Value for Rainfall Alert Press UP or DOWN to adjust value Press and hold either button for fast advance Press ALARM CHART to confirm your selection 4 Upon completion the display will be returned to the rainfall alert display 56 Disabling when Daily Rainfall Alert is Activated To Disable Rainfall Alert Press ALARM CHART to disable the alert 6 Wind Mode The wind direction is shown by an animated compass display Its angle can be displayed as compass points i e NW or in bearings from the north i e 22 5 The upper left of the wind display can be set to indicate the temper
21. in gauges the rain sensor is prone to blockages due to its funnel shape Checking and cleaning the rain sensor from time to time will maintain the accuracy of rain measurements Detach the protective screen and lid Remove any dirt leaves or debris by cleaning the items with soapy water and a damp cloth Clean small holes and parts with a cotton tips or pipe cleaner Look out for spiders or insects that might have crawled into the funnel Also clean the swinging mechanism with a damp cloth 59 Troubleshooting The display shows dashes for weather parameter s The display will show when the wireless link is lost with the remote sensor for the following periods Thermo hygro Sensor 15 minutes Anemometer Wind Sensor 15 minutes Rain Sensor 30 minutes Check or replace the batteries for the corresponding sensor Then press and hold DOWN to enforce a search for all remote signals If the above does not solve the problem check the wireless transmission path from the correspond ing sensor to the main console unit and change their locations if necessary Although wireless signals can pass through solid objects and walls the sensor should ideally be within the line of sight of the console unit The following may be the cause of reception problems Distance between remote sensor and main console unit too long Maximum transmission distance in open area conditions is 100m Signal shielding mate
22. ld ones may leak 6 Use alkaline batteries only Observe correct polarity Low batteries should be changed soon to avoid the damage resulting from a leaking battery Batteries contain harmful acids Wear protective glasses and gloves when handling with leaked batteries Attention Please do not dispose of old electronic devices and used batteries in household waste To protect the environment take them to your retail store or to appropriate collection sites according to national or local regulations 7 Always read the user s manual thoroughly before operating the unit 60 CAUTION The content of this manual is subject to change without further notice Due to printing limitation the displays shown in this manual may differ from the actual display The contents of this manual may not be reproduced without the permission of the manufacturer Remark The front side of the casing shows under certain angles 2 flow lines These flow lines are caused by the production process of the casing and unfortunately are unavoidable They have however no effect whatsoever on the operation of the device EC DECLARATION OF CONFORMITY Product SINUS This product contains the approved transmitter and complies with the essential requirements of Article 3 of the R amp TTE 1999 5 EC Directives if used for its intended use and that the following standard s has have been applied Efficient use of radio frequency spectrum Article 3 2 of the
23. lo Brazil Mexico City Mexico MEX 6 SU Shanghai China Milan Italy MIL 1 SE Singapore Singapore Montevideo Uruguay MVD 3 SM Sofia Bulgaria Moscow Russia MOW 3 SK Stockholm Arlanda Sweden Munich Germany MUC 1 SE Sydney Australia Nairobi Kenya NBO 3 NO Tokyo Japan Nanjing Nanking NKG 8 NO Tripoli Libya China Naples Italy NAP 1 SE Vienna Austria New Delhi India DEL 5 5 NO Warsaw Poland Odessa Ukraine ODS 2 SE Zurich Switzerland Osaka Japan KIX 9 NO DST definition SA Australian DST SB South Brazilian DST Changes annually SC Chile DST SE Standard European DST SG Egypt DST SH Havana Cuba DST SI Iraq and Syria DST SK Irkutsk amp Moscow DST SM Montevideo Uruguay DST SN Namibia DST SP Paraguay DST SQ Iran DST maybe changed annually ST Tasmania DST SU Standard American DST SZ New Zealand DST NO DST no Places that do not observe DST ON Always add 1 hour with local standard time 64 Code OSL PTY PAR PER PRG RGN RKV RIO ROM SSA SCL SPL SHA SIN SOF ARN SYD TKO TRP VIE WAW ZRH Time Zone o DST SE NO SE NO SE NO NO sb SE NO sc sb NO NO SE SE SA NO NO SE SE SE Technical Specifications Weather Station Receivers Receiver Supply 6 0V Ta 23 C RF Transmission Frequency RF Reception Range Barometric Pressure Range At sea level Altitude Compensation Range Barometric Pressure reso
24. lution Barometric Pressure accuracy Outdoor Temperature Display Range Indoor Temperature Display Range Operating Temperature Storage Temperature Temperature accuracy Temperature resolution Humidity Display Range Humidity accuracy Humidity resolution Receiving Cycle Remote Thermo Hygro Rain gauge Wind sensor Sunrise and Sunset Accuracy Wind Direction Range Wind Direction Accuracy Wind Direction Resolution Wind Direction Starting Threshold Wind Speed Range Wind Speed Accuracy Wind Speed Starting Threshold Wind Gust Speed Disply Update Interval Wind Gust Sampling Interval 1h 24h yesterday Rainfall Range Last week last month Rainfall Range Temperature Sensing Cycle indoor Humidity Sensing Cycle indoor CD ROM Cable for the base computer System requirement and Sensor unit Supply 3 0V Ta 23 C 434 MHz 100 meters Maximum Line of Sight 500 hpa to 1100hpa 14 75 inHg to 32 44 inHg 374 5 mmHg to 823 8 mmHg 200m to 5000 m 657 ft to 16404 ft 0 1 hpa 0 003 inHg 0 08 mmHg 5 hpa 0 015 inHg 0 38 mmHg 40 C to 80 C 40 F to 176 F 9 9 C to 60 C 14 2 F to 140 F 0 C to 50 C 32 F to 122 F 20 C to 60 C 4 F to 140 F 1 C or 2 F 0 1 C or 0 2 F 0 to 99 5 1 around 47s 183s 33s 3min latitude within 50 16 positions 11 25 22 5 3mph 0 to 199 9mph 199 9 Km h 173 7 Knots 89 3 m s 2mp
25. on i ci PRESSURE Eu MON vw ALARM CHART Shows time alarms and alerts for temperature rain and wind Press and hold to enter alarm alert setup Press and hold in Pressure and Weather Forecast Mode to view different bar charts HISTORY Shows history for sea level pressure MEMORY Shows records for moon phase temperature humidity rain and wind CHANNEL Changes temperature and humidity display to selected channel Press and hold to enable cycling display of channel temperature and humidity SET Rotates display for current mode Press and hold to enter setup or change units Confirmation for setting parameters Y DOWN Switches to next mode in clockwise direction Decrement for setting parameters A UP Switches to next mode in anti clockwise direction Increment for setting parameters LIGHT SNOOZE Enters Snooze mode when alarm is activated Press to activate backlight for 5 seconds 41 Display Section I Weather Forecast Sunny Partly Cloudy Cloudy Slight Rain Heavy Rain Snow and Unstable Weather conditions Pressure Current or historical pressure mBar hPa mmHg or inHg Altitude or sea level pressure adjustment for atmospheric pressure compensation Pressure trend indication Sea level pressure history for the last 24 hours Sea level pressure history bar chart Moon phase 12 steps of moon symbols Scans moon phase for yea
26. p A searching function is also available which allows the sunrise sunset times for different dates to be viewed 52 Accessing Sunrise Sunset Mode From the main console unit Press UP or DOWN until the sunrise and sunset icons on the lower left of the display start flashing up the Location Data 1 In Sunrise Sunset Mode press and hold SET to enter location data setup 2 The city code in the Time and Alarm display should start flashing Set City Info Press UP or DOWN to select city code for your local area A list of all available cities is enclosed The corresponding longitude and latitude will be shown along with the city Should you wish to input your own geographical coordinates choose USR as the city code Press SET to confirm your selection 3 If USR was chosen you will be asked to input your geographical coordinates Set Degree of Latitude Press UP or DOWN to adjust value Press and hold either button for fast advance Press SET to confirm your selection 4 Repeat above procedure to set minute of latitude degree of longitude minute of longitude time zone of the city and DST selection 5 Upon completion the display will be returned to Sunrise Sunset Mode Note Press and hold SET anytime during the setup to return to normal Clock and Alarm Mode All settings made will be discarded Viewing the Location Data In Sunrise Sunset Mode each press of SET rotates display between Time and sunrise sunset Times
27. perature and Humidity Mode press and hold SET to convert units between degrees Celsius C and degrees Fahrenheit F 54 Activating Deactivating the Temperature Alerts 1 In Temperature and Humidity Mode each press of ALARM CHART rotates channel temperature display between Current Temperature for corresponding channel Upper Temperature Alert displays OFF if deactivated icon displayed Lower Temperature Alert displays OFF if deactivated W icon displayed 2 When the above alerts are displayed pressing UP or DOWN will activate deactivate the corre sponding alert Setting up the Temperature Alerts 1 In Temperature and Humidity Mode press ALARM CHART to select alarm which you wish to configure 2 Press and hold ALARM CHART until channel temperature and A or W icon starts flashing in the display 3 Set Value for Temperature Alert Press UP or DOWN to adjust value Press and hold either button for fast advance Press ALARM CHART to confirm your selection 4 Upon completion the display will be returned to the temperature alert selection screen Disabling when Temperature Alarms are Activated To Disable Temperature Alarm s Press ALARM CHART to disable the alarm s Viewing the Max Min Channel Temperature and Humidity In Temperature and Humidity Mode each press of MEMORY rotates channel temperature and humidity display between Current temperature and humidity at remote sensor Minimum temperature and humidi
28. r 2000 to 2099 Moon phase history for the last or future 39 days Section II Radio Controlled Clock Time and date synchronized by radio signal DCF 77 to atomic clock precision time and date also manually adjustable Clock and Calendar 12hr 24 hr month day or day month Different combinations of clock and calendar displays 6 languages for day of week English German French Italian Spanish Dutch Alarms Single alarm activated once at specified time Weekday alarm activated everyday from Monday to Friday at specified time Pre alarm activated ahead of single or weekday alarm if channel temperature falling to 2 C or below Fixed 30 minutes Programmable snooze function 1 15 minutes Section III Sunrise time and sunset time Calculates sunrise set times with geographical information provided by user DST zone time offset latitude longitude over 133 preset cities can be selected for automatic geographical information input Section IV Temperature and relative humidity with trend indication Indoor and outdoor temperature and relative humidity display C or F Temperature and relative humidity trend indication Dew point display Max and Min memory for temperature and relative humidity Comfort level indicator Analyzes current environmental conditions Comfort Wet and Dry 42 Section V Rainfall measurement Records rainfall amount for the last hour last 24 hours last day
29. r UTC time Display 44 Sunrise Sunset Mode Sunrise and sunset times Longitude and Latitude of local area wee Sunset time Longitude Sunrise time L ou de KA nae eJ Latitude LU l 3 SURRISE Hic SUNSET Sunrise Sunset Icon EE Temperature and Humidity Mode Temperature and humidity trend and readings for indoor and selected channel Comfort level Dew point Temperature alerts Temperature Alert Outdoor Temperature Outdoor Humidity Outdoor Temperature Trend Sensor Battery Status TT 1 Channel and J Th ann i Pa Reception Status gt _ a Hid LIL Outdoor Humidity Trend Cycling Display 21 8 q E LI nome eee Dew point Temperature eo DEN 1 C 4 sl Indoor Humidity Trend 9 Temperature and Humidity Cm am ami Yo Max Min see Mode Icon Comfort Level Indoor Temperature Trend Indoor Temperature Indoor Humidity EM Rain Mode Precipitation amount for last hour last 24 hour yesterday last week and last month Rainfall alert Rain Statistic Rain Icon LAST HOUR rm J ALARM LAST 24 HR Lx YESTERDAY Rain Alert LAST WEEK D J inch LAST MONTH tom mm hr Rain Rate Display Sensor Battery Status Rainfall 45 EI Wind Mode Wind Chill Temperature at place of anemometer Wind direction Wind speed Wind gust Alert for wind speed and wind gust speed Wind icon Sensor Battery Status MA WIND CHILL
30. rials such as metal surfaces concrete walls or dense vegetation in the path of transmission Interferences from wireless devices such as cordless phones radio headsets baby listening devices and electronic appliances The weather readings do not correlate with measurements from TY radio or official weather reports Weather data can vary considerably due to different environmental conditions and placement of weather sensors Check the placement tips included in this manual to site your sensors in the best possible way The weather forecast is inaccurate The weather forecast is a prediction of weather after 12 24 hours and may not reflect current weather conditions PRECAUTIONS This product is engineered to give you years of satisfactory service if you handle it carefully Here are a few precautions 1 Do not immerse the unit in water 2 Do not clean the unit with abrasive or corrosive materials They may scratch the plastic parts and corrode the electronic circuit 3 Do not subject the unit to excessive force shock dust temperature or humidity which may result in malfunction shorter electronic life span damaged battery and distorted parts 4 Do not tamper with the unit s internal components Doing so will invalidate the warranty on the unit and may cause unnecessary damage The unit contains no user serviceable parts 5 Only use fresh batteries as specified in the user s manual Do not mix new and old batteries as the o
31. s the current pressure sea level pressure weather forecast moon phase and pressure trend A number of historical statistics can also be viewed such as the sea level pressure values for the last 24 hours moon phase for the previous and next 39 days as well as a pressure temperature humidity history bar chart Pressure values may be displayed inHg hPa mBar or mmHg and altitude values may be displayed in meters or feet Accessing Pressure and Weather Forecast Mode From the main console unit Press UP or DOWN until the weather forecast icon on the upper left of the display starts flashing Setting Pressure Parameters during Initial Start Up During the initial start up of the main console unit all functions in Pressure and Weather Forecast mode will be locked until the pressure settings are configured 1 Choose Pressure Units The unit icon inHg or mmHg or hPa mBar should be flashing Press UP or DOWN to select pressure unit as inHg hPa mBar or mmHg Press SET to confirm your selection 2 Choose Altitude Units Press UP or DOWN to select altitude unit as feet or meters Press SET to confirm your selection 3 Set Altitude Press UP or DOWN to adjust value Press and hold either button for fast advance Press SET to confirm your selection 4 Upon completion the display will be returned to Pressure and Weather Forecast Mode Note By no input the unit starts flashing and the instrument chooses automatically hPa mBar
32. s transmitted to the main console unit by wireless RF with a range up to 100 meters open area The weather station supports a maximum of 5 thermohygrometers allowing 5 channels of temperature humidity display 36 Contents of Complete Weather Station Kit Before installing your weather station please check that the following are complete Hardware Components Fittings Mounting material Main Console Unit Thermo Hygro Sensor Rain Sensor Funnel shaped Lid with Battery Hatch Sensor Base Bucket See saw Mechanism Protective Screen 4 screws for securing unit to ground Anemometer Wind 4 screws for Sensor securing unit Wind Cups Mounting Wind Vane material Anemometer arm Anemometer base CD ROM 2 m 6 ft Cable for the base computer link 37 Installing your weather station Setting up the Remote Weather Sensors Before starting up the main console unit setup all the remote sensors first When placing the sensors make sure that they are within receiving range of the console unit Ideally they should be within the line of sight of the console unit Transmission range may be affected by trees metal structures and electronic appliances Test reception before permanently mounting your weather station Also make sure that the sensors are easily accessible for cleaning and maintenance The remote sensors should
33. ter link Please read the manual on the CD ROM carefully e Possible storage of 200 sets of data a set of data is a recording of information at that point in time from all sensors e Minimum system requirement Windows 98 or above e Read the software s manual carefully which you will find on the CD 58 Maintenance Changing Batteries The battery statuses of the sensors are checked every hour If the low battery indicators light up replace the batteries for the corresponding unit immediately Changing Batteries for the Main Console Unit 1 Remove the latch at the back and replace all batteries Do not mix old and new batteries 2 Replace the cover Changing Batteries for the Remote Sensors 1 Replace the batteries following the setup instructions for the corresponding sensor 2 When the batteries are properly installed the sensor will resume sending signals to the main console unit To enforce a search immediately for all remote signals press and hold DOWN on the main console unit Cleaning The main console unit and outer casings for the remote sensors can be cleaned with a damp cloth Small parts can be cleaned with a cotton tip or pipe cleaner Never use any abrasive cleaning agents and solvents Do not immerse any units with electronic parts in water or under running water Anemometer Check that the wind vane and wind cups can spin freely and are free from dirt debris or spider webs Rain Sensor Like all ra
34. ty at remote sensor Maximum temperature and humidity at remote sensor Resetting the Max Min Channel Temperature and Humidity Memory In Temperature and Humidity Mode press and hold MEMORY to clear memory for all channels Remote Sensor Status The wave icon above the current channel display shows the connection status of the corresponding remote sensor Icon Status JJ I Searching for remote sensor signals pHi y Corresponding remote sensor successfully linked No signals received for more than 15 minutes 55 Activating Main Console Unit to Search for All Remote Sensor Signals The main console unit may be manually activated to search for signals from all remote sensors Press and hold DOWN to enforce a search 5 Rain Mode The main console unit records the total amount of rainfall for the last hour last 24 hours yesterday last week and last month The rainfall may be displayed in mm or inches A daily rainfall alert function is available which can be programmed to sound if the daily rainfall exceeds a pre configured limit Accessing Rain Mode From the main console unit Press UP or DOWN until the RAIN icon EY on the display starts flashing Viewing Rain Statistics In Rain Mode each press of SET or MEMORY rotates display between different rain statistics Last hour Last 24 hour Yesterday Last week Last month Tip For an estimation of the rain rate the Last Hour rainfall value can be understood as inch
35. vance Press SET to confirm your selection Repeat above procedure to set seconds for latitude minutes for longitude and seconds for longitude 5 if USR was chosen for city code Set Time Zone Press UP or DOWN to adjust value in resolution of 30 min Press and hold either button for fast advance Press SET to confirm your selection 6 if USR was chosen for city code or city is in a DST zone Set Daylight Saving Time Option Press UP or DOWN to turn DST option on or off Press and hold either button for fast advance Press SET to confirm your selection 7 Repeat the above instructions to set year month day calendar display format day month or month day time display format 12 hr 24 hr local hour and local minutes 8 Upon completion the display will return to normal Clock and Alarm Mode Note Press and hold SET anytime during the setup to return to normal Clock and Alarm Mode All settings made will be discarded 50 Rotating between Different Clock Calendar Displays In Clock and Alarm Mode each press of SET rotates clock display between Hour Minute Weekday Hour Minute for UTC Coordinated Universal Time Hour Minute City Hour Minute Second Month Day Year or Day Month Year depending on settings Activating Deactivating the Time Alarms 1 In Clock and Alarm Mode each press of ALARM CHART rotates clock display between Weekday Alarm Time displays OFF if weekday alarm deactivated Single Alarm Time
36. w through the screw hole 2 Open the battery compartment screwed and insert the enclosed batteries 2 x 1 5 V AA or remove the insulation stripe Observe the correct polarity 3 Mount the bracket by using the enclosed mounting material preferably at a mast or on a vertical surface 4 To ensure that the main console unit can display the correct wind direction the wind vane has to be oriented with its head to the north while the complete wind vane is in line with the anemometer s arm fin is in line with the anemometer s arm tip shows to the other direction Use a compass if necessary Note If it is not possible to place the anemometer s arm to the north as provided by default the wind direction has to be adjusted manually I Observe the correct polarity of the batteries II Point the wind vane towards the north If necessary use a compass for a precise input IIL Use a pin to press the SET key which is in the battery compartment of the wind sensor Attention Above procedure must be repeated when changing batteries Placement tips Check that wind can travel freely around the anemometer and is not distorted by nearby buildings trees or other structures The official mounting location for anemometers is 10m 33 ft above ground level in a clear unobstructed location 39 Setting up the Main Console Unit 1 Open the latch at the back of the main console unit 2 Insert 4 x UM 3 or AA size 1 5V batteries accor
Download Pdf Manuals
Related Search