Saeco Exprelia HD8854
Contents
1. At the end of the dispensing phase remove the container and place it under the hot water wand Press the SPECIAL button Dispensing can be interrupted by pressing the STOP button At the end remove the container and empty it Repeat the process from step 5 to step 7 until the water tank is empty Select the product by pressing the button shown SPECIAL BEVERAGES HOT WATER Select HOT WATER by pressing button A or V Press the OK button and wait for the programmed quantity to be dispensed Fill the water tank with fresh drinking water as previously described Your machine is now ready to brew excellent beverages INTENZA WATER FILTER To improve the quality of the water you use and extend the life of your machine at the same time it is recommended that you install the water filter After installation go to the water filter initialization programme see the MACHINE MENU page 25 In this way the machine informs the user when the water filter must be replaced Remove the water filter from its packaging immerse it vertically with the opening positioned upwards in cold water and gently press its sides to let the air bubbles out Remove the small white filter from the Set up the Intenza Aroma System Insert the filter in the empty tank The tank and store it in a dry place sheltered A Soft water reference mark and the groove must from dust B Medium water standard match2. Register your product and get support at www philips com welcome EXPRELLA Type HD8854 HD8856 OPERATING INSTRUCTIONS READ THESE OPERATING INSTRUCTIONS CAREFULLY BEFORE USING THE MACHINE PHILIPS Saeco IMPORTANT SAFEGUARDS When using electrical appliances basic satety precautions should always be tollowed including the following l 2 3 d d Read all instructions Do not touch hot surtaces Use handles or knobs To protect against tire electric shock and injury to persons do not immerse cord plugs or appliance in water or other liquid Close supervision is necessary when the appliance is used by or near children Unplug trom outlet when not in use and before cleaning Allow to cool betore putting on or taking off parts and betore cleaning the appliance Do not operate any appliance with a damaged cord or plug or after the appliance maltunctions or has been damaged in any manner Return appliance to the nearest authorized service facility for examination repair or adjustment The use of accessory attachments not recommended by the appliance manufacturer may result in fire electric shock or injury to persons Do not use outdoors Do not let cord hang over edge of table or counter or touch hot surfaces 10 Do not place on or near a hot gas or electric burner or in a heated oven ll Always attach plug to appliance first then plug cord into wall outlet To disco
3. iz E Select the menu option Press the OK button to confirm Fill the water tank with fresh drinking Press the OK button to confirm water and then press the OK button INSERT GROUP CLEAN TAB Insert the cleaning tablet into the bypass After inserting the tablet press the OK Place a container under the coffe doser button dispensing spout PLACE A CONTAINER BREW GROUP CLEAN UNDER THE DISPENSING SPOUT EN ool MENU L LA After placing the container press the The cleaning cyde for the brew group is At the end of the cycle remove the OK button performed automatically container and empty it appropriately After the cycle return the SBS dial to the desired position see page 8 BOILER DESCALING CYCLE MENU Descaling should be performed every 1 2 months or when the machine displays the relevant message The machine must be on to perform this cycle it automatically controls the distribution of the descaling solution In case of conflict priority must be given to what is indicated in the operation and maintenance manual over the instructions provided on separately sold accessories and materials DO NOT LEAVE THE MACHINE UNATTENDED DURING THIS OPERATION WARNING NEVER USE VINEGAR AS A DESCALING SOLUTION Only use the Saeco descaling solution especially designed to respect the technical features of the machine to ensure its performance will not decrease with time and for a safe and risk free use
4. If a long detachable power supply cord or extension cord is used l The marked electrical rating of the detachable power supply cord or extension cord should be at least as great as the electrical rating of the appliance 2 It the appliance is of the grounded type the extension cord should be a grounding type 3 wire cord and 3 The longer cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over EB CARAFE ASSEMBLY PROCEDURE For correct use of the carafe refer to the instructions on page 12 The maintenance instructions for the carafe circuits are described on page 34 The disassembly and cleaning instructions for the components are described on page 39 A THOROUGH SANITATION AND CLEANING OF THE CARAFE ENSURES CORRECT OPERATION AND PREVENTS THE 1 THOROUGHLY CLEAN THE CARAFE AT FIRST USE AND AFTER A LONG PERIOD OF INACTIVITY PROLIFERATION OF BACTERIAL LOADS WHICH MAY BE HARMFUL FOR HUMAN HEALTH GENERAL INEORMAVION siset ris uini qUdY WES eqq ues aped Arredo heed aire eM e 2 MACHINE COMPONENTS amp ACCESSORIES CONTROL PANEL seen I 3 Ey ee re PRad ri 4 STARTING THE MAGHING casarem inea e E EAE E aM bRUU MM M EIU DNE 4 SETTING THE LANGUAGE S oiii E ee 5 MEASURING HEWAN R HARDNESS iepen ginere annain EEEE ET EN EEE E DU CEUUES 5 FIRST USE USE AFTERA PERIOD UE INACTIVE V csosuaas cepit d qur tuoi tta d dude fud 6 Jal p WATER F
5. The descaling solution is to be disposed of according to the manufacturer s instructions and or regulations in force in the country of use Note Before starting a descaling cycle make sure that 1 THEINTENZA WATER FILTER HAS BEEN REMOVED 2 container of adequate size or a couple of containers are available and are placed in the points identified DESCALING AND OR RINSE CYCLES CANNOT BE STOPPED ALL THE PHASES MUST BE COMPLETED IF THE MACHINE IS SWITCHED OFF OR IN CASE OF POWER FAILURES THE INTERRUPTED CYCLE MUST BE REPEATED FROM THE BEGINNING HOWEVER CYCLES MAY BE PAUSED BY PRESSING THE PAUSE BUTTON IT WILL BE POSSIBLE TO RESUME THE CYCLE AT ANY TIME BY PRESSING THE START BUTTON TURN THE SBS DIAL ALL THE WAY TO THE LEFT COUNTER CLOCKWISE SEE PAGE 8 BEFORE STARTING THE CYCLE To correctly prepare the descaling solution pour the entire content of the Saeco concentrated descaling solution into the water tank and then fill the tank with fresh water up to the MAX level Note During the descaling cycle some alarm messages may appear to allow for a correct management of the machine After resetting the message always press the START button to resume the descaling cycle MAINTENANCE START DESCALING FILL TANK WITH CARAFE CLEANING DESCALING SOLUTION DESCALING CARAFE CLEAN OK V Select the menu option Warning Once this selection is made the Refill water tank with descaling solution Press the OK button to confirm
6. whole cyde will have to be completed Press the OK button to confirm Press the OK button to confirm or ESC to exit E MAINTENANCE FILL HALF CARAFE WITH WATER INSERT IN BREW POSITION EMPTY TRAY UNDER BREW GROUP OK OK DES MENU mee al AD IN Empty the drip tray placed under the dispensing spout page 36 fig 2 and then replace it on the machine Then press the OK button Fill half the carafe with fresh water page 34 fig 7 Insert the carafe and place it in the brewing position Then press the OK button STEP 1 2 DESCALING STEP 1 2 DESCALING EN DERE MENU Cv JCoK JUESC U The descaling cycle is activated The bar shows the cycle s progress If the containers need to be emptied press the PAUSE button Then press the START button when the container has been emptied and replaced PLACE A CONTAINER UNDER HOT WATER amp CARAFE DISP SPOUT OK onol MENU Cv JOE EC a Place a container under the dispensing spout and a container under the hot water wand Then press the OK button RINSE TANK amp FILL WITH WATER OK DES MENU At the end of the first step when the descaling solution is finished the machine will require a tank rinse A default amount of water is needed for the rinsing step This allows performing an ideal rinse cycle to ensure the best conditions to brew products The message about filling the tank for the rinse cycle
7. Push firmly until it is completely C Hard water inserted WATER MENU ENABLE FILTER ACTIVATE FILTER Fill the tank with fresh drinking water Place a container beneath the hot water Access the MACHINE MENU see and re insert it into the machine steam wand page 25 Select WATER MENU and ACTIVATE FILTER then press OK ACTIVATE FILTER INSERT FILTER PLACE A CONTAINER FILL THE TANK UNDER THE WATER SPOUT Press the OK button Press the OK button to confirm the Press the OK button to confirm Wait introduction of the new water filter until the cycle is completed and remove the container NOTE At the end of the procedure the display automatically returns to the product dispensing page If the Intenza water filter is not available insert the small white filter previously removed see point 1 into the tank ER ADJUSTMENTS COFFEE STRENGTH SBS The SBS dial has been carefully designed to give your coffee the fullness and intensity you desire Simply turn the dial and set the coffee from mild intensity to strong intensity according to your own taste SBS SAECO BREWING SYSTEM The Saeco Brewing System SBS adjusts the fullness of the brewed coffee The coffee may even be adjusted while brewing This adjustment has an immediate effect on the selected type of brewing MEDIUM COFFEE MILD COFFEE STRONG COFFEE OPTI DOSE ADJUSTS THE AMOUNT OF COFFEE TO GRIND The mach
8. coffee is poured into the bypass doser only water will be dispensed If the dose is excessive or if 2 or more scoops of coffee are added the machine will not brew the product and the coffee in the bypass doser will be discharged into the used grounds drawer EP ESPRESSO ER Gr CAFFE LUNGO SPECIAL Select the product desired by pressing the corresponding button INSERT GROUND COFFEE AND PRESS OK OK ESC Press OK to start brewing KI cappuccino PRODUCT BREWING STEAM RISK OF SCALDING ALWAYS WAIT FOR THE CYCLE TO END BEFORE REMOVING THE CONTAINER i AT THE BEGINNING OF THE DISPENSING PHASE THE MACHINE MAY PRODUCE SOME SPURTS OF MILK AND REFER TO THE SECTION MILK CARAFE USE SEE PAGE 12 Place the cup or the container where the milk based product will be prepared CAPPUCCINO C PLEASE WAIT DERE MENU The machine starts brewing it grounds the coffee and warms up to dispense milk In this case the ECOMODE function is set to ON see page 26 Rotate the handle upper part of the container on the cup To avoid spilling milk always use cups of adequate size Milk dispensing begins This operation can be stopped by pressing STOP Select the desired milk product by pressing the corresponding button you can select only one milk product at a time CAPPUCCINO WS Once milk has been dispensed the machine starts brewing the coffee This operation can be stopped b
9. cycle allowing for a thorough cleaning This wash completes the maintenance process of the milk carafe We recommend carrying out this cycle on a monthly basis using Saeco cleaning solution which can be purchased from Saeco Customer Service or an authorized dealer WASH CYCLES CANNOT BE STOPPED DO NOT LEAVE THE MACHINE UNATTENDED DURING THIS OPERATION REFILL WATER TANK MAINTENANCE START CARAFE BREW GROUP CLEAN WASHING CARAFE CLEANING DESCALING OK Select the menu option Press the OK button to confirm Fill the water tank with fresh drinking Press the OK button to confirm water Press the OK button to confirm The carafe must be removed from the Press on the sides and lift the lid Fill the carafe with fresh drinking water machine and its content emptied up to the MAX level Disengage the handle by rotating it Add the content of a detergent packet to clockwise the milk carafe gt in KS gt A H vn Ae W e e E j E Place the lid back and ensure that it is Move the handle back to its central Insert the carafe inclined towards the closed correctly position to allow for perfect closure front The carafe base should be positioned on the hole E located on the drip tray At this stage the carafe holes A are lower than the couplings C The carafe pins B are located at the same height of the guides D The carafe will be naturally back in place CARAFE CL
10. d enn t b ttp ote neta 37 Jus GROUP CLEANING m 38 MILK e tries Cnm 39 AIK CARAFE ASSEMBID C 40 MACHINE WARNINGS EE d SAFETY EE 43 GENERAL INFORMATION This coffee machine is suitable for preparing espresso coffee using coffee beans and is equipped with a device to dispense steam and hot water The machine is designed for domestic use and not suitable for heavy or professional use Warning No liability is held for damage caused by e Incorrect use not in accordance with the intended purposes e Repairs not carried out by authorized service centers e Tampering with the power cord e Tampering with any parts of the machine e Use of non original spare parts and accessories e Failure to descale the machine or machine use at temperatures below 32 F 0 C IN THESE CASES THE WARRANTY SHALL BE DEEMED NULL AND VOID THE WARNING TRIANGLE INDICATES ALL N IMPORTANT INSTRUCTIONS FOR THE USER S SAFETY PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY TO PREVENT SERIOUS INJURIES ER GENERAL INFORMATION TECHNICAL DATA HOW TO USE THESE INSTRUCTIONS Keep these operating instructions in a safe place and make them available to anyone else who would use the coffee machine For further information or in case of problems please refer to the an authorized service center For Saeco customer service call 800 933 7876 in the U S or 514 385 5551 in Canada SAVE THESE INSTRU
11. filter in a cool area in which the room temperature ranges from 1 C to 50 C 34 F to 122 F Do not store it in direct sunlight 2 Carefully read the operating instructions and the safety warnings provided with each filter 3 Keep the filter instructions together with the manual 4 These instructions integrate those contained in the manual as they focus on the specific application of the filter in the machine EC DECLARATION OF CONFORMITY YEAR 09 EC 2006 95 EC 2004 108 SAECO INTERNATIONAL GROUP S P A Via Torretta 240 40041 Gaggio Montano Bo Italy declare under our responsibility that the product AUTOMATIC COFFEE MAKER HD8854 HD8856 to which this declaration relates is in conformity with the following standards or other normative documents e Safety of household and electrical appliances General requirements EN 60335 1 2002 A1 2004 A2 2006 A11 2004 A12 2006 A13 2008 e Safety of household and electrical appliances Part 2 15 Particular requirements for appliances for heating liquids EN 60 335 2 15 2002 A1 2005 A2 2008 e Household and similar electrical appliances Electromagnetic fields methods for evaluation and measurement EN 62233 2008 e Household and similar electrical appliances safety Part 2 14 Particular requirements for kitchen machines EN 60335 2 14 2006 A1 2008 e Electromagnetic compatibility EMC Requirements for household appliances electric tool
12. is normal as it is part of the procedure RINSE TANK amp FILL WITH WATER EMPTY TRAY UNDER BREW GROUP OK Rinse the water tank and refill it with fresh drinking water Then press the OK button Empty the drip tray placed under the dispensing spout page 36 fig 2 and replace it back onto the machine Then press the OK button FILL HALF CARAFE WITH WATER INSERT IN BREW POSITION OK Completely empty the carafe page 34 fig 7 and fill it with fresh water Insert the carafe in the brewing position and then press the OK button PLACE A CONTAINER UNDER HOT WATER amp CARAFE DISP SPOUT EN OK STEP 2 2 RINSING PESE MENU PERS MENU Ey al N Place a container under the dispensing spout and a container under the hot water wand Then press the OK button The rinse cycle is activated The bar shows the cycle progress EXPRELIA OOO DES MENU At the end of the second step the machine is ready for use If the containers need to be emptied press the PAUSE button Then press the START button when the container has been emptied and replaced All the components should then be rinsed After rinsing them dry them carefully and fit them back into their seats Set the SBS dial to the desired position see page 8 TB MAINTENANCE MILK CIRCUIT MAINTENANCE It is possible to sanitize the milk circuits by carrying out a simple and quick
13. on this length will be applied to the brewing of this beverage For the other beverages hold pressed the button of the beverage to be programmed and follow the same procedure EI BEVERAGE MENU All beverage settings can be customized MENU EXPRELIA MACHINE MENU vol M ZO i T Ic d idi Press the MENU button to access the Press the OK button to access the machine main menu BEVERAGE MENU Fb EI e ESPRESSO B EVE R AG E M z N U CAPPUCCINO CAFFE CAFFE LUNGO CAFFE LUNGO SPECIAL CE Scrolling Selection button Scrolling Selection button Selection confirmation button Exit button For each beverage it is possible to reset the original factory settings After selection of this DEFAULT function the customized settings are deleted In this case we look at how to programme a customized cappuccino The milk managing options are not shown when a coffee brewing espresso or long coffee is being programmed Fb ESPRESSO gt d CAFFE LUNGO SPECIAL COFFEE QUANTITY PREBREWING COFFEE TEMPERATURE COFFEE LENGTH K3 CAPPUCCINO CAPPUCCINO COFFEE QUANTITY PREBREWING COFFEE TEMPERATURE ad amp MENU This section allows you to program the quantity of coffee to grind for the beverage brewing this setting will affect the coffee aroma GROUND COFFEE The beverage is brewed by using the pre ground coffee MILD mild dose MEDIUM medium dose STRONG strong dose Preb
14. open 2 The stand by activation time can be changed in the MACHINE MENU on page 26 A 3 When the stand by mode is activated the machine performs a rinse cycle of the internal circuits if necessary The cycle can be interrupted by pressing the STOP button The machine can be turned on again by executing one of the following actions 1 By pressing any of the control panel buttons 2 By opening the service door when closing the door the machine goes back to The red light flashes when the machine stand by mode is in stand by mode KO MILK CARAFE USE The machine is equipped with a carafe allowing for optimal milk frothing for the brewing of tasty cappuccinos latte macchiatos and any milk based beverage Note Before using the carafe make sure it is thoroughly clean and sanitary If milk is left in the carafe make sure it is still suitable for food consumption before using it The container allows for an easy and practical steaming and frothing of milk The container can be easily removed from the machine after each use so that it can be placed back in the refrigerator The brewing circuit is automatically washed by an automatic cleaning cycle after each use This automatic cleaning cycle works only if active see page 29 and can be also manually started by pressing the CLEAN button next see page 17 The carafe must be removed at least once a week to allow for proper cleaning of all components and keep all parts fres
15. ARECCHIO 1 Water tank cover 15 Liquid recovery tray cover 2 Pre ground bypass doser 16 Service door button 3 Service door 17 Power button 4 SBS dial 18 Power cord connector 5 Hot water steam wand 19 Milk carafe 6 Full drip tray indicator 20 Pre ground coffee measuring scoop 7 Coffee bean hopper with lid 21 Water hardness test strip 8 Grinder adjustment 22 Brew group lubricant 9 Control panel 23 Descaling solution 10 Milk container couplings 24 Brew group cleaning tablets 11 Dispensing spout 25 Power cord 12 Drip tray grill sealed support 26 Intenza water filter 13 Brew group 27 Cleaning brush 14 Used grounds drawer protection element 28 Carafe coupling cap CONTROL PANEL The control panel has been designed to allow an ergonomic use of all machine functions Espresso button Coffee button Cappuccino button Opti dose button MENU button ESPRESSO CAPPUCCINO EXPRELIA m OOO CAFFE LUNGO SPECIAL Q U e Function buttons Special beverage button Carafe cleaning cycle button Long Coffee button Stand by button EN INSTALLATION STARTING THE MACHINE Before turning on the machine make sure that the power button is set to 0 as 1 Lift the right outer lid and remove the Slowly pour coffee beans into the gl Lift the left outer lid and remove the inner lid hopper inner lid Replace the inner lid and close the outer lid Fill the tank with fresh drinking water Do Ins
16. CTIONS INSTRUCTIONS FOR THE POWER SUPPLY CORD e A short power supply cord is provided to reduce risks resulting from becoming entangled in or tripping over a longer cord e Extension cords may be used if care is exercised in their use If an extension cord is used make sure The marker electrical rating of the extension cord should be at least as great as the electrical rating of the appliance b The extension cord should be arranged so that it will not drape over the counter top or table top where it can be pulled on by children or tripped over c Ifthe appliance is of the grounded type the extension cord should be a grounding type 3 wire cord e Do not use multi sockets TECHNICAL DATA Nominal voltage See label on the appliance Power rating See label on the appliance Power supply See label on the appliance Shell material Thermoplastic material Metal Size wx hx d 245 x 360 x 420 mm Weight 13 4 Kg Class 14 2 Kg Class Cord length 1200 mm Control panel Front Water tank 1 5 liters removable Coffee bean hopper capacity 300 grams Pump pressure 15 bar Boiler Stainless steel Coffee grinder Ceramic Quantity of ground coffee 7 10 59 Dregdrawer capacity about 11 Safety devices Boiler pressure safety valve Double safety thermostat MACHINE COMPONENTS AND ACCESSORIES CONTROL PANEL ER The references of this table are reported in the attached carton paper in which the components are illustrated COMPONENTI APP
17. Close or correctly place the coffee bean hopper inner cover to be able to prepare a beverage Fill the coffee bean hopper with coffee beans Insert the brew group back in place Insert the coffee grounds drawer and the drip tray Remove the used grounds drawer and empty the coffee grounds into a suitable container Note The used grounds drawer must be emptied only when the machine requires it and with the machine on If you empty the drawer with the machine turned off it will not record the emptying operation Close the service door to make the machine functional Take out the tank and fill it with fresh drinkable water or top it up by means of the special port Open the service door and empty the drip tray located under the brew group Warning If this operation is performed when the machine is on it will record the used grounds drawer emptying and will reset the counter therefore it is necessary to empty the coffee grounds as well Help Message Displayed TURN CARAFE INTO BREWING POSITION ESC ERE MENU TURN CARAFE INTO RINSING POSITION ESC alle MENU INSERT CARAFE ESC alle MENU OOO alle MENU EXPRELIA OOD alle MENU CAPPUCCINO a ij RESTART TO SOLVE ES MENU EUR MACHINE WARNINGS How to Reset the Message A beverage with milk has been selected The machine requires the carafe handle spout to be placed into dispensing position Press the button ESC to cancel the se
18. EANING EN PESE MENU JAN Cy JLok JLESC I The cleaning cyde is activated The bar shows the cycle progress K 4 Place a large empty container under the dispensing spout Rotate the upper part of the milk carafe directly above the container 91 A Insert the carafe by turning it towards the base through a round movement as shown in the figure until it is hooked to the hole E located in the drip tray POUR DETERGENT INTO CARAFE amp FILL WITH WATER N Place a large empty container under the Press the OK button to confirm dispensing spout Rotate the upper part of the milk carafe directly above the container REFILL FILL CARAFE WATER TANK WITH FRESH WATER OK Cv ITA i BC A At the end of the wash fill the tank with Remove the carafe rinse and refill it with fresh drinking water Press the OK fresh drinking water button to confirm Press the OK button to confirm CARAFE RINSING Upon completion of the cleaning EN 1 cycle we recommend rinsing all the components under fresh drinking water DERE MENU d The rinse cycle is activated The bar shows the cycle progress At the end of the cycle the machine returns to the product brew menu page EI CLEANING MAINTENANCE DURING OPERATION During normal operation the following messages may appear Empty coffee grounds drawer and or Empty drip tray This operation must be performed when the machine is on
19. ILTE T L Q 7 ADJUSTMENTS idera pa XY capaneot HE HE UE SERE EAE ERE OR TERR RECTE OP ERE SR bt 8 COFTEESTRENGER SAECO BREWING SYSTEM pasenie tusE sea EESE E P dr eium US niin 8 OPTIEDOSE ADJUSTS THE AMOUNT OPCOPFEETO GRIND icusasnsash aesti rada arauuatbtataniop vdd arcet 8 SAECOADAPTING SYSTEM T 9 COGEEEGRINDER ADIUSTIMEN Tyre concnns tometer nein EEN 9 DISPENSING SPOUT HEIGHT ADJUSTMENT s cuwonsasnesvnoraiatshiahensageu eub erbe qe teg Ens 10 BEER 11 MIEK CARAPE USE cessit te zhEESERE EEECH UE OR REED E URP S EYEUEREKVOR REIP UR Tr e TP IER 12 COFFEE BREWING ioca citri nmm Lp ln P oS eent oreet eed ae eh bas 14 Po PRES S07 GOREEETEONG COFTEE mron pirina EE E E E E E EEE E T 14 BEVERAGE BREWING WITH PRE GROUND COFFEE esses 15 CAPPUCCINO M m 16 CLEANING CICUE getest AE EE Eege 17 SPECIAL EE E Eege NEE e ENEE Ee RREDEREE PES SE SES 18 SPECIALS BUTTON eebe 18 Pi MAC HIATO ere 19 JE MILK 19 HOT WATER P E 20 STEAM M HHU 20 BEVERAGE LENGTH QUICK PROGRAMMING cesse 21 BEVERAGE MENU usui mi mari nr lol pi pU EEUU RR donde or Eie oh dps 22 MACHINE MENU so Rica CE SPESE UE R EE 25 MAINTENANCE TTT 30 gii eww00 Gw9 n Ee 36 MAINTENANCE DURING OPERATION csse HH me 36 GENERAL MACHINE CLEANING cicssidedwvaceount A tera erm PER
20. Press the button and open the service Remove the drip tray and used grounds Empty the used grounds drawer and door drawer wash it with fresh water Empty and wash the drip tray and the Correctly reinstall all the components Insert the tray and the coffee grounds cover with fresh water drawer and close the service door If the used grounds drawer is emptied when the machine is off the coffee grounds counter is not reset For this reason the machine might display the Empty coffee grounds drawer message after brewing just a few coffees GENERAL MACHINE CLEANING The cleaning procedure described below must be carried out at least once a week Note If water remains in the tank for several days do not use it WARNING Never immerse the machine in water Turn off the machine and unplug it Take out the water tank and wash it with Take out the water recovery tray fresh water Remove the support under the grill Wash it taking care of the seal area Reinstall drying it reassemble and reinsert it in the support only after washing the inside the machine of the water recovery tray Clean the pre ground bypass doser with Clean the steam wand and the display it with water a dry cloth with a dry cloth EI CLEANING BREW GROUP CLEANING Wash the brew group at least once a week Before removing the group remove the used grounds drawer as shown in fig 2 on page 36 Wash the brew group with lukewarm water Lubric
21. Remove the suction hose Remove the external fitting by pulling it Remove the internal fitting All components can be thoroughly washed with hot water After washing the components reassemble them by following the instructions on next page E cLeANiNG MILK CARAFE ASSEMBLY Pay attention during the assembly phase In case the components do not smoothly enter in their positions read the instructions more carefully and repeat the assembly procedure Note The inner side of the service door shows a quick guide on how to reassemble the carafe p Insert the inner fitting in the hose and Insert the outer fitting in the inner Insert the hose in the outer fitting press until fully inserting it fitting Refer to the arrow in the figure for the direction of insertion Insert the unit previously assembled Rotate the handle clockwise up to the in the cover base Pay attention to the 855 symbol reference Ti Fit the cover on the carafe Rotate the handle anti clockwise to The carafe is now ready for use bring it to the locked position Help Message Displayed CLOSE HOPPER DOOR all MENU ADD COFFEE sl MENU INSERT BREW GROUP PESE MENU INSERT COFFEE GROUNDS DRAWER wal MENU EMPTY COFFEE GROUNDS DRAWER aide MENU CLOSE FRONT DOOR onl MENU REFILL WATER TANK ESSE MENU EMPTY DRIP TRAY aide MENU MACHINE WARNINGS ETE How to Reset the Message
22. Then pull until it releases After use remove the container from the machine and place it in the refrigerator for proper conservation We recommend NOT to keep the container at room temperature for too long Maximum 10 minutes Store the milk according to producer s instructions and do NOT use it after best before date Wash the container as described in the MILK CARAFE CLEANING section see page 39 Insert the carafe by turning it towards the base through a round movement as shown ETE corre BREWING ESPRESSO COFFEE LONG COFFEE This procedure shows how to brew an espresso To brew another type of coffee press the appropriate button Use proper coffee cups to prevent coffee from spilling To brew 2 cups press the button twice the machine brews half of the entered quantity and briefly interrupts dispensing in order to grind the second coffee dose Coffee brewing is then restarted and completed Sy ESPRESSO cies L5 CR me CAFFE LUNGO SPECIAL Position 1 or 2 cups to brew one or two Position 1 or 2 cup s to brew an espresso Choose the beverage by pressing the espresso coffees or a long coffee corresponding button once for 1 cup and twice for 2 cups A uw lis E d te ESPRESSO ESPRESSO 00 Ld o0 EN DERE MENU DES MENU LS TOA The machine starts grinding the selected The machine begins brewing the coffee quantity selected beverage ESPRESSO Coffee brewing can be stopped at any time b
23. ase Wait until it is completed RINSING EN STOP MES MENU EXPRELLA OOO PESE MENU Cv Jlok JLESC U A P Cv Lok JLEsC L A When warm up phase is complete the A small quantity of water is dispensed The machine is now ready for use machine performs a rinsing cycle of the Wait for this cycle to be completed internal circuits It is possible to interrupt automatically the cycle by pressing the STOP button MEASURING THE WATER HARDNESS The test strip can only be used for one measurement Intenza Aroma System A B By Ki d Machine water hardness setting Immerse the water hardness test strip Check the water hardness value and set provided with the machine in water for The machine water hardness level page 28 1 second The Intenza Aroma System page 7 RN INSTALLATION FIRST USE USE AFTER A PERIOD OF INACTIVITY To improve the product quality carry out this procedure at first use of the machine and after long periods of inactivity A few simple operations are needed to ensure the quality of your favourite beverages over time MENU TES J 2x CAFFE LUNGO Place a container of large size under the coffee dispensing spout INSERT GROUND COFFEE AND PRESS OK OK ESC Cv JLoRMTesc A gt Press the OK button to start dispensing water through the dispensing spout DO NOT insert coffee at this stage Press the button once or more until the icon is displayed SPECIAL
24. ate the brew group after approximately 500 brewing cycles The brew group lubricant may be purchased from an authorized service center WARNING Do not wash the brew group with detergents that may compromise its correct operation Do not wash it in the dishwasher WW Press the PUSH button to remove the Wash the brew group and the filter and Lubricate the brew group guides using brew group dry the supplied lubricant Apply the lubricant evenly on both side Make sure the brew group is in rest Make sure the components are in the guides position the two references must match correct position The hook shown must be in the correct position to check its position firmly press the PUSH button The lever on the rear part of the group Insert the washed and dried brew group Insert the used grounds drawer must be in contact with the group DO NOT PRESS THE PUSH BUTTON and close the service door base MILK CARAFE CLEANING The carafe must be removed and properly washed at least once a week This procedure guarantees the perfect sanitation of all components Note Pay attention to how the components are assembled This little shrewdness will facilitate the subsequent reassembling Disengage the handle by rotating it clockwise Rotate the handle co unter clockwise to Remove the connector which is in Remove the handle with the suction the unlock position contact with the machine hose
25. eaning milk carafe now ready for use involves the lines in contact with the Cycle milk and it is carried out independently ofthe presence of milk in the container KI SPECIAL BEVERAGES SPECIAL BEVERAGES The machine is designed to brew other beverages not displayed on the main menu Note If no product is selected the machine goes back to the main menu STEAM HOT WATER WAND MAY REACH HIGH TEMPERATURES DO NOT TOUCH WITH BARE HANDS USE THE 1 WARNING DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER AND SCALDING IS POSSIBLE THE APPROPRIATE HANDLE ONLY SPECIAL BEVERAGES SPECIAL BEVERAGES LATTE MACCHIATO LATTE MACCHIATO HOT MILK HOT MILK HOT WATER HOT WATER WS y S DES MENU TS Press the button to access the menu The display shows the page for Select the desired beverages by pressing SPECIAL beverages button X or V See the following sections to brew a special beverage Note The machine goes back to the main menu after 10 seconds SPECIAL BEVERAGES HOT WATER When the desired beverage has been selected press OK to start preparation To brew latte macchiato or hot milk refer to the section on how to prepare a cappuccino for the brewing sequence and the cleaning details see page 16 and 17 LATTE MACCHIATO This specific programme allows brewing a latte macchiato SPECIAL BEVERAGES _ LATTE MACCHIATO HOT MILK HOT WATER Place the cup Rotate the upper part of A
26. ed language is displayed This menu allows you to set the menu language and the display brightness This setting is of fundamental importance for correctly adjusting the BRIGHTNESS To set the correct display brightness according to the room illumination parameters of the machine according to the country where the machine is used EI MACHINE MENU WATER MENU WATER MENU HARDNESS ENABLE FILTER ACTIVATE FILTER This menu allows setting correct water parameters for coffee brewing To change the machine water hardness setting The Hardness function allows adjusting the machine to the level of hardness of the water used The machine will then request descaling at the right moment Measure water hardness as shown on page 5 To activate deactivate the warning signal to replace the water filter By activating this function the machine notifies the user when the water filter needs to be replaced OFF Warning disabled ON Warning enabled this value is automatically set when the filter is activated To activate the filter after its installation or replacement Refer to the relevant section on page 7 to correctly install and or replace the filter MAINTENANCE MAINTENANCE This menu allows setting all the functions for correct machine maintenance COUNTERS BREW GROUP CARAFE CLEANING DESCALING CARAFE CLEAN FACTORY SETTINGS This function shows how many products have been brewed for every s
27. ert the plug into the socket located not exceed the max level indicated on on the back of the machine and insert the water tank Place the water tank back the other end into a power outlet with into the machine suitable current When the correct temperature is reached the machine performs a priming and rinsing cycle of the internal circuits A small amount of water is dispensed Wait for this cycle to be completed The screen for product dispensing Press the power button to the I The display shows a red flashing led appears on the display see page 3 position to turn the machine on Press the stand by button to start the machine At first start up only the screen 1 will be displayed as shown on page 5 Then the language can be set from the relevant menu only see page 25 SETTING THE LANGUAGE This setting allows you to choose the operating language of the machine It also allows you to adjust the parameters of the beverages to the typical parameters of the country where the machine is used This is why some languages are differentiated also by country If no language is selected you will be requested to select it the next time the machine is started LINGUA LINGUA HEATING UP ITALIANO ITALIANO T 7 ENGLISH ENGLISH DEUTSCH DEUTSCH vol MENU N due MENU l Ee Select the desired language by pressing Press the save button The machine activates the warming up the arrow buttons X or V ph
28. fter selecting LATTE MACCHIATO press the container handle on the cup OK HOT MILK This specific programme allows brewing hot milk SPECIAL BEVERAGES LATTE MACCHIATO HOT MILK HOT WATER e E uz f d Place the cup Rotate the upper part of After selecting HOT MILK press OK the container handle on the cup H ll d At the end of the brewing procedure take the cup with the latte macchiato T At the end of the brewing procedure take the cup with the milk El sPeCIAL BEVERAGES HOT WATER DISPENSING WARNING DISPENSING MAY BE PRECEDED BY SHORT SPURTS OF HOT WATER AND SCALDING IS POSSIBLE THE STEAM HOT WATER WAND MAY REACH HIGH TEMPERATURES DO NOT TOUCH WITH BARE HANDS USE THE APPROPRIATE HANDLE ONLY SPECIAL BEVERAGES HOT WATER Place a container beneath the hot water After selecting the HOT WATER option When hot water dispensing is complete steam wand press OK and wait for the programmed remove the container with the desired quantity to be dispensed This operation water quantity can be stopped by pressing STOP Repeat the procedure to dispense a new quantity of hot water After dispensing some water always remains in the lines and this may result in leaking This is a normal feature of the machine STEAM DISPENSING Steam can be used to heat milk water or other beverages SPECIAL BEVERAGES After selecting the STEAM option Steam dispe
29. h for optimum brewing For proper cleaning refer to the Milk Carafe Cleaning section see page 39 Rotate the handle clockwise to disengage the lock Remove the protection cover from the milk container connection and keep it in a clean place It is suggested to insert it in the water cover seat Place the lid back and ensure that it is closed correctly Move the handle back to its central position to allow for perfect closure Fill the carafe with cold milk Fill milk to above the MIN line but do not exceed the MAX level indicated on the carafe A Carafe holes B Carafe pins C Machine couplings D Guides for carafe pins Press the disengage buttons to allow the lid removal Ka Za Insert the carafe inclined towards the front The carafe base should be positioned on the hole E located on the drip tray Am X Ss i h 3 eg At this stage the carafe holes A are lower than the couplings C in the figure until it is hooked to the hole E located in the drip tray The carafe pins B are located at the same height of the guides D N DO NOT FORCE THE INCLINATION OF THE CARAFE The carafe will be naturally back in place REMOVING THE CARAFE The following operations show how to properly remove the carafe from the machine N DO NOT FORCE THE INCLINATION OF THE CARAFE Pull the carafe upwards until its release from the hole E located in the drip tray
30. ine allows you to adjust the right quantity of ground coffee for each product The standard adjustment for each product can be set in the BEVERAGE MENU see page 22 You may temporarily change the amount of coffee ground as well This change applies only to the brewing of the next coffee Press the button on the control panel to temporarily change the quantity of ground coffee or select the pre ground function mild dose EXPRELIA OQO medium dose 000 strong dose MENU SAECO ADAPTING SYSTEM Coffee is a natural product and its characteristics may change according to its origin blend and roast The Saeco coffee machine is equipped with a self adjusting system that allows the use of all types of coffee beans available on the market not including flavored or carmelized e The machine automatically adjusts itself in order to optimize the extraction of the coffee ensuring perfect compression of the beans to obtain a creamy espresso coffee that is able to release all the aromas regardless of the type of coffee used e The optimization process is a learning process that requires the brewing of a certain number of coffees to allow the machine to adjust the compactness of the ground coffee e Attention should be given to special blends which require grinder adjustments in order to optimize the extraction of the coffee COFFEE GRINDER ADJUSTMENT The machine allows slight adjustments to the coffee grinder to adapt it t
31. ingle type of coffee since the last reset This function enables the wash cycle for the brew group See page 30 This function enables the wash cycle for the carafe used for preparing milk beverages See page 34 Note This wash cycle is fundamental for a correct maintenance of the carafe This function enables the descaling cycle the machine shows how many litres can be dispensed before descaling See page 31 This function enables automatic cleaning of the carafe after each dispensing of milk based products Co The self cleaning function is disabled Com The self cleaning function is enabled FACTORY SETTINGS This function allows you to restore all factory settings Note By restoring the factory settings all the personal parameters are lost E MAINTENANCE BREW GROUP CLEANING CYCLE To rinse the brew group simply clean with water as shown on page 38 This wash cycle completes the maintenance process of the brew group We recommend carrying out this cycle on a monthly basis or every 500 coffees using the Saeco brew group cleaning tablets which can be purchased from Saeco Customer Service or an authorized retailer WASH CYCLES CANNOT BE STOPPED DO NOT LEAVE THE MACHINE UNATTENDED DURING THIS OPERATION Turn the SBS dial all the way to the left counter clockwise see page 11 before starting the cycle MAINTENANCE PERFORM BREW REFILL GROUP CLEANING WATER TANK BREW GROUP CLEAN CARAFE CLEANING DERE MENU
32. lection The carafe rinse function has been selected Press the button ESC to cancel the selection The selected operation requires the milk container for brewing Insert the container in the machine as specified in the manual Press the button ESC to cancel the selection Perform a descaling cycle on the machine When this message is displayed it is still possible to use the machine but its correct operation might be compromised Damages caused by failure to descale the machine are not covered by warranty The machine requests the Intenza water filter to be replaced with a new one Replace the filter as described on page 7 The alarm is displayed only if the Enable Filter function is set to ON See page 28 Flashing red light Machine in Stand by The Stand by settings can be changed Press the ly button An event has occurred which requires the machine restart Take note of the code E xx shown at the bottom Switch off the machine wait 30 seconds and then switch it on again If the problem persists contact the service centre SOS SAFETY RULES EEE IN CASE OF EMERGENCY IMMEDIATELY UNPLUG THE CORD FROM THE OUTLET ONLY USE THE APPLIANCE Indoors e For preparing coffee hot water and for frothing milk e For domestic use e This appliance is not intended for use by persons including children with reduced physical sensory or mental capabilities or lack of experience and knowledge
33. nnect turn any control to off then remove plug from wall outlet 12 Do not use appliance for other than intended use 13 5ave these instructions SAVE THESE INSTRUCTIONS CAUTION This appliance is tor household use only Any servicing other than cleaning and user maintenance should be pertormed by an authorized service center Do not immerse machine in water To reduce the risk of fire or electric shock do not disassemble the machine There are no parts inside the machine serviceable by the user Repair should be done by authorized service personnel only l Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage Never use warm or hot water to fill the water tank Use cold water only Keep your hands and the cord away from hot parts of the appliance during operation Never clean with scrubbing powders or harsh cleaners Simply use a soft cloth dampened with water For optimal taste of your coffee use purified or bottled water Periodic descaling is still recommended every 2 3 months Do not use caramelized or flavored coffee beans INSTRUCTIONS FOR THE POWER SUPPLY CORD A short power supply cord or detachable power supply cord is to be provided to reduce risks resulting trom becoming entangled in or tripping over a longer cord Longer detachable power supply cords or extension cords are available and may used if care is exercised in their use
34. nsing can be interrupted at steam wand press OK and wait for the programmed any time by pressing STOP quantity to be dispensed When steam dispensing complete remove the container with the heated beverage For better results we recommend performing slow circular movements BEVERAGE LENGTH QUICK PROGRAMMING EI BREWING MAY BE PRECEDED BY SHORT SPURTS OF MILK AND STEAM RISK OF SCALDING REFER TO THE SECTION MILK CONTAINER USE This section shows the programming procedure for the Cappuccino This is meant as an example to introduce you to the steps necessary for a quick and easy programming of all the beverages After a quick programming of the beverage it is possible to carry out a finer and more detailed adjustment by means of the BEVERAGE MENU see page 22 Place the cup or the container where Rotate the upper part of the container Hold the button pressed for 3 seconds to the cappuccino or latte macchiato will handle on the cup Use your everyday start programming be brewed cup CAPPUCCINO CAPPUCCINO CAPPUCCINO 0 E lwvevo PLEASE WAIT ES MENU OE i EN CVS The machine starts brewing coffee is Milk dispensing begins When the Once milk has been dispensed the ground and milk is heated up to prepare desired quantity has been reached press machine starts brewing the coffee When for dispensing STOP the desired quantity has been reached press STOP Beverage length has been programmed From now
35. o access the Select the menu by pressing the V machine main menu button Press the OK button to access the MACHINE MENU Er ESPRESSO M ACH INE MEN U CAPPUCCINO DISPLAY MENU m WATER MENU gp be CAFFE LUNGO SPECIAL Scrolling Selection button Saolling Selection button Selection confirmation button Exit button EI MACHINE MENU GENERAL MENU GENERAL MENU To change the machine operation settings TONE This function activates deactivates the acoustic alarms OFF To deactivate the acoustic alarms To activate the acoustic alarms ECOMODE This function enables allows you to choose how the boilers on the machine are activated to promote energy saving This function activates all the boilers each time the machine starts up to be immediately able to dispense all kinds of beverages This function entails greater energy consumption This function activates only the coffee boiler each time the machine starts up The machine saves energy but takes longer to dispense milk based beverages To set the time interval for the machine to go into stand by mode after the STAND BY last brewing The default time value is after 1 hour 15 MINUTES Press any button to turn the machine on again After performing 30 MINUTES the function diagnostics and the warm up phase the machine is again ready for use 60 MINUTES 180 MINUTES MENU DISPLAY DISPLAY MENU LANGUAGE ENGLISH The currently select
36. o children When left unattended unplug from the electrical outlet e Keep the coffee machine packaging out of the reach of children e Never direct the jet of hot water and or steam towards yourself or others Danger of scalding e Do not insert objects through the appliance s openings Danger Electrical Current e Do not pull out the plug by yanking on the power cord or touching it with wet hands e Warning Danger of burning when in contact with hot water steam and the hot water spout FAILURES e Donot use the appliance if a failure has been verified or suspected for example after being dropped Any repairs must be performed by an authorized customer service center e Do not use the appliance with a defective power cord The manufacturer or its customer service center will have to replace the power cord if damaged Caution Electrical Current e Turn off the appliance before opening the service door Danger of burns CLEANING DESCALING e For cleaning the milk and coffee circuits use only recommended detergents provided with the machine These detergents must not be used for other purposes e Before cleaning the machine the main switch must be turned to OFF 0 unplugged from the socket and cooled down e Clean the machine with neutral detergent and a damp cloth do not use abrasive sponges or steel wool pads e Keep the appliance from coming into contact with splashes of water or immersing in water Do not dry the machine part
37. o the kind of coffee used Important Note Adjustments to the coffee grinder can be made only when the grinder is being used This phase takes place during the first part of a coffee brewing The adjustment can be carried out by using the dial inside the bean hopper without coming into contact with any moving parts Press and rotate the dial one step at a time according to the indications provided on the cover Press and turn the dial one notch at a time and brew 2 3 cups of coffee this is the only way to notice differences in the grind Press and turn This setting provides a very coarse This setting provides a very fine grinding grinding Kl abJusTMENTS DISPENSING SPOUT HEIGHT ADJUSTMENT Before brewing a product and according to the kind of cup adjust the height of the dispensing spout To adjust manually move the dispensing spout as shown in the picture Note In some cases the dispensing spout can be removed to allow the use of very large containers STAND BY MODE The machine is designed for energy saving After 60 minutes of inactivity the machine goes into stand by mode the boiler is no longer heated and all the devices turn off Power consumption is reduced to a minimum Press any button to turn the machine on again The machine status can be manually changed to stand by mode by holding the stand by button pressed for 3 seconds Note 1 The stand by mode cannot be activated if the service door is left
38. rewing Coffee is slightly dampened before brewing so as to bring out the full aroma of the coffee which acquires an excellent taste OFF prewbrewing function is not performed LOW prewbrewing function is active HIGH prebrewing function is longer in order to bring out the coffee taste This section allows you to program the temperature for coffee brewing LOW low temperature NORMAL medium temperature HIGH high temperature This section allows to program the quantity of water to be used for each selected beverage The strip allows you to determine exactly the quantity of water for preparing coffee Fb ESPRESSO x CAFFE LUNGO SPECIAL MILK QUANTITY Ey ESPRESSO ER d CAFFE LUNGO SPECIAL WATER QUANTITY HI BEVERAGE MENU ES CAPPUCCINO CAPPUCCINO COFFEE QUANTITY PREBREWING COFFEE TEMPERATURE DENS MENU This section allows you to program the quantity of milk for each selected beverage The strip allows you to determine exactly the quantity of milk to be dispensed SS HOT WATER CAPPUCCINO WATER QUANTITY DEFAULT PESE MENU This section allows you to program the quantity of water to be dispensed when pressing the hot water button The strip allows you to determine exactly the quantity of water to be dispensed MACHINE MENU E The machine allows you to customize the operation settings MENU EXPRELLA BEVERAGE MENU MACHINE MENU Cmn Press the MENU button t
39. s and similar apparatus Part 1 Emission EN 55014 1 2006 e Electromagnetic compatibility EMC Part 3 Limits Section 2 Limits for harmonic current emissions equipment input current lt 16A for phase EN 61000 3 2 2006 e Electromagnetic compatibility EMC Part 3 Limits Section 3 Limitation of voltage changes voltage fluctuations and flicker in publiclow voltage supply systems for equipment with rated current lt 16 A for phase and not subject to conditional connection EN 61000 3 3 1995 corr 1997 A1 2001 A2 2005 e Electromagnetic compatibility Requirements for household appliances electric tools and similar apparatus Part 2 Immunity Product family standard EN 55014 2 1997 A1 2001 following the provisions of the Directives EC 2006 95 EC 2004 108 Gaggio Montano li 28 04 2009 PHILIPS The manufacturer reserves the right to change the features of the product without prior notice www philips com saeco del 15 05 10 Type HD8854 HD8856 Cod 15001999 Rev O
40. s in conventional or microwave ovens e The machine and its components must be cleaned and washed after the machine has not been used for a certain period REPLACEMENT PARTS For safety reasons use only original replacement parts and original accessories WASTE DISPOSAL The packing materials can be recycled Appliance unplug the appliance and cut the power cord Deliver the appliance and power cord to a service center or public waste disposal facility This product complies with eu directive 2002 96 ec The symbol on the product or on its packaging indicates that this product may not be treated as household waste Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment By ensuring this product is disposed of correctly you will help prevent potential negative consequences for the environment and human health which could otherwise be caused by inappropriate waste handling of this product For more detailed information about recycling of this product please contact your local city office your household waste disposal service or the shop where you purchased the product FIRE SAFETY In case of fire use Carbon Dioxide extinguishers CO Do not use water or dry powder extinguishers ADDITIONAL INFORMATION FOR THE CORRECT USE OF THE INTENZA WATER FILTER To correctly use the Intenza water filter please consider the following instructions 1 Store the Intenza water
41. shocks and or fire e be crushed and or come in contact with sharp surfaces e be used to move the machine e be used if damaged e be handled with damp or wet hands e be wound in a coil when the machine is being operated e Be tampered with INSTALLATION e Choose a solid stationary flat surface no more than 2 of inclination Do not install the machine in areas where water could be sprayed e Optimal operational temperature 10 C 40 C 50 104 degrees Fahrenheit e Maximum humidity 90 e The machine should be installed in an adequately lit ventilated hygienic location and the electric socket should be within easy reach e Do not place on heated surfaces e Install it at least 10 cm 4 from the walls and cooking surfaces e Do not use in places where the temperature may drop to a level equal to and or lower than 0 C 32 degrees Fahrenheit If the machine has been exposed to such conditions notify the customer service center who will have to carry out a safety check e Do not use the machine near inflammable and or explosive substances e The machine must not be used in an explosive or volatile atmosphere or where there is a high concentration of dust or oily substances suspended in the air e Do not install the machine on top of other appliances E SAFETY RULES DANGERS e The appliance must not be used by children and persons who have not been informed of its operation e The appliance is dangerous t
42. unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety e Children should be supervised to ensure that they do not play with the appliance PRECAUTIONS FOR THE USE OF THE MACHINE e Do not use the machine for purposes other than those indicated above in order to avoid danger Do not introduce any substances other than those indicated in the instruction manual e During the normal filling of any reservoirs all nearby reservoirs must be closed e Fill the water tank only with fresh drinking water Hot water and or any other liquid may damage the machine e Do not use carbonated water e Do not put fingers or any material other than coffee beans in the coffee grinder e Before manipulating the coffee grinder turn of the machine main switch and unplug the cord e Do not put instant coffee or whole bean coffee in the ground coffee container e Only use your finger when operating the LCD screen CONNECTION TO ELECTRICAL POWER The connection to the electrical network must be carried out in accordance with the safety regulations in force in the user s country The machine must be connected to a socket which is e compatible with the type of plug installed on the machine e suitably sized to comply with the data on the plate attached to the inside of the appliance e effectively grounded The power cord must not e come into contact with any type of liquid danger of electric
43. y pressing STOP STOP m MENU avai The machine finishes brewing automatically on the basis of the quantity determined by the factory settings To customize this quantity see page 22 BEVERAGE BREWING WITH PRE GROUND COFFEE The machine allows you to use pre ground and decaffeinated coffee Pre ground coffee must be poured into the bypass doser positioned on the top of the machine Only use ground coffee for espresso machines and never coffee beans or instant coffee see the beverage programming section on page 22 This example shows how to brew an espresso by using pre ground coffee INSERT GROUND COFFEE AND PRESS OK OK ESC DES MENU JAN mam Roe BE SR INO A message reminds the user to pour ground coffee into the bypass doser WARNING ONLY PUT PRE GROUND COFFEE INTO THE BYPASS DOSER WHEN YOU WISH TO BREW THIS TYPE OF PRODUCT ONLY INSERT ONE SCOOP OF GROUND COFFEE AT A TIME TWO COFFEES CANNOT BE BREWED AT THE SAME MENU PETS N Press the opti dose once or more until the icon appears on the display screen Lift the door and open it Pour ground coffee in the appropriate compartment using the measuring scoop provided TIME WHEN USING THIS FUNCTION Note If brewing does not start within 30 seconds from the appearance of the message in step 4 the machine will return to the main menu and discharge any inserted coffee into the used grounds drawer If no pre ground
44. y pressing STOP The machine requires a certain waiting time because the ECOMODE function is activated to allow energy saving Preparing cappuccino and other milk beverages can be a quicker operation if the ECOMODE function is deactivated this however at the expense of energy saving This function can only be deactivated by means of the MACHINE MENU see page 26 CICLO PULIZIA CLEAN Wait a few seconds The machine starts the automatic cleaning process if enabled see page 29 k i At the end remove the cup with the Upon completion of the cleaning cycle cappuccino and place the handle back to remove the milk carafe and put it in the the initial position refrigerator N NEVER SEIZE THE CARAFE HANDLE DURING THE CLEANING CYCLE RISK OF SCALDING The procedure to prepare a latte macchiato a milk and coffee or a hot milk is similar please refer to the special beverages section see page 18 CLEANING CYCLE The machine allows executing a quick cleaning cycle at any time The cleaning cyde can be executed before and or after the beverage brewing This option allows you to manage the container cleaning process as desired The cleaning process may be used also for circuit sanitization after a long period of inactivity Place the container as described on Press the cleaning cycle button The At the end it is possible to remove the pages 12 and 13 The cleaning cycle only machine executes an additional cl
Download Pdf Manuals
Related Search